stop start HYUNDAI ELANTRA N 2022 Owner's Manual

04
4-17
Electronic Stability Control
(ESC) OFF Indicator Light
This indicator light illuminates:
• When you set the Engine Start/Stop butt
on to the ON position.
- It illuminates for approximately 3 seconds and then goes off.
• When you deactivate the ESC system by pressing the ESC OFF button.
For more information, refer to
“Electronic Stability Control (ESC)” in
chapter 6.
Immobilizer Indicator Light
(with smart key)
(if equipped)
This indicator light illuminates for up to
30 seconds:
When the vehicle detects the smart key
in the v
ehicle with the Engine Start/Stop
button in the ACC or ON position.
- Once the smart key is detected, you can start the engine.

- The indicator light goes off after
starting the engine.
This indicator light blinks for a few seconds:
When the smart key is not in the vehicle.
- If the smart key is not detected, you cannot start the engine.
This indicator light illuminates for 2
seconds and goes off:
If the smart key is in the vehicle and the
E
ngine Start/Stop button is ON, but the
vehicle cannot detect the smart key.
In this case, have the vehicle inspected
by an authorized HYUNDAI dealer.
This indicator light blinks:
When there is a malfunction with the
immobiliz
er system.
In this case, have the vehicle inspected
by an authorized HYUNDAI dealer.
CN7 N HMA 4.indd 4-17 2021-09-14  9:32:37

Instrument Cluster4-18
Turn Signal Indicator Light
This indicator light blinks:
When you operate the turn signal
indica
tor stalk.
If any of the following occur, there may be
a malfunction with the turn signal system.

- The turn signal indicator light
illuminates but does not blink

- The turn signal indicator light blinks
rapidly

- The turn signal indicator light does not
illuminate at all
If any of these conditions occur, have
your vehicle inspected by an authorized
HYUNDAI dealer.
For more details, refer to “High Beam
Assist (HBA)” in chapter 5.
Exterior Light Warning Light
(if equipped)
This warning light illuminates:
• When one of the exterior bulbs (headlamp, DRL, turn signal lamp,
s

top lamp, etc) is not operating
properly. One of the bulbs may need
to be replaced.
Information
Make sure to replace the burned out bulb
with a new one of the same wattage rating.
LED headlight warning light
(if equipped)
This warning light illuminates:
• When you set the Engine Start/Stop butt
on to the ON position.
- The LED headlight warning light illuminates for approximately 3
seconds and then goes off.
• Whenever there is a malfunction with the LED headlight.
If this occurs, have your vehicle
inspected by an authorized HYUNDAI
dealer.
NOTICE
Continuous driving with the LED
Headlight warning light on or blinking
can reduce LED headlight life.
High Beam Indicator Light
This indicator light illuminates:
• When the headlights are on and in the high beam position.
•

When the turn signal lever is pulled
into the Flash-to-Pass position.
Light ON Indicator Light
This indicator light illuminates:
When the tail lights or headlamps are on.
CN7 N HMA 4.indd 4-18 2021-09-14  9:32:37

04
4-19
Low Beam Indicator Light (if
equipped)
This indicator light illuminates:
• When the headlamps are on.
High Beam Assist indicator
light
This indicator light illuminates:
• When the High Beam is on with the light s
witch in the AUTO light position.
• If your vehicle detects oncoming or preceding vehicles, High Beam Assist
system will switch the high beam to
low beam automatically.
For more information, refer to "High
Beam Assist (HBA)" in chapter 5.
Forward Safety Warning
Light
This warning light illuminates:
• When you set the ignition switch or E
ngine Start/Stop button to the ON
position.
- It illuminates for approximately 3 seconds and then goes off.
• When there is a malfunction with Forward Collision-Avoidance Assist. In
this case, have your vehicle inspected
by an authorized dealer of HYUNDAI.
For more information, refer to "Forward
Collision-Avoidance Assist (FCA)" in
chapter 7.
Lane Safety Indicator Light
This indicator light illuminates:
• [Green] When you activate Lane K
eeping Assist by pressing the Lane
Safety button and all of the function
operating conditions are satisfied.
• [White] When Lane Keeping Assist operating conditions are not satisfied
or when the sensor does not detect
the lane line.
• [Yellow] When there is a malfunction with Lane Keeping Assist.
In this case, have your vehicle inspected
by an authorized HYUNDAI dealer.
For more information, refer to "Lane
Keeping Assist (LKA)" in chapter 7.
Cruise Indicator Light
This indicator light illuminates:
• When Cruise Control is enabled.
F
or more details, refer to “Cruise
Control (CC)” in chapter 6.
SPORT Mode Indicator Light
(if equipped)
This indicator light illuminates:
• When you select “SPORT” mode as driv
e mode.
For more details, refer to “Drive Mode
Integrated Control System” in chapter
6.
CN7 N HMA 4.indd 4-19 2021-09-14  9:32:38

04
4-21
LCD Display Messages
Key not in vehicle (for smart key
system)
This warning message is displayed if the
smart key is not in the vehicle when you
open or close door in the ACC position or
ON position. The warning sound is heard
when you close door without a smart key
in vehicle.
When attempting to start the vehicle
always have the smart key with you.
Key not detected (for smart key
system)
This warning message is displayed if the
smart key is not detected when you press
the Engine Start/Stop button.
Press START button with key (for
smart key system)
This warning message is displayed if you
press the Engine Start/Stop button while
the warning message “Key not detected”
is displayed.
At this time, the immobilizer indicator
light blinks.
Press START button again (for smart
key system)
This message is displayed if you were
unable to start the vehicle when the
Engine Start/Stop button was pressed.
If this occurs, attempt to start the engine
by pressing the Engine Start/Stop button
again.
If the warning message appears each
time you press the Engine Start/Stop
button, have your vehicle inspected by
an authorized HYUNDAI dealer.
Low Key Battery (for smart key
system)
This warning message is displayed if the
battery of the smart key is discharged
while changing the Engine Start/Stop
button to the OFF position.
Shift to P (for smart key system and
dual clutch transmission)
This warning message is displayed if you
try to turn off the engine without the
shift lever in P (Park) position.
At this time, the Engine Start/Stop button
turns to the ACC position (If you press
the Engine Start/Stop button once more,
it will turn to the ON position).
Press brake pedal to start engine (for
smart key system and dual clutch
transmission)
This warning message is displayed if the
Engine Start/Stop button changes to
the ACC position twice by pressing the
button repeatedly without depressing
the brake pedal.
You can start the vehicle by depressing
the brake pedal.
Press clutch pedal to start engine
(for smart key system and manual
transmission)
This warning message is displayed if the
Engine Start/Stop button is in the ACC
position twice by pressing the button
repeatedly without depressing the clutch
pedal.
Depress the clutch pedal to start the
engine.
Press START button again (for smart
key system)
This message is displayed if you were
unable to start the vehicle when the
Engine Start/Stop button was pressed.
If this occurs, attempt to start the engine
by pressing the Engine Start/ Stop button
again.
If the warning message appears each
time you press the Engine Start/Stop
button, have your vehicle inspected by
an authorized HYUNDAI dealer.
CN7 N HMA 4.indd 4-212021-09-14  9:32:38

Instrument Cluster4-22
Check BRAKE SWITCH fuse (for
smart key system and dual clutch
transmission)
This warning message is displayed if the
brake switch fuse is disconnected.
You need to replace the fuse with a new
one. If that is not possible, you can start
the engine by pressing the Engine Start/
Stop button for 10 seconds in the ACC
position.
Shift to P or N to start engine (for
smart key system and dual clutch
transmission)
This warning message is displayed if you
try to start the engine with the shift lever
not in the P (Park) or N (Neutral) position.
Information
You can start the engine with the shift
lever in the N (Neutral) position. But, for
your safety, we recommend that you start
the engine with the shift lever in the P
(Park) position.
Battery discharging due to external
electrical devices (if equipped)
This message is displayed if the battery
voltage is weak due to any non-factory
electrical accessories (ex. dashboard
camera) while parking. Be careful that
the battery is not discharged.
If the warning message appears after
removing the non-factory electrical
accessories, have the vehicle inspected
by an authorized HYUNDAI dealer.
Door, Hood, Trunk open indicator
OCN7N041017LOCN7N041017L
This warning is displayed indicating
which door, or hood, or trunk is open.
CAUTION
Before driving the vehicle, you should
confirm that the door/ hood/trunk is
fully closed. Also, check there is no
door/hood/ trunk open warning light or
message displayed on the instrument
cluster.
Sunroof open indicator (if equipped)
OCN7N041018LOCN7N041018L
This warning is displayed if you turn off
the engine when the sunroof is open.
Close the sunroof securely when leaving
your vehicle.
CN7 N HMA 4.indd 4-22 2021-09-14  9:32:39

Instrument Cluster4-28
OBC3N040026OBC3N040026
OBC3N040027OBC3N040027
Lap timer
(1) Best lap
(2) Curr
ent lap
To start (A)
Press the OK button shortly on the
s
teering wheel. The lap timer will start
counting the current lap (2).
To stop (B)
Press and hold the OK button for more
than 1 second on the s
teering wheel
while the lap timer is counting the
current lap (2).
OBC3N040028OBC3N040028
To reset (C):
Press and hold the OK button for more
than 1 second on the s
teering wheel
when the lap timer has stopped counting
the current lap (2).
To save laps:
Press the OK button shortly on the
s
teering wheel while the lap timer is
counting the current lap (2).
From best lap (1) to No.4 lap (3) will be
displayed.
Press the OK button for more than 1
second on the steering wheel to reset the
lap. Then the driver can start a new lap.
Information
Lap timer can be activated regardless of
the mode settings (Drive mode or N mode).
NOTICE
If the N1(N2) button is set to 'Start
lap timer', the N2(N1) button is
automatically set to 'Stop & Reset lap
timer' from the infotainment system.
Then the driver can operate lap timer
using the N1/N2 buttons as the one pair.
For more details, please refer to the
infotainment system manual separately
supplied.
CN7 N HMA 4.indd 4-28 2021-09-14  9:32:48

04
4-33
2. Door
ItemsExplanation
Auto Lock• Enable on Shift: All doors will be automatically locked if the
automatic transmission/dual clutch transmission shift lever is
moved from the P (Park) position to the R (Reverse), N (Neutral), or
D (Drive) position. (Only when the engine is running)
• Enable on Speed: All doors will be automatically locked when the vehicle speed exceeds 9.3mph (15km/h).
• Disable : The auto door lock operation will be deactivated.
Auto Unlock • On Shift to P: All doors will be automatically unlocked if the
automatic transmission/dual clutch transmission shift lever is
moved to P (Park) position. (Only when the engine is running)
• On key out/Vehicle Off : All doors will be automatically unlocked. When the Engine Start/Stop button is set to the OFF position.
• Disable : The auto door unlock operation will be canceled.
Two Press Unlock
• Off: The two press unlock function will be deactivated. Therefore, all doors will unlock if the door unlock button is pressed.
• On: Only the driver’s door will unlock if the door unlock button is pressed. When the door unlock button is pressed again within 4
seconds, the remaining doors will unlock.
Smart TrunkTo activate or deactivate the smart trunk.
For more details, refer to “Smart trunk” in chapter 5.
3. Lights
Items Explanation
IlluminationTo adjust the illumination level.
- Level 1~20
One Touch
Turn Signal • Off: The one touch turn signal function will be deactivated.
• 3, 5, 7 Flashes: The turn signal indicator will blink 3, 5, or 7 times
when the turn signal lever is moved slightly.
For more details, refer to “Lighting” in chapter 5.
Headlight Delay• To activate or deactivate the headlamp delay function.
For more details, refer to “Lighting” in chapter 5.
High Beam Assist• To activate or deactivate High Beam Assist.
For more details, refer to “High Beam Assist (HBA)” in chapter 5.
CN7 N HMA 4.indd 4-33 2021-09-14  9:32:57

Instrument Cluster4-38
Type AType AType BType B
OTMA040014OTMA040014OOSN041027NOOSN041027N
Since refuel(l)ing
Trip distance (1), average fuel economy
(2), and t
otal driving time (3) after the
vehicle has been refueled are displayed.
To reset manually, press the OK switch
on the steering wheel for more than
1 second when ‘Since Refueling’ is
displayed.
Type AType AType BType B
OTMA040016OTMA040016OOSN041028NOOSN041028N
Accumulated info
Accumulated trip distance (1), average
fuel econom
y (2), and total driving time
(3) are displayed.
The information is accumulated starting
from the last reset.
To reset manually, press the OK switch
on the steering wheel for more than
1 second when ‘Accumulated Info’ is
displayed.
Information
The vehicle must be driven for a minimum
of 0.19 miles (300 meters) since the last
Engine Start/Stop button cycle before the
average fuel economy will be recalculated.
Digital speedometer
OTMA040018OTMA040018
This message shows the speed of the
vehicle.
CN7 N HMA 4.indd 4-38 2021-09-14  9:32:58

05
5-5
Even though you press the outside
door handle button, the doors will not
lock and the chime will sound for three
seconds if any of the following occur:
• The Smart Key is in the vehicle.
• The Engine Start/Stop button is in ACC or ON position.
• Any door except the trunk is open.
WARNING
Do not leave the Smart Key in your
vehicle with unsupervised children.
Unattended children could press the
Engine Start/ Stop button and may
operate power windows or other
controls, or even make the vehicle
move, which could result in serious
injury or death.
Unlocking your vehicle
(When the Two Press Unlock
feature is off)
Button typeButton type
OCN7050078OCN7050078
Touch sensor typeTouch sensor type
OCN7050093NOCN7050093N
1. Make sure you have the smart key in your possession.
2. Press the Door Unlock button (2) on the smart key, press the button on the
front door handle or touch the door
unlock sensor inside of the front door
handle to unlock the doors.
3. All of the doors will unlock. When the doors unlock, the hazard warning
lights will blink two times.
• The door handle button will only operate when the smart key is within
28~40 inches (0.7~1 m) from the
outside door handle.
• If you do not open the door after unlocking within 30 seconds, it will
return to the lock mode.
• If you unlocked the door with the door handle, the doors cannot be locked
with the sensor for up to 2 seconds.
CN7 N HMA 5.indd 5-5 2021-09-06  3:06:10

Convenience Features5-8
Start-up
You can start the engine without
inserting the key. For detailed
information refer to the Engine Start/
Stop button in chapter 6.
Information
If the smart key is not moved for some
time, the detection function for smart key
operation will pause. Lift the smart key to
activate the detection again.
NOTICE
To prevent damaging the smart key:
• Keep the smart key away from water
or any liquid and fire. If the inside
of the smart key gets damp (due to
drinks or moisture), or is heated,
internal circuit may malfunction and
may void the vehicle warranty.
• Avoid dropping or throwing the
smart key.
• Protect the smart key from extreme
temperatures.
NOTICE
Always have the smart key with you
when leaving the vehicle. If the smart
key is left near the vehicle, the vehicle
battery may be discharged.
Mechanical Key
If the Smart Key does not operate
normally, you can lock or unlock the door
by using the mechanical key.
OJSN048131 OJSN048131
Press and hold the release button (1) and
remove the mechanical key (2). Insert the
mechanical key into the key hole on the
door.
To reinstall the mechanical key, put the
key into the hole and push it until a click
sound is heard.
Loss of a Smart Key
A maximum of two smart keys can be
registered to a single vehicle. If you
happen to lose your smart key, it is
recommended that you immediately take
the vehicle and remaining key to your
authorized HYUNDAI dealer or tow the
vehicle, if necessary.
CN7 N HMA 5.indd 5-8 2021-09-06  3:06:10