maintenance schedule Hyundai Getz 2003 Owner's Guide

DO-IT-YOURSELF MAINTENANCE 6- 23
The various engine drive belts must be checked for condition, tension and free- dom from damage and excessive wear.The tension of a new belt must be checked after thirty minutes running following fitment of the new belt to allowfor the initial belt stretch. G190B01TB-GAT CHECKING DRIVE BELTS (Diesel)
A/C comp.
Auto tensioner Pulley
G190B01TB
AlternatorPower steering pump
At the scheduled maintenance inspec- tion, belts should be examined forcracks, wear, fraying or other evidence of deterioration and replaced if neces- sary.Belt routing should also be checked to be sure there is no interference be- tween the belts and other parts of theengine.
Crankshaft Pulley
SG190A1-E DRIVE BELTS (Gasoline)
1.1L
1.3L/1.6L Alternator
0.37 ~ 0.43 in. (9.5 ~11.0 mm)
Water Pump Pulley
Alternator Pulley
0.2~0.24 in.(5.1~6 mm)
HTB186
Crankshaft pulley
HTB220
Water Pump Pulley

7- 2 EMISSION CONTROL SYSTEMS
SH010A1-E EMISSION CONTROL SYSTEMS (Not all models) Depending upon the market for which the vehicle is destined, the emissioncontrol system will comprise one or more of the following emission con- trol devices. 1) Crankcase emission control sys-
tem
2) Evaporative emission control sys-
tem
z3) Exhaust emission control systemIn order that the proper functioning of the emission control systems may be ensured, it is recommended that the vehicle is inspected and maintainedby an authorized Hyundai dealer in accordance with the maintenance schedule in this manual. SH010B1-E
1. CRANKCASE EMISSION
CONTROLSYSTEM
The positive crankcase ventilation
system is employed to prevent airpollution caused by blow-by gasesbeing emitted from the crankcase by introducing fresh air to the crankcase through the air cleaner where thismixes with blow-by gases and then passes through the PCV valve into the intake manifold from where it sub-sequently enters the combustion chamber and is burned.
SH010C1-E
2. EVAPORATIVE EMISSION
CONTROL SYSTEM
The Evaporative Emission Control
System is designed to prevent fuel vapours from escaping into the atmo- sphere through the fuel tank ventila- tion system.
Whilst the engine is not running, fuel
vapours generated inside the fuel tankare absorbed and stored in a char-coal canister. When the engine is started, the vapours stored in the canister are drawn into the induction SH010D1-E
3. EXHAUST EMISSION CON
TROL SYSTEM
The exhaust emission control system
is a highly effective system whichcontrols exhaust emission while main- taining good vehicle performance.
system through the purge control so-lenoid valve and are subsequently burned.
The purge control solenoid valve is
controlled by the ECU; when the en-gine coolant temperature is low or the engine is idling, the purge control valve is closed and fuel vapours re-main stored in the canister. Under normal running conditions when the engine is warm, the valve opens andthe vapours are drawn into the inlet tract and subsequently burned in the combustion chamber.

10- 4 INDEX
M MAINTENANCE AND SERVICING
REQUIREMENTS ................................................... 5-2
MAINTENANCE UNDER SEVERE USAGE CONDITIONS .......................................................... 5-6
MANUAL TRANSAXLE ............................................... 2-8
MANUAL TRANSAXLE LUBRICANT ........................6-15
MIRROR .................................................................... 1-57
MULTI FUNCTION SWITCH ....................................1-46
OODOMETER ............................................................. 1-43
OUTSIDE REAR VIEW MIRROR .................. 1-57 ~ 1-58
OUTSIDE REAR VIEW MIRROR HEAT ...................1-59
OVERDRIVE SWI TCH .............................................. 2-12
PPARKING BRAKE ..................................................... 1-59
POLISHING ................................................................. 4-3POLLEN FILTER .............................................. 1-76, 6-20
POWER STEERING FLUID LEVEL ..........................6-26
POWER STEERING HOSES ...................................6-26
POWER W INDOW .................................................... 1-10
PROTECTING YOUR HYUNDAI FROM CORROSION .......................................................... 4-2 RREAR FOG LIGHT
SWITCH .................................... 1-51
REAR SEAT .............................................................. 1-13
REAR SEAT WARNING ........................................... 1-16
RECOMMENDED SHIFT SPEEDS ............................ 2-9
REMOTE FUEL FILLER LID RELEASE ...................1-61
REMOVAL OF WATER FROM THE FUEL FI LTER ............................................... 6-26
REPLACING LIGHT BULBS .....................................6-28
RUNNING IN ............................................................... 1-3
SSCHEDULED MAIN TENANCE................................... 5-3
SEAT ADJUSTMENT ................................................ 1-11
SEATBACK HOLDER ............................................... 1-63
SEAT BELT PRECA UTIONS.................................... 1-16
SEAT BELTS ............................................................ 1-18
SEAT POCKET ......................................................... 1-63
SERVICE HISTORY ................................................... 5-2
SMOOTH CORNERING ........................................... 2-15
SNOW TYRES ............................................................ 8-1
SPARE TYRE ............................................................. 3-5
SPARE WHEEL .......................................................... 3-6
SPARKING PLUG REPLACEMENT .........................6-13
SPECTACLE CASE .................................................. 1-56
SPEEDOMETER ....................................................... 1-42