check engine Hyundai Accent 2017 Service Manual

7-25
Maintenance
BRAKE/CLUTCH FLUID
Checking the brake/clutch fluid
level
Check the fluid level in the reservoir peri-
odically. The fluid level should be
between MAX and MIN marks on the
side of the reservoir.
Before removing the reservoir cap and
adding brake/clutch fluid, clean the area
around the reservoir cap thoroughly to
prevent brake/clutch fluid contamination.
If the level is low, add fluid to the MAX
level. The level will fall with accumulated
mileage. This is a normal condition asso-
ciated with the wear of the brake linings.
If the fluid level is excessively low, have
the brake system or clutch (if equipped)
checked by an authorized HYUNDAI
dealer.
Use only the specified brake fluid. (Referto “Recommended lubricants or capaci-ties” in section 8.)
Never mix different types of fluid.
WARNING- Brake/clutch fluid
When changing and adding brake
fluid, handle it carefully. Do not let it
come in contact with your eyes. If
brake fluid should come in contact
with your eyes, immediately flush
them with a large quantity of fresh
tap water. Have your eyes examined
by a doctor as soon as possible.
WARNING - Loss of brake/
clutch fluid
In the event the brake system
requires frequent additions of fluid,
the vehicle should be inspected by
an authorized HYUNDAI dealer.
CAUTION
Do not allow brake fluid to contact
the vehicle's body paint, as paintdamage will result. Brake fluid, which has been exposed to open airfor an extended time should neverbe used as its quality cannot be guaranteed. It should be disposedof properly. Don't put in the wrong kind of fluid. A few drops of miner-al-based oil, such as engine oil, in your brake system can damagebrake system parts.
ORBC070007

7-35
Maintenance
Reset items
Items should be reset after the battery
has been discharged or the battery has
been disconnected.
Sunroof (See section 4)
Trip computer (See section 4)
Climate control system (See section 4)
Clock (See section 4)
Audio (See section 4)WARNING
Before performing maintenance or recharging the battery, turn off
all accessories and stop the
engine.
The negative battery cable must be removed first and installed
last when the battery is discon-
nected.
Operation related to the battery should be done by an authorized
HYUNDAI dealer.
WARNING- Rechargingbattery
When recharging the battery,
observe the following precautions:
The battery must be removed
from the vehicle and placed in an
area with good ventilation.
Do not allow cigarettes, sparks, or flame near the battery.
Watch the battery during charg- ing, and stop or reduce the charg-
ing rate if the battery cells begin
gassing (boiling) violently or if
the temperature of the electrolyte
of any cell exceeds 120°F (49°C).
Wear eye protection when check- ing the battery during charging.
Disconnect the battery charger in the following order.
1. Turn off the battery charger main switch.
2. Unhook the negative clamp from the negative battery terminal.
3. Unhook the positive clamp from the positive battery terminal.

Maintenance
7-50
A vehicle’s electrical system is protected
from electrical overload damage by fuses.
This vehicle has 2 fuse panels, one locat-
ed in the driver’s side panel bolster, the
other in the engine compartment.If any of your vehicle’s lights, accessories,
or controls do not work, check the appro-
priate circuit fuse. If a fuse has blown, the
element inside the fuse will be melted.
If the electrical system does not work, first
check the driver’s side fuse panel.
Before replacing a blown fuse, move to
safe place, turn off the engine and all
electric devices, and then disconnect the
negative battery cable.
Always replace a blown fuse with one of
the same rating.
If the replacement fuse blows, this indi-
cates an electrical problem. Avoid using
the system involved and immediately
consult an authorized HYUNDAI dealer.
Three kinds of fuses are used: blade type
for lower amperage rating, cartridge type,and multi fuse for higher amperage ratings.
WARNING - Fuse replace- ment
Never replace a fuse with any-
thing but another fuse of the
same rating.
A higher capacity fuse could cause damage and possibly a fire.
Never install a wire or aluminum foil instead of the proper fuse -
even as a temporary repair. It may
cause extensive wiring damage
and a possible fire.
CAUTION
Do not use a screwdriver or anyother metal object to remove fuses because it may cause a short circuitand damage the system.
ORB072110
Normal
Normal
Blade type
Cartridge type
Multi fuse Blown
Blown
Normal Blown
FUSES

7-51
Maintenance
✽
✽NOTICE
The actual fuse/relay panel label may
differ from equipped items.
Instrument panel fuse replace-
ment
1. Turn the ignition switch and all other
switches off.
2. Open the fuse panel cover. 3. Pull the suspected fuse straight out.
Use the removal tool provided in the
engine compartment fuse panel.
4. Check the removed fuse; replace it if it is blown.
5. Push in a new fuse of the same rating, and make sure it fits tightly in the clips.
If it fits loosely, consult an authorized
HYUNDAI dealer.
If you do not have a spare, use a fuse of the same rating from a circuit you maynot need for operating the vehicle, suchas the cigarette lighter fuse.
If the headlights or other electrical com-
ponents do not work and the fuses are
OK, check the fuse panel in the engine
compartment. If a fuse is blown, it must
be replaced.
CAUTION
When replacing a blown fuse or relay with a new one, make surethe new fuse or relay fits tightlyinto the clips. The incomplete fas-tening fuse or relay may cause the vehicle wiring and electric sys-tems damage and a possible fire.
Do not remove fuses, relays and terminals fastened with bolts ornuts. The fuses, relays and termi-nals may be fastened incomplete-ly, and it may cause a possiblefire. If fuses, relays and terminalsfastened with bolts or nuts areblown, consult an authorizedHYUNDAI dealer.
Do not input any other objects except fuses or relays intofuse/relay terminals such as a driv-er or wiring. It may cause contactfailure and system malfunction.
ORB070018
Driver’s side panel
ORB070019

7-53
Maintenance
Engine compartment fuse
replacement
1. Turn the ignition switch and all otherswitches off.
2. Remove the fuse panel cover by pressing the tab and pulling up.
3. Check the removed fuse; replace it if it is blown. To remove or insert the fuse,
use the fuse puller in the engine com-
partment fuse panel.
4. Push in a new fuse of the same rating, and make sure it fits tightly in the clips.
If it fits loosely, consult an authorized
HYUNDAI dealer.
Multi fuse
If the multi fuse is blown, replace the fuse
with a new one of the same rating when
the ignition switch and all other switches
are off.
CAUTION
After checking the fuse panel in theengine compartment, securelyinstall the fuse panel cover. If not,electrical failures may occur fromwater contact.
ORB070021ORB070022
CAUTION
Before removing the multi fuse, disconnect the (-) terminal of bat-tery.
Do not disassemble or assemble the multi fuse fastened with boltsor nuts. The fuse may be fastenedincompletely, and it may cause apossible fire. If the multi fuse isblown, consult an authorized HYUNDAI dealer.

7-59
Maintenance
Engine compartment main fuse panel
DescriptionFuse rating Protected component
MULTI FUSE MDPS
80A EPS Control Module
BLOWER 40A Blower Relay
RR HTD 40A I/P Junction Box (Rear Defogger Relay)
ABS 2 40A ABS Control Module, ESC Control Module
ABS 1 40A ABS Control Module, ESC Control Module, Multipurpose Check Connector
ALT 125AAlternator, E/R Fuse & Relay Box
(Multi Fuse : ABS 1, ABS 2, MDPS, RR HTD, BLOWER, Fuse : A/CON)
B+1 50AI/P Junction Box (Power Connector Fuse : ROOM LP 1, AUDIO, Fuse : FOG LP FRT,
ROOM LP 2, STOP LP, Relay : Tail Lamp)
FUSE
IG240AStart Relay, Ignition Switch
IG140AIgnition Switch
ECU 1 30A Fuse : ECU 2, Engine Control Relay
C/FAN 40A Cooling Fan (High) Relay, Cooling Fan (Low) Relay
B+2 50A I/P Junction Box (Fuse : S/HEATER, SUNROOF, DR LOCK, HAZARD, Relay : Power Window)
HORN 10A Horn Relay
F/PUMP 15A Fuel Pump Relay
H/LAMP RH 10A Head Lamp RH
H/LAMP LH 10A Head Lamp LH
H/LAMP 10A Engine Compartment Fuse & Relay Box (Head Lamp Relay)
INJECTOR 15A ECM, PCM, Oil Control Valve #1/#2, Oxygen Sensor (Up)/(Down), Fuel Pump Relay
SENSOR 10A
ECM, PCM, Canister Purge Control Solenoid Valve, Variable Intake Solenoid Valve, Canister Close
Valve, Immobilizer Module, A/CON Relay, Cooling Fan (High) Relay, Cooling Fan (Low) Relay
ECU 210A ECM, PCM
IGN COIL 15A Ignition Coil #1 ~ #4, Condenser
B/UP LAMP 10APCM, Transaxle Range Switch, Instrument Cluster,
Rear Combination Lamp LH/RH, ATM Shift Lever Switch ILL.
WIPER 10A ECM, PCM, Multifunction Switch (Wiper), Front Wiper Motor

7-77
Maintenance
3. Exhaust emission control system
The Exhaust Emission Control System is
a highly effective system which controls
exhaust emissions while maintaining
good vehicle performance.
Vehicle modifications
This vehicle should not be modified.
Modification of your vehicle could
affect its performance, safety or dura-
bility and may even violate governmen-
tal safety and emissions regulations. In
addition, damage or performance prob-
lems resulting from any modification
may not be covered under warranty.
If you use unauthorized electronic devices, it may cause the vehicle to
operate abnormally, wire damage, bat-
tery discharge and fire. For your safety,
do not use unauthorized electronic
devices.
Engine exhaust gas precautions
(carbon monoxide)
Carbon monoxide can be present with other exhaust fumes. Therefore, if you
smell exhaust fumes of any kind inside
your vehicle, have it inspected and
repaired immediately. If you ever sus-
pect exhaust fumes are coming into
your vehicle, drive it only with all the
windows fully open. Have your vehicle
checked and repaired immediately. Do not operate the engine in confined or
closed areas (such as garages) any
more than what is necessary to move
the vehicle in or out of the area.
When the vehicle is stopped in an open area for more than a short time with the
engine running, adjust the ventilation
system (as needed) to draw outside air
into the vehicle.
Never sit in a parked or stopped vehicle for any extended time with the engine
running.
When the engine stalls or fails to start, excessive attempts to restart the engine
may cause damage to the emission con-
trol system.
WARNING- Exhaust
Engine exhaust gases contain car-
bon monoxide (CO). Though color-
less and odorless, it is dangerous
and could be lethal if inhaled.
Follow the instructions on this
page to avoid CO poisoning.
CALIFORNIA PROPOSI-
TION 65 WARNING
Engine exhaust and a wide variety
of automobile components and
parts, including components found
in the interior furnishings in a vehi-
cle, contain or emit chemicals
known to the State of California to
cause cancer and birth defects and
reproductive harm. In addition, cer-
tain fluids contained in vehicles
and certain products of component
wear contain or emit chemicals
known to the State of California to
cause cancer and birth defects or
other reproductive harm.

Specifications, Consumer information, Reporting safety defeccts
8-6
Recommended SAE viscosity
number Engine oil viscosity (thickness) has an
effect on fuel economy and cold weather
operating (engine start and engine oil
flowability). Lower viscosity engine oils
can provide better fuel economy and cold
weather performance, however, higher
viscosity engine oils are required for sat-
isfactory lubrication in hot weather. Using
oils of any viscosity other than those rec-
ommended could result in engine dam-
age.When choosing an oil, consider the range
of temperature your vehicle will be oper-
ated in before the next oil change.
Proceed to select the recommended oil
viscosity from the chart.
CAUTION
Always be sure to clean the area
around any filler plug, drain plug, ordipstick before checking or drain- ing any lubricant. This is especiallyimportant in dusty or sandy areasand when the vehicle is used onunpaved roads. Cleaning the plugand dipstick areas will prevent dirtand grit from entering the engineand other mechanisms that couldbe damaged.
*1. For better fuel economy, it is recommended to use the engine oil of
a viscosity grade SAE 5W-20 (API SM / ILSAC GF-4). However, if
the engine oil is not available in your country, select the proper
engine oil using the engine oil viscosity chart.
Temperature Range for SAE Viscosity Numbers
Temperature -30 -20 -10 0 10 20 30 40 50
-10 0 20 40 60 80 100 120
Engine Oil *110W-30
5W-20, 5W-30
°C
(°F)

I3
Index
Cargo capacity··················\
··················\
·········· ·5-41
Cargo weight ··················\
··················\
············ ·5-45
Center console storage ··················\
··················\
· ·4-75
Central door lock switch ··················\
··················\
·4-8
Certification label ··················\
··················\
······· ·5-43
Certification label ··················\
··················\
·········8-7
Chains Tire chains ··················\
··················\
············ ·5-37
Changing tires ··················\
··················\
··········· ·6-18
Checking tire inflation pressure ··················\
·········7-37
Child restraint system ··················\
··················\
·· ·3-25
Lower anchor ··················\
··················\
·········3-31
Seat belt ··················\
··················\
··············· ·3-26
Tether anchor system ··················\
················· ·3-29
Child-protector rear door lock ··················\
·············4-9
Climate control air filter ··················\
················· ·4-64
Climate control air filter ··················\
················· ·7-28
Clock (Digital) ··················\
··················\
·········· ·4-80
Clothes hanger ··················\
··················\
·········· ·4-80
Combined instrument, see instrument cluster ···········4-29
Compact spare tire ··················\
··················\
······ ·6-22
Compact spare tire replacement ··················\
·········7-41
Coolant ··················\
··················\
··················\
· ·7-22
Cooling fluid, see engine coolant ··················\
·······7-22
Crankcase emission control system ··················\
·····7-75
Cruise control system ··················\
··················\
·· ·5-26
Cup holder ··················\
··················\
··············· ·4-78
Curtain air bag ··················\
··················\
·········· ·3-50Dashboard illumination,
see instrument panel illumination ··················\
····4-30
Dashboard, see instrument cluster ··················\
·······4-29
Defogging (Windshield) ··················\
················· ·4-71
Defogging logic (Windshield) ··················\
···········4-73
Defroster (Rear window) ··················\
················ ·4-55
Defrosting (Windshield) ··················\
················· ·4-71
Digital clock ··················\
··················\
··············4-80
Dimensions ··················\
··················\
·················8-2
Display illumination, see instrument panel illumination
·4-30
Displays, see instrument cluster ··················\
·········4-29
Door locks ··················\
··················\
················· ·4-6
Central door lock switch ··················\
··············· ·4-8
Child-protector rear door lock ··················\
·········4-9
Drinks holders, see cup holders ··················\
·········4-78
Driver's 3-point seat belt ··················\
················· ·3-15
Driver's and passenger's front air bag ··················\
···3-45
Driving at night ··················\
··················\
········· ·5-33
Driving in flooded areas ··················\
················· ·5-34
Driving in the rain ··················\
··················\
······ ·5-34
Economical operation ··················\
··················\
·· ·5-30
Electric power steering ··················\
··················\
· ·4-24
Electronic stability control (ESC) ··················\
·······5-20
D
E

Index
8I
Spare tireCompact spare tire ··················\
··················\
·· ·6-22
Compact spare tire replacement ··················\
······7-42
Removing and storing the spare tire ··················\
·6-18
Special driving conditions ··················\
··············· ·5-32
Driving at night ··················\
··················\
······ ·5-33
Driving in flooded areas ··················\
···············5-34
Driving in the rain ··················\
··················\
··· ·5-34
Hazardous driving conditions ··················\
········5-32
Highway driving ··················\
··················\
····· ·5-35
Rocking the vehicle ··················\
··················\
· ·5-32
Smooth cornering ··················\
··················\
··· ·5-33
Speedometer ··················\
··················\
··············4-30
SRS components and functions ··················\
··········3-36
Starting difficulties, see engine will not start ·············6-3
Steering wheel ··················\
··················\
··········· ·4-24
Electric power steering ··················\
··············· ·4-24
Horn ··················\
··················\
··················\
· ·4-26
Tilt and telescopic steering ··················\
············4-25
Steering wheel audio control ··················\
·············4-85
Steps For Determining Correct Load Limit ··············5-41
Storage compartment ··················\
··················\
··· ·4-75
Center console storage ··················\
················ ·4-75
Glove box ··················\
··················\
············ ·4-76
Luggage net ··················\
··················\
·········· ·4-77
Sliding armrest ··················\
··················\
······· ·4-76
Sunglass holder ··················\
··················\
······ ·4-76Sunroof
··················\
··················\
··················\
· ·4-21
Sunvisor ··················\
··················\
··················\
·4-78
Tachometer ··················\
··················\
·············· ·4-30
Tailgate ··················\
··················\
··················\
· ·4-12
Tether anchor system ··················\
··················\
··· ·3-29
Tilt and telescopic steering ··················\
··············4-25
Tire and loading information label ··················\
······5-40
Tire chains ··················\
··················\
··············· ·5-37
Tire mobility kit ··················\
··················\
········· ·6-25
T
ire pressure monitoring system (TPMS) ··········6-7, 6-12
Tire specification and pressure label ··················\
·····8-7
Tires and wheels ··················\
··················\
·········7-36
Checking tire inflation pressure ··················\
······7-37
Compact spare tire replacement ··················\
······7-41
Low aspect ratio tire ··················\
··················\
·7-45
Recommended cold tire inflation pressures ··········7-36
Tire care ··················\
··················\
·············· ·7-36
Tire maintenance ··················\
··················\
···· ·7-41
Tire replacement ··················\
··················\
····· ·7-40
Tire rotation ··················\
··················\
·········· ·7-38
Tire sidewall labeling ··················\
················· ·7-42
Tire traction ··················\
··················\
·········· ·7-41
Wheel alignment and tire balance ··················\
···7-39
Wheel replacement ··················\
··················\
·· ·7-40
T