warning light Hyundai Equus 2016 Manual PDF

Operating conditions
The BSD indicator will illuminate
when the BSD system switch is
pressed ON after turning the Engine
Start/Stop button ON.
When the vehicle speed exceeds 9.3
mph (15 km/h), the system will acti-
vate.
When you press the BSD switch
again, the indicator and the BSD sys-
tem will be turned OFF.
When the ignition switch is pressed
ON after engine turn-OFF, the BSD
system returns to the previous state.
When the BSD system is not used,
turn the BSD system OFF by press-
ing the switch.
When the BSD system is turned ON,
the warning light will illuminate for 3
seconds on the outside rearview mir-
ror.
Warning types
The system will activate as below.
1.The system is ON.
2.The vehicle speed is above 9.3mph (15 km/h).
3.Other vehicles are detected behind your vehicle.
When a vehicle is detected within the
system sensing range, a warning
light will illuminate on the outside
rearview mirror and the head-up dis-
play.
When a detected vehicle is out of the
warning range, the warning alarm
will be turned OFF according to driv-
ing conditions.
5-59
Driving your vehicle05
OVI055120N
1st stage

The second-stage alarm will activate
when:
1.The first-stage alarm is ON.
2.The turn signal is pressed ON,before changing the lanes.
When the second-stage alert is
active, a warning light will flash on
the outside rearview mirror and the
head up display, and an alarm will
sound.
When the turn signal switch is
pressed to the original position, the
second-stage alert will be deactivat-
ed.
Detecting sensor
The sensors are located inside of the
rear bumper.
Always keep the rear bumper clean
for the proper operation of the sys-
tem.
5-60
Driving your vehicle
OVI055130N
OVI055121N
OVI055122N
2nd stage

RCTA (Rear cross traffic alert)
When your vehicle drives backwards
after parking, the sensor detects any
approaching vehicles from the left
and right sides and gives information
to the driver.
Operating conditions
When you press the BSD switchwith the ignition ON, the BSD indi-
cator illuminates and the system
turns ON.
The system operates, when the driving speed is below 6.2 mph (10
km/h) with the shift lever in
R(Rear).
The RCTA sensing range is from 0.5m to 20m in accordance with
the directions. When the approach-
ing vehicle speed is from 2.5 mph
(4 km/h) to 22 mph (36 km/h) with-
in the sensing range, it will be
detected. However, the system
sensing range is varied in different
conditions. Always take a look
around the vehicle.
Warning type
When the sensor detects anyapproaching vehicles behind, the
warning light will flash on the out-
side rearview mirror with an warn-
ing alarm.
When an approaching vehicle behind is out of the sensing range,
when it drives away in the opposite
direction or when it drives slowly,
the warnings will be turned OFF.
The system may not normally operate due to certain factors.
Always take a look around your
vehicle.
❈ When the left- or right-side
bumper of your vehicle is blinded
by barriers or vehicles, the system
sensing performance may be
deteriorated.
5-62
Driving your vehicle
OVI055132NOVI055131N

The system may not properlyoperate, when the bumper is
replaced, or when a repair work
is done near the sensor.
The sensing range differs according to the roads width.
When the road is narrow, the
system may detect other vehi-
cles in the next lane.
On the contrary, when the road is wide, the system may not
detect other vehicles.
The system may be turn OFF due to the strong electromagnet-
ic waves.
Non-operating condition
Driver's Attention
The driver must be cautious in the
below situations, because the sys-
tem may not properly operate to
assist the driver.
- The vehicle drives on a curved roador through a tollgate.
- The sensor is polluted with rain, snow, mud, etc.
- The rear bumper, in which the sen- sor is located, is covered or blocked
with a foreign matter such as a
sticker, a bumper guard, a bicycle
stand, etc.
- The rear bumper is damaged, or the sensor is out of the original
default position.
- The vehicle height gets lower or higher due to heavy loading in a
trunk, abnormal tire pressure, etc.
- The vehicle drives in a bad weather such as heavy rain or snow.
- There is a fixed object near the vehicle, such as a guardrail.
- A huge amount of metal sub- stances are near the vehicle, such
as in a construction site.
- A big vehicle is near such as a bus or truck.
- A motorcycle or bicycle is near.
- A flat trailer like vehicle is near.
- When the other vehicle passes by very fast.
- When changing lanes.
- When going down or up a steep road where the height of the lane is differ-
ent.
NOTICE
5-63
Driving your vehicle05
The warning light on the out- side rearview mirror and the
head-up display will illumi-
nate whenever an approach-
ing vehicle behind is detected
by the system.
To avoid an accident, do not
pay too much attention to the
warnings, and do not neglect
to take a look around.
Drive safely even though the vehicle is equipped with the
BSD system. Do not rely sole-
ly on the system. Check the
road conditions before chang-
ing the lanes.
The system may not alert the
driver in some conditions.
Thus, take a look around.
WARNING

- When the other vehicle drives at therear very nearby or drives very close.
- When a trailer or carrier is installed.
- When the temperature of rear bumper is high.
- When the sensors are covered by the vehicle, wall and pillar of parking
lot.
- When your vehicle moves back, if the detected vehicle also moves back.
- If there is small things like shopping cart and baby carriage.
- If there is low height vehicle like sport vehicle.
- When the vehicle is close to your vehicle.
- When driving through a narrow road with many trees or bushes.
The warning light on the outsiderearview mirror may not alert thedriver, when:
- The outside rearview mirrors are
severely polluted
- The windows are severely polluted
- The windows are severely tinted.
This device complies with Part
15 of the FCC rules.
Operation is subject to the following
two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any inter- ference received, including inter-
ference that may cause undesired
operation.
5-64
Driving your vehicle

Hazard warning flasher
The hazard warning flasher serves
as a warning to other drivers to be
extremely cautious when approach-
ing, passing by or passing ahead.
It should be used when your vehicle
is under emergency repair, or when
your vehicle stops on the edge of a
roadway.
Press the flasher switch regardless
of the ignition switch position. The
flasher switch is on the switch panel
of the center consol. All turn signal
lights will simultaneously flash.
• The hazard warning flasher oper-ates, whether your vehicle is run-
ning or not.
The turn signals cannot be turned ON when the hazard flasher is ON.
Care must be taken to turn ON the hazard warning flasher, when tow-
ing your vehicle.
If the engine stalls at a cross-
road or a railroad crossing
If the engine stalls at a crossroad or
a railroad crossing, set the shift lever
in N(Neutral) and then push the
vehicle to a safe place.
If you have a flat tire while
driving
If a tire goes flat while driving:
1.Take your foot off the acceleratorand slow down the speed while
driving straight ahead. Do not
abruptly apply the brakes in an
attempt to pull over the vehicle, as
this may cause a loss of control.
When the driving speed gets suffi-
ciently lowered to stop the vehicle,
carefully apply the brake and pull
off the road. Drive away from the
road as far as possible and safely
park the vehicle in a safe and flat
place. When you are on a divided
highway, do not park the vehicle in
the median area between the two
directions.
2.When the vehicle is stopped, turn ON the emergency hazard flasher,
set the parking brake, and set the
shift lever in P(Park).
3.Have all occupants get out of the vehicle. Make sure they stay out of
the roadway.
4.When changing a flat tire, follow the instruction provided in the fol-
lowing part of this chapter.
R RO
O A
AD
D
W
W A
AR
RN
N I
IN
N G
G
6-2
What to do in an emergency
OVI045086N
I
IN
N
C
C A
A S
SE
E
O
O F
F
A
A N
N
E
E M
M E
ER
R G
G E
EN
N C
CY
Y
W
W H
HI
IL
L E
E
D
D R
RI
IV
V I
IN
N G
G

Always check the TPMS malfunction
telltale after replacing one or more
tires or wheels on your vehicle to
ensure that the replacement or alter-
nate tires and wheels allow the TPMS
to continue to function properly.
Information
If any of the followings happens, we
recommend that the system be
checked by an authorized EQUUS
dealer.
1. The low tire pressure telltale/TPMSmalfunction indicator does not illu-
minate for 3 seconds when the igni-
tion switch is turned ON or engine is
running.
2. The TPMS malfunction indicator remains ON after flashing for
approximately 1 minute.
3. The Low tire pressure position tell- tale remains ON.
Low tire pressure tell-
tale
Low tire pres-
sure position
telltale
When the TPMS malfunction indica-
tor illuminates with a warning mes-
sage on the LCD display, one or
more of your tires are significantly
under-inflated. The low tire pressure
position telltale pinpoints which tire is
significantly under-inflated with the
illumination of the corresponding
position light.
When the low tire pressure telltale
illuminates, immediately decrease
your driving speed, avoid hard cor-
nering and prepare for a longer stop-
ping distance. You should immediate-
ly stop the vehicle and check your
tires. Inflate the tires to the proper
pressure as indicated on the vehi-
cle’s placard or tire inflation pressure
label, which is on the right lower part
of the driver’s door sill.
When you cannot reach to a service
station, or when the tire cannot keep
the inflated air inside, replace the
under-inflated tire with the spare tire.
Until you repair or replace the under-
inflated tire, the low tire pressure tell-
tale remains ON, and the TPMS mal-
function indicator also remains ON
after 1-minute flashing (when the
vehicle is driven for approximately 20
minutes at a speed above 15.5 mph
(25 km/h)).
i
6-8
What to do in an emergency
OVI045740

Changing a tire with TPMS
When you have a flat tire, both of the
low tire pressure telltale and the low
tire position telltale will illuminate.
Immediately have the flat tire
repaired or replaced by an author-
ized EQUUS dealer.
The spare tire is not equipped with a
tire pressure monitoring sensor.
Thus, when replacing with the spare
tire, the low tire pressure telltale will
remain ON.
Also, the TPMS Malfunction Indicator
will illuminate after 1-minute flashing,
when the vehicle drives at a speed
above 15.5 mph (25 km/h) for
approximately 20 minutes.
When the tire equipped with a tire
pressure monitoring sensor is re-
inflated to the recommended level,
the low tire pressure telltale and
TPMS malfunction indicator will go
OFF for a few minutes.
When the indicator illumination does
not go OFF after a few minutes,
please visit an authorized EQUUS
dealer.Each wheel is equipped with a tire
pressure sensor, inside the tire and
behind the valve stem (except for the
spare tire). You must use the TPMS-
specific wheels. It is recommended
that you always have your tires serv-
iced by an authorized EQUUS deal-
er.
You cannot diagnose under-inflation
of a tire only with eyes. Always use a
tire pressure gauge of good quality to
measure the pressure level. Please
note that a heated tire (from being
driven) has higher pressure meas-
urement criteria than a cold tire.
A cold tire means the vehicle was
driven for less than 1 mile (1.6 km),
or was mostly idle for the last 3
hours.
Cool down the tire before measuring
the inflation pressure. Always make
sure that the tire is cold before inflat-
ing the tire to the recommended
pressure level.
6-10
What to do in an emergency
Never use an unauthorized
puncture-repairing agent to
repair and/or inflate an under-
inflated tire. Unauthorized tire
sealant may damage the tire
pressure sensor.
CAUTION
- TPMS
The TPMS cannot alert the driver to a sudden but severe
tire damage caused by exter-
nal factors, such as nails or
road debris.
When you sense any driving instability, immediately take
your foot off the accelerator,
lightly apply the brakes, and
slowly drive to a safe place off
the road.
WARNING

8.Insert the jack handle into the jack,turn it in a clockwise direction, and
raise the vehicle until the tire just
lifts above the ground. This would
be approximately 30 mm (1.2 in).
Before removing the wheel lug
nuts, make sure that the vehicle is
stationary without a possibility of
any movement or skid.
9.Loosen the wheel nuts and then remove them with your fingers.
Slide the wheel off the studs and
lay it on a flat ground to prevent
rolling away. To install the wheel on
the hub, pick up the spare tire, fit
the studs into the holes, and screw
them. When it is difficult, slightly tip
the wheel, fitting the top wheel hole
with its top stud. Then, shake the
wheel back and forth until the
wheel slide off other studs. 10. To reinstall a wheel, fit its hole
onto the studs, screw the wheel
nuts, and tighten them. The nuts
should be screwed with a small-
diameter end in an inward direc-
tion. Lightly jiggle the tire to
check its secure installment. If
necessary, tighten the nuts with
your fingers again.
11. Lower the vehicle onto the ground by rotating the wheel nut
wrench in a counterclockwise
direction.
6-15
What to do in an emergency06
Wheels may have sharp edges.
Carefully handle them to avoid a
possible severe injury. Before
installing wheels into place,
dust off any substances from
the hub or wheel (i.e. mud, tar,
gravel, etc., which may stick
solid against the hub).
When a wheel is unsecurely or
loosely installed on the hub, the
wheel nuts may become loose,
causing loss of a wheel. Loss of
a wheel may result in loss of
vehicle control, causing a seri-
ous injury or death.
WARNING
OVI065101N

The following lists are about the vehi-
cle inspection and maintenance that
should be performed by the owner or
an authorized EQUUS dealer, as
indicated. This will ensure your safety
and dependable driving.
Any adverse conditions should imme-
diately be checked by your EQUUS
dealer.
These Owner Maintenance Checklists
are mostly uncovered by your vehicle
warranties. Thus, you may charges
you for expenses of labor, parts or
lubricants.
Owner's maintenance sched-
ule
While refueling:
Check the engine oil level.
Check coolant level in coolantreservoir.
Check the windshield washer fluid level.
Check for any low or under-inflated tires.
While driving:
Check for any changes in theexhaust sounds or the smells.
Check for any steering wheel vibra- tion. Check whether you feel more
tightness or looseness of the steer-
ing wheel.
Check for any slight tilting, or “pulls” to one side, while driving on
a flat surface.
Check for any unusual sounds, tilt- ing, a braking distance, or “hard-to-
push” brake pedal while stopping.
Check the transmission fluid level upon experiencing a skid or a sud-
den transmission gear change.
Check the P(Park) function of the auto transmission.
Check the parking brake.
Check for any fluid leak (water dripping from the A/C while or after
the normal driving).
At least once a month:
Check the coolant level in theengine coolant reservoir.
Check the operation of all exterior lights, such as the stoplights, turn
signals and hazard warning flash-
ers.
Check the inflation pressures of all tires including the spare.
O OW
W N
NE
ER
R '
'S
S
M
M A
AI
IN
N T
TE
EN
N A
AN
N C
CE
E

7-7
Maintenance07
Carefully check your engine
coolant level, when the engine
is hot. The hot coolant or steam
may blow out under pressure.
This may cause a skin burn or
other serious injuries.
WARNING