lights HONDA PRELUDE 1992 Owner's Guide

Lights
5. Push the bulb holder into the
turn signal assembly and turn it
clockwise until it locks.
6. Test the turn signals to make sure the new bulb is working.
7. Put the turn signal assembly into
the bumper. Make sure the tab
on the turn signal assembly fits
into the bumper slot. Tighten the
mounting screw.

Replacing a High-moun
t
Brake Light Bulb

1. Remove the cover by pulling it

down and sliding it forward.

2. Determin e
which bulb is burned

out.

3. Pul
l
the bulb straight out of its

socket.
Push the new bulb straight into
the socket until it bottoms.

4. Tes t
the lights to make sure the

new bulb is working.

5. Reinstal
l
the cover by sliding it

into position and pushing it up.

Maintenance
COVER
ProCarManuals.comMain Menu Table of Contents s t

Lights

Replacing Rear Bulbs

1. Open the trunk and the taillight
assembly cover.

2. Use
a phillips head screwdriver

to remove the two screws from
the bulb holder. Remove the
holder from the taillight assem-
bly.

3. Try the tail/stoplights, rear turn

signals and back-up lights to
verify which bulb needs replac- ing. Remove that bulb from the
socket by pushing it in slightly
and turning it counterclockwise.

4. Instal l
the new bulb in the socket.

Test it to make sure it works.

5. Reinstal
l
the bulb holder assem-
bly. Install the two screws and
tighten them securely.

Maintenance

COVERProCarManuals.comMain Menu Table of Contents s t

Lights

Replacing a Rear Side Marker
Light Bulb

1. Use a phillips-head screwdriver
to loosen the side marker assem-
bly mounting screw.

2. Remove
the assembly from the
fender by pulling out the back
edge and sliding the assembly

backwards.
3. Remove the socket from the

light assembly by turning it
counterclockwise.

4. Remov
e
the bulb from the socket

by pulling it straight out.
Install the new bulb. Turn on the
headlights to test the bulb.

5. Inser t
the socket in the assembly.

Turn it clockwise to lock it in
place.

6. Reinstal
l
the side marker assem-
bly in the fender. Tighten the
mounting screw securely.

Maintenance

SCREWProCarManuals.comMain Menu Table of Contents s t

Lights

Replacing a Rear License
Bulb

1. Remove the two screws and remove the license light assem-

bly.
2. Remove the lens from the rubber
seal and the metal
cover.
3. Pull the bulb straight out of its
socket. Push the new bulb in
until it bottoms in
the socket.4. Turn on the parking lights and
check that the new bulb is

working.

5. Reinstall the cover and the lens.
Put the license light assembly in
place. Reinstall the two screws
and tighten them securely.
Replacing
Interior and Trunk
Light Bulbs

1. Remove the lens by carefully

prying on the edge of the lens in
the middle with a fingernail file
or a small flat-tip screwdriver.
Do not pry on the edge of the
housing around the lens.

CONTINUED

Maintenance

INTERIOR
LIGH
TProCarManuals.comMain Menu Table of Contents s t

Lights

2. Remove the bulb by pulling it straight out of its metal tabs.
3. Push the new bulb into the metal tabs. Snap the lens back in place.

Maintenance

TRUNK LIGHTProCarManuals.comMain Menu Table of Contents s t

Changing a Flat Tire
If you
have a flat tire while driving,
stop in a safe place to change it.
Stopping in traffic or on the shoul-
der of a busy road is dangerous.
Drive slowly along the shoulder
until you get to an exit or an area to stop that is far away from the traf-
fic lanes.
1. Park the car on firm, level ground away from traffic. Turnon the hazard warning lights and
turn the ignition to LOCK (0). 2. Put the transmission in Park
(automatic) or Reverse (5-speed).
Set the parking brake.
3. Open the trunk. Raise the trunk floor by lifting up on the back

edge.

4. Take the tool kit out of the trunk. 5. Unscrew the wing bolt and take
the spare tire out of the trunk.

Taking Care of the Unexpected
CONTINUED

The car can easily roll off the

jack, seriously injuring anyone
underneath.

Follow the directions for chang-

ing a tire exactly, and never

get under the car when it is

supported only by the jack.
TRUNK FLOOR

JACK

SPARE TIRE

TOOL KITProCarManuals.comMain Menu Table of Contents s t

If Your Engine Won't Start

Diagnosing why your engine won't
start falls into two areas, depending
on what you hear when you turn
the key to START (III): You hear nothing, or almost
nothing. The engine's starter
motor does not operate at all, or
operates very slowly.
You can hear the starter motor
operating normally, but the
engine does not start up and run. Nothing Happens or the
Starter Motor Operates Very
Slowly
When you turn the ignition switchto START (III), you do not hear the
normal noise of the engine trying to
start. You may hear
a clicking
sound or series of clicks, or nothing
at all.
Check these things:
Check the

transmission interlock.
If you have a 5-speed, the clutch
pedal must be pushed all the way
to the floor or the starter will not operate. With an automatic
transmission, it must be in Park
or Neutral.
Turn the ignition switch to ON
(II). Turn on the headlights and
check their brightness. If the
headlights are very dim or don't
light at all, the battery is dis-
charged.
See Jump Starting on

page 191
.
Turn the ignition switch to

START (III). If the headlights do

not dim, check the condition of

the fuses. If the fuses are OK,

there is probably something
wrong with the electrical circuit

for the ignition switch or starter
motor. You will need a qualified

technician to determine the

problem. (See Towing on page
202.)

If the headlights dim noticeably
or go out when you try to start
the engine, either the battery is

discharged or the connections

are corroded. Check the condi-

tion of the battery and terminal
connections (see page 153 ). You

can then try jump starting the

car from a booster battery (see
page 191).

Taking Care of the UnexpectedProCarManuals.comMain Menu Table of Contents s t

If Your Engine Won't Start, Jump Starting

The Starter Operates
Normally

In this case, the starter motor
sounds normal when you turn the
ignition switch to START (III), but
the engine does not run. Are you using the proper starting
procedure? Refer to Starting
the Engine on page 109 . Do you have gas? Turn the
ignition switch to ON (II) for a
minute and watch the fuel gauge.
There may be an electrical
problem, such as no power to the
fuel pump. Check all the fuses
(see page 199 ).

If you find nothing wrong, you will
need a qualified technician to find
the problem. See Towing on page
202.
Jump Starting

If your car's battery has run down,
you may be able to start the engine
by using a booster battery. Although this seems like a simple
procedure, there are several precau-
tions you should take. Follow the
directions closely.
You cannot start a Honda with an
automatic transmision by pushingor pulling it. To jump start your car:
1. Open the hood and check the physical condition of the battery
(see page 152 ). In very cold
weather, check the condition of the electrolyte. If it seems slushy
or like ice, do not try jump
starting until it thaws.
If a battery sits in extreme cold, the
electrolyte inside can freeze.
Attempting to jump start with a frozen battery can cause it to
rupture or explode.
2. Turn off all the electrical acces- sories: heater, A/C, stereo system,
lights, etc. Put the transmission in Neutral
or Park and set the parking
brake.

Taking Care of the Unexpected
CONTINUED
A battery can explode if you
do not follow the correct

procedure, seriously injuring

anyone nearby.

Keep all sparks, open flames,

and smoking materials away

from the battery.
NOTICE
ProCarManuals.comMain Menu Table of Contents s t

Fuses

Checking and Replacing
Fuses
If something electrical in your car
stops working, the first thing you
should check for is a blown fuse.
Determine from the chart on the
fuse box cover or inside the fuse
box which fuse or fuses control
that component. Check those fuses
first, but check all the fuses before deciding that is not the cause.
Replace any blown fuses and check
the component's operation.
1. Turn the ignition switch to LOCK (0). Make sure the head-
lights and all other accessories
are
off.

2. Remove the cover from the fuse box. 3. Check each of the large fuses in
the underhood fuse box by
looking through the top at the
wire inside. Removing these
fuses requires a phillips-head
screwdriver. 4. Check the smaller fuses in the
underhood fuse box and all the
fuses in the interior fuse box bypulling out each fuse with the
fuse puller provided in the interior fuse box.

Taking Care of the Unexpected
BLOWN
FUSE PULLERProCarManuals.comMain Menu Table of Contents s t

Four Wheel Steering

The Si 4WS model in the U. S and
the SR 4WS model in Canada are
equipped with an electronic Four
Wheel Steering system.
As inputs, the 4WS system uses a
vehicle speed sensor and a sensor to measure how far the front
wheels are turned.
The electronic control unit for 4WS system uses these inputs to deter-
mine which direction to steer the
rear wheels, and at what angle. Depending on vehicle speed and the
angle of the front wheels, the rear
wheels will be "countersteered"
(steered in the opposite direction of
the front wheels) or "same-steered"
(steered in the same direction as
the front wheels). The 4WS electronic control unit
drives an electric motor built into
the rear steering box. Sensors for
rear wheel angle and speed provide
feedback. The electronic control
unit uses this feedback to compare
the actual rear wheel angle to the
desired angle.
When the driver turns the front
wheels with the car traveling less
than 18 mph (30 km/h), the rear
wheels are countersteered. The angle of countersteer increases as
the angle of the front wheels in-
creases, to a maximum counter-
steer angle of six degrees. This
improves response when parallel
parking or making sharp turns.
Above 18 mph (30 km/h), the rear
wheels are same-steered as the driver begins to turn the steering
wheel. The rear wheel angle for
any given steering wheel angle is
not fixed; it increases as vehicle speed increases. This improves
response in lane-changing maneu-
vers.
As the driver continues to turn the
steering wheel, the rear wheels are
steered back to the straight-ahead
position and then to countersteer
mode. As with same steer, the
angle of countersteer varies with
vehicle speed; increasing and then decreasing as the speed rises. This
gives improved handling in low, medium, and high speed curves.
The 4WS system's electronic
control unit monitors the sensors
whenever the ignition is ON. If it detects a problem anywhere in the
system, it lights the 4WS indicator
on the instrument panel and turns
the system off. With the system off,
the rear wheels remain pointed
straight ahead. Your car will then
drive like a conventional car
without 4WS.

Technical InformationProCarManuals.comMain Menu Table of Contents s t