wheel HYUNDAI I10 2021 Service Manual
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2021, Model line: I10, Model: HYUNDAI I10 2021Pages: 486, PDF Size: 6.04 MB
Page 370 of 486
7-18
Emergency situations
WARNING
& K D Q J L Q J D W \ U H F D Q E H G D Q J H U R X V
) R O O R Z W K H L Q V W U X F W L R Q V L Q W K L V V H F-
W L R Q Z K H Q F K D Q J L Q J D W \ U H W R
U H G X F H W K H U L V N R I V H U L R X V L Q M X U \ R U
G H D W K
CAUTION
% H F D U H I X O D V \ R X X V H W K H M D F N K D Q-
G O H W R V W D \ F O H D U R I W K H I O D W H Q G 7 K H
I O D W H Q G K D V V K D U S H G J H V W K D W F R X O G
F D X V H F X W V
- D F N D Q G W R R O V
OAC3079028TU
(1) Jack handle
(2) Jack
(3) Wheel lug nut wrench
(4) Towing hook
The jack, jack handle, wheel lug nut
wrench, and towing hook are stored
in the luggage compartment under
the luggage box cover.
OAC3079004TU
The jack is provided for emergency
tyre changing only.
Turn the winged hold down bolt coun-
terclockwise to remove the spare
tyre.
Store the spare tyre in the same com-
partment by turning the winged hold
down bolt clockwise.
To prevent the spare tyre and tools
from “rattling”, store them in their
proper location.
OAC3079005TU
If it is hard to loosen the tyre hold-
down wing bolt by hand, you can
loosen it easily using the jack handle.
1. Put the jack handle (1) inside of the
tyre hold-down wing bolt.
2. Turn the tyre hold-down wing bolt
counterclockwise with the jack
handle.
IF YOU HAVE A FLAT TYRE ãWITH SPARE TYRE IF EQUIPPEDä
Page 372 of 486
7-20
Emergency situations
OAC3079008TU
7. Place the jack at the designated
jacking position under the frame
closest to the tyre you are chang-
ing. The jacking positions are
plates welded to the frame with two
notches. Never jack any other
position or part of the vehicle.
Doing so may damage the side
seal molding or other parts of the
vehicle.
OAC3079009TU
8. Insert the jack handle into the jack
and turn it clockwise, raising the
vehicle until the tyre clears the
ground. Make sure the vehicle is
stable on the jack.9. Loosen the lug nuts with the wheel
lug nut wrench and remove them
with your fingers. Remove the
wheel from the studs and lay it flat
on the ground out of the way.
Remove any dirt or debris from the
studs, mounting surfaces, and
wheel.
10. Install the spare tyre onto the
studs of the hub.
11 . Tighten the lug nuts with your fin-
gers onto the studs with the small-
er end of the lug nuts closest to
the wheel.
12. Lower the vehicle to the ground
by turning the jack handle coun-
terclockwise.
OAC3079027TU
13. Use the wheel lug nut wrench to
tighten the lug nuts in the order
shown. Double-check each lug
nut until they are tight. After
changing tyres, we recommend
that a HYUNDAI authorised
repairer tighten the lug nuts to
their proper torque as soon as
possible. 7 K H Z K H H O O X J Q X W
V K R X O G E H W L J K W H Q H G W R a
N J I P a O E I I W
Page 373 of 486
7-21
07
If you have a tyre gauge, check the
tyre pressure (see “Tyres and
Wheels” in chapter 2 for tyre pressure
instructions.). If the pressure is lower
or higher than recommended, drive
slowly to the nearest service station
and adjust it to the recommended
pressure. Always reinstall the valve
cap after checking or adjusting tyre
pressure. If the cap is not replaced,
air may leak from the tyre. If you lose
a valve cap, buy another and install it
as soon as possible. After changing
tyres, secure the flat tyre and return
the jack and tools to their proper stor-
age locations.
NOTICE
Page 379 of 486
7-27
07
& R P S R Q H Q W V R I W K H 7 \ U H 0 R E L O L W \ . L W
1. Speed-restriction label
2. Sealant bottle and label with speed
restriction
3. Filling hose from sealant bottle to
wheel
4. Connectors and cable for the
power outlet direct connection
5. Holder for the sealant bottle
6. Compressor
7. ON/OFF switch8. Pressure gauge for displaying the
tyre inflation pressure
9. Button for reducing the tyre infla-
tion pressure
Connectors, cable and connection
hose are stored in the compressor
housing.
Strictly follow the specified sequence,
otherwise the sealant may escape
under high pressure.
ODE067044
Page 381 of 486
7-29
07
OAC3079013R
5. Plug the compressor power cord
(4) into the vehicle power outlet.
6. With the ignition switch in the ON
position, switch on the compressor
and let it run for approximately 5~7
minutes to fill the sealant up to
proper pressure. (refer to the Tyre
and Wheels, chapter 2). The infla-
tion pressure of the tyre after filling
is unimportant and will be checked/
corrected later.
Be careful not to overinflate the
tyre and stay away from the tyre
when filling it.
CAUTION
7 \ U H S U H V V X U H
' R Q R W D W W H P S W W R G U L Y H \ R X U Y H K L-
F O H L I W K H W \ U H S U H V V X U H L V E H O R Z
S V L N 3 D 7 K L V F R X O G U H V X O W L Q
D Q D F F L G H Q W G X H W R V X G G H Q W \ U H
I D L O X U H
7. Switch off the compressor.
8. Detach the hoses from the sealant
bottle connector and from the tyre
valve.
Return the Tyre Mobility Kit to its stor-
age location in the vehicle.
WARNING
& D U E R Q P R Q R [ L G H
' R Q R W O H D Y H \ R X U Y H K L F O H U X Q Q L Q J
L Q D S R R U O \ Y H Q W L O D W H G D U H D I R U
H [ W H Q G H G S H U L R G V R I W L P H & D U E R Q
P R Q R [ L G H S R L V R Q L Q J D Q G V X I I R F D-
W L R Q F D Q R F F X U
Page 384 of 486
![HYUNDAI I10 2021 Service Manual 7-32
Emergency situations
7 R Z L Q J V H U Y L F H
OAC3079029TU
[A] : Dolly
If emergency towing is necessary, we
recommend having it done by a
HYUNDAI authorised repairer or a
commercial tow-tr](/img/35/56227/w960_56227-383.png "HYUNDAI I10 2021 Service Manual 7-32
Emergency situations
7 R Z L Q J V H U Y L F H
OAC3079029TU
[A] : Dolly
If emergency towing is necessary, we
recommend having it done by a
HYUNDAI authorised repairer or a
commercial tow-tr")
7-32
Emergency situations
7 R Z L Q J V H U Y L F H
OAC3079029TU
[A] : Dolly
If emergency towing is necessary, we
recommend having it done by a
HYUNDAI authorised repairer or a
commercial tow-truck service.
Proper lifting and towing procedures
are necessary to prevent damage to
the vehicle. The use of wheel dollies
or flatbed is recommended.
It is acceptable to tow the vehicle with
the rear wheels on the ground (with-
out dollies) and the front wheels off
the ground.
If any of the loaded wheels or sus-
pension components are damaged or
the vehicle is being towed with the
front wheels on the ground, use a
towing dolly under the front wheels.
When being towed by a commercial
tow truck and wheel dollies are not
used, the front of the vehicle should
always be lifted, not the rear.
CAUTION
Page 385 of 486
7-33
07
When towing your vehicle in an emer-
gency without wheel dollies:
1. Place the ignition switch in the
ACC position.
2. Place the shift lever in N (Neutral).
3. Release the parking brake.
CAUTION
) D L O X U H W R S O D F H W K H V K L I W O H Y H U L Q 1
1 H X W U D O P D \ F D X V H L Q W H U Q D O G D P-
D J H W R W K H W U D Q V P L V V L R Q
5 H P R Y D E O H W R Z L Q J K R R N
OAC3079015TU
1. Open the tailgate, and remove the
towing hook from the tool case.
OAC3079016TU
2. Remove the hole cover by press-
ing the lower part of the cover on
the bumper.
3. Install the towing hook by turning it
clockwise into the hole until it is
fully secured.
4. Remove the towing hook and
install the cover after use.
Page 386 of 486
7-34
Emergency situations
( P H U J H Q F \ W R Z L Q J
OAC3079017TU
„Front
„Rear
OAC3079018TU
If towing is necessary, we recom-
mend you have it done by a HYUNDAI
authorised repairer or a commercial
tow truck service.
If towing service is not available in an
emergency, your vehicle may be tem-
porarily towed using a cable or chain
secured to the emergency towing
hook at the front (or rear) of the vehi-
cle.
Use extreme caution when towing the
vehicle with a cable or chain. A driver
must be in the vehicle to steer it and
operate the brakes.
Towing in this manner may be done
only on hard-surfaced roads for a
short distance and at low speeds.
Also, the wheels, axles, power train,
steering and brakes must all be in
good condition.
CAUTION
7 K H G U L Y H U P X V W E H L Q W K H Y H K L F O H
I R U V W H H U L Q J D Q G E U D N L Q J R S H U D-
W L R Q V Z K H Q W K H Y H K L F O H L V E H L Q J
W R Z H G 3 D V V H Q J H U V R W K H U W K D Q W K H
G U L Y H U P X V W Q R W E H L Q W K H Y H K L F O H
Always follow these emergency tow-
ing precautions:
‡ Place the ignition switch in the ACC
position so the steering wheel is not
locked.
Page 388 of 486
7-36
Emergency situations
Your vehicle is equipped with emer-
gency commodities to help you
respond to emergency situation.
) L U H H [ W L Q J X L V K H U
If there is small fire and you know
how to use the fire extinguisher, fol-
low these steps carefully.
1. Pull out the safety pin at the top of
the extinguisher that keeps the
handle from being accidentally
pressed.
2. Aim the nozzle towards the base of
the fire.
3. Stand approximately 2.5 m (8 ft)
away from the fire and squeeze the
handle to discharge the extinguish-
er. If you release the handle, the
discharge will stop.
4. Sweep the nozzle back and forth at
the base of the fire. After the fire
appears to be out, watch carefully
since it may re-ignite.
) L U V W D L G N L W
Supplies for use in giving first aid
such as scissors, bandage and adhe-
sive tape, etc. are provided.
7 U L D Q J O H U H I O H F W R U
Place the triangle reflector on the
road to warn oncoming vehicles
during emergencies, such as when
the vehicle is parked by the roadside
due to problems.
7 \ U H S U H V V X U H J D X J H
L I H T X L S S H G
Tyres normally lose some air in day-
to-day use, and you may have to add
a air periodically and usually it is not a
sign of a leaking tyre, but of normal
wear. Always check tyre pressure
when the tyres are cold because tyre
pressure increases with temperature.
To check the tyre pressure, take the
following steps:
1. Unscrew the inflation valve cap
that is located on the rim of the
tyre.
2. Press and hold the gauge against
the tyre valve. Some air will leak as
you begin and more will leak if you
don’t press the gauge in firmly.
3. A firm non-leaking push will acti-
vate the gauge.
4. Read the tyre pressure on the
gauge to see whether the tyre
pressure is low or high.
5. Adjust the tyre pressure to the
specified pressure. Refer to “Tyres
and Wheels” section in chapter 2.
6. Reinstall the inflation valve cap.
EMERGENCY COMMODITY ãIF EQUIPPEDä
Page 398 of 486
8
Tyres and wheels...............................................................................................8-29
Tyre care .........................................................................................................8-29
Recommended cold tyre inflation pressures ............................................. 8-30
Check tyre inflation pressure ....................................................................... 8-30
Tyre rotation ................................................................................................... 8-31
Wheel alignment and tyre balance ..............................................................8-32
Tyre replacement ...........................................................................................8-32
Wheel replacement .......................................................................................8-34
Tyre traction ...................................................................................................8-34
Tyre maintenance ..........................................................................................8-34
Tyre sidewall labelling ...................................................................................8-34
Low aspect ratio tyres ................................................................................... 8-37
Fuses ................................................................................................................. 8-38
Instrument panel fuse replacement ........................................................... 8-39
Fuse switch ................................................................................................... 8-39
Engine compartment panel fuse replacement .......................................... 8-40
Fuse/relay panel description ....................................................................... 8-42
Light bulbs ........................................................................................................ 8-50
Headlight, Position Light, Turn signal Light, Fog Light and
Daytime Running Light, Low Beam Assist-Static light bulb
replacement .................................................................................................. 8-51
Headlight and front fog light aiming............................................................8-55
Side repeater light replacement .................................................................. 8-59
Rear combination light bulb replacement ................................................. 8-60
High mounted stop light replacement ........................................................ 8-61
License plate light bulb replacement ......................................................... 8-62
Interior light bulb replacement ................................................................... 8-62
Appearance care .............................................................................................. 8-63
Exterior care .................................................................................................. 8-63
Interior care................................................................................................... 8-69
Emission control system .................................................................................. 8-72
Crankcase emission control system ............................................................ 8-72
Evaporative emission control system .......................................................... 8-72
Exhaust emission control system ................................................................. 8-73