lights HONDA PRELUDE 1992 Owner's Manual

Preparing to Drive
You should do the following checks and adjustments every day before
you drive your car.
1. Make sure all windows, mirrors, and outside lights are clean and
unobstructed. Remove frost,
snow, or ice.
2. Check that the hood and trunk are fully closed.
3. Check that any items you may be carrying with you inside are
stored properly or fastened down
securely. 4. Check the adjustment of the seat
(see page 51 ).
5. Check the adjustment of the
inside and outside mirrors (see
page 59 ).

6. Chec k
the adjustment of the
steering wheel (see page 43 ).
7. Make sure the doors are securely
closed and locked.

8. Fasten your seat belt. Check that your passengers have fastened
their seat belts (see page 7 ). 9. Turn the ignition ON (II). Check

the indicator lights in the instru-
ment panel.

10.Start th
e
engine.
11.Check the gauges and indicator

lights in the instrument panel
(see page 31 ).

Driving
ProCarManuals.comMain Menu Table of Contents s t

The Braking System

Your Honda is equipped with disc brakes at all four wheels. The
braking system is power-assisted to
reduce the effort needed on the
brake pedal.
Put your foot on the brake pedal
only when you intend to brake.
Resting your foot on the pedal
keeps the brakes applied lightly,
causing them to build up heat. Heat
build-up can reduce how well your
brakes work. It also keeps your
brake lights on all the time, confusing drivers behind you.
Constant application of the brakes
when going down a long hill builds
up heat and reduces their effective-
ness. Use the engine to assist the
brakes by downshifting to a lower
gear and taking your foot off the
accelerator pedal. Check your brakes after driving
through deep water. Apply the
brakes moderately to see if they feel normal. If not, apply them
gently and frequently until they do. Since a longer distance is needed to
stop with wet brakes, be extra
cautious and alert in your driving.

Brake Wear Indicators

All four brakes have audible brake
wear indicators. When the brake pads need re-placing, you will hear a distinctive
metallic "screeching" sound when
you apply the brakes. If you do not
have the brake pads replaced, they
will begin screeching all the time.
Your brakes may sometimes squeal
or squeak when you apply them
lightly. Do not confuse this with the
brake wear indicators. They make a very audible "screeching".
Brake System Design

The hydraulic system that operates
the brakes has two separate cir- cuits. Each circuit works diago-
nally across the car (the left-front
brake is connected with the right-
rear brake, etc.). If one circuit
should develop a problem, you will
still have braking at two wheels.

Driving
FrontProCarManuals.comMain Menu Table of Contents s t

Driving in Bad Weather

Driving Technique — Always
drive slower than you would in dry
weather. It takes your car longer to react, even in conditions that may
seem just barely damp. Apply
smooth, even pressure to all the
controls. Abrupt steering wheel
movements or sudden, hard appli-
cation of the brakes can cause loss
of control in wet weather. Be extra
cautious for the first few miles of
driving while you adjust to the change in driving conditions. This
is especially true in snow. A person
can forget some snow-driving tech- niques during the summer months.
Practice is needed to relearn those

skills.

Exercise extra caution when
driving in rain after a long dry spell.
After months of dry weather, the
first rains bring oil to the surface of
the roadway, making it slippery. Visibility — Being able to see
clearly in all directions and being
visible to other drivers are impor-
tant in all weather conditions. This is more difficult in bad weather. To
be seen more clearly during day-
light hours, turn on your headlights.
Inspect your windshield wipers and
washers frequently. Keep the wind- shield washer reservoir full of the

proper fluid. Replace the wind-

shield wiper blades if they start to
streak the windshield or leave parts
unwiped. Use the defrosters and air conditioner to keep the windows
from fogging up on the inside (see
page 73).
Traction — Check your tires
frequently for wear and proper pressure. Both are important in
preventing "hydroplaning" (loss of
traction on a wet surface). In the
winter, mount snow tires on all four
wheels for the best handling.
Watch road conditions carefully, they can change from moment to
moment. Wet leaves can be as slip-
pery as ice. "Clear" roads can have
patches of ice. Driving conditions
can be very hazardous when the
outside temperature is near freez-
ing. The road surface can become
covered with areas of water pud-
dles mixed with areas of ice, so
your traction can change without

warning.

Be careful when downshifting. If
traction is low, you can lock up the
drive wheels for a moment and
cause a skid.

DrivingProCarManuals.comMain Menu Table of Contents s t

Towing a Trailer

Mirrors
Many states and provinces have
laws requiring special outsidemirrors when you are towing a
trailer. Check the laws in your area.
You may want to install mirrors, even if they are not required. Hook
up the trailer and see how much it obscures your ability to see behind
you with the standard mirrors. Ifyou cannot see directly behind you,
or have a large blind spot next to
the trailer or the car, you should
install mirrors intended for towing.
Connecting the Trailer

Most trailers that have a gross
weight of 450 kg (1,000 Ibs) do not
have their own braking system. If you are thinking of getting a trailer
that does have brakes, make sure
they are electrically-operated.
There are no provisions in your car
to tap into its hydraulic braking
system. Any attempt to attach the
trailer's brakes to your car's
hydraulic system, no matter how successful it may seem, will lower
braking effectiveness and create a potential hazard.
Always use a safety chain when towing a trailer. Connect the safety
chain securely at both ends. Make
sure the chain crosses under the
tongue so it will catch the trailer if
it becomes unhitched. Leave
enough slack in the chain so it can't
bind in a sharp turn. Do not let it drag on the ground.
Before Starting Out

As you are preparing to tow your
trailer, do the following:
Measure the trailer's tongue load.
You can do this with a bathroom

scale.

Verify that the hitch and safety chain are securely fastened.
Check the condition and air
pressure of all tires on the trailer
and your car. Low tire pressure
can seriously affect the handling.
Also check the spare tires.
With everything loaded and the
trailer connected, check that the
rear of the car is not sagging. If
so, redistribute the load in the
car.
Check that all lights on the car
are working properly.

DrivingProCarManuals.comMain Menu Table of Contents s t

Maintenance

Regularly maintaining your Honda
is the best way to protect your investment. You will be rewarded
with safer, more economical,
trouble-free driving. This section
lists items that need to be checked
regularly and explains how to check them. It also details some
simple maintenance tasks you can

do yourself. The maintenance

schedules for normal and severe
driving conditions show you when
these things need to be done.
If you are interested in how to per-
form more complex maintenance
on your Honda, you can purchase
the Service Manual. See page 221 for information on how to
obtain a copy, or see your Honda

dealer.
Maintenance Schedule................ 128
Maintenance Record................ 131
Periodic Checks............................ 133
Fluid Locations............................. 134

Engine Oil...................................... 135
Checking Engine Oil................ 135

Adding........................................ 135
Recommended Oil.................... 136

Additives.................................... 136 Oil and Filter Changes ............ 137
Cooling System............................. 139 Checking the Coolant Level... 139
Adding Radiator Coolant........ 139
Replacing Coolant.................... 140
Windshield Washers.................... 143

Transmission Oil.......................... 144
Automatic Transmission........ 144
5-speed Transmission.............. 145

Brake and Clutch Fluid............... 146
Brake System............................ 146
Anti-lock Brake System ......... 147 Clutch System........................... 147
Power Steering............................. 148

Air Filter....................................... 149
Fuel Filter..................................... 150

Spark Plugs.................................. .
150
Replacement.............................. 150
Specification.............................. 152
Battery............................................ 152
Windshield Wipers....................... 155
Air Conditioner............................. 157 Engine Belts.................................. 158
Tires................................................ 158 Inflation...................................... 158
Inspection................................... 159
Maintenance.............................. 160
Tire Rotation............................ 160
Replacing Tires ........................ 161
Wheels and Tires...................... 161
DOT Tire Quality Grading..... 161 Treadwear............................. 161
Traction................................. 162
Temperature......................... 162
Winter Driving.......................... 163 Snow Tires............................ 163
Tire Chains............................ 163
Lights.............................................. 164
Replacing Bulbs........................ 164
Storing Your Car.......................... 173

MaintenanceProCarManuals.comMain Menu s t

Periodic Checks

You should check the following items at the specified intervals. If
you are unsure of how to perform
any check, turn to the page given. Engine oil level — Check every
time you fill the gas tank. See
page 102.

Engine coolant level — Check

the radiator reserve tank every
time you fill the gas tank. See

page 103.

Windshield washer fluid —
Check the level in the reservoir
monthly. If weather conditions
cause you to use the washers
frequently, check the reservoir each time you stop for gas. See

page 143 .

Automatic transmission — Check the fluid level monthly.
See page 144. Brakes, clutch and power
steering — Check the fluid level
monthly. See page 146.Tires — Check the tire pressure
monthly. Examine the tread for
wear and foreign objects. See
page 159.
Battery — Check its condition
and the terminals for corrosion
monthly. See page 152.
Air conditioner — Check its operation weekly. See page 157.
Lights — Check the operation of
the headlights, parking lights,
taillights, high-mount brake light,
turn signals, brake lights, and
license plate lights monthly. See
page 164.

MaintenanceProCarManuals.comMain Menu Table of Contents s t

Lights

Check the operation of your car's
exterior lights at least once a
month. A burned out bulb can
create an unsafe condition by
reducing your car's visibility and
the ability to signal your intentions
to other drivers. Check the following:
Headlights (low and high beam) Parking lights
Taillights
Brake lights
High-mount brake light
Turn signals Back-up lights
Hazard light function
License plate light
Side marker lights
Daytime running lights
(Canadian cars)

If you find any
bulbs are burned
out, replace them as soon as
possible. Refer to the chart on page
207 to determine what

type of
replacement bulb is needed.
Replacing a Headligh
t Bulb

Your car has two bulbs on each

side, four in total. Make sure you

are replacing the bulb that is

burned out. Your car uses halogen

headlight bulbs. When replacing a

bulb, handle it by its plastic case
and protect the glass from contact

with your skin or hard objects. If
you touch the glass, clean it with

denatured alcohol and a clean cloth.

Halogen headlight bulbs get very

hot when lit. Oil, perspiration, or a

scratch on the glass can cause the

bulb to overheat and shatter.
1. Open the hood.

If you need to change the high

beam headlight bulb
on
the

passenger's side, remove the

radiator reserve tank by pulling
it straight up.
2. To disconnect the bulb from the
electrical harness, push on the

end of the lock tab to release the
connector then push the connec-
tor straight down.
Maintenance
NOTICEProCarManuals.comMain Menu Table of Contents s t

Lights

3. Turn the lock ring counterclock-
wise (about one-quarter turn) to unlock the headlight bulb.

4. Remove
the bulb by pulling it

straight out of its recess.

5. Install

the new bulb with the
electrical connector pointing
down. Make sure all three tabs on the bulb are seated in their
slots in the headlight.
6. Turn the lock ring clockwise to

lock the bulb in place. Do not
force the ring. Check the seating

of th e
bulb's tabs if the ring will
not return to its original position.
7. Reinstall the harness connector on the bulb connector. Make sure

it locks in place.

Turn o n
the headlights to test

the new bulb.

8. (Passenger'
s
side)

Reinstall the radiator reserve
tank.

Replacing a
Parkin
g Light
Bulb

1. Use a phillips head screwdriver

to remove the screw from the top
of the fender.

2. Mov e
the parking light assembly

forward until it slides out of the
body.

3. Tur n
the socket one-quarter turn

counterclockwise to remove it
from the lens.

CONTINUED

Maintenance

SCREW
ProCarManuals.comMain Menu Table of Contents s t

Lights
4. Pull the bulb straight out of its
socket.

Push the
new bulb straight into
the socket until it bottoms
.
5. Insert
the socket back into the

lens. Turn it clockwise to lock it
in place.

6. Turn

on the parking lights to

make sure the new bulb works.

7. To

reinstall the light assembly in

the fender, line up the fingers on
the light assembly with the holes
in the fender. Push the light
assembly straight back.

8. Instal
l
the mounting screw and

tighten it securely.

Replacing a

Front Side
Marker Light Bulb

1. Use a phillips-head screwdriver to loosen the side marker assem-
bly's mounting screw.
2. Remove the side marker assem- bly from the bumper. 3. Remove the bulb holder from the
side marker assembly by turning
it one-quarter counterclockwise.
4. Pull the bulb straight out of its socket.
Push the new bulb straight into
the socket until it bottoms.

Maintenance
SCREW

BULB HOLDER
BULB

FRONT SIDE
MARKER
ASSEMBLYProCarManuals.comMain Menu Table of Contents s t

Lights
5. Push the bulb holder into the side marker assembly and turn it
clockwise until it locks.
6. Test the side marker to make sure the new bulb is working.
7. Put the side marker assembly into the bumper. Make sure the
tab on the side marker assembly
fits into the bumper slot. Tighten
the mounting screw.
Replacing a Front Turn
Signal Light Bulb

1. Use a phillips-head screwdriver to loosen the turn signal assem-
bly's mounting screw.
2. Remove the turn signal assembly from the bumper. 3. Remove the bulb holder from the
turn signal assembly by turning
it counterclockwise.
4. Remove the burned out bulb from the socket by pushing it in
and turning counterclockwise
until it unlocks.Install the new bulb.

Maintenance

SCREW
TURN SIGNAL ASSEMBLY

BULB
BULB HOLDER

CONTINUEDProCarManuals.comMain Menu Table of Contents s t