brake Hyundai Creta 2016 Manual Online

7-31
7
Maintenance
Brake hoses and lines
Visually check for proper installation,
chafing, cracks, deterioration and
any leakage. Replace any deteriorat
ed or damaged parts immediately.
Brake fluid
Check brake fluid level in the brake
fluid reservoir. The level should be
between "MIN" (Minimum) and
"MAX" (Maximum) marks on the side
of the reservoir. Use only hydraulic
brake fluid conforming to DOT 3 or
DOT 4 specification.
Parking brake
Inspect the parking brake system
including the parking brake pedal
and cables.
Brake discs, pads, calipers and
rotors
Check the pads for excessive wear,
discs for run out and wear, and
calipers for fluid leakage.
Suspension mounting bolts
Check the suspension connections
for looseness or damage. Retighten
to the specified torque.
Steering gear box, linkage &
boots/lower arm ball joint
With the vehicle stopped and engine
off, check for excessive freeplay in
the steering wheel.
Check the linkage for bends or dam
age. Check the dust boots and ball
joints for deterioration, cracks, or
damage. Replace any damaged
parts.
Steering gear box, linkage &
boots/lower arm ball joint
With the vehicle stopped and engine
off, check for excessive freeplay in
the steering wheel.
Check the linkage for bends or dam
age. Check the dust boots and ball
joints for deterioration, cracks, or
damage. Replace any damaged
parts.
Drive shafts and boots
Check the drive shafts, boots and
clamps for cracks, deterioration, or
damage. Replace any damaged
parts and, if necessary, repack the
grease.
Air conditioning refrigerant
(if equipped)
Check the air conditioning lines and
connections for leakage and dam
age.

7-37
7
Maintenance
BRAKE/CluTCh FluId (IF EquIPPEd)
Checking the brake/clutch fluid
level
Check the fluid level in the reservoir
periodically. The fluid level should be
between MAX (Maximum) and MIN
(Minimum) marks on the side of the
reservoir. Before removing the reservoir cap
and adding brake/clutch fluid, clean
the area around the reservoir cap
thoroughly to prevent brake/clutch
fluid contamination. If the level is low,
add fluid to the MAX (Maximum)
level. The level will fall with accumu
lated mileage. This is a normal con
dition associated with the wear of the
brake linings and/or clutch disc (ifequipped).
If the fluid level is excessively low, we
recommend that the system be
checked by an authorized HYUNDAI
dealer.
Use only the specified brake/clutch
fluid. (Refer to “Recommended lubricants or capacities” in chapter 8.)
Information
Before removing the brake/clutch fil
ter cap, read the warning on the cap.
Information
Clean filler cap before removing. Use
only DOT3 or DOT4 brake/clutch
fluid from a sealed container.i
i
Loss of brake fluid
In the event the brake system
requires frequent additions of
fluid, we recommend that the sys
tem be inspected by an authorized
HYUNDAI dealer.
WARNING
OGS075006
OGS075006L
■ Right Hand Drive
■Left Hand Drive

7-38
Maintenance
Do not allow brake/clutch fluid to
contact the vehicle's body paint, as
paint damage will result.
Brake/clutch fluid, which has been
exposed to open air for an extended
time should never be used as its
quality cannot be guaranteed. It
should be properly disposed. Don't
put in the wrong kind of fluid. A few
drops of mineralbased oil, such as
engine oil, in your brake/clutch sys
tem can damage brake/clutch system
parts.
NOTICE
Brake/clutch fluid
When changing and adding
brake/clutch fluid, handle it care
fully. Do not let it come in contact
with your eyes. If brake/clutch fluid
come in contact with your eyes,
immediately flush them with a
large quantity of fresh tap water.
Have your eyes examined by a
doctor as soon as possible.
WARNING

7-39
7
Maintenance
WAShER FluId
Checking the washer fluid level
Check the fluid level in the washer
fluid reservoir and add fluid if neces
sary. Plain water may be used if
washer fluid is not available.
However, use washer solvent with
antifreeze characteristics in cold cli
mates to prevent freezing. Do not use engine coolant or
antifreeze in the washer fluid reser
voir.
Checking the parking brake
Check the stroke of the parking
brake by counting the number of
“clicks’’ heard while fully applying it
from the released position.
Also, the parking brake alone should
securely hold the vehicle on a fairly
steep grade. If the stroke is more or
less than specified, we recommend
that the system be inspected by an
authorized HYUNDAI dealer.
Stroke : 6~8 “clicks’’ at a force of 20
kg (44 lbs, 196 N).
NOTICE
OGS075007
OGS075008
•Engine coolant can severely
obscure visibility when sprayed
on the windshield and may
cause loss of vehicle control or
damage to paint and body trim.
•Windshield Washer fluid agents
contain some amounts of alco
hol and can be flammable under
certain circumstances. Do not
allow sparks or flame to contact
the washer fluid or the washer
fluid reservoir. Damage to the
vehicle or occupants could
occur.
•Windshield washer fluid is poi
sonous to humans and animals.
Do not drink and avoid contact
ing windshield washer fluid.
Serious injury or death could
occur.
WARNING
PARKING BRAKE

7-54
Maintenance
Tire rotation
To equalize tread wear, it is recom
mended that the tires be rotated
every 12,000 km (7,500 miles) or
sooner if irregular wear develops.
During rotation, check the tires for
correct balance.
When rotating tires, check for uneven
wear and damage. Abnormal wear is
usually caused by incorrect tire pres
sure, improper wheel alignment, out
ofbalance wheels, severe braking or
severe cornering. Look for bumps or
bulges in the tread or side of tire.
Replace the tire if you find either of
these conditions. Replace the tire if
fabric or cord is visible. After rotation,
be sure to bring the front and rear tire
pressures to specification and check
lug nut tightness.
Refer to “Tire and wheels” in chapter
8.Disc brake pads should be inspected
for wear whenever tires are rotated.
Information
Rotate radial tires that have an asym
metric tread pattern only from front
to rear and not from right to left.i
CBGQ0706
CBGQ0707
CBGQ0707A
Without a spare tire
With a fullsize spare tire (if equipped)
Directional tires (if equipped)
•Do not use the compact spare
tire for tire rotation.
•Do not mix bias ply and radial
ply tires under any circum
stances. This may cause unusu
al handling characteristics that
could result in death, severe
injury, or property damage.
WARNING

7-56
Maintenance
Wheel replacement
When replacing the metal wheels for
any reason, make sure the new
wheels are equivalent to the original
factory units in diameter, rim width
and offset.
Replacing tires
To reduce the chance or serious
or fatal injuries from an accident
caused by tire failure or loss of
vehicle control:
•Replace tires that are worn,
show uneven wear, or are dam
aged. Worn tires can cause loss
of braking effectiveness, steer
ing control, and traction.
•Do not drive your vehicle with
too little or too much pressure in
your tires. This can lead to
uneven wear and tire failure.
•When replacing tires, never mix
radial and biasply tires on the
same car. You must replace all
tires (including the spare) if mov
ing from radial to biasply tires.
(Continued)
(Continued)
WARNING •Using tires and wheel other than
the recommended sizes could
cause unusual handling charac
teristics and poor vehicle con
trol, resulting in a serious acci
dent.
•Wheels that do not meet
HYUNDAI's specifications may
fit poorly and result in damage to
the vehicle or unusual handling
and poor vehicle control.
•The ABS works by comparing
the speed of the wheels. Tire
size can affect wheel speed.
When replacing tires, all 4 tires
must use the same size original
ly supplied with the vehicle.
Using tires of a different size can
cause the ABS (Antilock Brake
System) and ESC (Electronic
Stability Control) to work irregu
larly. (if equipped)
A wheel that is not the correct size
may adversely affect wheel and
bearing life, braking and stopping
abilities, handling characteristics,
ground clearance, bodytotire
clearance, snow chain clearance,
speedometer and odometer cali
bration, headlight aim and bumper
height.
WARNING

7-70
Maintenance
ITEMNameSymbolFuse RatingCircuit Protected
FUSE
BRAKE
SWITCH10AStop Lamp Switch, Smart Key Control Module
HTD IND10AA/C Control Module (Manual, Auto), G4FC : ECU(MT), PCU(AT)
BLOWER110AAC Control Module (Auto)
REAR WIPER10ARear Wiper Motor, Rear Wiper Relay
SPARE10A
SPARE15A
MEMORY10ADigital Clock, Body Control Module, AC Control Module (Auto, Manual), Cluster,
Outside Mirror Folding , OBD
MULTIMEDIA20AAudio
SPARE10A
C_LIGHTER20ACigar lighter (Export only)
INTERIOR LP 10ARoom Lamp, MAP Lamp, Luggage Lamp
BLOWER SIGNAL210AAC Control Module (Manual)
SPARE20A
* G4FC : Gamma 1.6 (Gasoline), D4FC : UII 1.4 (Diesel), D4FB : UII 1.6 (Diesel)

7-78
Maintenance
lIGhT BulBS
Consult an authorized HYUNDAI
dealer to replace most vehicle light
bulbs. It is difficult to replace vehicle
light bulbs because other parts of the
vehicle must be removed before you
can get to the bulb. This is especially
true for removing the headlight
assembly to get to the bulb(s).
Removing/installing the headlight
assembly can result in damage to
the vehicle.Information
After heavy driving, rain or washing
headlight and taillight lenses could
appear frosty. This condition is caused
by the temperature difference between
the lamp inside and outside.
This is similar to the condensation on
your windows inside your vehicle dur
ing the rain and doesn’t indicate a
problem with your vehicle. If the
water leaks into the lamp bulb circuit
ry, we recommend that the system be
checked by an authorized HYUNDAI
dealer.
Be sure to replace the burnedout
bulb with one of the same wattage
rating. Otherwise, it may cause dam
age to the fuse or electric wiring sys
tem.
NOTICE
i
Prior to replacing a light, depress
the foot brake, move the shift lever
into the P (Park, for automatic
transaxle vehicle) or neutral (for
manual transaxle vehicle), apply
the parking brake, place the igni
tion switch in the LOCK/OFF posi
tion, and take the key with you
when leaving the vehicle to avoid
sudden movement of the vehicle
and to prevent possible electric
shock.
Be aware the bulbs may be hot
and may burn your fingers.
WARNING

7-89
7
Maintenance
APPEARANCE CARE
Exterior care
Exterior general caution
It is very important to follow the label
directions when using any chemical
cleaner or polish. Read all warning
and caution statements that appear
on the label.
Finish maintenance
Washing
To help protect your vehicle’s finish
from rust and deterioration, wash it
thoroughly and frequently at least
once a month with lukewarm or cold
water.
If you use your vehicle for offroad
driving, you should wash it after each
offroad trip. Pay special attention to
the removal of any accumulation of
salt, dirt, mud, and other foreign
materials. Make sure the drain holes
in the lower edges of the doors and
rocker panels are kept clear andclean.
Insects, tar, tree sap, bird droppings,
industrial pollution and similar
deposits can damage your vehicle’s
finish if not removed immediately.
Even prompt washing with plain
water may not completely remove all
these deposits. A mild soap, safe for
use on painted surfaces, may beused.
After washing, rinse the vehicle thor
oughly with lukewarm or cold water.
Do not allow soap to dry on the finish. •Do not use strong soap, chemical
detergents or hot water, and do not
wash the vehicle in direct sunlight
or when the body of the vehicle is
warm.
•Be careful when washing the side
windows of your vehicle.
Especially, with highpressure
water, water may leak through the
windows and wet the interior.
•To prevent damage to the plastic
parts and lamps, do not clean with
chemical solvents or strong deter
gents.
NOTICE
Wet brakes
After washing the vehicle, test the
brakes while driving slowly to see if
they have been affected by water. If
braking performance is impaired,
dry the brakes by applying them
lightly while maintaining a slow for
ward speed.
WARNING

7-91
7
Maintenance
Brightmetal maintenance
• To remove road tar and insects,use a tar remover, not a scraper or
other sharp object.
• To protect the surfaces of bright metal parts from corrosion, apply a
coating of wax or chrome preser
vative and rub to a high luster.
• During winter weather or in coastal areas, cover the bright metal parts
with a heavier coating of wax or
preservative. If necessary, coat the
par ts with noncorrosive gasoli
neeum jelly or other protective
compound.
Underbody maintenance
Corrosive materials used for ice and
snow removal and dust control may
collect on the underbody. If these
materials are not removed, acceler
ated rusting can occur on the under
body parts such as the fuel lines,
frame, floor pan and exhaust system,
even though they have been treated
with rust protection.
Thoroughly flush the vehicle under
body and wheel openings with luke
warm or cold water once a month,
after offroad driving and at the end
of each winter. Pay special attention
to these areas because it is difficult
to see all the mud and dirt. It will do
more harm than good to wet down
the road grime without removing it.
The lower edges of the doors, rocker
panels, and frame members have
drain holes that should not clog with
dirt; trapped water in these areas can
cause rusting.
After washing the vehicle, test the
brakes while driving slowly to see
if they have been affected by
water. If braking performance is
impaired, dry the brakes by apply
ing them lightly while maintaining
a slow forward speed.
WARNING