air filter Hyundai Coupe 2003 User Guide

CONTROLS AND EQUIPMENT
1- 62
B760A01E
The air conditioner filter is located in front of the blower uniit behind the glove box.It operates to decrease pollutants from enteringthe car and to filter the air. CAUTION:
o Replace the filter every 20,000 km (12,000 miles) or once a year. If the car is beingdriven in severe conditions such as dusty,rough roads, more frequent air filter in-spections and changes are required.
o When the air flow rate is decreased, it must be checked at an authorized dealer.
Evaporator coreBlower fan
Heater core
B760A03GK-EAT AIR CONDITIONER FILTER (IN FRONT OF BLOWER UNIT)
Outside air
Filter
Inside air
Inside air
Floor-Defrost Level
When selecting the "Floor-Defrost" mode, the indicator light will come on and the air will bedischarged through the windscreen defrostnozzle, the floor vents, side defroster nozzle,side ventilator. B980F01E-EAT Defrost Switch When the "Defrost" button is pressed, the " " mode will be automatically selected and the airwill be discharged through the windscreen de-frost vents. To assist in defrosting, the air condi-tioning will operate if ambient temperature ishigher than 38.3°F(3.5°C) and automatically turnsoff if the ambient temperature drops below38.3°F(3.5°C).
HGK012
B740D01A-AAT Operation Tips
o If the interior of the car is hot when you first get in, open the windows for a few minutes to expel the hot air.
o When you are using the air conditioning sys- tem, keep all windows closed to keep hot airout.
o When moving slowly, as in heavy traffic, shift to a lower gear. This increases engine speed,which in turn increases the speed of the airconditioning compressor.
o On steep grades, turn the air conditioner off to avoid the possibility of the engine over-heating.
o During winter months or in periods when the air conditioner is not used regularly, run theair conditioner once every month for a fewminutes. This will help circulate the lubricantsand keep your system in peak operatingcondition.

VEHICLE MAINTENANCE REQUIREMENTS
5- 2
SF040A3-E SCHEDULED MAINTENANCEIn order to ensure the continued safety, reliability and longevity of the vehicle, the following maintenance service operations should be performed at the timeor mileage intervals specified.It is recommended that all routine maintenance services are entrusted to a
Hyundai dealer to ensure that the manufacturers recommended proceduresare employed and that only genuine Hyundai replacement parts are used.Incorrect maintenance techniques or the use of non genuine replacement partsmay invalidate the vehicle warranty.
F030B01GK-EAT R : REPLACE I : INSPECT AND, AFTER INSPECTION, CLEAN, ADJUST, REPAIR OR REPLACE IF NECESSARY
ENGINE CONTROL SYSTEM MAINTENANCE
ENGINE OIL & FILTER(SG OR ABOVE) See Note (1)
DRIVE BELT 2.0 DOHC CVVT (ALT, W/PUMP, P/STR'G) 1.6 DOHC / 2.7 V6 (AUTO-TENSIONER, ALT, P/STR'G, A/CON)
FUEL FILTER(MPI TYPE)FLUID LEAKS TIMING BELTVENTILATION HOSE AIR CLEANER FILTER SPARK PLUG(1.6/2.0L)SPARK PLUGS(2.7L) VALVE CLEARENCE (2.0 DOHC CVVT)
NO. DESCRIPTION60 72
R I I I
RR R R
5060
R
I I I
4048
R I
R I
R R
30 36
R I I I I
20 24
R I I
R R
10 12
R
I I
MILES X 1000 MONTHS
Note :
(1) SF OR LOWER: EVERY 6,000 MILES OR 6 MONTHS: "R"
FOR 2.0 L DOHC VVT : SH (API), GF-1 (ILSAC) ABOVE
(2) FOR EVERY 60,000 MILES OR 48 MONTHS, WHICHEVER OCCURS FIRST : "I"
1 2 3 4 56 7 8 9
See Note (2)

VEHICLE MAINTENANCE REQUIREMENTS 5-3
I I I I II I I I I
R
III I II I I
F030C02GK-EAT R : REPLACE I : INSPECT AND, AFTER INSPECTION, CLEAN, ADJUST, REPAIR OR REPLACE IF NECESSARY
GENERAL MAINTENANCE COOLING SYSTEM COOLANT COOLANT SPECIFIC GRAVITYMANUAL TRANSAXLE OIL AUTOMATIC TRANSAXLE FLUID BRAKE PIPES, HOSES, AND CONNECTIONSBRAKE FLUID CLUTCH FLUID REAR BRAKE LININGS AND CYLINDERSBRAKE PADS SUSPENSION AND STEERING SYSTEM FRONT SUSPENSION BALL JOINTSPOLLEN FILTER (For Blower unit) REAR WHEEL BEARINGS TYRE CONDITION AND PRESSURE (incl. Spare)LUBRICATE LOCKS AND HINGES CHECK ALL ELECTRICAL SYSTEMS ROAD TESTCHECK ALL SYSTEMS WITH HI-SCAN CHECK 4 GAS DRIVE SHAFT & BOOT
MILES X 1000 MONTHS
NO. DESCRIPTION1 2 34 5 67 8 9
10 11 1213 14 1516 17 1819 20 21I I I I II I I I I
R
III I II I I
10 12 202430364048 50606072
I
R I I I I
R R I I I I
R
III I II I II
R I I I I
R R I I I I
R
III I II I I I I I I II I I I I
R
III I II I I I
R II
R I
R R I I I I
R
III I II I I

VEHICLE MAINTENANCE REQUIREMENTS
5- 4 MAINTENANCE UNDER SEVERE USAGE CONDITIONS
The following items must be serviced more frequently on cars normally used under severe driving conditions. Refer to the chart below for the appropriate maintenance intervals. R : Replace I : Inspect and, after inspection, clean, adjust, repair or replace if necessary
F040A02GK-EAT
DRIVING
CONDITION
R R RR
I I II
R RR
MAINTENANCE ITEM MAINTENANCE
OPERATION MAINTENANCE
INTERVALS
ENGINE OIL AND FILTER AIR CLEANER FILTER SPARK PLUGSTIMING BELTBRAKE PADS, CALIPERS AND ROTORSREAR BRAKE DRUMS/LININGS, PARKING BRAKESTEERING GEAR BOX, LINKAGE & BOOTS/LOWER ARM BALL JOINTDRIVESHAFTS & BOOTSMANUAL TRANSAXLE OILAUTOMATIC TRANSAXLE FLUIDPOLLEN FILTER(FOR BLOWER UNIT) EVERY 4,500MILES OR 6 MONTHSEVERY 3,000MILES OR 6 MONTHSMORE FREQUENTLYMORE FREQUENTLYEVERY 37,000MILES OR 48MONTHSMORE FREQUENTLYMORE FREQUENTLY MORE FREQUENTLYEVERY 9,000MILES OR 12 MONTHS EVERY 60,000MILESEVERY 27,000MILESMORE FREQUENTLY
A, B, C, F, H C, E B, HD, E, F, GC, D, G, HC, D, G, H C,D,E,FC, D, E, F, G A, C, D, E, F, G, H, I, JA, C, E, F, G, H, IC, E
SEVERE DRIVING CONDITIONS
A - Repeated short distance driving
B - Extensive idling
C - Driving in dusty, rough roads
D - Driving in areas using salt or other corrosive materials or in very cold weather
E - Driving in sandy areas F - More than 50% driving in heavy city traffic during hot weather
above 90°F (32°C)
G - Driving in mountainous areas
H - Towing a trailer
I - Driving as a rental car, taxi, other commercial use or vehicle towing
J - Continuous driving over 100 MPH
1.6 DOHC / 2.7 V6 2.0 DOHC CVVT

VEHICLE MAINTENANCE REQUIREMENTS 5-5
6ZF060D1-A
o Fuel lines, fuel hoses and connec-
tions
Check the fuel lines, fuel hoses and connections for leakage and damage. Replace any damagedor leaking parts immediately. 6ZF060E1-A o Timing beltInspect all parts related to the timing belt for damage and deformation. Replace any dam-aged parts immediately. 6ZF060G1-A
o Vapour hose and fuel filler cap The vapor hose and fuel filler cap should be inspected at those intervals specified in the main-tenance schedule. Make sure that a new vapourhose or fuel filler cap is correctly replaced. 6ZF060F1-A
o Vacuum, crankcase
ventilation hoses
Inspect the surface of hoses for evidence of heat and/or mechanical damage. Hard and brittle rub-ber, cracking, tears, cuts, abrasions, and exces-sive swelling indicate deterioration. Particularattention should be paid to examining those hosesurfaces nearest to high heat sources, such asthe exhaust manifold.Inspect the hose routing to assure that the hoses do not come in contact with any heat source,sharp edges or moving component which mightcause heat damage or mechanical wear. Inspectall hose connections, such as clamps and cou-plings, to make sure they are secure, and that noleaks are present. Hoses should be replacedimmediately if there is any evidence of deteriora-tion or damage. 6ZF060H1-A
o Air cleaner filterA Genuine Hyundai air cleaner filter is recom- mended when the filter is replaced. 6ZF060J1-A
o Spark plugs Make sure to install new spark plugs of the correct heat range.
6ZF060A1-A EXPLANATION OF SCHEDULED MAINTENANCE ITEMS 6ZF060M1-A
o Engine oil and filterThe engine oil and filter should be changed at the intervals specified in the maintenance schedule.If the car is being driven in severe conditions,more frequent oil and filter changes are required. 6ZF060B2-A
o Drive belts Inspect all drive belts for evidence of cuts, cracks, excessive wear or oil saturation and replace ifnecessary. Drive belts should be checked peri-odically for proper tension and adjusted as nec-essary. 6ZF060C1-A
o Fuel filterA clogged filter can limit the speed at which the vehicle may be driven, damage the emissionsystem and cause hard starting. If an excessiveamount of foreign matter accumulates in the fueltank, the filter may require replacement morefrequently.After installing a new filter, run the engine forseveral minutes, and check for leaks at theconnections.
F060N02E-EAT
o Valve Clearance Inspect excessive valve noise and/or engine vibration and adjust if necessary. A qualifiedtechnician should perform the operation.

OWNER MAINTENANCE 6-3
G010B01GK-EAT ENGINE COMPARTMENT (2.7 V6) HGK209-D
1. Power steering fluid reservoir
2. Clutch fluid reservoir (Not all models)
3. Brake Booster
4. Brake fluid reservoir
5. Air filter element 6. Relay box
7. Windscreen washer fluid reservoir cap
8. Engine coolant reservoir
9. Engine oil level dipstick
10. Radiator cap11. Engine oil filler cap
12. Automatic transaxle fluid level dipstick
(Not all medels)
13. Battery
1 23 45
7 8 9 10 11 126
13CAUTION: When inspecting or servicing the engine, youshould handle tools and other heavy objectscarefully so that the plastic rocker cover ofthe engine is not damaged.

OWNER MAINTENANCE 6-7
ways wash thoroughly after any contact. Keep used oils out of reach of children. It is illegalto pollute drains, water courses and soil. Useonly authorized waste collection facilitiesincluding civic amenity sites and garages forthe disposal of used oil and oil filters. If indoubt, contact the local authority for dis-posal instructions. SG050A1-E ENGINE COOLANT CHECKING AND REPLACING WARNING: Do not remove the radiator cap when the engine is hot, since the system is pressurizedand coolant may be ejected from the radiatorresulting in scalding. SG050B1-E Coolant recommendations
Only ethylene glycol based coolant with a corro- sion inhibitor suited to aluminium alloy enginecomponents should be used in the cooling sys-tem. No further additives or inhibitors should beused. The coolant specific gravity should bechecked as prescribed in the maintenance sched-ule to ensure adequate frost and corrosion pro-tection. In addition, the engine coolant must bereplaced at the specified interval since the corro-sion inhibitor properties deteriorate with time.It is important to note that whilst an increase in theconcentration of anti freeze gives an increase inthe level of frost protection, a solution which is inexcess of 65% anti freeze will result in reducedfrost protection and engine overheating. There-fore the recommended concentration of 50%should not be exceeded for general use.The use of methanol based anti freeze com-pounds may result in engine overheating and willinvalidate the vehicle warranty. NOTE: It is imperative that vehicles fitted with an airconditioning system have a coolant concen-tration of the recommended strength at alltimes. The use of the air conditioning systemwhen the cooling system is filled with wateronly will result in the heater matrix freezingand subsequently bursting.SG050C1-E Engine Coolant LevelThe engine coolant level may be observed through the side of the plastic coolant reservoir(expansion tank) when the engine is cold. If thelevel is below the "LOW" mark, add coolant of thecorrect concentration until the level is betweenthe "LOW" and "Full" marks. If the level fallsbelow the "LOW" mark on a regular basis despitebeing topped up, consult a Hyundai dealer. SG050D1-E To Change the Engine CoolantThe engine coolant should be changed at those intervals specified in the vehicle maintenanceschedule in Section 5. NOTE: Care should be taken to ensure that coolantis not allowed to spill onto the paintworksince the finish may become damaged. Ifcoolant spillage occurs, the affected areashould be rinsed thoroughly with water.
1. Park the vehicle on level ground and ensure
that the parking brake is firmly applied, and the engine allowed to cool.DO NOT ATTEMPT THIS OPERATIONWHILST THE ENGINE IS HOT SINCEBURN-ING OR SCALDING MAY RESULT.
2. Prepare a suitable receptacle to collect the displaced coolant and position this under theradiator drain tap.
HGK187

OWNER MAINTENANCE
6-14 SG140B1-E Compressor Drive Belt The air conditioning compressor drive belt should be checked to ensure freedom from damage or excessive wear and correct tension. The belt tension is correct when the belt deflects by about0.3 inches (8 mm) when a force of 98 N is appliedto the belt halfway between the compressor andcrankshaft pulleys. Adjustment of the belt shouldbe entrusted to a Hyundai dealer.
SG140C2-E Checking the Refrigerant
1. Start the engine and run at idle for several
minutes with the refrigeration system running at the coldest setting.
2. If the air coming out of the in-dash vents is not cold, have the air conditioning system in-spected by your Hyundai dealer.
CAUTION:Running the air conditioning system for ex-tended periods of time with a low refrigerantlevel may damage the compressor. A/C
CRANK PULLEY
TENSION PULLEY 0.315 in. (8mm)
G140D01GK
V6
DOHC
Auto tensioner
Eng.pulley COMP
SG140D1-E Off Season Maintenance The air conditioning must be run for ten minutes or so weekly during periods when the systemwould not normally be used to ensure that thecompressor and seals are lubricated. If this pre-caution is not observed the compressor sealsmay become stuck to the compressor shaft anddamaged when the system is next used resultingin a loss of refrigerant and damage to the com-pressor. B760B01GK-GAT Replacement of air conditioner filter:
HGK250-D
1. Remove the mounting screws on the down- side of the glove box.
2. Open the glove box and remove the mounting screws on the upside of the glove box.
HGK251-D

OWNER MAINTENANCE 6-15
4. Replace the air filter with a new one.
5. Installation is the reverse order of disassem-bly. CAUTION:Be sure to install the air filter in the directionof the arrow sign. Otherwise, it may causenoise or deterioration. SG150A1-E STEERING WHEEL FREEPLAY Steering wheel freeplay should be checked to ensure that the specified value is not exceeded.
HGK218
SG160A1-E CLUTCH PEDAL FREEPLAY
SSA6160A
0.24 ~ 0.51 in. (6 ~ 13 mm)
The clutch pedal freeplay should be checked against the specified value. If the freeplay is notcorrect, the clutch should be adjusted by aHyundai dealer.
1.18in.(30 mm)
3. Remove the filter cover.
HGK253-D
HGK254-D

INDEX10-1
C CARE OF CAS
SETTE TAPE ........................................................... 1-65
CARE OF DISC ................................................................................ 1-65
CARE OF SEAT BELTS .................................................................. 1-12
CATALYTIC CONVERTOR OPERATING PRECAUTIONS .......7-1~7-2
CENTRAL DOOR LOCK .................................................................... 1-4
CHANGING A FLAT TYPE ................................................................ 3-3
CHECKING THE CLUTCH FLUID ................................................... 6-13
CHILD RESTRAINT SYSTEM ......................................................... 1-14
CIGAR LIGHTER .............................................................................. 1-37
CLUTCH PEDAL FREEPLAY .......................................................... 6-15
COMBINATION IGNITION SWITCH AND STEERING LOCK .......... 2-2
CRUISE CONTROL ......................................................................... 1-49
D DAILY OPERATING CHECKS ........................................................... 6-4
DEFROSTING/DEFOGGING ........................................................... 1-55
DIGITAL CLOCK .............................................................................. 1-37
DOOR LOCKS .................................................................................... 1-2 DOOR WINDOWS .............................................................................. 1-6
DRINK HOLDER .............................................................................. 1-38
DRIVE BELTS .................................................................................. 6-16
DRIVING FOR ECONOMY .............................................................. 2-10
JK000A2-EAT 10. INDEX
A AIR BAG ........................................................................................... 1-19
AIR CONDITIONING SWITCH ......................................................... 1-56
AIR CONDITIONING SYSTEM MAINTENANCE ............................6-13
AIR CLEANER ELEMENT REPLACEMENT ..................................... 6-9
AIR CONDITIONER FILTER ............................................................ 1-62
ANTENNA ......................................................................................... 1-67
ANTI-LOCK BRAKE SYSTEM ........................................................... 2-8
AUTOMATIC TRANSMISSION FLUID ............................................. 6-11
AUTOMATIC TRANSMISSION .......................................................... 2-5
BBATTERY MAINTENANCE .............................................................. 6-17
BEFORE FOLDING THE REAR SEATS ......................................... 1-10
BEFORE STARTING THE ENGINE .................................................. 2-2
BONNET RELEASE ......................................................................... 1-45
BRAKE PEDAL FREEPLAY ............................................................. 6-16
BRAKE SYSTEM CHECKING ......................................................... 6-12
10