ignition Hyundai Azera 2005 User Guide

1
FEATURES OF YOUR HYUNDAI
19
!WARNING:
o Be careful that someone's head, hands and body are not trapped by a closing window.
o Never try to operate the main switch on the driver's door andthe individual door windowswitch in opposing directions at the same time. If this is done, the window will stop and cannot beopened or closed.
o Do not leave children alone in the
car. Always remove the ignition key for their safety. B060D01TG-GAT Closing and Opening the Win- dows with a Key The driver’s and passenger’s windows can be closed or opened with a key inthe driver’s door.
To close the windows, turn the key toward the front of the vehicle for 3 seconds. If the key is turned toward the rear of thevehicle while closing the window, the window will stop upward movement.
HTG2201
To open the windows, turn the key toward the rear of the vehicle for 3 seconds. If the key is turned toward the front of the vehicle while opening the window, the window will stop downward move-ment.
HTG2200
!WARNING:
Be careful that someone’s head, hands and body are not trapped by a closing window.

1FEATURES OF YOUR HYUNDAI
26
NOTE:
o If the battery has been rechargedor disconnected, the driving posi- tion memory will be lost.
o The buzzer sounds 10 times if there is a malfunction of theintergrated memory system. Havethe I.M.S checked by an autho- rized Hyundai dealer.
I.M.S control switch It is located on the driver's door trim and will function as follows; SET : When the button is pressed, the
system will memorize the posi- tion with a beep sound.
1,2 : It indicates that the system can
memorize positions up to 2 occu-pants.
B090E01TG-AAT Lumbar Support Control (Driver's seat only) To adjust the lumbar support, press the control switch the outboard side of the seat cushion. To increase the amount of lumbar support, press the front por-tion of the switch. To decrease it, press the rear portion of the switch. HTG2042-2
I.M.S (INTEGRATED MEMORY SYSTEM)
B090E01TG-GAT (If Installed) The Integrated Memory System con- trols are located on the driver's door trim. After adjusting the position of thedriver's seat and steering wheel col- umn (with electric tilt and telescopic type), use the I.M.S to memorize them.Two different driving position profiles can be entered in the I.M.S. If you turn the ignition key to the "ON" position, thememorized position is adjusted auto- matically. B090E01TG

1
FEATURES OF YOUR HYUNDAI
27
CAUTION:
In the following conditions, the I.M.S will not activate.
1. When the key is in the "OFF" posi- tion.
2. When the vehicle is running above 3 km/h.
3. When the seat is being adjusted.
4. When the shift lever is positioned in other than "P" position.
! CAUTION:
In the following conditions, the I.M.S will not memorize.
1. When the "1" or "2" button is not pushed within five seconds.
2. When the seat is being adjusted.
3. When the key is not in the "ON"
position.
4. When the shift lever is positioned in other than "P" position. To activate the memorized posi- tion
1. Place the shift lever into "P" while
the ignition switch is ON.
2. When you push button "1" or "2", the driving position will be automatically adjusted to the position recorded forthat button.
!
To memorize driving position
1. Place the shift lever into "P" while
the ignition switch is ON.
2. Adjust the driver's seat and steering wheel column (with electric tilt and telescopic type) to the desired posi-tion.
3. Push the "SET" button on the I.M.S
until the signal beeps.
4. Within five seconds, push button "1" or "2" until the signal beeps twice.The beep sounds mean that the po-sitions are memorized in the I.M.S. Reverse Parking Aid Function While the vehicle is moving backward, the outside rearview mirror(s) will movedownward to aid reverse parking safely. According to the position of the outside rearview mirror switch knob, the out-side rearview mirror(s) will operate as follows.B090E02TG

1FEATURES OF YOUR HYUNDAI
28
!
NOTE:
o The seat warmer may not operate
if ambient temperature is warm enough.
o If the seat warmer doesn't work when the ambient temperature islower than 24°C, it must bechecked at an authorized dealer.
WARNING:
Be very careful not to injure by lowtemperature burn or an attack offever as following occupants; infants, children, old man, drunken man, people who is taken sleeping drug orcold remedy.B100A01TG-GAT SEAT WARMER (If Installed) The front seats can be electrically heated individually when the ignition switch is ON. When the switch is ON, anumber ranging from 1 to 5 is displayed on the switch (5 = warmest setting). To turn off the seat warmer, set theswitch to 0. B100A01TG
L
: When the remote control outside
rearview mirror switch knob is se-lected to the "L" position, both ofthe outside rearview mirrors will move downward.
R : When the remote control outside
rearview mirror switch knob is se-lected to the "R" position, only thepassenger's outside rearview mir- ror will move downward.
Neutral :When the remote control out-
side rearview mirror switchknob is placed in the middle position, the outside rearviewmirrors will not operate while the vehicle is moving back- ward.
NOTE: When the ignition key is in the "LOCK" position, the shift lever is moved to any position except "R"position, or the remote control out- side rearview mirror switch knob is placed in the middle position, theoutside rearview mirrors will auto- matically revert to original position.

1FEATURES OF YOUR HYUNDAI
34
It will also lock if you try to lean forward too quickly. Check to make sure thatthe belt is properly locked and that the belt is not twisted. NOTE: If the seat belt is not fastened when the ignition key is turned from the "OFF" position to the "ON" position, the seat belt warning will activate toremind the driver and front passen- ger to fasten the seat belt as follows. B260E01TG-GAT Seat Belt Warning Light
(Except E.C)
The seat belt warning light blinks for about 6 seconds when the ignition keyis turned from the "OFF" position to the "ON". NOTE: You can find the front passenger's seat belt warning light on the center fascia panel.
*1) When the ignition key is turned from "OFF" position to "ON" within 1 minute.
*2) If the vehicle speed exceeds 9km/ h, the seat belt chime also soundsfor about 1~2 minutes.If the vehicle speed is below 9km/h, 1 minute later the seat belt chime also sounds for about 1~2 minutes.
The seat belt warning light and chimewill activate to the following table.
B265E01TG-GAT
Seat Belt Warning Light
and Chime (E.C only)
User (Driver+Front Passenger) Condition Sat Belt WarningLight
Seat Belt Ignition Switch
Unbuckled ON Stay on until buckled up
Buckled ON Come on for 6 seconds
Unbuckled ON * 1
Blink until buckled up
ON Blink until buckled up* 2
Buckled



Unbuckled NOTE:
o You can find the front passenger's
seat belt warning light on the cen- ter fascia panel.
o If the driver's seat belt is operated in this order "unbuckled

buck-
led

unbuckled" within 9 sec-
onds after the seat belt is buckled, the seat belt warning light and chime will not activate.
o Although the front passenger seat is not occupied, the seat belt warn-ing light will illuminate for 6 sec-onds.
o The seat belt warning light can be
operated when luggage is placedon the front passenger seat.

1
FEATURES OF YOUR HYUNDAI
45
!!
AIR
BAG
CAUTION:
o Because the sensor that activates the SRS airbag is connected with pre-tensioner seat belt, the SRS airbag warning light on the instrument panel will illuminatefor approximately 6 seconds af- ter the ignition key has been turned to the "ON" position, andthen it should turn off.
o If pre-tensioner seat belt is not
working properly, this warninglight will illuminate even if there is no malfunction of the SRS airbag. If the SRS airbag warninglight does not illuminate when the ignition key is turned to "ON", or if it blinks for a second andremains illuminated after illumi- nating for approximately 6 sec- onds, or if it illuminates while thevehicle is being driven, please have an authorized Hyundai dealer inspect the pre-tensioner seat beltor SRS airbag system as soon as possible. WARNING:
o Pre-tensioners are designed to operate only one time. After acti- vation, pre-tensioner seat beltsmust be replaced. All seat belts, of any type, should always be replaced after they have beenworn during a collision.
o The pre-tensioner seat belt as-
sembly mechanisms become hotduring activation. Do not touch the pre-tensioner seat belt as- semblies for several minutes af- ter they have been activated.
o Do not attempt to inspect or re-
place the pre-tensioner seat beltsyourself. This must be done by an authorized Hyundai dealer.
o Do not strike the pre-tensioner seat belt assemblies.
o Do not attempt to service or repair the pre-tensioner seat belt system in any manner.
o Improper handling of the pre-tensioner seat belt assemblies, and failure to heed the warnings not tostrike, modify, inspect, replace, service or repair the pre-tensioner seat belt assemblies may lead toimproper operation or inadvertent activation and serious injury.
o Always wear the seat belts when driving or riding in a motor ve-hicle.

1
FEATURES OF YOUR HYUNDAI
49
B240B03L
Upon deployment, tear seams molded directly into the pad covers will sepa-rate under pressure from the expan- sion of the airbags. Further opening of the covers then allows full inflation ofthe airbags.
B240B02L
The SRS service reminder indicator(SRI) on the instrument panel will illu-minate for about 6 seconds after the ignition key is turned to the "ON" posi- tion or after the engine is started, afterwhich the SRI should go out. The airbag modules are located both in the center of the steering wheel and in the front passenger's panel above the glove box. When the SRSCM detects aconsiderable impact to the front of the vehicle, it will automatically deploy the airbags.
A fully inflated airbag in combination with a properly worn seat belt slows the driver's or the passenger's forwardmotion, thus reducing the risk of head or chest injury. After complete inflation, the airbag immediately starts deflating, enabling the driver to maintain forward visibility.
B240B01NF-GAT SRS Components and Functions
The SRS consists of the following com- ponents:
- Driver's Front Airbag Module
- Passenger's Front Airbag Module
- Knee bolster
- SRS Service Reminder Indicator (SRI)
- SRS Control Module (SRSCM) The SRSCM continually monitors all elements while the ignition is "ON" todetermine if a frontal or near-frontal impact is severe enough to require airbag deployment. B240B01L

1FEATURES OF YOUR HYUNDAI
50
!
However, the fine dust generated during airbag deployment may cause skin irritation. Wash all exposed skin areas thoroughlywith lukewarm water and a mild soap after an accident in which the airbags were deployed.
o The SRS can function only when the ignition key is in the "ON"position.If the SRS is not working prop- erly,
(1)The SRS SRI does not come on when the ignition key isturned to the "ON" position or after the engine is started.
(2)The SRS SRI blinks for a sec- ond and remains on after illu-minating for about 6 secondswhen the ignition key is turned to the "ON" position or after he engine is started.
(3)The SRS SRI illuminates while driving.
If this occurs, have your vehicleimmediately inspected by your Hyundai dealer.
Passenger's Front Airbag
B240B05L
freshener onto these areas (Instru-ment cluster, instrument panel pad or air ventilator), it may damagethese parts. If the liquid from air freshener does leak onto these areas, wash them with water im-mediately.
WARNING:
o When the SRS is activated, there may be a loud noise and fine dustwill be released throughout the vehicle. These conditions are normal and are not hazardous.
CAUTION:
o Do not install or place any acces- sories (drink holder, cassette holder, sticker, etc.) on the front passenger's panel above theglove box in a vehicle with a passenger's front airbag. Such ob- jects may become dangerous pro-jectiles and cause injury if the passenger's front airbag inflates.
o When installing a container of
liquid air freshener inside a ve-hicle, do not place it near the instrument cluster nor on the in-strument panel pad surface. If there is any leakage from the air B240B01TG
Passenger's Front Airbag!

1
FEATURES OF YOUR HYUNDAI
51
B990A01TG-GAT Passenger's Front Airbag ON/ OFF Switch (If Installed)
B990A01TG
The passenger's front airbag can be deactivated by the passenger's frontairbag ON/OFF switch (1) if a child restraint is installed on the front passenger's seat or if the frontpassenger's seat is unoccupied by a person. To ensure the safety of your child, thepassenger's front airbag must be de- activated when it should be necessary to install a rearward facing child seaton the front passenger seat in excep- tional circumstances. To deactivate or reactivate the passenger's front airbag To deactivate the passenger's front airbag, insert the master key into thepassenger's front airbag ON/OFF switch on the right side of the crash pad and
turn it to the "OFF" position. Thepassenger's front airbag OFF indicator will illuminate and stay on until the passenger's front airbag is reactivated. To reactivate the passenger's front airbag, insert the master key into thepassenger's front airbag ON/OFF switch and turn it to the "ON" position. The passenger's front airbag OFF in-dicator will go out.
(1)o Before you replace a fuse or dis-
connect a battery terminal, turn the ignition key to the "LOCK" position or remove the ignition key. Never remove or replace theair bag related fuse(s) when the ignition key is in the "ON" posi- tion. Failure to heed this warningwill cause the SRS SRI to illumi- nate.

1FEATURES OF YOUR HYUNDAI
52
!WARNING:
o The driver is responsible for the proper position of the passenger's front airbag ON/OFF switch.
o Deactivate the front passenger's airbag only when the ignitionswitch is switched off, or the mal- function may occur in the SRSCM(SRS Control Module). And there may be a danger that the driver's and/or passenger's front and/orside and curtain airbag may fail to trigger, or not trigger correctly during a collision.
o Never install a rearward facing child seat on the frontpassenger's seat. The infant orchild could be severely injured or killed by an airbag deploy- ment in case of an accident.
o If the SRS airbag warning light
does not illuminate when the ig-nition key is turned to the "ON" position, or if it illuminates while the vehicle is being driven, havean authorized Hyundai dealer in- spect the passenger's front airbag ON/OFF switch, pre-tensioner seat belt and the SRS airbag system as soon as pos- sible.! CAUTION:
o If the passenger's front airbag ON/OFF switch is not working properly, the SRS warning light on the instrument panel will illu-minate. And, the passenger's front airbag OFF indicator will not illuminate,the SRSCM(SRS Control Module) reactivate the passenger's front airbag and the passenger's frontairbag will inflate in frontal im- pact crashes even if the passenger's front airbag ON/OFFswitch is set to "OFF" position. If this occurs, have an authorized Hyundai dealer inspect thepassenger's front airbag ON/OFF switch, the pre-tensioner seat belt system and the SRS airbag sys-tem as soon as possible.