change time Hyundai Coupe 2003 Owner's Guide

CONTROLS AND EQUIPMENT
1- 54
HGK023-D
HGK024-D
Floor-Level
Air is discharged through the floor vents, windscreen defroster nozzle, side defrosternozzle, side ventilator.
Floor-Defrost Level
Air is discharged through the windscreen defrostnozzle, the floor vents, side defroster nozzle,side ventilator.
HGK025-D
Face-Level
Selecting the "Face" mode will cause air to be discharged through the face level vents.
HGK022-D
Bi-Level
Air is discharged through the face vents and the floor vents. This makes it possible to have coolerair from the dashboard vents and warmer air fromthe floor outlets at the same time.
HGK021-D If the "Floor-Defrost" mode is selected, the A/C will be on automatically and it will be changed to"Fresh" mode.
Defrost-Level
Air is discharged through the windscreen defrostnozzle, side defroster nozzle, side ventilator. Ifthe "Defrost" mode is selected, the A/C will be onautomatically and it will be changed to "Fresh"mode.

CONTROLS AND EQUIPMENT1- 55
B690A01S-AAT HEATING CONTROLSFor normal heating operation, set the air intake control to the "Fresh" position and the air flowcontrol to "Floor". For faster heating, the air intake control should be in the "Recirculation" position. If the windows fog up, move the air flow control to the "Def" (defroster) position. (The A/C will be onautomatically and it will be changed to "Fresh"mode.) For maximum heat, move the temperature con- trol to "Warm".
B730A01FC-EAT Operation Tips
o To keep dust or unpleasant fumes from enter-
ing the car through the ventilation system, temporarily set the air intake control at "Recir-culation". Be sure to return the control to"Fresh" when the irritation has passed tokeep fresh air in the vehicle. This will helpkeep the driver alert and comfortable.
o Air for the heating/cooling system is drawn in through the grilles just ahead of the wind-screen. Care should be taken that these arenot blocked by leaves, snow, ice or otherobstructions.
o To prevent interior fog on the windscreen, set the air intake control to the fresh air ( )position and fan speed to the desi-red posi-tion.
NOTE:When the A/C is operated continuously onthe floor-defrost level (
) or defrost level
(), it may cause fog to form on the exterior
windscreen by the temperature differential. At this time set the air flow control to the facelevel position (
)and fan speed control to the
low position.
Use the heating/ventilation system to defrost or defog the windscreen: To remove the interior fog on the windscreen;
o Set the air flow control to the defrost (
)
position. (The A/C will be on automatically and it will be changed to "Fresh" mode.)
o Set the temperature control at the desired position.
o Set the fan speed control between "1" and "4" position.
To remove the frost or exterior fog on thewindscreen;
o Set the air flow control to the defrost (
)
position. (The A/C will be on automatically and it will be changed to "Fresh" mode.)
o Set the temperature control to the warm.
o Set the fan speed control to position "3" or "4". B720A01FC-EAT DEFROSTING/DEFOGGING
HGK002

DRIVING YOUR HYUNDAI
2- 8 when you are driving down a long hill, slow down and shift to a lower gear. When you dothis, engine braking will help slow the car.
o Slow down before shifting to a lower gear. Otherwise, the lower gear may not be en-gaged.
o Always use the parking brake. Do not de- pend on placing the transaxle in "P" to keepthe car from moving.
o Exercise extreme caution when driving on a slippery surface. Be especially careful whenbraking, accelerating or shifting gears. On aslippery surface, an abrupt change in vehi-cle speed can cause the drive wheels tolose traction and the vehicle to go out ofcontrol.
WARNING:
o Avoid high cornering speeds.
o Do not make quick steering wheel move- ments, such as sharp lane changes or fast, sharp turns.
o Always wear your seat belts. In a collision crash, un unbelted personis significantly more likely to die than aperson wearing a seatbelt.
o The risk of rollover is greatly increased if you lose control of your vehicle at high-way speeds.
o Loss of control often occurs if two or more wheels drop off the roadway andthe driver oversteers to reenter the road-way. o In the event your vehicle leaves the road-
way, do not steer sharply. Instead, slowdown before pulling back into the travellanes.
o Never exceed posted speed limits. SC140A1-E EFFECTIVE BRAKING Braking system performance and friction mate- rial life are greatly affected by the driving styleadopted. The following suggestions are made toassist in achieving the best results from thebraking system.
o Anticipate the road and conditions ahead in order that heavy braking may be avoided.
o When descending long gradients, use the engine to assist in retarding the vehicle to minimize the possibility of brake fade occur-ring.
o When trailer towing, ensure that the trailer brakes function correctly and use enginebraking to assist the vehicle braking system.
o Use only genuine Hyundai replacement brake pads and shoes to ensure consistentfriction characteristics and wear rates.
o After driving through deep water (e.g. fording), the brakes may become wet andperformance reduced. Always check brakeefficiency after emerging from the water anddry the brakes by lightly depressing thebrake pedal several times whilst driving slow-ly.
C090I01L-GAT
CAUTION:
o Shift into "R" and "P" position only when the vehicle has completely stopped.
o Do not accelerate the engine in reverse or any of the forward positions with the brakes applied.
o Always apply the footbrake when shift- ing from "P" or "N", to "R", "D"position.
o Do not use the "P" (Park) position in place of the parking brake. Always setthe parking brake, shift the transaxle into"P" (Park) position and turn off the igni-tion when you leave the vehicle, evenmomentarily. Never leave the vehicleunattended while the engine is running.
o Check the automatic transaxle fluid level regularly, and add fluid as necessary.
C090N02O-AAT
Good Driving Practices
o Never move the gear selector lever from "P" or "N" to any other position with the acceler- ator pedal depressed.
o Never move the gear selector lever into "P" when the vehicle is in motion.
o Be sure the car is completely stopped be- fore you attempt to shift into "R".
o Never take the car out of gear and coast down a hill. This may be extremely hazard-ous. Always leave the car in gear whenmoving.
o Do not "ride" the brakes. This can cause them to overheat and malfunction. Instead,

DRIVING YOUR HYUNDAI 2- 13
C190E01GK-EAT
TOWING ATTACHMENTS
It is strongly recommended that only an Hyundai
Approved towing attachment is used to ensure that the loads placed upon the body structureare correctly distributed. The use of a nonapproved attachment will result in the invalida-tion of the vehicle warranty. Hyundai towingattachments are designed and constructed toensure maximum towing performance and easeof fitment. A range of accessories includingelectrical kits and mirrors are available throughthe Hyundai dealer network.
It is of the utmost importance that those areas
of the vehicle which are subjected to greaterstress during towing are maintained in accor-dance with the recommendations given at theend of this book. In addition, the daily operatingchecks relating to engine oil, transaxle oil andtyres must be performed at each refuelling toensure maximum reliability and safety.
The use of a proprietary stabiliser will assist in
achieving an inherently stable outfit but whilstthe use of such equipment will improve thecharacteristics of a balanced outfit, it will notcompensate for a badly loaded and thereforeunstable outfit.
The tyres and braking equipment fitted to the
trailer or caravan must be maintained in accor-dance with the recommendations of the manu-facturer. Special attention should be paid totyres which deteriorate through time and expo- sure rather than as a result of the distancestowed. The inside walls of the tyres should beinspected along with the outside walls for crack-ing and damage. The trailer wheel nut torquemust be checked on a regular basis, preferablybefore each towing session.
The trailer towbar hitch and the safety catch
mechanism must be maintained in good work-ing order. The trailer break away cable or cableshould be inspected for damage and should beattached to the vehicle towing attachment eachand every time the trailer is hitched to thevehicle.
Whilst towing, the performance of the vehicle
will be reduced in terms of acceleration, brakingand handling due to the increased loads placedupon the vehicle. The driver should anticipatethe change in characteristics and adjust thedriving style in keeping with these changes.Care should be exercised when cornering andbraking to prevent the outfit becoming uncon-trollable by reducing cornering speeds and al-lowing increased braking distances.
The driver should exercise care to ensure that
when pulling away from rest particularly onuphill gradients the clutch unit is not subjectedto excessive slippage which will reduce theuseful life of this component. Use of the "Over-drive Off" "2" and "L" positions when drivingvehicles with automatic transaxle will assistwith braking performance when long down hill gradients are encountered. Improved accelera-tion performance will be available by selecting"Overdrive Off","2", or "1" depending upon roadspeed if it is found that the transaxle unit makesan undesirable upshift whilst hill climbing orovertaking. The transaxle unit should be oper-ated in "D" with the Overdrive "On" undernormal circumstances to enhance fuel economyand reduce noise and engine wear.
SSA2200DGross Axle Weight
Gross Vehicle Weight
CAUTION: The use of a badly loaded or overloaded trailer may result in instability. This following specifications are recom- mended when towing a trailer. The loadedtrailer weight or the Gross Train Weightmust not exceed the values in the chartbelow.

DRIVING YOUR HYUNDAI 2- 15
9. If the trailer has electric brakes, start your
vehicle and trailer moving, and then apply the trailer brake controller by hand to besure the brakes are working. This lets youcheck your electrical connection at the sametime.
10. During your trip, check occasionally to be sure that the load is secure, and that thelights and any trailer brakes are still working.
11. Avoid jerky starts, sudden acceleration or sudden stops.
12. Avoid sharp turns and rapid lane changes.
13. Avoid holding the brake pedal down too long or too frequently. This could cause the brakes to overheat, resulting in reduced brakingefficiency.
14. When going down a hill, shift into a lower gear and use the engine braking effect. When ascending a long grade, downshift the transaxle to a lower gear and reduce speedto reduce chances of engine overloadingand/or overheating.
15. If you have to stop while going uphill, do not hold the vehicle in place by pressing on theaccelerator. This can cause the automatictransaxle to overheat. Use the parking brakeor footbrake. NOTE: When towing check transaxle fluid more
frequently.
CAUTION:If overheating should occur when towing,
(temperature gauge reads near red zone), taking the following action may reduce oreliminate the problem.
1. Turn off the air conditioner.
2. Reduce highway speed.
3. Select a lower gear when going uphill.
4. While in stop and go traffic, place the gear selection in park or neutral and idle the engine at a higher speed.

3-3
IN CASE OF EMERGENCY
SD060A1-E IN THE EVENT OF A PUNCTUREIf a puncture occurs whilst driving the vehicle:
1. Bring the car to rest as soon as it is safe to do so and with the minimum amount of braking required which will assist in main-taining the maximum amount of control. Thevehicle should be parked wherever possibleupon firm level ground to facilitate wheelchanging.
2. If the vehicle is creating a hazard and the road conditions do not permit the wheel to bechanged safely, assistance should be sought.
3. Passengers must not be allowed to remain inside the vehicle during wheel changing. Ifa puncture occurs whilst the vehicle is on a SD070A1-E CHANGING A FLAT TYRE
7. Proceed with caution until it is established
that the engine is operating normally. If the engine overheats repeatedly, the advice of aHyundai dealer should be sought.
CAUTION:Serious loss of coolant indicates there is aleak in the cooling system and this should bechecked as soon as possible by a Hyundaidealer.
It is of the utmost importance that care is exer-cised when changing road wheels. Ensure thatthe parking brake is set and that the gear shiftlever is in reverse (P, if the vehicle has automatictransaxle).
D040A01GK-EAT TEMPORARY SPARE TYREThe following instructions for the temporary spare tyre should be observed:
1. Check inflation pressure as soon as practical
after installing the spare tyre, and adjust to the specified pressure. The tyre pressure shouldbe periodically checked and maintained atthe specified pressure while the tyre is stored.
2. The spare tyre should only be used temporari-
ly and should be returned to the luggagecompartment as soon as the original tyre canbe repaired or replaced.
3. Continuous use at speeds of over 50 mph (80 km/h) is not recommended. 4. As the temporary spare tyre is specifically
designed for your car, it should not be used onany other vehicle.
5. The temporary spare tyre should not be used on any other wheels, nor should standardtyre, snow tyre, wheel covers or trim rings beused with the temporary spare wheel. If suchuse is attempted, damage to these items orother car components may occur.
6. The temporary spare tyre pressure should be checked once a month while the tyre is stored.
CAUTION:
o Do not use snow chains with your tempo- rary spare tyre.
o Do not use more than one temporary spare tyre at a time.
Spare Tyre Pressure
Type Size Inflation Pressure T125/70 R16420 kPa (60 psi)
motorway, the passengers should take ref- uge on the motorway embankment to avoidthe possibility of injury occurring should thevehicle be struck by other motorway traffic.
4. Wheel changing should be performed ac- cording to the following instructions.
D060A01GK

OWNER MAINTENANCE
6-6 WARNING: The oil being drained from the engine will behot. Care should be exercised to preventscalding.
4. When the oil has drained from the sump,
replace the drain plug using a new washer ensuring that the plug is not over tightened.
Tightening torque :
4.5 ~ 4.0 kgf.m (1.6/2.0L)4.5 ~ 3.5 kgf.m (2.7L)
5. Remove the oil filter by rotating counterclock- wise, using a proprietary oil filter removal toolif necessary. Note that the oil filter will containapproximately 0.5 litres of oil and this shouldbe collected in a suitable receptacle.
6. Install a new oil filter having smeared the sealing ring with clean oil and rotating clock-wise until the filter contacts the mounting andthen a further one half turn. Do not over-tighten. Tightening torque: 1.2 ~ 1.6 kgf.m.
7. Pour the specified quantity of the recom- mended oil into the engine and replace the filler cap. Start the engine and ensure that nooil leaks exist. Turn off the engine and after acouple minutes, recheck the oil level.
WARNING:Prolonged and repeated contact with usedengine oils may result in serious skin disor-ders including dermatitis and cancer. Avoidcontact with skin as far as possible and al-
G040A02GK-EAT ENGINE OIL AND FILTER REPLACEMENT The engine oil and filter must be changed at the time or mileage interval specified in the mainte-nance schedule. If the vehicle is operated undersevere or adverse conditions, the oil and filtermust be replaced more frequently.To replace the oil and filter, proceed as follows:
1. Ensure that the engine is at normal operating
temperature and park the vehicle on level ground with the parking brake securely ap-plied and the engine turned off.
2. Open the bonnet and remove the oil filler cap.
3. Prepare a suitable receptacle to collect the displaced oil and remove the drain plug fromthe sump.
G350A01A-GAT ENGINE OIL CONSUMPTION Function of engine oil Engine oil has the primary function of lubricating and cooling the inside of the engine. Engine oil consumption It is normal that an engine should consume some engine oil while normal driving. The cause of oilconsumption in a normal engine are as follows;
o Engine oil is used to lubricate pistons, piston
rings and cylinders. A thin film of oil is left on the cylinder wall whena piston moves downwards in the cylinder.High negative pressure generated during en-gine operation sucks some of the oil into thecombustion chamber.This oil with some oil of the cylinder wall isburned by the high temperature combustiongases during the combustion process.
o The engine oil consumption is strongly ef- fected by the viscosity and quality of oil,engine rpm and driving condition etc.More engine oil may be consumed undersevere driving conditions such as high speeds,frequent acceleration and deceleration, com-pared to normal driving.
G040A01GK
DOHC V6

OWNER MAINTENANCE 6-7
ways wash thoroughly after any contact. Keep used oils out of reach of children. It is illegalto pollute drains, water courses and soil. Useonly authorized waste collection facilitiesincluding civic amenity sites and garages forthe disposal of used oil and oil filters. If indoubt, contact the local authority for dis-posal instructions. SG050A1-E ENGINE COOLANT CHECKING AND REPLACING WARNING: Do not remove the radiator cap when the engine is hot, since the system is pressurizedand coolant may be ejected from the radiatorresulting in scalding. SG050B1-E Coolant recommendations
Only ethylene glycol based coolant with a corro- sion inhibitor suited to aluminium alloy enginecomponents should be used in the cooling sys-tem. No further additives or inhibitors should beused. The coolant specific gravity should bechecked as prescribed in the maintenance sched-ule to ensure adequate frost and corrosion pro-tection. In addition, the engine coolant must bereplaced at the specified interval since the corro-sion inhibitor properties deteriorate with time.It is important to note that whilst an increase in theconcentration of anti freeze gives an increase inthe level of frost protection, a solution which is inexcess of 65% anti freeze will result in reducedfrost protection and engine overheating. There-fore the recommended concentration of 50%should not be exceeded for general use.The use of methanol based anti freeze com-pounds may result in engine overheating and willinvalidate the vehicle warranty. NOTE: It is imperative that vehicles fitted with an airconditioning system have a coolant concen-tration of the recommended strength at alltimes. The use of the air conditioning systemwhen the cooling system is filled with wateronly will result in the heater matrix freezingand subsequently bursting.SG050C1-E Engine Coolant LevelThe engine coolant level may be observed through the side of the plastic coolant reservoir(expansion tank) when the engine is cold. If thelevel is below the "LOW" mark, add coolant of thecorrect concentration until the level is betweenthe "LOW" and "Full" marks. If the level fallsbelow the "LOW" mark on a regular basis despitebeing topped up, consult a Hyundai dealer. SG050D1-E To Change the Engine CoolantThe engine coolant should be changed at those intervals specified in the vehicle maintenanceschedule in Section 5. NOTE: Care should be taken to ensure that coolantis not allowed to spill onto the paintworksince the finish may become damaged. Ifcoolant spillage occurs, the affected areashould be rinsed thoroughly with water.
1. Park the vehicle on level ground and ensure
that the parking brake is firmly applied, and the engine allowed to cool.DO NOT ATTEMPT THIS OPERATIONWHILST THE ENGINE IS HOT SINCEBURN-ING OR SCALDING MAY RESULT.
2. Prepare a suitable receptacle to collect the displaced coolant and position this under theradiator drain tap.
HGK187

OWNER MAINTENANCE
6-8 CAUTION: Sparking plugs must only be cleaned usingpurpose designed equipment. Wire brushingmay damage the centre electrode insulatorcausing mis-firing to occur. Only the correctgrade of sparking plug should be used. Useof an incorrect grade may result in seriousengine damage.
3. With the heater temperature control set to the
"HOT" position, remove the radiator cap andopen the radiator drain tap.
4. When the engine coolant has drained com- pletely, close the drain tap ensuring that thisis not over tightened.
5. Prepare a suitable quantity of new engine coolant (refer to section 9) and pour this intothe radiator.
6. Start the engine with the radiator cap still removed and continue to add coolant as thelevel decreases as air is expelled from thesystem. When the level remains constant,replace the radiator cap and replenish thecoolant reservoir.
7. When the engine is hot, check to ensure that no coolant leaks are present.
WARNING:The cooling fan is controlled by engine cool-ant temperature and may sometimes operateeven when the engine is not running. Useextreme caution when working near the bladesof the cooling fan so that you are not injuredby a rotating fan blade. As the engine coolanttemperature decreases, the fan will automati-cally shut off. This is a normal condition. G060B02GK-EAT SPARKING PLUG REPLACEMENT This operation should only be performed when the engine is cold.
1. Remove the engine rocker cover.NOTE: It is recommended that the spark plug forEngine 2.7L should be changed by an autho-rized Hyundai dealer.
2. Remove plug lead from the sparking plug to
be replaced, pulling the lead by the rubber cap. (Pulling the lead may damage the carbonconductor).
3. Clean around the base of the plug to be removed, and install the plug socket ensuringthat the ceramic insulator does not becomedamaged. Turn the socket counterclockwiseto remove the plug.
YN60100A0.039 ~ 0.043 in. (1.0 ~ 1.1 mm)
0.039 ~ 0.043 in. (1.0 ~ 1.1 mm)
DOHC V6
HGK256

OWNER MAINTENANCE
6-10 15 seconds continuously or when the reser- voir is empty since damage to the washerpump will result. SG100A1-E MANUAL TRANSAXLE LUBRICANT The manual transaxle lubricant must be checkedand/or changed at the intervals specified in themaintenance schedule. Only those lubricantsspecified should be used in order to prevent gearshifting difficulties or transaxle damage. WARNING: The transaxle lubricant level should only bechecked when the engine is cold to precludethe possibility of personal injury by contactwith hot components. Recommended Oil
SG080A2-E WINDSCREEN WIPER BLADES
SG090A1-EWINDSCREEN WASHER RESERVOIRREPLENISHMENT
The wiper blades should be carefully inspected from time to time and cleaned to remove accu-mulations of road film or other debris. To cleanthe wiper blades and arms, use a clean spongeor cloth with a mild soap or detergent and water.If the wipers continue to streak or smear theglass, replace them with genuine Hyundai re-placement. CAUTION:
o Do not operate the wipers on dry glass since rapid wear and damage to thewindscreen glass may result.
o Keep the blade rubber out of contact with petroleum products such as engine oil,petrol etc. The level of windscreen washer fluid availableshould be checked on a daily basis. The level offluid will be visible through the side of the reser-voir. When the fluid is to be replenished, only aproprietary screen wash additive should be usedand in the concentration recommended by themanufacturer. The windscreen washer reservoirhas a total capacity of 3 litres. CAUTION: Engine coolant anti freeze must not be usedin the windscreen washer system since dam-age to the paintwork may result.Undiluted windscreen washer additive mustnot be allowed to come into contact with thepaintwork. If spillage occurs, flush the af-fected area immediately with water. Do notoperate the windscreen washer for more than
HGK217
HEF119
To ensure maximum filtration performance and continued engine performance, only genuineHyundai replacements should be used.
G110A01E
Filler plug
Drain plug