heating HYUNDAI ELANTRA 2022 Owners Manual

Instrument Cluster
4-6
Engine coolant temperature gauge
OCN7040008
OCN7040009
„Type A

„Type B
This gauge indicates the temperature
of the engine coolant when the ignition
switch is in the ON position.
NOTICE
If the gauge pointer moves beyond
the normal range area toward the "H"
position, it indicates overheating that
may damage the engine.
Do not continue driving with an
overheated engine. If your engine
overheats, refer to "If the Engine
Overheats" in chapter 7.
WARNING
Never remove the radiator cap or
reservoir cap when the engine is hot.
The engine coolant is under pressure
and could severely burn. Wait until the
engine is cool before adding coolant to
the reservoir.
Fuel gauge
OCN7040010
OCN7040011
„Type B 
„Type A
This gauge indicates the approximate
amount of fuel remaining in the fuel tank.
Information

[The fuel tank capacity is given in
chapter 2.

[The fuel gauge is supplemented by
a low fuel warning light, which will
illuminate when the fuel tank is nearly
empty.

[On inclines or curves, the fuel gauge
pointer may fluctuate or the low fuel
warning light may come on earlier than
usual due to the movement of fuel in
the tank.

Instrument Cluster
4-22
Wiper
OAD048579N
This indicator displays which wiper speed
is selected using the wiper control.
Heated Steering Wheel turned off (if
equipped)
This message is displayed if you turn off
the heated steering wheel.
For more details, refer to “Heated
Steering Wheel” in chapter 5.
Low washer fluid (if equipped)
This warning message is displayed if
the washer fluid level in the reservoir is
nearly empty.
Have the washer fluid reservoir refilled.
Low fuel
This warning message is displayed if the
fuel tank is almost out of fuel.
When this message is displayed, the low
fuel level warning light in the cluster will
come on.
It is recommended to look for the nearest
fueling station and refuel as soon as
possible.
Engine Overheated (if equipped)
This warning message is displayed
when the engine coolant temperature
is above 248°F (120°C). This means that
the engine is overheated and may be
damaged.
If your vehicle is overheated, refer to
“Overheating” in chapter 8.
Check headlight (if equipped)
This warning message is displayed if the
headlamps are not operating
properly.
In addition, if a specific lamp(turn signal
lamp etc.) is not operating properly, the
warning message according to a specific
lamp (turn signal lamp etc.) is displayed.
A corresponding bulb may need to be
replaced.
Make sure to replace the burned out
bulb with a new one of the same wattage
rating.

5
High Beam Assist (HBA) ............................................................................. 5-72Detecting sensor (Front view camera) ...................................................................5-72
Function settings .....................................................................................................5-72
Function operation ..................................................................................................5-73
Function malfunction and limitations ....................................................................5-73
Interior Lights ............................................................................................... 5-75Interior lamp AUTO cut ...........................................................................................5-75
Front lamps ..............................................................................................................5-75
Rear lamp ................................................................................................................ 5-76
Luggage compartment lamp ................................................................................. 5-77
Vanity mirror lamp ................................................................................................... 5-77
Welcome system .................................................................................................... 5-78
Wipers and Washers .................................................................................... 5-79
Windshield Wipers ................................................................................................. 5-79
Windshield Washers ...............................................................................................5-80
Manual Climate Control System ................................................................. 5-81Heating and Air Conditioning ................................................................................ 5-82
System operation ...................................................................................................5-88
System Maintenance .............................................................................................5-90
Automatic Climate Control System ............................................................ 5-92Automatic heating and air conditioning ............................................................... 5-93
Manual heating and air conditioning .................................................................... 5-94
System operation ................................................................................................. 5-100
System Maintenance ............................................................................................5-102
Windshield defrosting and defogging ...................................................... 5-104Manual climate control system ........................................................................... 5-104
Automatic climate control system .......................................................................5-105
Defogging logic ................................................................................................... 5-106
Auto defogging system (only for automatic climate control system) ............... 5-107
Defroster ............................................................................................................... 5-108
Climate control additional features .......................................................... 5-109
Sunroof inside air recirculation ........................................................................... 5-109
Auto comfort control (for driver’s seat) .............................................................. 5-109
Automatic ventilation ........................................................................................... 5-109
Storage compartment ................................................................................ 5-110
Center console storage ......................................................................................... 5-110
Glove box ............................................................................................................... 5-110
CN7 HMA 5.indd 5-22020-12-03 9:20:41

05
5-21
Remote Start with Digital Key
• When the shift lever of your vehicle
is in P (Park) and all of the doors
including trunk and hood is locked
and the vehicle is off, press the Door
Lock button in the Hyundai Digital
Key app then press the Remote Start
button within 4 seconds.
You can confirm the engine is on if the
hazard warning lights blinks two times
and the chime sounds.
• If you want to turn off the engine,
press Remote Engine Stop. Air
Conditioner / Heating system
maintains the same status as when
you last used the vehicle.
• Unless you put the registered digital
key(smartphone) on the interior
authentication pad (wireless charger)
when the remote start function is on,
the engine will turn off.
• If you do not get into the vehicle
within 10 minutes after the engine
turns on, the vehicle will turn off.
For more information, refer to the Engine
Start/Stop button in chapter 6.
Vehicle information Display
The digital key application displays
the vehicle information such as
driving or door conditions through the
communication with the vehicle.
• How to check : Select the vehicle
what you want to check and touch
the vehicle image, then vehicle
information display page will be
shown.
• Contents : accumulated odometer,
latest fuel economy, driving range,
fuel remaining, tire pressure, doors
lock/unlock status and last data
updated time.
ÃDisplayed vehicle data could be
differed from the current vehicle
condition.
ÃFor more information, please refer to
the ‘Tutorial’ on your Digital key app.6PDUWSKRQHFKDQJH$SSGHOHWLRQ
If you change your smartphone or delete
the Hyundai Digital Key App, please refer
to the following to set up your Digital
Key:
Smartphone Change/ Reset
If you change or reset the smartphone,
the registered digital key in your previous
smartphone may not be used. Please
refer to following procedure to use the
digital key.
1. Install the digital key application and
log in.
2. If you are the owner, retry the Digital
key save process.
3. If you are the sharer, need to re-share
the key from owner.
App delete & reinstall/ Delete App data
You can re-download the digital key from
the server and follow these procedures.
1. Reinstall the application and log in.
2. Input the PIN number for user
verification.
3. If PIN is correct, digital key data
will be re-downloaded to your
smartphone and you can use it
without any further registration or
sharing.
Smartphone operability with Digital Key
The digital key application may not be
available to older type smartphones.
Please check the available smartphone
models with your dealer. NFC antenna
position on the smartphone can be
confirmed on each smartphone’s manual
or contact to customer service center of
the smartphone manufacturer.
CN7 HMA 5.indd 5-212020-12-03 9:20:45

Convenient Features
5-82
Heating and Air Conditioning
1. Start the engine.
2. Set the mode to the desired position.
To improve the effectiveness of
heating and cooling, select the mode
according to the following:
- Heating:
- Cooling:
3. Set the temperature control to the
desired position.
4. Set the air intake control to fresh
mode or recirculation mode position.
5. Set the fan speed control to the
desired speed.
6. If air conditioning is desired, turn the
air conditioning system on.
When starting the vehicle in cold weather
a more efficient way to heat the passen-
ger compartment is to do the following.
- Turn off or lower the blower, right
after starting the engine.
• Engine temperature is still low and the
air flow from the heater is still cold.
- After a few minutes of engine warm
up, turn on or set the fan to a higher
level and adjust the temperature
setting towards hot.
CN7 HMA 5.indd 5-822020-12-03 9:21:02

Convenient Features
5-88
System operation
Ventilation
1. Select the Face Level mode.
2. Set the air intake control to fresh
mode.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
Heating
1. Select the Floor Level mode.
2. Set the air intake control to fresh
mode.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
5. If desired, turn the air conditioning ON
with the temperature control knob set
to heat in order to dehumidify the air
before it enters into the cabin.
If the windshield fogs up, select the Floor
& Defrost
mode or rotate the mode
selecting knob to the Defrost
mode.
2SHUDWLRQ7LSV
• To help keep dust or unpleasant fumes
from ent
ering the vehicle through the
ventilation system, temporarily set the
air intake control to the recirculation
mode. Be sure to return the control
to fresh mode position when the
irritation has passed to keep fresh air
in the vehicle. This will help keep the
driver alert and comfortable.
• To help prevent interior fog on the
windshield, set the air intake control
to fresh mode and fan speed to
the desired position, turn on the
air conditioning system, and adjust
the temperature control to desired
temperature.
Air conditioning
HYUNDAI Air Conditioning Systems are
filled with R-1234yf refrigerant.
1. Start the vehicle.
2. Push the air conditioning button
3. Select the Face Level
mode.
4. Set the air intake control to
Recirculation mode temporarily to
allow the cabin to cool quickly. When
the desired temperature in the cabin
is reached, change the air intake
control back to Fresh mode.
5. Adjust the fan speed control and
temperature control to maintain
maximum comfort.
CN7 HMA 5.indd 5-882020-12-03 9:21:04

Convenient Features
5-90
$LUFRQGLWLRQLQJV\VWHPRSHUDWLRQWLSV
• If the vehicle has been parked in
direct sunlight during hot weather,
open the windows for a short time
to let the hot air inside the vehicle
escape.
• After sufficient cooling has been
achieved, switch back from
recirculation mode to fresh mode.
• To help reduce moisture inside of
the windows on rainy or humid
days, decrease the humidity inside
the vehicle by operating the air
conditioning system with the windows
and sunroof closed.
• During air conditioning system
operation, you may occasionally
notice a slight change in engine speed
as the air conditioning compressor
cycles. This is a normal system
operation characteristic.
• Use the air conditioning system
every month only for a few minutes
to ensure maximum system
performance.
• When using the air conditioning
system, you may notice clear water
dripping (or even puddling) on the
ground under the passenger side of
the vehicle. This is a normal system
operation characteristic.
• If you operate the air conditioner
excessively, the difference between
the temperature of the outside air and
that of the windshield could cause
the outer surface of the windshield to
fog up, causing loss of visibility. In this
case, set the mode selection button to
the
position and set the fan speed
control knob to the lowest speed
setting.
System Maintenance
Cabin air filter
OIK047401LOIK047401L[A] : Outside air, [B] : Recirculated air
[C] : Cabin air filter, [D] : Blower
[E] : Evaporator core, [F] : Heater core
The cabin air filter is installed behind
the glove box. It filters the dust or other
pollutants that enter the vehicle through
the heating and air conditioning system.
Have the cabin air filter replaced by an
authorized HYUNDAI dealer according to
the maintenance schedule. If the vehicle
is being driven in severe conditions such
as dusty or rough roads, more frequent
cabin air filter inspections and changes
are required.
If the air flow rate suddenly decreases,
the system should be checked at an
authorized HYUNDAI dealer.
Information
• 5HSODFHWKHILOWHUDFFRUGLQJWRWKH
0DLQWHQDQFH6FKHGXOH
• ,IWKHFDULVEHLQJGULYHQLQVHYHUH
FRQGLWLRQVVXFKDVGXVW\URXJK
URDGVPRUHIUHTXHQWFDELQDLUILOWHU
LQVSHFWLRQVDQGFKDQJHVDUHUHTXLUHG
• :KHQWKHDLUIORZUDWHVXGGHQO\
GHFUHDVHVZHUHFRPPHQGWKDWWKH
V\VWHPEHFKHFNHGE\DQDXWKRUL]HG
+<81'$,GHDOHU
CN7 HMA 5.indd 5-902020-12-03 9:21:05

05
5-93
Automatic heating and air
conditioning
OCN7050112OCN7050112
1. Press the AUTO button
The modes, fan speeds, air intake and
air-conditioning will be controlled
automatically according to the
temperature setting you select.
OCN7050113OCN7050113
You can control the blower strength in
three stages by pushing the AUTO button
during automatic operation.
- HIGH : Provide rapid air conditioning
and heating with strong blower
- MEDIUM : Provide air conditioning
and heating with medium strength
blower
- LOW : Is suitable for drivers that prefer
lower air speedsWhen you select the temperature to HI
or LO in AUTO mode, the fan speed is set
to ‘HIGH’.
„„Driver’s seatDriver’s seat„„Passenger’s seatPassenger’s seat
OCN7050114OCN7050114
2. Turn the temperature control knob
to set the desired temperature. If
the temperature is set to the lowest
setting (Lo), the air conditioning
system will operate continuously.
• To turn the automatic operation off,
select any button of the following:
- Mode selection button
- Front windshield defroster button
(Press the button one more time
to deselect the front windshield
defroster function. The ‘AUTO’ sign
will illuminate on the information
screen once again.)
- Fan speed control toggle switch
The selected function will be
controlled manually while other
functions operate automatically.
• For your convenience and overall
system efficiency, use the AUTO
button and set the temperature to
72°F (22°C).
CN7 HMA 5.indd 5-932020-12-03 9:21:06

Convenient Features
5-94
OCN7050133OCN7050133
Information
1HYHUSODFHDQ\WKLQJQHDUWKHVHQVRUWR
HQVXUHEHWWHUFRQWURORIWKHKHDWLQJDQG
FRROLQJV\VWHP
Manual heating and air
conditioning
The heating and cooling system can be
controlled manually by pushing buttons
other than the AUTO button. In this case,
the system works sequentially according
to the order of buttons selected. When
pressing any button except the AUTO
button while using automatic operation,
the functions not selected will be
controlled automatically.
1. Start the engine.
2. Set the mode to the desired position.
To improve the effectiveness of
heating and cooling, select the mode
according to the following:
- Heating:
- Cooling:
3. Set the temperature control to the
desired position.
4. Set the air intake control to fresh
mode.
5. Set the fan speed control to the
desired speed.
6. If air conditioning is desired, turn the
air conditioning system on.
7. Press the AUTO button in order to
convert to full automatic control of
the system.
CN7 HMA 5.indd 5-942020-12-03 9:21:06

Convenient Features
5-98
OCN7050117OCN7050117
$GMXVWLQJWKHGULYHUDQGSDVVHQJHUVLGH
WHPSHUDWXUHHTXDOO\
• Press the “SYNC” button to adjust
the driver and passenger side
t
emperature equally.
• The passenger side temperature will
be set to the same temperature as the
driver side temperature.
• Turn the driver side temperature
control knob. The driver and
passenger side temperature will be
adjusted equally.
• If you rotate the passenger’s
temperature control knob, the SYNC
button is off and the passenger
side temperature can be operated
individually.
$GMXVWLQJWKHGULYHUDQGSDVVHQJHUVLGH
WHPSHUDWXUHLQGLYLGXDOO\
Press the “SYNC” button again to
adjust the driv
er and passenger side
temperature individually. The button
indicator will turn off.
7HPSHUDWXUHFRQYHUVLRQ
If the battery has been discharged or
disconnected, the temperature mode
display will reset to Centigrade.
To change the temperature unit from °C
to °F or °F to °C :
- Automatic climate control system
Press the AUTO button for 3 seconds
while pressing the OFF button.
- Instrument clusterAutomatic climate
control system
Go to User Settings
Ÿ Other
Ÿ
Temperature Unit.
The temperature unit on both the
cluster LCD display and the climate
control screen will change.
Air intake control
5HFLUFXODWHGDLUSRVLWLRQ
With the recirculated air
position selected, air from the
passenger compartment will
be drawn through the heating
system and heated or cooled
according to the function
selected.
2XWVLGHIUHVKDLUSRVLWLRQ
With the outside (fresh) air
position selected, air enters
the vehicle from outside and
is heated or cooled according
to the function selected.
CN7 HMA 5.indd 5-982020-12-03 9:21:08