Transmission HONDA PILOT 2007 1.G Owner's Manual

Putane
ww
as
he r
on
t
he f iller bolt,
then reinstall the f iller bolt and
tighten it securely. Tightening
torque:
The dif f erential should be drained
and ref illed with new f luid according
to the time and distance recommen-
dations in the maintenance schedule.
GL5 with a viscosity of SAE 90 or
80W-90, and have your dealer
replace the transfer assembly fluid.
Check the f luid level with the
dif f erential at normal operating
temperature and the vehicle sitting
on level ground. Remove the
dif f erential f luid f iller bolt and
washer, and caref ully f eel inside the
bolt hole with your f inger. The f luid
level should be up to the edge of the
bolt hole. If it is not, slowly add
VTM-4 Dif f erential Fluid until it
starts to run out of the hole.
Always use Honda ATF-Z1
(automatic transmission f luid). If
it’s not available, you may use a
DEXRON
III automatic
transmission f luid as a temporary
replacement. However, continued
use can affect the shift quality.
Have the transmission f lushed and
ref illed with Honda ATF-Z1 by
your dealer as soon as it is
convenient.
Insert the dipstick all the way back
into the transmission securely as
shown in the illustration.
The transmission should be drained
and ref illed with new f luid according
to the time and distance recommen-
dations in the maintenance schedule. The transfer assembly should be
drained and refilled with new fluid
when this service is indicated by a
maintenance message on the
information display.
Always use Hypoid gear oil GL4 or
6.
4WD models only
Transfer Assembly Fluid
Dif f erential Oil
A utomatic Transmission Fluid, Dif f erential Oil, Transfer Assembly Fluid
Maint enance
245
FILLER BOLT
CORRECT LEVEL
33 lbf·ft (45 N·m , 4.6 kgf·m)

Fill the f uel tank.
Change the engine oil and f ilter.Block the rear wheels.
Wash and dry the exterior
completely.
Cleantheinterior.Makesurethe
carpeting, floor mats, etc., are
completely dry.
If you need to park your vehicle f or
an extended period (more than 1
month), there are several things you
should do to prepare it f or storage.
Proper preparation helps prevent
deterioration and makes it easier to
get your vehicle back on the road. If
possible, store your vehicle indoors. Leave one window open slightly (if
the vehicle is being stored
indoors).Cover the vehicle with a
‘‘breathable’’ cover, one made
f rom a porous material such as
cotton. Non-porous materials, such
as plastic sheeting, trap moisture,
which can damage the paint.
Support the f ront wiper blade
arms with a f olded towel or rag so
they do not touch the windshield. Disconnect the battery.
Leave the parking brake off. Put
the transmission in Park. To minimize sticking, apply a
silicone spray lubricant to all door
and tailgate seals. Also, apply a
vehiclebodywaxtothepainted
surfaces that mate with the door
and tailgate seals.If possible, periodically run the
engine until it reaches f ull
operating temperature (the
cooling f ans cycle on and of f
twice). Pref erably, do this once a
month.
If the vehicle is to be stored f or a
longer period, it should be
supported on jackstands so the
tires are of f the ground.
Vehicle Storage
Maint enance
263

CONT INUED
If you have a f lat tire while driving,
stop in a saf e place to change it.
Drive slowly along the shoulder until
you get to an exit or an area to stop
that is far away from the traffic lanes.Park the vehicle on f irm, level, and
non-slippery ground. Put the
transmission in Park. Apply the
parking brake.
If you are towing a trailer, unhitch
it.
Turn on the hazard warning lights,
and turn the ignition switch to the
LOCK (0) position. Have all
passengers get out of the vehicle
while you change the tire.Turn the jack’s end bracket
counterclockwise to loosen it, then
remove the jack and tools. Thetoolsandjackarebehinda
cover in the cargo area on the
driver’s side. Remove the cover by
pushing the top of the cover.
2. 1. 3.
4.
Changing a Flat Tire
T aking Care of t he Unexpect ed
267
SPARE TIRE
TOOLS
COVER
JACK
The vehicle can easily roll off
the jack, seriously injuring
anyone underneath.
Follow the directions for
changing a tire exactly, and
never get under the vehicle
when it is supported only by the
jack.

Diagnosing why the engine won’t
start falls into two areas, depending
on what you hear when you turn the
ignition switch to the START (III)
position: You hear nothing, or almost
nothing. The engine’s starter
motor does not operate at all, or
operates very slowly.
You can hear the starter motor
operating normally, or the starter
motor sounds like it is spinning
faster than normal, but the engine
does not start up and run.
Wh en you turn the ignition switch to
the START (III) position, you do not
hear the normal noise of the engine
trying to start. You may hear a
clicking sound, a series of clicks, or
nothing at all. Check
the transmission interlock.
The transmission must be in Park
or neutral or the starter will not
operate.
Are you using the proper starting
procedure? Refer to
on page .
In
this case, the starter motor’s
speed sounds normal, or even faster
than normal, when you turn the
ignition switch to the START (III)
position, but the engine does not run.
Check these things: Turn
the ignition switch to the
START (III) position. If the
headlights do not dim, check the
condition of the fuses. If the fuses
areOK,thereisprobably
something wrong with the
electrical circuit for the ignition
switch or starter motor. You will
need a qualified technician to
determine the problem. See
on page .
Turn
the ignition switch to the ON
(II) position. Turn on the
headlights, and check their
brightness. If the headlights are
very dim or do not come on at all,
the battery is discharged. See
on page . If
the headlights dim noticeably or
go out when you try to start the
engine, either the battery is
discharged or the connections are
co rroded. Check the condition of
the battery and terminal
connections (see page ). You
canthentryjump startingthe
vehicle from a booster battery
(see page ).
272
279 199262
272
CONT INUED
Nothing Happens or the Starter
Motor Operates Very Slowly Starting the
Engine
T he Starter Operates Normally
Emergency T owing Jump Starting
If theEngineWon’tStart
T aking Care of t he Unexpect ed
271

´´
There
may be an electrical
problem, such as no power to the
fuel pump. Check all the fuses
(see page ). Although
this seems like a simple
procedure, you should take several
precau tions. Open
the hood, and check the
physical condition of the battery.
In very cold weather, check the
condition of the electrolyte. If it
seems slushy or frozen, do not try
jump starting until it thaws.
Connect one jumper cable to the
positive ( ) terminal on your
battery. Connect the other end to
the positive ( ) terminal on the
booster battery.
Do
you have fuel? Check the fuel
gauge; the low fuel indicator may
not be working.
You cannot start your vehicle by
pushing or pulling it.
Are
you using a properly coded
key? An improperly coded key will
cause the immobilizer system
indicator in the instrument panel
to blink rapidly (see page ).
If youfindnothingwrong,youwill
need a qualif ied mechanic to f ind the
problem. See
on page . Turn of f all electrical accessories:
heater, A/C, climate control, audio
system, lights, etc. Put the
transmission in Park, and set the
parking brake. To jump start your vehicle:
1.
2.
3.
64
279 279
If the Engine Won’t Start, Jump Starting
Jump Starting
Emergency T owing
272
A battery can explode if you do
not follow the correct procedure,
seriously injuring anyone
nearby.
Keep all sparks, open flames,
and smoking materials away
from the battery. If a battery sits in extreme cold, the
electrolyte inside can f reeze.
Attempting to jump start with a f rozen
battery can cause it to rupture.

If you do not see steam or spray,
leave the engine running, and
watch the temperature gauge. If
the high heat is due to overloading,
the engine should start to cool
down almost immediately. If it
does, wait until the temperatu re
gauge comes down to the midpoint,
th en continue driving.
If the temperatu re gauge stays at
the red mark, turn off the engine.
Look for any obvious coolant leaks,
such as a split radiator hose.
Everything is still extremely hot,
so use caution. If you find a leak, it
must be repaired bef ore you
continue driving (see on page ).
If you see steam and/or spray
coming f rom under the hood, turn
of f the engine. Wait until you see
no more signs of steam or spray,
then open the hood.
The pointer of your vehicle’s
temperature gauge should stay in
the midrange under most conditions.
If it climbs to the red mark, you
should determine the reason (hot
day, driving up a steep hill, etc.).
If your vehicle overheats, you should
take immediate action. The only
indication may be the temperature
gauge climbing to or above the red
mark. Or you may see steam or
spray coming f rom under the hood.
If you don’t f ind an obvious leak,
check the coolant level in the
radiator reserve tank (see page). Add coolant if the level is
below the MIN mark.
Saf ely pull to the side of the road.
Put the transmission in neutral or
Park, and set the parking brake.
Turn of f all the accessories, and
turn on the hazard warning lights.
5.
6. 4.
1.
2. 3.
279
190
If theEngineOverheats
Emergency
Towing
274
Steam and spray from an
overheated engine can
seriously scald you.
Do not open the hood if steam
is coming out.
Driving with the temperature gauge
pointer at the red mark can cause
serious damage to the engine.

If your vehicle’s battery has been
disconnected or gone dead, these
codes are erased. It takes at least
three days of driving under various
conditions to set the codes again.
To check if they are set, turn the
ignition switch to the ON (II)
position without starting the engine.
The malfunction indicator lamp will
come on for 20 seconds. If it then
goes off, the readiness codes are set.
If it blinks 5 times, the readiness
codes are not set. If possible, do not
take your vehicle for a state
emissions test until the readiness
codes are set. Refer to
for more
info rmation (see page ).
If
this indicator comes on
while driving, it means one
of the engine’s emission control
systems may have a problem. Even
though you may feel no difference in
your vehicle’s performance,
continued operation may cause
serious damage.
If you have recently refueled your
vehicle, the indicator coming on
could be due to a loose or missing
fu el fill cap. You will also see a
‘‘CHECK FUEL CAP’’ message on
the information display. Tighten the
cap until it clicks at least once (see
page ). Tightening the cap will
not turn the indicator of f
immediately; it takes at least three
days of normal driving.
If the indicator remains on or the
f uel cap was not loose or missing,
have the vehicle checked by the
dealer as soon as possible. If the malf unction indicator lamp
comes on along with the ‘‘D’’
indicator, there is a problem in the
automatic transmission control
system.
Your vehicle has certain ‘‘readiness
codes’’ that are part of the on-board
diagnostics f or the emissions
systems. In some states, part of the
emissions testing is to make sure
these codes are set. If they are not
set, the test cannot be completed.
298
187
State
Emissions T esting
Readiness Codes
Malf unction Indicator L amp
T aking Care of t he Unexpect ed
277
If you keep driving with the
malf unction indicator lamp on, you can
damage your vehicle’s emissions
controls and the engine. Those repairs
may not be covered by your vehicle’s
warranties.

The transmission number is on a
label on top of the transmission. The engine number is stamped into
the engine block. It is on the f ront.
Identif ication Numbers
Technical Inf ormation
287
ENGINE NUMBERAUTOMATIC TRANSMISSION NUMBER

µµÎ
Î
Î
Î
µ
ÎÎ Î
Î
Specif ications
288
Dimensions
Weights
Air Conditioning
Battery Capacities1.93 US gal (7.3
)
2.43 US gal (9.2)
4.5 US qt (4.3
)
4.2 US qt (4.0
)
5.3 US qt (5.0
)
20.34 US gal (77.0
)
188.0 in (4,775 mm)
76.5 in (1,943 mm)
ND-OIL8
24.7 26.5 oz (700 750 g) HFC-134a (R-134a)
Length
Width
Height
Wheelbase
Track 66.3 in (1,685 mm)
106.3 in (2,700 mm) 70.5 in (1,790 mm)
Gross vehicle weight rating
Gross combined weight
rating (GCWR) See the tire information label atta-
ched to the driver’s doorjamb.
9,700 lbs (4,400 kg)
Equipped with transmission fluid cooler and power steering
fluid cooler.
The GCWR must be reduced 2 percent for every 1,000 feet (305
meters) of elevation.
Refrigerant type
Charge quantity
Lubricant type 77.5 in (1,968 mm)
71.7 in (1,821 mm)
70.1 in (1,780 mm)
71.3 in (1,811 mm)
66.5 in (1,690 mm)
66.5 in (1,690 mm)
66.7 in (1,694 mm)
12 V 20 AH/5 HR
Capacity Excluding the oil remaining in the engine 0.193 US gal (0.73
)
Including the coolant in the reserve tank and that remaining in the
engine
Reserve tank capacity: 2.79 US qt (2.64
)
4.8 US qt (4.5
)
Fuel tank
Engine
coolant
Engine oil
Automatic
transmission
fluid
Rear
differential
fluid (4WD)
Windshield
washer
reservoir
8.3 US qt (7.9
)
3.5 US qt (3.3
)
8.9 US qt (8.4
)
4.0 US qt (3.8
)
Approx.
1:
2:
1:
2: Front
Rear
4WD
2WD
LX
EX
LX
EX
LX
EX
Front
Rear
4WD
2WD Change
Total
Change
Including
filter
Without
filter
Total
Change
Total
Change 4WD
2WD
4WD
2WD
2
1 1
2

CONT INUED
...
Accessories and Modif ications .191
ACCESSORY (Ignition Key
.......................................
Position) .81
............
Accessory Power Sockets .101
...........................
AC Power Outlet .102
....................
Additives, Engine Oil .239
...............
AdvancedAirbagSystem .30
.............................
Airbag (SRS) . 11, 25
..........
Airbag System Components .25
..............
Air Conditioning System .106
.....................
Rear A/C Control .113
.......................
Air Pressure, Tires .258
......................................
Antif reeze .242
...............
Anti-lock Brakes (ABS) .209
...............................
Indicator . 63, 210
...................................
Operation .209
..............
Anti-thef t, Audio System .139
.
Anti-thef t Steering Column Lock .81
................................
Audio System .115
...
Automatic Seat Belt Tensioners .23
...
Automatic Lighting Off Feature .76
.............
Automatic Speed Control .175
..............
Automatic Transmission .200
..........................
Capacity, Fluid .288 ...............
Checking Fluid Level .244
.......................................
Shif ting .200
.
Shif t Lever Position Indicator .200
................
Shif t Lever Positions .201
....................
Shif t Lock Release .203
Battery Charging System ...........................
Indicator . 62, 276
............................
Jump Starting .272
..............................
Maintenance .262
............................
Specif ications .289
..............................
Bef ore Driving .185
..................................
Belts, Seat . 10, 21
...........................
Beverage Holders .99
..................................
Booster Seats .54
Brakes
...........
Anti-lock System (ABS) .209
.............
Break-in, New Linings .186
....................
Bulb Replacement .252
...........................................
Fluid .246
.........................................
Parking .97
.................
System Indicator . 63, 278
........................
Wear Indicators .209 .............................
Braking System .208
.................
Break-in, New Vehicle .186
..
Brightness Control, Instruments .76
........................
Brights, Headlights .75
Bulb Replacement
..........................
Back-up Lights .252
.....................
Brake Lights . 252, 253
................
Front Parking Lights .249
........
Front Side Marker Lights .249
.................................
Headlights .248
........
High-mount Brake Lights . 253
.................................
Rear Bulbs .252
............................
Specif ications .289
.............
Turn Signal Light . 249, 252
..............................
Bulbs, Halogen .248
............................
Capacities Chart .288
.............
Carbon Monoxide Hazard . 57
.............................
Carrying Cargo .193
.............
CAUTION, Explanation of . iii
..........................
CD Changer . 131, 134
.......................................
CD Player .130
Index
A
B
C
INDEX
I