radio HONDA PILOT 2012 2.G Owner's Manual
[x] Cancel search | Manufacturer: HONDA, Model Year: 2012, Model line: PILOT, Model: HONDA PILOT 2012 2.GPages: 681, PDF Size: 15.06 MB
Page 248 of 681
The XM satellites are in orbit over
the equator; therefore, objects south
of the vehicle may cause satellite
reception interruptions. To help
compensate f or this, ground-based
repeaters are placed in major
metropolitan areas.
Satellite signals are more likely to be
blocked by tall buildings and
mountains the f arther north you
travel f rom the equator. Carrying
large items on a roof rack can also
block the signal.
Depending on where you drive, you
may experience reception problems.
Interf erence can be caused by any of
these conditions:Driving on the north side of an
east/west mountain road.
Driving on the north side of a
large commercial truck on an
east/west road.
Driving in tunnels. Driving on a road beside a vertical
wall, steep clif f , or hill to the south
of you.
Driving on the lower level of a
multi-tiered road.
Large items carried on a roof rack.
CONT INUED
Playing t he XMRadio (EX-L model wit hout navigat ion syst em)
Features
241
Signal may be blocked by
mountains or large obstacles to
the south.
Signal weaker in
these areas.
SATELLITE GROUND REPEATER
Main MenuTable of Contents
Page 249 of 681
Driving on a single lane road
alongside dense trees taller than
50 ft. (15 m) to the south of you.If your XM Radio service has expired
or you purchased your vehicle f rom
a previous owner, you can listen to a
sampling of the broadcasts
available
on XM Radio. With the ignition
switch in the ACCESSORY (I) or the
ON (II) position, press the
button. A variety of music
types and styles will play.
If you decide to purchase XM radio
service, contact XM Radio at ,orat
1-800-852-9696. In Canada, contact
XM CANADA
at , or
at 1-877-209-0079. You will need to
give them your radio I.D. number
and your credit card number. To get
your radio I.D. number, press the button, then turn the
selector knob until ‘‘CH 000
Page 252 of 681
To load or play a disc, the ignition
switch must be in the ACCESSORY
(I) or ON (II) position.
You operate the disc player with the
same controls used f or the radio. To
select the disc player, press the CD
button. You will see ‘‘CD
Page 255 of 681
µ
Insert a disc about half way into the
disc slot. The drive will pull the disc
intherestof thewaytoplayit.You
operate the disc player with the
same controls used f or the radio.
The number of the current track is
showninthedisplay.Whenplayinga
disc in MP3, WMA or AAC, the
numbers of the current f older and
f ile are shown. The system will
continuously play a disc until you
change modes.
For inf ormation on how to handle
and protect compact discs, see page . To move rapidly within a track or f ile,
press and hold either side ( or
) of the SKIP bar. When you insert a CD f or the f irst
time, the recording CD prompt will
appear on the display. If you select
‘‘Yes,
Page 306 of 681
Playing the FM/A M Radio (Models with navigation syst em)
Features
Wit hout rear ent ert ainment syst em Wit h rear ent ert ainment syst em
299
AM/FM
BUTTON
POWER/
VOLUME KNOB
AUDIO
BUTTON TUNE/SOUND KNOB
PRESET
BUTTONS
SCAN
BUTTON AUDIO SCREEN
INTERFACE DIAL
POWER/
VOLUMEKNOB
SCAN
BUTTON
AUDIO
BUTTON
AM/FM
BUTTON
TITLE
BUTTON
INTERFACE DIAL PRESET
BUTTONS
TUNE/SOUND KNOB
Main MenuTable of Contents
Page 307 of 681
µUse the TUNE knob to
tune the radio to a desired frequency.
Turn the knob right to tune to a
higher f requency, or lef t to tune to a
lower f requency. To tune with the
interf ace dial, push the selector
down, and turn the knob to TUNE.
Then press ENTER on the selector,
andturntheknobtothedesired
f requency. To exit the TUNE mode,
press ENTER on the selector.
The ignition switch must be in the
ACCESSORY (I) or the ON (II)
position. Press the AUDIO button to
view the audio control display. Turn
the system on by pressing the
power/volume knob, the AM, or FM
button. Adjust the volume by turning
the power/volume knob.
On the AM band, AM noise
reduction turns on automatically.
You can use any of f ive methods to
f ind radio stations on the selected
band: tune, skip (seek), scan, the
preset buttons, and auto select.
The band and f requency that the
radio was last tuned to are shown on
the display. To change bands, press
the AM/FM button. You can also
change bands by pushing the
interf ace selector up. Each time you
push it up, the band will change to
FM1, FM2 or AM. On the FM bands,
STEREO will be shown on the
navigation screen and ST on the
center display, if the station is
broadcasting in stereo. Stereo
reproduction on AM is not available.
TUNE
To Play the FM/AM Radio
To Select a Station
Playing the FM/A M Radio (Models with navigation syst em)
300
STEREO INDICATOR TUNE
BAND
Main MenuTable of Contents
Page 308 of 681
µ
µ
The scan f unction samples
all stations with strong signals on the
selected band. To activate it, press
the SCAN button, then release it.
The skip (seek)
f unction searches up and down f rom
the current f requency to f ind a
station with a strong signal. To
activate it, press either side ( or ) of the SKIP bar, then release
it. To scan with the interf ace dial, push
the interf ace selector down, and turn
the interf ace dial to select Scan, then
press ENTER on the interf ace
selector.
The system will scan f or a station
with a strong signal. When it f inds a
strong signal, it will stop and play
that station for about 10 seconds. If
you do nothing, the system will then
scan f or the next strong station and
play it f or 10 seconds. When it plays
a station that you want to listen to,
press the SCAN button again.
CONT INUED
SCAN
SK IP (SEEK )
Playing the FM/A M Radio (Models with navigation syst em)
Features
301
Main MenuTable of Contents
Page 309 of 681
µ
µ
If you are
traveling and can no longer receive
your preset stations, you can use the
auto select feature to find stations in
the local area.
Each preset button or
preset icon can store one f requency
on AM and two f requencies on FM.
Select the desired band, AM or
FM. FM1 and FM2 let you store
twosetsof FMfrequencieswith
the preset buttons (on-screen
icons).
Usethetune,seek,orscan
function to tune the radio to a
desired station.
Press the preset button, and hold
it until you hear a beep. You can
also store f requencies with the
interf ace dial. Select the preset
icon you want to store the
f requency on, then press ENTER
on the interf ace selector, and hold
it f or more than 2 seconds.
Repeat steps 1 through 3 to store a
total of six stations on AM and
twelve stations on FM. Push the interf ace selector down to
display the AUDIO MENU. Turn the
interf ace dial to select A.SEL, then
press ENTER on the interf ace
selector. Turn the interf ace dial to
select ON, then press ENTER on the
interf ace selector. You will see A.SEL on the screen and the system
goes into auto select mode for
several seconds.
The system stores the f requencies of
six AM and twelve FM stations in
the preset buttons (icons).
You will see ‘‘0
Page 310 of 681
On the FM band, you can select a
favorite station and display the
program service name provided by
the radio data system (RDS).
For inf ormation on FM/AM radio
f requencies and reception, see page
.
The RDS INFO display f unction
shows the name of the station you
are listening to. With the audio
system on and the FM band selected,
you can turn this f unction on or of f . To switch the RDS INFO display
f unction on and of f , press and
release the TITLE button. With the
system on, you will see the ‘‘RDS
INFO ON
Page 312 of 681
CONT INUED
Turn the interf ace dial to select an
RDS category. You can use the
search or scan f unction to f ind radio
stations on the selected RDS
category by pressing the interf ace
selector to the left or the right. Press
ENTER to set your selection.This f unction searches up and down
f or strong signal f requencies that
carry the selected RDS category
inf ormation. This can help you to
find a station in your favorite
category. To activate it, press and
release either side ( or ) of
the SKIP bar. You will also see the
selected RDS category name
blinking in the center display while
searching it. When the system finds
a station, the selected RDS category
name will be displayed again f or
about 10 seconds, and the system
stops searching.
If the system does not find a station,
‘‘NOTHING