seats Hyundai Accent 2006 Owner's Guide

1FEATURES OF YOUR HYUNDAI
30
B230D04E-GAT Using a Child Restraint System with "ISOFIX" System and"Tether Anchorage" System ISOFIX is a standardised method of fitting child seats that eliminates the need to use the standard adult seat beltto secure the seat in the vehicle. This enables a much more secure and posi- tive location with the added benefit ofeasier and quicker installation. An ISOFIX-seat can only be installed if it has vehicle-specific approval in ac- cordance with the requirements of ECE- R44. For your Hyundai, the HyundaiISOFIX GR1 / Hyundai Duo / Römer
B230D01A ISOFIX GR1 and the Römer Duo ISOFIX / Britax Duo ISOFIX is approved ac-cording to the requirement ECE-R44. This seat has been tested extensively by Hyundai and is recommended foryour Hyundai. NOTE: At present, this seat is the only one complying with that provision. Incase that other manufacturers will furnish proof of a respective certifi- cation, Hyundai is going to evaluatethis seat carefully and will give a recommendation provided that seat complies to the law. Please ask yourHyundai dealer in this respect.
B230D02A-E
ISOFIX Anchor
ISOFIX Anchor Position Indicator
B230E03A
Front of Vehicle
Back Panel Load Space Cover
2. Remove the load space cover.
3. Connect the tether strap hook to the child restraint hook holder and tighten to secure the seat.
Tether Strap Hook

1FEATURES OF YOUR HYUNDAI
32
!
U : Suitable for "universal" category
restraints approved for use in this mass group
UF: Suitable for forward-facing "univer- sal" category restraints approvedfor use in this mass group
L1 : Suitable for "Römer ISOFIX GR1" approved for use in this mass group(Approval No: E1 R44-03301133)
X : Seat position not suitable for chil- dren in this mass group Ordinarily the pre-tensioner seat beltoperates in the same way as E.L.R(Emergency Locking Retractor) type (When the vehicle stops suddenly, or if the occupant tries to lean forward tooquickly, the seat belt retractor will lock into position.). However, when vehicles crash, the retractor rewinds the beltwebbing. This will restrain the passen- ger movement quickly and also reduce the slack between passenger and beltwebbing. NOTE:
o When the pre-tensioner seat belt
is activated, there may be an ex- plosion noise. This noise is nor-mal and is not hazardous.
o Pre-tensioner seat belt is designed
to operate only when a sufficientlysevere impact occurs and it will be only operated once.
B180C01A-GAT Pre-tensioner Seat Belt (Without A/BAG) (If Installed) WARNING:
If the pre-tensioner seat belt was activated, never attempt to replace itby yourself. It must be replaced by an authorized Hyundai Dealer.
B230H04A-GAT Child Seat Restraint Suitability For Seat Position Use child safety seats that have been officially approved and are appropriate for your children. When using the child safety seats, refer to the following table. or tabs may allow the child to reach the unretracted seat belts which may result in strangulationand a serious injury or death to the
child in the child restraint.o D o not mount more than one childrestraint to a child restraint lower anchorage point. The improper increased load may cause the an-chorage points or tether anchor to break, causing serious injury or death.
o Attach the ISOFIX or ISOFIX-com- patible child restraint seat only tothe appropriate locations shownin the illustration.
o Always follow the installation and
use instructions provided by themanufacturer of the child restraint. Rear
Center
Age Group Seating Position
UX
X UX
Rear
Outboard
Front
Passenger
0 : Up to 10 kg (0 ~ 9 months)0+ : Up to 13 kg(0 ~ 2 years)I : 9kg to 18kg(9 months ~ 4years)II & III : 15kg to36kg (4 ~ 12 years) X
X U, L1 U F XU
FUF

1
FEATURES OF YOUR HYUNDAI
41DUAL-STAGE SUPPLEMENTAL RESTRAINT (AIRBAG) SYSTEM
B240A01A-AAT (If Installed)
Your Hyundai is equipped with a Dual- stage Supplemental Restraint (Airbag) System. The indications of the system's presence are the letters "SRS AIRBAG"embossed on the airbag pad cover in the steering wheel and the passenger's side front panel pad above the glovebox. The Hyundai SRS consists of airbags installed under the pad covers in the center of the steering wheel and thepassenger's side front panel above the glove box. The purpose of the SRS is to provide the vehicle's driver and/or thefront passenger with additional protec- B240A03A
Driver's Airbag
!WARNING:
o As its name implies, the SRS is designed to work with, and be supplemental to, the driver's and the passenger's three point seatbelt systems and is not a substi- tute for them. Therefore, your seat belts must be worn at all timeswhile the vehicle is in motion. The airbags deploy only in certain fron- tal impact conditions severeenough to cause significant injury to the vehicle occupants.
NOTE:
o Be sure to read information about
the SRS on the labels provided on the backside of the sun visor andin the glove box.
o Dual-stage inflating airbags are
combined with pre-tensioner seatbelts to help provided enhanced occupant protection in frontal crashes. Front airbags are not in-tended to deploy in light colli- sions in which protection can be provided by the pre-tensioner seatbelt.
tion than that offered by the seat-beltsystem alone, in case of a frontal im-pact of sufficient severity. The Dual-stage SRS uses a collection of sensors to gather information about the driver's and front passenger's seatposition, the driver's and front passenger's seat belt usage and im- pact severity.The driver's and front passenger's seat position sensors determine if the seats are fore or aft of a reference position.Similarly, the seat belt usage sensors determine if the driver and front passenger's seat belts are fastened.These sensors provide the ability to control the SRS deployment's pressure based on how close the driver's seat isto the steering wheel, how close the passenger's seat is to the instrument panel and whether or not the seat beltsare fastened. The dual-stage airbags offer the ability to control the airbag inflation with two pressure levels. A lower pressure levelis provided for moderate-severity im- pacts. A higher-pressure level is pro- vided for more severe impacts.

1
FEATURES OF YOUR HYUNDAI
75SEAT POCKETMULTI BOX
B540B01TB-AAT (If Installed) A seat side pocket is located on the front passenger seat to hold papers. There are seatback pockets on the backside of the front seats.
B500B01A-GAT (Left-hand Drive type only) (If Installed) The multi box is opened by turning the knob clockwise.To close the multi box, push it and turn the knob counterclockwise.
HLC2119
B500B01A
B510A01A-AAT Manual Type (If Installed) The outside rearview mirrors are equipped with a remote control for your convenience. It is operated by the con-trol lever in the bottom front corner of the window. Before driving away, always check thatyour mirrors are positioned so you can see behind you, both to the left and right sides, as well as directly behind yourvehicle. When using the mirror, always exercise caution when attempting to judge the distance of vehicles behind oralong side of you.
HLC2113
OUTSIDE REARVIEW MIRROR

13
1
CONTROLS AND EQUIPMENT
!
B080B02FC-EAT FRONT SEATS Seat Rake Adjustment
HLC2026-D
The front seat rake adjustment is per- formed by raising the lever at the front of the seat base and sliding the seat tothe desired position. At this position the lever should be released and the seat rocked to and fro to ensure that themechanism has locked. SB070C1-E Seat Recline Adjustment The front seat back recline angle may be adjusted by leaning forward slightlyand raising the recline adjustment lever at the side of the seat. When the seatback is at the desired angle, thelever should be released. Ensure that the seatback is locked before driving the vehicle.
HLC2027-D
WARNING:
To ensure the seat is locked se-curely, attempt to move the seat for- ward or rearward without using the lever.
!WARNING:
To minimize risk of severe injury in the event of a collision or a sudden stop, both the driver and passenger seatbacks should always be in anupright position while the vehicle is in motion. The protection provided by the seat belts and airbags in afrontal collision may be reduced sig- nificantly when the seatbacks are reclined. There is greater risk thatthe driver and passenger will slide under the seat belt which may result in serious injury if a crash occurswhen the seatbacks are reclined. The seat belt cannot provide full protec- tion to an occupant if the seatback isreclined.

17
1
CONTROLS AND EQUIPMENT
For greater convenience, the seat backs may be folded down individually.
o To unlock the seatback, pull up the
seatback locking knob, then push forward on the seatback panel.
o When you return the seatback to its
upright position, always be sure it haslocked into position by pulling and pushing on the top of the seatback. B110A02A-E
carried on the folded-down seatback should not extend higher than thetop of the front seats. This could allow cargo to slide forward and cause injury or damage during sud-den stops.
B140A01A
B140A01S-AAT REAR SEAT WARNING
For the safety of all passengers, lug- gage or other cargo should not be piledhigher than the top of the seatback. In addition, do not place objects on the rear shelf as they may move forwardduring braking or in an accident and strike vehicle passengers.
!WARNING:
When you return the rear seatback to its upright position after being folded down, be careful not to damage the seat belt webbing or buckle. In addi-tion, do not allow the seat belt web- bing or buckle to get caught or pinched in the rear seat.

1CONTROLS AND EQUIPMENT
18
SB090E1-E Injured Persons A seat belt should be used when an injured person is being transported. Forspecific recommendations, the advice of a qualified Medical Practioner should be sought. SB090F1-E Seat Belt Occupancy The seat belts are designed to be used by one seat occupant only. The use of a seat belt by more than one person increases the levels of injury whichmay be sustained in the event of an accident. SE090G1-E Do Not Lie Down To ensure that the maximum level of protection may be afforded by the seat belt system, all passengers should besitting in an upright position throughout the journey. The seat belt will be unable to afford maximum protection if thefront seats are at or near the fully reclined position.
SB090C1-E Larger Children Larger children should occupy the rear seat and be restrained at all times. Therestraint may take the form of a special safety belt or the original factory fitted seat belt used in conjunction with anapproved booster cushion depending upon the size and weight of the child. Under no circumstances should chil-dren be allowed to travel standing, kneel- ing or lying on the seat. Never allow children to ride in the frontpassenger seat. SB090O1-E Pregnant Women The use of a seat belt is recommended for pregnant women. The seat belt should be worn as low and snugly as possible across the hips, not across the abdo-men. A qualified Medical Practitioner should be consulted for further informa- tion.SEAT BELT
SB090A1-E SEAT BELT PRECAUTIONS Seat belts should be worn at all times by all occupants front and rear. Thepossibility of injury or the severity of injuries suffered in the event of an accident will be greatly reduced by thewearing of seat belts. In addition the following recommenda- tions should be observed. SB090B1-E Babies/Small Children Babies and small children must be restrained using a restraint system spe-cifically designed for this purpose. Un- der no circumstances should a child be carried in the vehicle without the use ofa suitable restraint which meets the regulations in force in the country where the vehicle is in operation.

1CONTROLS AND EQUIPMENT
22CHILD RESTRAINT SYSTEM
B230A03A-EAT Children riding in the car should sit in the rear seat and must always be prop- erly restrained to minimize the risk of injury in an accident, sudden stop orsudden manoeuvre. According to acci- dent statistics, children are safer when properly restrained in the rear seatsthan in the front seat. Larger children should use one of the seat belts pro- vided.You are required by law to use safety restraints for children. If small children ride in your vehicle you must put themin a child restraint system (safety seat). Children could be injured or killed in a crash if their restraints are not properlysecured. For small children and babies, a child seat or infant seat must be used. Before buying a particular child restraintsystem, make sure it fits your car and seat belts, and fits your child. Follow all the instructions provided by the manu-facturer when installing the child re- straint system.
!
B220C01A-EAT To Release the Seat Belt
When you want to release the seat belt, press the button in the locking buckle. B220E01A
WARNING:
The centre belt latching mechanism is different from those for the rear seat shoulder belts. When fastening the rear seat shoulder belts or therear seat centre belt, make sure they are inserted into the correct buckles to obtain maximum protection fromthe seat belt system and assure proper operation.
!WARNING:
o When using the rear seat centre belt, you must lock all metal tabs and buckles. If any metal tab or buckle is not locked, it will in- crease the chance of injury in theevent of collision.
o Never unlock the metal tab (a) and
the buckle (b) with the followingexceptions.(1) In case of folding rear
seatbacks down.
(2) If transporting an object on the rear seat may cause damage tothe rear seat center belt.
o Lock the metal tab (a) and the buckle (b) immediately after fold-ing rear seatbacks up.

1CONTROLS AND EQUIPMENT
24
!
If you need to tighten the belt, pull more webbing toward the retractor. When youunbuckle the seat belt and allow it to retract, the retractor will automatically revert back to its normal seated pas-senger emergency locking usage con- dition. NOTE:
o Before installing the child restraint
system, read the instructions sup- plied by the child restraint system manufacturer.
o If the seat belt does not operate as described, have the systemchecked immediately by your au-thorized Hyundai dealer.
WARNING:
Do not install any child restraint sys-tem in the front passenger seat.Should an accident occur and cause the passenger side airbag to deploy, it could severely injure or kill aninfant or child seated in an infant or child seat. Therefore, only use a child restraint system in the rear seat ofyour vehicle.
To install a child restraint system in the outboard rear seats, extend the shoul- der/lap belt from its retractor. Install thechild restraint system, buckle the seat belt and allow the seat belt to take up any slack. Make sure that the lap por-tion of the belt is tight around the child restraint system and the shoulder por- tion of the belt is positioned so that itcannot interfere with the child's head or neck. After installation of the child re- straint system, try to move it in alldirections to be sure the child restraint system is securely installed.
B230G01A-GAT Installation on Outboard Rear Seats
B230G01A
B230F01A-EAT Installation on Rear Seat Centre Position Use the centre seat belt for the rear to secure the child restraint system as illustrated. After installation of the childrestraint system, rock the child seat back and forth, and side to side to ensure that it is properly secured by theseat belt. If the child seat moves, readjust the length of the seat belt. Then, if equipped,insert the child restraint tether strap hook into the child restraint hook holder and tighten to secure the seat. Alwaysrefer to the child restraint system manufacturer's recommendation before installing the child restraint system inyour vehicle.
B230F01A-E

1CONTROLS AND EQUIPMENT
26
B230D03E-EAT Using a Child Restraint System with "ISOFIX" System and"Tether Anchorage" System
B230D01A
ISOFIX is a standardised method of fitting child seats that eliminates the need to use the standard adult seat beltto secure the seat in the vehicle. This enables a much more secure and posi- tive location with the added benefit ofeasier and quicker installation.
B230E03A
Front of Vehicle
Back Panel Load Space Cover
2. Remove the load space cover.
3. Connect the tether strap hook to the child restraint seat hook holder and tighten to secure the seat.
Tether Strap Hook
B230E03A-GAT Securing a Child Restraint Sys- tem with "Tether Anchorage" System (3/5 Door) Three child restraint hook holders are located on the vertical back panel. (behind rear bumper bar)
1. Route the child restraint seat strap over the seatback. For vehicles with adjustable headrestraint, route the tether strap under the head restraint and between the head restraint posts, otherwise routethe tether strap over the top of the seatback.
route the tether strap over the top of the seatback.
3. Connect the tether strap hook to the child restraint hook holder and tightento secure the seat.