ABS Hyundai Creta 2016 User Guide

6-18
What to do in an emergency
6. Loosen the wheel lug nuts counterclockwise one turn each in the
order shown above, but do not
remove any lug nuts until the tire
has been raised off of the ground. 7. Place the jack at the front (1) or
rear (2) jacking position closest to
the tire you are changing. Place
the jack at the designated loca
tions under the frame. The jacking
positions are plates welded to the
frame with two tabs and a raised
dot to index with the jack.
OGC064005OGS065004
Jack location
To reduce the possibility of injury,
be sure to use only the jack pro
vided with the vehicle and in the
correct jack position; never use
any other part of the vehicle for
jack support.
WARNING

7-56
Maintenance
Wheel replacement
When replacing the metal wheels for
any reason, make sure the new
wheels are equivalent to the original
factory units in diameter, rim width
and offset.
Replacing tires
To reduce the chance or serious
or fatal injuries from an accident
caused by tire failure or loss of
vehicle control:
•Replace tires that are worn,
show uneven wear, or are dam
aged. Worn tires can cause loss
of braking effectiveness, steer
ing control, and traction.
•Do not drive your vehicle with
too little or too much pressure in
your tires. This can lead to
uneven wear and tire failure.
•When replacing tires, never mix
radial and biasply tires on the
same car. You must replace all
tires (including the spare) if mov
ing from radial to biasply tires.
(Continued)
(Continued)
WARNING •Using tires and wheel other than
the recommended sizes could
cause unusual handling charac
teristics and poor vehicle con
trol, resulting in a serious acci
dent.
•Wheels that do not meet
HYUNDAI's specifications may
fit poorly and result in damage to
the vehicle or unusual handling
and poor vehicle control.
•The ABS works by comparing
the speed of the wheels. Tire
size can affect wheel speed.
When replacing tires, all 4 tires
must use the same size original
ly supplied with the vehicle.
Using tires of a different size can
cause the ABS (Antilock Brake
System) and ESC (Electronic
Stability Control) to work irregu
larly. (if equipped)
A wheel that is not the correct size
may adversely affect wheel and
bearing life, braking and stopping
abilities, handling characteristics,
ground clearance, bodytotire
clearance, snow chain clearance,
speedometer and odometer cali
bration, headlight aim and bumper
height.
WARNING

7-72
Maintenance
ITEMNameSymbolFuse RatingCircuit Protected
FUSE
POWER
OUTLET POWER
OUTLET
R R20APower Outlet Rear
STARTSTART10APCU/ECU, Inhibitor Switch, Clutch Pedal Assy,Start Relay, Start Inhibitor Relay
SENSORS10AD4FC, D4FB : Fuel HTR Relay, Fuel Water Sensor
ENGE10AAirflow Sensor(D4FB), Smart key Control Module, ECU/PCU(G4FC,D4FC,D4FB)
ABS10AABS/ ESC Control Module, Rheostat & ESC Switch, Engine Room Diagnosis Connector
AIRBAG 10AAirbag Control Unit
CLUSTERCLUSTER10AInstrument Cluster
* G4FC : Gamma 1.6 (Gasoline), D4FC : UII 1.4 (Diesel), D4FB : UII 1.6 (Diesel)

7-75
7
Maintenance
Engine Compartment Fuse Panel
ItemNameSymbolFuse RatingCircuit Protected
MULTIFUSEMDPS80AMDPS(Motor Power Steering)
ALTALT125A/150AG4FC (125A): Alternator, Battery, All Fuses connected to Alternator fuse
D4FC/D4FB (150A): Alternator, Battery, All Fuses connected to Alternator fuse
FUSE
ECU 2E210A/15AG4FC(10A): ECU (M/T), PCU(A/T)
D4FC(15A): CAM SNSR, Glow RLY, WGT,EGR Control Valve, Air Flow SNSR, IMMO
D4FB (15A): CAM SNSR, VGT Vacuum, IMMO
HEAD LAMPHIGH BEAM10AHead Lamp High Solenoid Relay (BiFunctional Type)
ABS 240AABS / ESC Control Module
ECU 4E425A/15AG4FC(25A): ECU (M/T), PCU(A/T)
D4FC(15A): Inlet Meter Valve,
D4FB(15A): Glow Plug Relay, Fuel Meter Unit
TCU 1625AD4FB: TCU(A/T)
B+540AInstrument Panel Fuse Block Fuse: FS01
ABS 140AABS / ESC Control Module, Engine Room Diagnosis
B+450AInstrument Panel Fuse Block Fuse: FS06, IPS1, IPS2, IPS3
* G4FC : Gamma 1.6 (Gasoline), D4FC : UII 1.4 (Diesel), D4FB : UII 1.6 (Diesel)

7-80
Maintenance
Headlight (Low/High)
1. Open the hood.
2. Remove the headlight bulb cover by turning it counterclockwise.
3. Disconnect the headlight bulb socketconnector.
4. Unsnap the headlight bulb retain ing wire by depressing the end
and pushing it upward.
5. Remove the bulb from the head light assembly. 6. Install a new headlight bulb and
snap the headlight bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlight bulb socket connector.
8. Install the headlight bulb cover by turning it clockwise.
Turn signal light
1. Remove the turn signal light bulbcover by turning it counterclock
wise.
2. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
3. Insert a new bulb by inserting it into the socket and rotating it until
it locks into place.
4. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
5. Install the turn signal light bulb cover by turning it clockwise.
OGS075050
Turn signal lightParking
(Position) light
Headlight

7-81
7
Maintenance
Parking (Position) light
1. Remove the socket from the
assembly by pulling it straight out.
2. Remove the bulb from the socket by pulling it out.
3. Insert a new bulb by inserting it into the socket.
4. Install the socket in the assembly by pushing it in.
Front fog light bulb replacement
1. Remove the under cover by rotating the screws and bolts.
2. Reach your hand into the back of the front bumper.
3. Disconnect the power connector from the socket.
4. Remove the bulbsocket from the housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the housing.
5. Install the new bulbsocket into the housing by aligning the tabs on
the socket with the slots in the
housing. Push the socket into the
housing and turn the socket clock
wise.
6. Connect the power connector to the socket.
7. Reinstall the front bumper under cover.
Type B
(1) Headlight (Low/High)
(2) Parking (Position) light
(3) Front turn signal light
(4) Static bending light
(5) Front fog light (if equipped)
(6) Daytime running light (if equipped)
OGS075055

7-83
7
Maintenance
6. Install a new headlight bulb and
snap the headlight bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlight bulb socket connector.
8. Install the headlight bulb cover by turning it clockwise.
Information
BiFunction projection
headlamp
This headlamp is bifunction type that
switches the low beam to high or the
high beam to low using solenoid sys
tem. So, the moving sound may be
heard when the headlamp switches
the low beam to high or the high beam
to low and it does not indicate mal
function of the headlamp.
Turn signal light
1. Remove the turn signal light bulb cover by turning it counterclock
wise.
2. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
3. Insert a new bulb by inserting it into the socket and rotating it until
it locks into place.
4. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
5. Install the turn signal light bulb cover by turning it clockwise.
Front fog light bulb replacement
1.Remove the under cover by rotating the screws and bolts.
2.Reach your hand into the back of the front bumper.
3.Disconnect the power connector from the socket.
4.Remove the bulbsocket from the housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the housing.
5.Install the new bulbsocket into the housing by aligning the tabs on the
socket with the slots in the hous
ing. Push the socket into the hous
ing and turn the socket clockwise.
6.Connect the power connector to the socket.
7.Reinstall the front bumper under cover.
i

7-85
7
Maintenance
Outside light
1. Open the tailgate
2. Loosen the light assembly retaining screws with a crosstip screw
driver.
3. Remove the rear combination light assembly from the body of the
vehicle. 4. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
5. Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
Inside lamp
Backup light/Tail light
1. Turn off the engine.
2. Open the tailgate.
3. Remove the service cover using a flatblade screwdriver.
OGC074046
Stop/Tail
Turn signal
Back upTailOGC074026
OGC074027
OGC074028
OGC074029

4.Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
5.Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
6.Insert a new bulb into the socket.
7.Install the socket into the assembly by aligning the tabs on the socket
with the slots on the assembly and
turning the socket clockwise.Rear fog lamp (if equipped)
1.Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
2.Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
3.Insert a new bulb in the socket.
4.Reinstall the light assembly to the body of the vehicle.
High mounted stop light
If the light does not operate, we rec
ommend that the vehicle be checked
by an authorized HYUNDAI dealer.
7-86
Maintenance
OGC074031

Interior light bulb replacement1. Using a flatblade screwdriver,gently pry the lens from the interi
or lamp housing.
2. Remove the bulb by pulling it straight out.
3. Install a new bulb in the socket.
4. Align the lens tabs with the interior lamp housing notches and snap
the lens into place.
Use care not to dirty or damage lens,
lens tab, and plastic housings.
NOTICE
7-88
Maintenance
Prior to working on the Interior
lamps, ensure that the “OFF” but
ton is depressed to avoid burning
your fingers or receiving an elec
tric shock.
WARNING
■Map lamp (if equipped)
■Room lampOGS075047/OGS075049/OGS075048
■Luggage room lamp