light HUMMER H3 2009 Owner's Manual

Full-Time Four-Wheel
Drive
Full-Time Four-Wheel Drive sends
engine power to all four wheels
for extra traction. To get the most
out of Full-Time Four-Wheel Drive,
you must be familiar with its
operation.
Transfer Case Buttons
The transfer case buttons are
located to the right of the instrument
panel cluster. Use these switches to
shift into and out of the different
Full-Time Four-Wheel Drive modes.4
m(Four-Wheel High):This
setting is used for driving in most
street and highway situations.
You can also use this setting for
light or variable off-road conditions.
N (Neutral):Shift the transfer
case to Neutral only when towing
the vehicle. SeeRecreational
Vehicle Towing on page 4-40or
Towing Your Vehicle on page 4-40
for more information.
Notice:Driving on pavement in
Four-Wheel High Lock or Four
Wheel Low Lock for extended
periods may cause premature
wear on the vehicle powertrain
and tires. Do not drive in
Four-Wheel High Lock or
Four-Wheel Low Lock on
pavement for extended periods.
4
mQ(Four-Wheel-High Lock):
Use this setting when you need
extra traction in most off-road
situations such as sand, mud, snow
or level, rocky trails.Notice:Operating the vehicle in
Four-Wheel-Low Lock above
30 mph (48 km/h) for any
extended period of time could
cause damage to the transfer
case. Do not operate the vehicle
in Four-Wheel-Low Lock above
30 mph (48 km/h) for extended
periods.
4
nQ(Four-Wheel-Low Lock):
This setting delivers extra torque to
all four wheels and is used for
extreme off-road conditions.
If the vehicle has locking axles,
they can be locked for additional
traction in extreme off-road
situations. SeeLocking Rear Axle
on page 4-8andLocking Front Axle
on page 4-9.
Indicator lights in the buttons show
which setting the transfer case
is in. The indicator lights will come
on briey when the ignition is in
ON/RUN. The If the lights do
not come on, take the vehicle to
your dealer/retailer for service.
2-24 Features and Controls

An indicator light will ash while
shifting the transfer case. If the
transfer case cannot make a
requested shift, it will return to the
last chosen setting.
If the SERV 4WD message on the
Driver Information Center (DIC)
stays on, take the vehicle to
your dealer/retailer for service.
See Service 4WD message under
DIC Warnings and Messages
on page 3-37.
Shifting between Four-Wheel
High and Four-Wheel-High Lock
With the vehicle traveling less
than 75 mph (120 km/h), press and
release the Four-Wheel High or
Four-Wheel-High Lock button.
It may be necessary to drive
backwards while turning for a
distance of 25 feet (7.5 m) to get
the lock feature to disengage.Shifting into Four-Wheel Low Lock
Notice:Shifting the transmission
into gear before the indicator
light stops ashing could cause
damage to the transfer case.
Always wait until the indicator
light stops ashing before putting
the transmission back in gear.
To shift into Four-Wheel-Low Lock,
the ignition must be in ON/RUN
and the vehicle must be stopped or
moving less than 3 mph (5 km/h)
with the transmission in N (Neutral).
The preferred method for shifting
into Four-Wheel Low is to have
the vehicle moving 1 to 2 mph
(1.6 to 3.2 km/h). Press and release
the Four-Wheel-Low Lock button.
If the vehicle has a manual
transmission, the clutch pedal must
be pressed to the oor while you
press the Four-Wheel-Low Lock
button, or the shift will not be
completed. You must wait for theFour-Wheel-Low Lock indicator
light to stop ashing and remain lit
before shifting the transmission
into gear.
It is normal for the vehicle to have
engagement noise and bump
when shifting between Four-Wheel
Low and Four-Wheel High ranges
or from Neutral.
If the Four-Wheel-Low Lock button
is pressed when the vehicle is
in gear and/or moving too fast, the
Four-Wheel-Low Lock indicator
light will ash for 15 seconds and
not complete the shift.
Features and Controls 2-25

Shifting Out of
Four-Wheel-Low Lock
Notice:Shifting the transmission
into gear before the indicator
light stops ashing could cause
damage to the transfer case.
Always wait until the indicator
light stops ashing before putting
the transmission back in gear.
To shift out of Four-Wheel-Low Lock,
the vehicle must be stopped or
moving less than 3 mph (5 km/h)
with the transmission in N (Neutral)
and the ignition in ON/RUN.
The preferred method for shifting out
of Four-Wheel-Low Lock is to have
the vehicle moving 1 to 2 mph
(1.6 to 3.2 km/h). Press and
release the Four-Wheel High or
Four-Wheel-High Lock button.If the vehicle has a manual
transmission, the clutch pedal must
be pressed to the oor while you
press the Four-Wheel High or
Four-Wheel-High Lock button, or the
shift will not be completed. You must
wait for the Four-Wheel High or
Four-Wheel-High Lock indicator light
to stop ashing and remain lit before
shifting the transmission into gear.
It is normal for the vehicle to have
engagement noise and bump
when shifting between Four-Wheel
Low and Four-Wheel High ranges
or from Neutral.
If the Four-Wheel High or
Four-Wheel-High Lock button is
pressed when the vehicle is in
gear and/or moving too fast,
the Four-Wheel High or
Four-Wheel-High Lock indicator
light will ash for 15 seconds but
will not complete the shift.Shifting Into Neutral
To shift the transfer case to Neutral:
1. Set the parking brake.
2. Start the vehicle.
3. Put the transmission in
N (Neutral). If the vehicle has a
manual transmission, press and
hold the clutch pedal down while
you perform Steps 5 through 9.
4. Shift the transfer case to
Four-Wheel High.
{CAUTION
Shifting an all-wheel-drive
vehicle’s transfer case into
Neutral can cause the vehicle
to roll even if the automatic
transmission is in P (Park) or the
manual transmission is in any
gear. You or others could be
injured. Make sure the parking
brake is rmly set before you shift
the transfer case to Neutral.
2-26 Features and Controls

5. Simultaneously press and hold
the Four-Wheel High and
Four-Wheel-Low Lock buttons for
10 seconds. The Neutral light
will come on when the transfer
case shift to Neutral is complete.
6. Press and hold the regular brake
pedal and shift the transmission
to R (Reverse), then shift the
transmission to D (Drive) for an
automatic transmission, or
1 (First) for vehicles have a
manual transmission and then let
out the clutch. This is to ensure
the transfer case is in Neutral.
If not, repeat this procedure
starting at Step 3.
7. Turn the engine off.
8. Place the transmission shift lever
in P (Park) for an automatic
transmission, or 1 (First) for
vehicles that have a manual
transmission.
9. Turn the ignition to LOCK/OFF.Shifting Out of Neutral
To shift out of Neutral:
1. Set the parking brake and apply
the regular brake pedal.
2. Shift the transmission to
N (Neutral) for an automatic
transmission, or press the clutch
pedal for vehicles that have a
manual transmission. Then turn
the ignition to ON/RUN but
do not start the engine.
3. Press the button for the desired
transfer case shift position
(Four-Wheel High,
Four-Wheel-High Lock or
Four-Wheel-Low Lock).
After the transfer case has
shifted out of Neutral the light
will go out.
4. Release the parking brake.Notice:Shifting the transmission
into gear before the indicator
light stops ashing could cause
damage to the transfer case.
Always wait until the indicator
light stops ashing before putting
the transmission back in gear.
5. You may start the engine and
shift the transmission to the
desired position.
Features and Controls 2-27

Parking Brake
The parking brake pedal is located
to the left of the regular brake
pedal, near the driver door.
To set the parking brake, hold the
regular brake pedal down, then push
the parking brake pedal down to
its fully-applied position.A chime will sound and the brake
warning light will ash when the
parking brake is applied and
the vehicle is moving at least 3 mph
(5 km/h) for at least three seconds.
SeeBrake System Warning Light
on page 3-27.
To release the parking brake, hold
the regular brake pedal down. Pull
the park brake release lever, located
above the parking brake pedal.Notice:Driving with the parking
brake on can overheat the
brake system and cause
premature wear or damage to
brake system parts. Make
sure that the parking brake is
fully released and the brake
warning light is off before driving.
If you are towing a trailer and are
parking on a hill, seeTowing a
Trailer on page 4-42.
2-28 Features and Controls

Mirrors
Automatic Dimming
Rearview Mirror
The vehicle has an automatic
dimming rearview mirror with a
compass and temperature display.
Vehicles with OnStar
®have
three additional control buttons for
the OnStar
®system. See your
dealer/retailer for more information
about OnStar
®and how to
subscribe to it. SeeOnStar®
System on page 2-39for more
information about the services
OnStar
®provides.
z(On/Off):Press to turn the
dimming feature on or off.
The vehicle may also have a Rear
Vision Camera (RVC). SeeRear
Vision Camera (RVC) on page 2-36
for more information.
Automatic Dimming Mirror
Operation
Automatic dimming reduces the
glare from the headlamps of
the vehicle behind you. The dimming
feature comes on and the indicator
light illuminates each time the
ignition is turned to start.
Temperature Display
To adjust between Fahrenheit and
Celsius:
Presszfor approximately
four seconds to toggle the display
from F (Fahrenheit) to C (Celsius)
to OFF. Release the button after
the display has toggled to the
next state.
The temperature display will
remain in its current state each
time the ignition goes through
its cycle.
At start up, if the vehicle has been
off for less than two and a half
hours, and the last stored
temperature was less than the
current temperature, the sensor
will increase 1°F every
two minutes until the correct
temperature is displayed.
If the vehicle has been off more
than two and a half hours, or the
last stored temperature is greater
than the current temperature, the
current temperature immediately
displays.
If the temperature is 37°F (3°C) or
lower, ICE will ash on the
temperature display. This display
will ash every two seconds for a
period of one minute.
If an abnormal temperature reading
is displayed for an extended
period of time, see your
dealer/retailer. Under certain
circumstances, a delay in updating
the temperature is normal.
Features and Controls 2-33

Object Detection
Systems
Rear Vision
Camera (RVC)
Vehicles with the rear vision camera
system are designed to help the
driver while the vehicle is backing
up. The area behind the vehicle
is displayed on the screen in the
inside rear view mirror. Read this
entire section before using the
camera system.
When the key is in the ON/RUN
position and the driver shifts the
vehicle into R (Reverse), the video
image appears from inside the
rear view mirror. Once the vehicle
is shifted out of R (Reverse),
the image disappears.
The display may have a guideline
overlay that can help the driver align
the vehicle when backing into a
parking spot.Turning the Rear Vision Camera
System On or Off
To turn off the rear vision camera
system, press and hold
z, located
on the inside rearview mirror,
until the left indicator light turns off.
The rear camera vision display
is now disabled.
To turn the rear vision camera
system on again, press and
hold
zuntil the left indicator light
illuminates. The rear vision
camera system display is now
enabled and the display will appear
in the mirror normally.
{CAUTION
The Rear Vision Camera (RVC)
system does not replace driver
vision. RVC does not:
Detect objects that are
outside the camera’s eld of
view, below the bumper, or
underneath the vehicle.
Detect children, pedestrians,
bicyclists, or pets.
Do not back the vehicle by only
looking at the rear vision camera
screen, or use the screen during
longer, higher speed backing
maneuvers or where there could
be cross-traffic. Your judged
distances using the screen will
differ from actual distances.
(Continued)
2-36 Features and Controls

When the System Does Not Seem
To Work Properly
The rear vision camera system may
not work properly or display a
clear image:
In the dark.
When the sun or the beam of
headlamps is shining directly
into the camera lens.
If ice, snow, mud, or anything else
builds up on the camera lens.
Clean the lens, rinse it with water,
and wipe it with a soft cloth.
If the back of the vehicle is in an
accident, the position and
mounting angle of the camera
may change or the camera may
be affected. Be sure to have the
camera and its position and
mounting angle checked at your
dealer/retailer.
If there are extreme temperatures
or extreme temperature changes.The rear vision camera system
display in the rearview mirror may
turn off or not appear as expected
due to a loss of video signal, or
no video signal present during the
reverse cycle. The display will
be blank and the left indicator light
will slowly ash as long as the
vehicle is in R (Reverse) or until the
condition returns to normal.
Pressing and holding
zwhen the
left indicator light is ashing will
turn off the video display along with
the left indicator light.
OnStar®System
OnStar uses several innovative
technologies and live advisors to
provide a wide range of safety,
security, information, and
convenience services. If the airbags
deploy, the system is designed to
make an automatic call to OnStar
Emergency advisors who can
request emergency services be sent
to your location. If the keys are
locked in the vehicle, call OnStar
at 1-888-4-ONSTAR to have a
signal sent to unlock the doors.
OnStar Hands-Free Calling,
including 30 trial minutes good for
60 days, is available on most
vehicles. OnStar Turn-by-Turn
Navigation service, with one trial
route, is available on most vehicles.
Press the OnStar button to have
an OnStar advisor contact Roadside
Service.
Features and Controls 2-39

OnStar service cannot work unless
the vehicle is in a place where
OnStar has an agreement with a
wireless service provider for service
in that area. OnStar service also
cannot work unless the vehicle is in
a place where the wireless service
provider OnStar has hired for
that area has coverage, network
capacity and reception when
the service is needed, and
technology that is compatible
with the OnStar service. Not all
services are available everywhere,
particularly in remote or enclosed
areas, or at all times.
Location information about the
vehicle is only available if the GPS
satellite signals are unobstructed
and available.
The vehicle must have a working
electrical system, including adequate
battery power, for the OnStar
equipment to operate. There are
other problems OnStar cannotcontrol that may prevent OnStar
from providing OnStar service at
any particular time or place.
Some examples are damage to
important parts of the vehicle in a
crash, hills, tall buildings, tunnels,
weather or wireless phone network
congestion.
Your Responsibility
Increase the volume of the radio
if the OnStar advisor cannot
be heard. If the light next to the
OnStar buttons is red, the system
may not be functioning properly.
Press the OnStar button and request
a vehicle diagnostic. If the light
appears clear (no light is appearing),
your OnStar subscription has
expired and all services have been
deactivated. Press the OnStar
button to conrm that the OnStar
equipment is active.Universal Home
Remote System
The Universal Home Remote
System provides a way to
replace up to three hand-held
radio-frequency (RF) transmitters
used to activate devices such
as garage door openers, security
systems, and home lighting.
This device complies with Part 15
of the FCC Rules. Operation is
subject to the following two
conditions:
1. This device may not cause
harmful interference.
2. This device must accept any
interference received, including
interference that may cause
undesired operation.
The FCC Grant of Equipment
Authorization Certicate number
is CB2SAHL3.
2-42 Features and Controls

This device complies with RSS-210
of Industry Canada. Operation is
subject to the following two
conditions:
1. This device may not cause
interference.
2. This device must accept any
interference received, including
interference that may cause
undesired operation of the
device.
The Canadian Registration
ID number is 2791021849A.
Changes or modications to this
system by other than an authorized
service facility could void
authorization to use this equipment.Universal Home Remote
System Operation
If there is one triangular Light
Emitting Diode (LED) indicator
light above the Universal Home
Remote buttons, follow the
instructions below.
This system provides a way to
replace up to three remote control
transmitters used to activate devices
such as garage door openers,
security systems, and home
automation devices.Do not use the Universal Home
Remote with any garage door
opener that does not have the stop
and reverse feature. This includes
any garage door opener model
manufactured before April 1, 1982.
Read the instructions completely
before attempting to program
the Universal Home Remote.
Because of the steps involved,
it may be helpful to have another
person available to assist you in
the programming the Universal
Home Remote.
Keep the original hand-held
transmitter for use in other vehicles
as well as for future Universal
Home Remote programming.
It is also recommended that
upon the sale of the vehicle, the
programmed Universal Home
Remote buttons should be erased
for security purposes. See “Erasing
Universal Home Remote Buttons”
later in this section.
Features and Controls 2-43