check engine light Hyundai Coupe 2003 Owner's Guide

CONTROLS AND EQUIPMENT
1- 62
B760A01E
The air conditioner filter is located in front of the blower uniit behind the glove box.It operates to decrease pollutants from enteringthe car and to filter the air. CAUTION:
o Replace the filter every 20,000 km (12,000 miles) or once a year. If the car is beingdriven in severe conditions such as dusty,rough roads, more frequent air filter in-spections and changes are required.
o When the air flow rate is decreased, it must be checked at an authorized dealer.
Evaporator coreBlower fan
Heater core
B760A03GK-EAT AIR CONDITIONER FILTER (IN FRONT OF BLOWER UNIT)
Outside air
Filter
Inside air
Inside air
Floor-Defrost Level
When selecting the "Floor-Defrost" mode, the indicator light will come on and the air will bedischarged through the windscreen defrostnozzle, the floor vents, side defroster nozzle,side ventilator. B980F01E-EAT Defrost Switch When the "Defrost" button is pressed, the " " mode will be automatically selected and the airwill be discharged through the windscreen de-frost vents. To assist in defrosting, the air condi-tioning will operate if ambient temperature ishigher than 38.3°F(3.5°C) and automatically turnsoff if the ambient temperature drops below38.3°F(3.5°C).
HGK012
B740D01A-AAT Operation Tips
o If the interior of the car is hot when you first get in, open the windows for a few minutes to expel the hot air.
o When you are using the air conditioning sys- tem, keep all windows closed to keep hot airout.
o When moving slowly, as in heavy traffic, shift to a lower gear. This increases engine speed,which in turn increases the speed of the airconditioning compressor.
o On steep grades, turn the air conditioner off to avoid the possibility of the engine over-heating.
o During winter months or in periods when the air conditioner is not used regularly, run theair conditioner once every month for a fewminutes. This will help circulate the lubricantsand keep your system in peak operatingcondition.

DRIVING YOUR HYUNDAI
2- 2 SC030A1-E
BEFORE STARTING THE ENGINE
Before you start the engine, you should always:
1. Look around the vehicle to be sure there are no flat tires, puddles of oil or water or other indications of possible trouble.
2. After entering the car, check to be sure the parking brake is engaged.
3. Check that all windows, and lights are clean.
4. Check that the interior and exterior mirrors are clean and in position.
5. Check your seat, seatback and head re- straint to be sure they are in their properpositions.
6. Close all the doors.
7. Fasten your seat belt and be sure that all other occupants have fastened theirs.
8. Turn off all lights and accessories that are not needed.
9. When you turn the ignition switch to "ON' check that all appropriate warning lights are operating and that you have sufficient fuel.
10.Check the operation of warning lights and all bulbs when key is in the "ON" position. o To start the engine, insert the ignition key
and turn it to the "START" position. Releaseit as soon as the engine starts. Do not holdthe key in the "START" position for more that15 seconds.
NOTE: For safety, the engine will not start if the shift lever is not in "P" or "N" Position (AutoT/A).
SC040A1-F
COMBINATION IGNITION SWITCH AND STEERING LOCK To Start the Engine
o If your Hyundai is equipped with a manual
transaxle, place the shift lever in neutral and depress the clutch pedal fully.
o If your Hyundai has an automatic transaxle, place the shift lever in "P" (park). SC050A2-E
KEY POSITIONS WARNING:
The engine must never be turned off and the key removed from the ignition key cylinderwhilst the vehicle is in motion since thesteering lock will operate and control of thevehicle will be lost. "START"
The engine is started in this position. It willcrank until you release the key. NOTE: Do not hold the key in the "START" position for more than 15 seconds.
"ON" When the key is at the "ON" position, the ignition and all accessories are available for use. If theengine is not running, the key should not be leftat this position since the battery will becomedischarged and damage to the ignition systemmay also result. For information regarding en-gine starting, refer to "STARTING THE EN-GINE". "ACC" When the ignition key is at the "ACC" position, the radio and other accessories may be used. "LOCK" The ignition key may only be inserted or removed at this position.
C040A01E
LOCK
ACC
ON
START

DRIVING YOUR HYUNDAI
2- 8 when you are driving down a long hill, slow down and shift to a lower gear. When you dothis, engine braking will help slow the car.
o Slow down before shifting to a lower gear. Otherwise, the lower gear may not be en-gaged.
o Always use the parking brake. Do not de- pend on placing the transaxle in "P" to keepthe car from moving.
o Exercise extreme caution when driving on a slippery surface. Be especially careful whenbraking, accelerating or shifting gears. On aslippery surface, an abrupt change in vehi-cle speed can cause the drive wheels tolose traction and the vehicle to go out ofcontrol.
WARNING:
o Avoid high cornering speeds.
o Do not make quick steering wheel move- ments, such as sharp lane changes or fast, sharp turns.
o Always wear your seat belts. In a collision crash, un unbelted personis significantly more likely to die than aperson wearing a seatbelt.
o The risk of rollover is greatly increased if you lose control of your vehicle at high-way speeds.
o Loss of control often occurs if two or more wheels drop off the roadway andthe driver oversteers to reenter the road-way. o In the event your vehicle leaves the road-
way, do not steer sharply. Instead, slowdown before pulling back into the travellanes.
o Never exceed posted speed limits. SC140A1-E EFFECTIVE BRAKING Braking system performance and friction mate- rial life are greatly affected by the driving styleadopted. The following suggestions are made toassist in achieving the best results from thebraking system.
o Anticipate the road and conditions ahead in order that heavy braking may be avoided.
o When descending long gradients, use the engine to assist in retarding the vehicle to minimize the possibility of brake fade occur-ring.
o When trailer towing, ensure that the trailer brakes function correctly and use enginebraking to assist the vehicle braking system.
o Use only genuine Hyundai replacement brake pads and shoes to ensure consistentfriction characteristics and wear rates.
o After driving through deep water (e.g. fording), the brakes may become wet andperformance reduced. Always check brakeefficiency after emerging from the water anddry the brakes by lightly depressing thebrake pedal several times whilst driving slow-ly.
C090I01L-GAT
CAUTION:
o Shift into "R" and "P" position only when the vehicle has completely stopped.
o Do not accelerate the engine in reverse or any of the forward positions with the brakes applied.
o Always apply the footbrake when shift- ing from "P" or "N", to "R", "D"position.
o Do not use the "P" (Park) position in place of the parking brake. Always setthe parking brake, shift the transaxle into"P" (Park) position and turn off the igni-tion when you leave the vehicle, evenmomentarily. Never leave the vehicleunattended while the engine is running.
o Check the automatic transaxle fluid level regularly, and add fluid as necessary.
C090N02O-AAT
Good Driving Practices
o Never move the gear selector lever from "P" or "N" to any other position with the acceler- ator pedal depressed.
o Never move the gear selector lever into "P" when the vehicle is in motion.
o Be sure the car is completely stopped be- fore you attempt to shift into "R".
o Never take the car out of gear and coast down a hill. This may be extremely hazard-ous. Always leave the car in gear whenmoving.
o Do not "ride" the brakes. This can cause them to overheat and malfunction. Instead,

DRIVING YOUR HYUNDAI
2- 10 C310D01O-AAT
Indicators and Warning The indicators should illuminate when the igni-
tion key is turned to ON or START but should go out after three seconds.
If the indicators do not illuminate, or the TCS or
TCS-OFF indicator does not go out after 3seconds, have it checked by an authorizeddealer.
Should there be any unusual conditions in the
device while driving, TCS-OFF indicator illumi-nates as a warning.
If TCS-OFF indicator illuminates, pull your car
to a safe place and stop the engine. Then, start the engine again to check if the
TCS-OFF indicator goes out.
If the indicator remains lit even after the engine
has been started, have your car checked by anauthorized Hyundai dealer. effect of brake control and indicates noth-ing unusual.
3) When the engine starts, a click is heard from the engine compartment; however,this is only the sound of traction controlbeing checked.
4) When moving out of the mud or fresh snow, pressing the accelerator pedal maynot cause the engine speed to increasedue to TCS operation. NOTE:
1) When the TCS-OFF indicator illuminates,
traction control is automatically deacti- vated for safety.
2) This warning function is not provided when the driver selects the TCS-OFFmode.
SC150A1-F DRIVING FOR ECONOMY You can save fuel and get more miles from your car if you follow these suggestions:
o Drive smoothly. Accelerate at a moderate rate. Don't make "jack-rabbit" starts or full- throttle shifts and maintain a steady cruisingspeed. Don't race between stoplights. Try toadjust your speed to that of the other trafficso you don't have to change speeds unnec-essarily. Avoid heavy traffic whenever possible. Al- ways maintain a safe distance from othervehicles so you can avoid unnecessary brak-ing. This also reduces brake wear.
o Drive at a moderate speed. The faster you drive, the more fuel your car uses. Driving ata moderate speed, especially on the high-way, is one of the most effective ways toreduce fuel consumption.
o Don't "ride" the brake or clutch pedal. This can increase fuel consumption and alsoincrease wear on these components. In ad-dition, driving with your foot resting on thebrake pedal may cause the brakes to over-
C310B01O-AAT
TCS ON/OFF Mode When the TCS is running, the TCS indicator
light in the instrument cluster will blink. If you turn the system off by pressing the TCS
switch, the TCS-OFF indicator light will comeon and stay on. In the TCS-OFF mode, theSLIP control will be deactivated. Adjust youdriving accordingly. To turn the system backon, press the switch again. The TCS-OFF indi-cator light should go off.
NOTE:
1) The TCS mode will automatically be turned ON after the engine is turned offand restarted.
2) When the traction control system is op- erating properly, you can feel a slightpulsation in the vehicle. This is only the
CAUTION: When the TCS indicator blinks, SLIP control
has been activated. It also means that the road is slippery or your car is acceleratingexcessively. In this situation, gently releasefoot pressure from the accelerator pedaland maintain moderate speed.
WARNING: Traction control is only a driving aid; all
normal precautions for driving in inclement weather and on slippery road surfacesshould be observed.

DRIVING YOUR HYUNDAI 2- 11
heat, which reduces their effectiveness and may lead to more serious consequences.
o Take care of your tires. Keep them inflated to the recommended pressure. Incorrect infla-tion, either too much or too little, results inunnecessary tire wear. Check the tire pres-sures at least once a month.
o Be sure that the wheels are aligned cor- rectly. Improper alignment can result fromhitting curbs or driving too fast over irregularsurfaces. Poor alignment causes faster tirewear and may also result in other problemsas well as greater fuel consumption.
o Keep your car in good condition. For better fuel economy and reduced maintenancecosts, maintain your car in accordance withthe maintenance schedule in Section 5. Ifyou drive your car in severe conditions,more frequent maintenance is required (seeSection 5 for details).
o Keep your car clean. For maximum service, your car should be kept clean and free ofcorrosive materials. It is especially impor-tant that mud, dirt, ice, etc. not be allowed toaccumulate on the underside of the car. Thisextra weight can result in increased fuelconsumption and also contribute to corro-sion.
o Travel lightly. Don't carry unnecessary weight in your car. Weight is an enemy of good fueleconomy.
o Don't let the engine idle longer than neces- sary. If you are waiting (and not in traffic),turn off your engine and restart only whenyou're ready to go. o Remember, your car does not require ex-
tended warm-up. As soon as the engine isrunning smoothly, you can drive away. Invery cold weather, however, give your en-gine a slightly longer warm-up period.
o Don't "lug" or "over-rev" the engine. Lugging is driving too slowly in too high a gearresulting in the engine bucking. If this hap-pens to you, shift to a lower gear. Over-revving is racing the engine beyond its safe limit. This can be avoided by shifting atthe recommended speeds.
o Use your air conditioning sparingly. The air conditioning system is operated by the en-gine power so your fuel economy is reducedwhen you use it.
SC160A1-F
SMOOTH CORNERING
Avoid braking or gear changing in corners,
especially when roads are wet. Ideally, cornersshould always be taken under gentle accelera-tion. If you follow these suggestions, tire wearwill be held to a minimum.
SC170A1-E
WINTER MOTORING The onset of winter conditions subject motor
vehicles to greater operating demands. There-fore, the following suggestions will assist inmaintaining peak performance and reliabilityduring these periods: ZC170B1-E
Electrical System
Winter conditions impose severe demands uponvehicle electrical systems, particularly the charg-ing circuit. The battery condition and perfor-mance along with the alternator performanceand drive belt condition should be checked priorto the onset of winter. ZC170C1-E
Anti-freeze/Corrosion inhibitor The cooling system must always contain an Ethylene-Glycol based anti-freeze solution. Thesystem is filled during manufacture with solu-tion of the correct strength which should bechecked before the onset of winter and adjust- ed or changed as required. NOTE: The anti-freeze solution contains a corro- sion inhibitor to prevent degradation of thealuminum castings contained within theengine. Therefore, never, drain the systemand refill with water only. In addition, anti-freeze solution must ALWAYS be used in vehicles fitted with air conditioning,to prevent the heater matrix from freezing andsubsequently bursting with the refrigeration sys-tem in use.

DRIVING YOUR HYUNDAI
2- 14
Coupling point
HGK260
View from below the vehicle YC200E1-E Trailer or Vehicle Towing Tips
1. Before towing, check towbar hitch and safe-
ty cable connections as well as proper oper- ation of the trailer running lights, brake lights,and turn signals.
2. Always drive your vehicle at a moderate speed (Less than 60mph).
3. Trailer towing requires more fuel than nor- mal conditions.
4. To maintain engine braking efficiency, do not tow a trailer with the transaxle engagedin an overdrive gear.
5. Always secure items in the trailer to prevent load shift while driving.
6. Check the condition and air pressure of all tires on the trailer and your car. Low tirepressure can seriously affect the handling.Also check the spare tire.
7. The vehicle/trailer combination is more af- fected by crosswind and buffeting. When being passed by a large vehicle, keep a constant speed and steer straight ahead.If there is too much wind buffeting, slowdown to get out of the other vehicle's airturbulence.
8. When parking your car and trailer, especial- ly on a hill, be sure to follow all the normalprecautions. Turn your front wheel into thecurb, set the parking brake firmly, and putthe transaxle in 1st or Reverse (manual) orPark (automatic). In addition, place wheelchocks at each of the trailer's tires.
o The maximum permissible static vertical
load on the coupling device :
o The maximum permissible overhang of the coupling point : 38.98 in.(990 mm)
1.6 L
2.0/2.7 L 110(50) 132(60)
Lbs.(kg)
NOTE:
o The total gross vehicle weight with trailer must not exceed the Gross Vehicle Weight Rating (GVWR) shown on the vehicleidentification plate (see page 8-1). Thetotal gross vehicle weight is the com-bined weight of the vehicle, driver, allpassengers and their luggage, cargo,hitch, trailer nose weight and other op-tional equipment.
o The front or rear axle weight must not exceed the Gross Axle Weight Rating(GAWR) shown on the vehicle identifica-tion plate (see page 8-1). it is possiblethat your towing package does not ex-ceed the GVWR but exceeds the GAWR.Improper trailer loading and/or too muchluggage in the boot can overload the rearaxle. Redistribute the load and check theaxle weight again. Maximum
Towable Weight
Trailer
1,212(550)
2,645(1,200) 3,086(1,400)
Lbs.(kg)
With Brake Type1.6 L
2.0/2.7 L
Without Brake Type

DRIVING YOUR HYUNDAI 2- 15
9. If the trailer has electric brakes, start your
vehicle and trailer moving, and then apply the trailer brake controller by hand to besure the brakes are working. This lets youcheck your electrical connection at the sametime.
10. During your trip, check occasionally to be sure that the load is secure, and that thelights and any trailer brakes are still working.
11. Avoid jerky starts, sudden acceleration or sudden stops.
12. Avoid sharp turns and rapid lane changes.
13. Avoid holding the brake pedal down too long or too frequently. This could cause the brakes to overheat, resulting in reduced brakingefficiency.
14. When going down a hill, shift into a lower gear and use the engine braking effect. When ascending a long grade, downshift the transaxle to a lower gear and reduce speedto reduce chances of engine overloadingand/or overheating.
15. If you have to stop while going uphill, do not hold the vehicle in place by pressing on theaccelerator. This can cause the automatictransaxle to overheat. Use the parking brakeor footbrake. NOTE: When towing check transaxle fluid more
frequently.
CAUTION:If overheating should occur when towing,
(temperature gauge reads near red zone), taking the following action may reduce oreliminate the problem.
1. Turn off the air conditioner.
2. Reduce highway speed.
3. Select a lower gear when going uphill.
4. While in stop and go traffic, place the gear selection in park or neutral and idle the engine at a higher speed.

IN CASE OF EMERGENCY
3-2 4. Check to see if the water pump drive belt is
missing. If it is not missing, check to see that it is tight. If the drive belt seems to be satisfac-tory, check for coolant leaking from the radia-tor, hoses or under the car. (If the air condi-tioning had been in use, it is normal for coldwater to be draining from it).
WARNING:Whilst the engine is running, keep hands andclothing away from moving parts such as thefan and drive belts to prevent injury.
5. If the water pump drive belt is broken or coolant is leaking out, stop the engine imme- diately and call the nearest Hyundai dealerfor assistance.
WARNING:Do not remove the radiator cap when theengine is hot since steam and boiling watermay be ejected from the radiator resulting inburns or scalding.
6. If the cause of the overheating cannot be found, wait until the engine temperature has returned to normal. Then, if coolant has beenlost, carefully remove the radiator cap andadd water to bring the fluid level in the reser-voir up to the base of the radiator fill opening.Fill the coolant expansion tank to the halfwaymark.
WARNING:Motor vehicle batteries contain sulphuric acidand emit hydrogen gas. Protective clothingshould be worn and care exercised to preventthe acid from coming into contact with skin orclothing and the vehicle. Naked lights shouldnot be permitted in the vicinity of the battery.Care should be exercised to prevent sparksoccurring during connection. If acid acciden-tally comes into contact with skin or eyes, theaffected area should immediately be flushedwith copious amounts of water and medicalassistance sought.
1. Ensure that the booster battery is 12 volt type.
If the booster battery is installed in another vehicle, ensure that the two vehicles are nottouching.
2. Turn off all unnecessary electrical equipment in both vehicles.
3. Ensure that the engine of the vehicle provid- ing the jump start is running prior to connec-tion of the jump cables.
4. Connect the red jump cable to the positive (+) terminal of the booster battery and the otherend to the positive (+) terminal of the dis-charged battery.
5. Attach the black jump cable to the negative (-) terminal of the booster battery, and theother end to a ground point within the enginecompartment of the vehicle with the flat bat-tery. Do not connect to the negative batteryterminal of the flat battery since sparks maybe generated with the subsequent risk ofexplosion. 6. Raise the booster vehicle engine speed to
2,000 r.p.m. and start the engine of the vehi-cle with the flat battery.
7. Remove jump cables in the reverse order of installation (black cable first).
CAUTION:If the jump cable is incorrectly installed, dam-age to the vehicle electrical system may oc-cur, in particular the electronic componentssuch as the Fuel Injection system computerand the Automatic Transaxle computer. Thebattery must never be disconnected whilstthe engine is running. SD040A1-E IF THE ENGINE OVERHEATSIf the temperature gauge indicates overheating:
1. Pull off the road and stop as soon as it is safe to do so.
2. Place the gear selector lever in "P" (auto- matic), or neutral (manual transaxle) and set the parking brake. If the air conditioning is on,turn it off.
3. If coolant is running out under the car or steam is coming out from under the bonnetstop the engine. Do not open the bonnet untilthe coolant has stopped running or the steam-ing has stopped. If there is no visible loss ofcoolant and no steam, leave the engine run-ning and check to be sure the engine coolingfan is operating.If the fan is not running, turn the engine off.

OWNER MAINTENANCE
6-4
SG020B1-E DAILY OPERATING CHECKSThe following items should be checked on a daily basis or whenever the vehicle is refuelled, which-ever occurs sooner.
o Engine oil level.
o Engine coolant level.
o Power steering fluid level.
o Brake fluid level.
o Windscreen washer fluid level.
o Battery condition.
o Tyre condition and pressures.
o Operation and cleanliness of all lighting equip-
ment.
o Windscreen wiper and washer operation.
o Horn operation.
o Warning lamp operation.
o Adjustment and cleanliness of mirrors.
o Seat and seat belt adjustment and operation.
o Fluid leakage. The vehicle must not be driven if the daily oper- ating checks indicate that any item of equipmentrelated to the safety or roadworthiness of thevehicle is not functioning correctly. SG030A1-E ENGINE OILThe correct engine oil level is of paramount importance. An excessively high or low oil levelmay result in irreparable damage being sus-tained by the engine. The engine oil level must bechecked on a daily basis or whenever the vehicleis refuelled, whichever occurs sooner.In addition, it is imperative that only an approvedgrade and specification of oil is used to avoid thepossibility of serious engine damage and prema-ture wear. The use of "budget price" oil is a falseeconomy that must be avoided if the maximumreliability and useful life is to be obtained from thevehicle.
SG030B02GK-E Recommended Oil A multi grade oil having a specification which meets A.P.I. specification of SH, SG or above isrecommended. The oil viscosity should be se-lected according to the operating environment ofthe engine by means of the table shown below.The engine oil recommendations are complete inthemselves and the use of additives is neitherrequired nor recommended. The use of engineoil additives may result in invalidation of thevehicle warranty.
SSA6030B°C °F
-25-13 20W-40 20W-50
15W-40 15W-50
10W-30
10W-40 10W-50
5W-40
5W-30
5W-2040
104
20 68
1050
032
-15 5 -10-14
1.6 DOHC 2.7 L V6

OWNER MAINTENANCE
6-12 SG120A1-E BRAKE SYSTEM CHECKING CAUTION: Correct operation of the braking system is essential to the safe operation of the vehicleand therefore, any maintenance operationsother than those listed below should be en-trusted to a Hyundai dealer. SG120C2-E Brake Fluid Recommendations Only brake fluid conforming to DOT 3 or DOT 4 specifications or higher may be used in thebraking system. Care should be taken to ob-serve the instructions and precautions printedupon the container. SG120D1-E Brake Fluid LevelThe fluid level in the brake fluid reservoir should be checked periodically. The level should bebetween the "MIN" and "MAX" marks on the sideof the reservoir. If the level is at or below the"MIN" mark, fluid should be added having care-fully cleaned the area surrounding the reservoircap to ensure that dirt is not allowed to enter thesystem. It should be borne in mind that the brakefluid level will decrease slightly as the frictionlinings of the pads and shoes become worn andthat this is a normal condition.
higher mark. If additional fluid is required, thisshould be poured into the transaxle through thedipstick tube with the aid of a suitable funnel. WARNING: The cooling fan is controlled by engine cool-ant temperature and may sometimes operateeven when the engine is not running. Useextreme caution when working near the bladesof the cooling fan so that you are not injuredby a rotating fan blade. As the engine coolanttemperature decreases, the fan will automati-cally shut off. This is a normal condition.
CAUTION:The automatic transaxle unit is a precisionengineered assembly and correct operationis dependant upon the exclusion of dirt andlint from the unit. Therefore, it is imperativethat only lint free cloth (eg nylon) is used forwiping the dipstick and that the area aroundthe dipstick is thoroughly clean prior to levelchecking or adding fluid. Fluid Capacity The total fluid capacity of the transaxle unit is 7.8 litres.
HGK174-D
Fluid level should be within this range
HGK249
ÎÎ