Auto lock HYUNDAI I20 2014 User Guide

)' 
#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3
AAuto door lock/unlock features Impact sensing door unlock sys-
tem (if equipped)All doors will be automatically
unlocked when an impact causes the
air bags to deploy.Speed sensing door lock system (if equipped)All doors will be automatically locked
when vehicle speed exceeds 15
km/h (9 mph).
Child-protector rear door locksThe child safety lock is provided to
help prevent children seated in the
rear from accidentally opening the
rear doors. The rear door safety locks
should be used whenever children
are in the vehicle.
The child safety lock is located on
the edge of each rear door. When the
child safety lock is in the lock position
( ), the rear door will not open if
the inner door handle is pulled. To lock the child safety lock, insert a
key (or screwdriver) into the hole (1)
and turn it to the lock ( ) position.
To allow a rear door to be opened
from inside the vehicle, unlock the
child safety lock.
If children accidently open the rear
doors while the vehicle is in
motion, they could fall out of the
vehicle. The rear door safety locks
should always be used whenever
children are in the vehicle.
WARNING
OIB044045

)'#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3PPower windows (if equipped)
(1) Driver’s door power window
switch
(2) Front passenger’s door power window switch
(3) Rear door power window switch (Right)*
(4) Rear door power window switch (Left)*
(5) Window opening and closing
(6) Automatic power window*
(7) Power window lock switch
* : if equipped
'# &(
OIB044048

)'
#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3
IInformation
The automatic reverse feature is only
active when the “auto up” feature is
used by fully pulling up the switch to
the second detent.Do not install any accessories on the
windows. The automatic reverse fea-
ture may not operate.
Power window lock switch
(if equipped)The driver can disable the power
window switches on the rear passen-
gers' doors by pressing the power
window lock switch.
When the power window lock switch
is pressed:
• The driver's master control can
operate all the power windows.
• The front passenger's control can operate the front passenger's
power window.
• The rear passenger's control can- not operate the rear passengers'
power window.
• To prevent possible damage to thepower window system, do not
open or close two windows or
more at the same time. This will
also ensure the longevity of the
fuse.
• Never try to operate the main switch on the driver's door and the
individual door window switch in
opposite directions at the same
time. If this is done, the window will
stop and cannot be opened or
closed.
NOTICE
NOTICE
i
OIB044049
Make sure heads, other body
parts or other objects are safely
out of the way before closing the
windows to avoid injuries or vehi-
cle damage. Objects less than 4
mm (0.16 in.) in diameter caught
between the window glass and the
upper window channel may not be
detected by the automatic reverse
window and the window will not
stop and reverse direction.
WARNING

)'#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3
IItems
Explanation
Automatically Unlock
• Disable : The auto door unlock operation will be canceled.
• Vehicle Off: All doors will be automatically unlocked when the ignition key is removed from theignition switch or the Engine Star/Stop button is set to the OFF position.
Door
Light
Items
Explanation
One Touch Turn Signal
• Off: The one touch turn signal function will be deactivated.
• 3, 5, 7 Flashes : The lane change signals will blink 3, 5, or 7 times when the turn signal lever is moved slightly.For more details, refer to “Light” in this chapter.
Head Lamp Delay
• Off: The headlamp delay function will be deactivated.
• On: The head lamp delay function will be activated.For more details, refer to “Light” in this chapter.
User settings mode (Cluster Type B)In this mode, you can change setting of the instrument cluster, doors, lamps, and so on.

)'#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3
IItems
Explanation
Auto Lock
• Disable : The auto door lock operation will be deactivated.
• Enable on Speed : All doors will be automatically locked when the vehicle speed exceeds 9.3mph (15km/h).
• Enable on Shift : All doors will be automatically locked if the Continuously Variable Transaxle shift lever is shifted from the P (Park) position to the R (Reverse), N (Neutral), or D (Drive) position.
Auto Unlock
• Disable : The auto door unlock operation will be canceled.
• Vehicle Off: All doors will be automatically unlocked when the ignition key is removed from the ignition switch or the Engine Star/Stop button is set to the OFF position.
• On Shift to P: All doors will be automatically unlocked if the automatic transaxle shift lever is shift- ed to the P (Park) position.
Door
Light
Items
Explanation
One Touch Turn Signal
• Off: The one touch turn signal function will be deactivated.
• 3, 5, 7 Flashes : The lane change signals will blink 3, 5, or 7 times when the turn signal lever is moved slightly.For more details, refer to “Light” in this chapter.
Head Lamp Delay
• Off: The headlamp delay function will be deactivated.
• On: The head lamp delay function will be activated.For more details, refer to “Light” in this chapter.
User settings mode (Cluster Type C)In this mode, you can change setting of the instrument cluster, doors, lamps, and so on.

)')
#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3
HHeadlamp delay function
(if equipped)If the key is removed from the ignition
switch or placed in the ACC or
LOCK/OFF position with the head-
lights ON, the headlights (and/or
parking lights) remain on for about 5
minutes. However, with the engine off
if the driver’s door is opened and
closed, the headlights (and/or parking
lights) are turned off after 15 seconds.
The headlights (and/or parking
lights) can be turned off by pressing
the lock button on the remote key (or
smart key) twice or turning the light
switch to the OFF or AUTO position.
However, if you turn the light switch
to the AUTO position when it is dark
outside, the headlights will not be
turned off.
If the driver gets out of the vehicle
through other doors (except driver's
door), the battery saver function
does not operate and the headlamp
delay function does not turn off auto-
matically. Therefore, It causes the
battery to be discharged. In this
case, make sure to turn off the lamp before getting out of the vehicle.
Headlight leveling device (if equipped)To adjust the headlight beam level
according to the number of the pas-
sengers and loading weight in the
luggage area, turn the beam leveling
switch.
NOTICE
OIB044009

)'#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3
The higher the number of the switch
position, the low er the headlight
beam level. Always keep the head-
light beam at the proper leveling
position, or headlights may dazzle
other road users.
Listed below are the examples of
proper switch settings. For loading
conditions other than those listed
below, adjust the switch position so
that the beam level may be the near-
est as the condition obtained accord-
ing to the list.
DD aytime running light (DRL)
(if equipped)The Daytime Running Lights (DRL)
can make it easier for others to see
the front of your vehicle during the
day, especially after dawn and before
sunset.
The DRL system will turn the dedi-
cated lamp OFF when:
1. The headlights or front fog lights
are in the ON position.
2. The engine is turned off.
Interior lightsDo not use the interior lights for
extended periods when the engine is
turned off or the battery will dis-
charge.Interior lamp AUTO cutThe interior lamps will automatically
go off approximately 20 minutes after
the engine is turned off and the
doors closed. If a door is opened, the
lamp will go off 40 minutes after the
engine is turned off. If the doors are
locked by the remote key or smart
key and the vehicle enters the armed
stage of the theft alarm system, the
lamps will go off five seconds later.NOTICEDo not use the interior lights when
driving in the dark. The interior
lights may obscure your view and
cause an accident.
WARNING
Loading condition Switch position
Driver only 0
Driver + Front passenger 0
Full passengers
(including driver) 1
Full passengers (including
driver) + Maximum permis-
sible loading 2
Driver + Maximum permis-
sible loading 3

AAntenna
Type A,BThe roof antenna receives DRM and
both AM and FM broadcast signals.
Rotate the roof antenna in a counter-
clockwise direction to remove it.
Rotate it in a clockwise direction to
reinstall it.Type C The shark fin antenna receives trans-
mitted data. (for example: AM/FM,
and DRM)• Before entering a place with a low height clearance, be sure that the
antenna is removed.
• Be sure to r emove the antenna
before washing the vehicle in an
automatic car wash or it may be
damaged.
• When reinsta lling your antenna, it
is important that it is fully tightened
and adjusted to the upright position
to ensure proper reception. But it
could be removed when parking
the vehicle. Installation of aftermarket an
tenna
may result in water leakage, wind
noise, rattling & improper radio oper-
ation. We recommend to us e the
antenna available with an authorized
HYUNDAI dealer.
Information
Some models do not have audio (plas-
tic blanking cover) system, and will
not supply radio main cable. Thus if
you want to insert Aftermarket audio
or OEM audio to listen radio broad-
casting service, we recommend to use
the feeder cable available with an
authorized HYUNDAI dealer. iNOTICE
NOTICE
#
!'%$&%" '&$
OIB044036OIB045191OIB047193
■ Type B■Type A■Type C

#
!'%$&%" '&$
IInformation- Using Bluetooth
®
(BT) Audio
(if equipped)
• Bluetooth
®Audio Mode can be used
only when a Bluetooth
®
phone has
been connected.
• Bluetooth
®
Audio Mode will not be
available when connecting mobile
phones that do not support this fea-
ture.
• If a Bluetooth
®
Phone is being used
to play music and receives an
incoming or outgoing phone call,
then the music will stop.
• Moving the Track up/down while playing Bluetooth®audio mode may
result in pop noises with some
mobile phones.
• Bluetooth
®
streaming audio may
not be supported in some mobile
phones.
• When returning to Bluetooth
®
Audio mode after ending a call, the
mode may not automatically restart
in some mobile phones.
• Receiving an incoming call or mak- ing an outgoing call while playing
Bluetooth
®
Audio may result in
audio interference.
Media ModeChange Mode:
[MEDIA]
button
• Each time the button is pressed, the media mode popup will be dis-
played or closed.
• The media mode popup will not be displayed when
[SETUP/CLOCK]
button [Display] [Mode popup]
is turned [Off].
You can select a menu in the mode
popup by using the
[1]
~
[6]
(Preset) buttons or
TUNE
knob.
• If media device(USB, AUX) is con- nected, then it will automatically
operate. Once it is disconnected,
the previous mode will be restored.
• The Audio/Bluetooth
®(BT) Audio*/
AUX volume can also be con-
trolled.
* if equipped
Information
When you connect an Apple device,
playback does not start automatically.
Repeat:
[1 RPT]
button
• Repeats the current song or repeats all songs within the current
folder.
•iPod
®
mode: Repeat Song ➟
Repeat Off
• USB mode: Repeat Song ➟
Repeat Folder ➟ Off
Shuffle:
[2 SHFL]
button
• Plays all songs within the current
folder(category) or play all songs in
random order.
•iPod
®
mode: Shuffle All ➟ Shuffle
Off
• USB mode: Shuffle Folder ➟
Shuffle All ➟ Off
i
i

#
!'%$&%" '&$
SSoundPress the
[SETUP/CLOCK]
button 
Select [Sound].
• Position: Selects the sound position.
• Tone: Selects the sound tone.
• Speed Dependent Vol.: Controls the volume level automatically
according to the speed of the vehi-
cle.
Date/TimePress the
[SETUP/CLOCK]
button 
Select [Date/Time].
• Set Time: Adjusts the number cur- rently in focus to set the [hour], and
press the
TUNE
knob to set the
[minute] and [AM/PM].
• Time Format: Sets the 12/24 hour time format of the audio system.
• Set Date: Adjusts the number cur- rently in focus to make the settings
and press the
TUNE
knob to move
to the next settings.
• Display(Power Off): Displays time/date on screen when the
audio system turns power off.
Phone (if equipped)Add New DevicePress the
[SETUP/CLOCK]
button 
Select [Phone]  Select [Add New
Device].
• The following steps are the same as those described in the section
[Pairing a New Device] on the pre-
vious page.
Connect/Disconnect DevicePress the
[SETUP/CLOCK]
button 
Select [Phone]  Select [Paired
devices].
• Displays the paired Bluetooth
®
device list.
• From the paired device list, select the device you want to connect or
disconnect.
Information
• Displays the icons when Bluetooth
®
device is connected.
: An icon appears when you make
a Bluetooth
®Audio connection.
: An icon appears when you make
a Bluetooth®Handsfree connection.
• Only one Bluetooth
®
device can be
connected at a time.
• Bluetooth
®
Handsfree and
Bluetooth
®Audio functions are sup-
ported. Handsfree and audio-sup-
ported devices, such as a Bluetooth
®
smartphone or audio, will function
normally.
• If the system is not stable due to a vehicle- Bluetooth
®
device commu-
nication error, delete the paired
device on each device and pair/con-
nect the Bluetooth
®
device again.
i