warning HYUNDAI I20 2015 Owners Manual
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2015, Model line: I20, Model: HYUNDAI I20 2015Pages: 400, PDF Size: 7.02 MB
Page 355 of 400
1 . ( (
, 2 0 4 / 3 4 2 4 - 3
WWheel replacement When replacing the metal wheels for
any reason, make sure the new
wheels are equivalent to the original
factory units in diameter, rim width
and offset.
Tire tractionTire traction can be reduced if you
drive on worn tires, tires that are
improperly inflated or on slippery
road surfaces. Tires should be
replaced when tread wear indicators
appear. Slow down whenever there
is rain, snow or ice on the road, to
reduce the possibility of losing con-
trol of the vehicle.Tire maintenance In addition to proper inflation, correct
wheel alignment helps decrease tire
wear. If you find a tire worn unevenly,
have your dealer check the wheel
alignment.
When you have new tires installed,
make sure they are balanced. This
will increase vehicle ride comfort and
tire life. Additionally, a tire should
always be rebalanced if it is removed
from the wheel.
Tire sidewall labelingThis information identifies and
describes the fundamental charac-
teristics of the tire and also provides
the tire identification number (TIN)
for safety standard certification. The
TIN can be used to identify the tire in
case of a recall.1. Manufacturer or brand nameManufacturer or Brand name is
shown.
A wheel that is not the correct size
may adversely affect wheel and
bearing life, braking and stopping
a bilities, handling characteristics,
ground clearance, body-to-tire
clearance, snow chain clearance,
spee dometer and odometer cali-
bration, headlight aim and bumper
height.
WARNING
I030B04JM
1
1
2
34
5,6
7
Page 357 of 400
1 . ( $
, 2 0 4 / 3 4 2 4 - 3
33. Checking tire life (TIN : Tire
Identification Number) Any tires that are over 6 years old,
based on the manufacturing date,
(including the spare tire) should be
replaced by new ones. You can find
the manufacturing date on the tire
sidewall (possibly on the inside of the
wheel), displaying the DOT Code.
The DOT Code is a series of num-
bers on a tire consisting of numbers
and English letters. The manufactur-
ing date is designated by the last four
digits (characters) of the DOT code.DOT : XXXX XXXX OOOOThe front part of the DOT means a
plant code number, tire size and
tread pattern and the last four num-
bers indicate week and year manu-
factured.
For example:
DOT XXXX XXXX 1618 represents
that the tire was produced in the 16th
week of 2018.
4. Tire ply composition and materi- alThe number of layers or plies of rub-
ber-coated fabric in the tire. Tire
manufacturers also must indicate the
materials in the tire, which include
steel, nylon, polyester, and others.
The letter "R" means radial ply con-
struction; the letter "D" means diago-
nal or bias ply construction; and the
letter "B" means belted-bias ply con-
struction.5. Maximum permissible inflationpressureThis number is the greatest amount
of air pressure that should be put in
the tire. Do not exceed the maximum
permissible inflation pressure. Refer
to the Tire and Loading Information
label for recommended inflation
pressure.
Tire age
Tires degrade over time, even
when they are not being used.
Regardless of the remaining
tread, it is recommended that tires
generally be replaced after six (6)
years of normal service. Heat
caused by hot climates or frequent
high loading conditions can accel-
erate the aging process. Failure
to follow this warning could cause
sudden tire failure, which could lead to a loss of control and an
accident inv olving serious injury or
death.
WARNING
Page 358 of 400
1 . ( ' , 2 0 4 / 3 4 2 4 - 366. Maximum load ratingThis number indicates the maximum
load in kilograms and pounds that
can be carried by the tire. When
replacing the tires on the vehicle,
always use a tire that has the same
load rating as the factory installed
tire.7. Uniform tire quality grading Quality grades can be found where
applicable on the tire sidewall
between tread shoulder and maxi-
mum chapter width.
For example:
TREAD wear 200
TRACTION AA
TEMPERATURE A
Tread wearThe tread wear grade is a compara-
tive rating based on the wear rate of
the tire when tested under controlled
conditions on a specified govern-
ment test course. For example, a tire
graded 150 would wear one-and-a-
half times (1½) as well on the gov-
ernment course as a tire graded 100.
The relative performance of tires
depends upon the actual conditions
of their use, however, and may
depart significantly from the norm
due to variations in driving habits,
service practices and differences in
road characteristics and climate.
These grades are molded on the
side-walls of passenger vehicle tires.
The tires available as standard or
optional equipment on your vehicle
may vary with respect to grade.
Traction - AA, A, B & C The traction grades, from highest to
lowest, are AA, A, B and C. Those
grades represent the tire’s ability to
stop on wet pavement measured
under controlled conditions on spec-
ified government test surfaces of
asphalt and concrete. A tire marked
C may have poor traction perform-
ance. The traction grade assigned to this
tire is based on straight-ahead
braking traction tests, and does
not include acceleration, corner-
ing, hydroplaning, or peak traction
characteristics.
WARNING
Page 359 of 400
1 . ( 1
, 2 0 4 / 3 4 2 4 - 3
Temperature -A, B & C The temperature grades are A (the
highest), B, and C, representing the
tire’s resistance to the generation of
heat and its ability to dissipate heat
when tested under controlled condi-
tions on a specified indoor laboratory
test wheel.
Sustained high temperature can
cause the material of the tire to
degenerate and reduce tire life, and
excessive temperature can lead to
sudden tire failure. Grades B and A
represent higher levels of perform-
ance on the laboratory test wheel
than the minimum required by law.
LLow aspect ratio tire
(if equipped) Low aspect ratio tires, whose aspect
ratio is lower than 50, are provided
for sporty looks.
Because the low aspect ratio tires
are optimized for handling and brak-
ing, it may be more uncomfortable to
ride in and there is more noise com-
pare with normal tires.
Tire temperature
The temperature grade for this tire
is established for a tire that is
properly inflated and not over-
loaded. Excessive speed, under-
inflation, or excessive loading,
either separately or in combina-
tion, can cause heat build-up and
sudden tire failure. This can cause
loss of vehicle control a nd serious
injury or death.
WARNING
Page 361 of 400
1 . # &
, 2 0 4 / 3 4 2 4 - 3
$
A vehicle’s electrical system is pro-
tected from electrical overload dam-
age by fuses.
This vehicle has 2 fuse panels, one
located in the driver’s side panel bol-
ster, the other in the engine compart-
ment near the battery.
If any of your vehicle’s lights, acces-
sories, or controls do not work, check
the appropriate circuit fuse. If a fuse
has blown, the element inside the
fuse will be melted.
If the electrical system does not
work, first check the driver’s side
fuse panel.
Before replacing a blown fuse, dis-
connect the negative battery cable.
Always replace a blown fuse with
one of the same rating.
If the replacement fuse blows, this
indicates an electrical problem. Avoid
using the system involved and imme-
diately consult an authorized
HYUNDAI dealer.Three kinds of fuses are used: blade type for lower amperage rating, slowblow type and multi fuse for higheramperage ratings.
Do not use a screwdriver or any
other metal object to remove fuses
because it may cause a short circuit
and damage the system.
Information
The actual fuse/relay panel label may
differ from equipped items. iNOTICENOTICE
OTA070039
Normal
Normal
■ Slow Blow type
■ Multi fuse
B
B
l
l
o
o
w
w
n
n
Normal
■
Blade type
Fuse replacement•
Never replace a fuse with any-
thing but another fuse of the
same rating.
•
A higher capacity fuse could
cause damage and possibly a
fire.
•
Never install a wire or aluminum
foil instead of the proper fuse -
even as a temporary repair. It
may ca use extensive wiring
damage and a possible fire.
WARNING
B
B
l
l
o
o
w
w
n
n
B
B
l
l
o
o
w
w
n
n
Page 364 of 400
1 . # ) , 2 0 4 / 3 4 2 4 - 3
IInformation
If the memory fuse is pulled up from
the fuse panel, the warning chime,
audio, clock and interior lamps, etc.,
will not operate. Some items must
be reset after replacement. Refer to
"Battery" in this chapter.
Even though the memory fuse is pulled up, the battery can still be
discharged by operation of the
headlights or other electrical
devices.
Engine compartment panel fuse
replacement1. Turn the ignition switch and all
other switches off.
2. Remove the fuse box cover by pressing the tab and pulling up the
cover.
3. Check the removed fuse; replace it if it is blown. To remove or insert
the fuse, use the fuse puller in the
engine compartment fuse panel.
4. Push in a new fuse of the same rating, and make sure it fits tightly
in the clips. If it fits loosely, we rec-
ommend that you consult an
authorized HYUNDAI dealer.
After checking the fuse panel in the
engine compartment, securely install
the fuse panel cover. If not, electrical
failures may occur from water leak-
ing in.NOTICE
i
OIB074031
Page 368 of 400
1 . # ' , 2 0 4 / 3 4 2 4 - 3
FFuse Name
Symbol
Fuse rating
Circuit Protected
SENSOR
10A
Diesel 1.4 : Fuel Filter Warning Sensor
MODULE3
10A
A/C Control Module, E/R Junction Block (Multipurpose Check Conn ector), ATM Shift
Lever ILL., Center Facia Switch, Audio
PDM1
25A
Smart Key Control Module
PDM2
10A
Smart Key Control Module, Start/Stop Button Switch
MODULE2
10A
Parking Distance Warning Buzzer, Parking Distance Warning-Reverse LH/RH, Parking
Distance Warning-Reverse (CENTER) LH/RH
TCU
15A
CVT : Transaxle Range Switch, Pulse Generator 'A' / 'B',
M/T : Vehicle Speed Sensor, I/P Junction Block (Fuse - F26)
TA I L L P R H
RH
10A
Rear Combination Lamp (In/Out) RH, Head Lamp RH, ILL. (+), License Lamp (4DR),
License Lamp LH/RH (5DR)
TA I L L P L H
LH
10A
Rear Combination Lamp (In/Out) LH, Head Lamp LH, License Lamp
RR WIPER
15A
Rear Wiper Motor, PCB Block (Rear Wiper Relay)
ABS
10A
ABS Control Module
A/BAG
10A
SRS Control Module
ECU
10A
PCM/ECM, Smart Key Control Module
BRAKE SWITCH
10A
Stop Lamp Switch, Smart Key Control Module
CLUSTER
10A
Instrument Cluster
Driver’s side fuse panel
Page 376 of 400
1 . $ # , 2 0 4 / 3 4 2 4 - 3 ! # Consult an authorized HYUNDAI
dealer to replace most vehicle light
bulbs. It is difficult to replace vehicle
light bulbs because other parts of the
vehicle must be removed before you
can get to the bulb. This is especially
true for removing the headlight
assembly to get to the bulb(s).
Removing/installing the headlight
assembly can result in damage to
the vehicle.
Information
After heavy driving, rain or washing
headlight and taillight lenses could
appear frosty. This condition is caused
by the temperature difference
between the lamp inside and outside.
This is similar to the condensation on
your windows inside your vehicle dur-
ing the rain and doesn’t indicate a
problem with your vehicle. If the
water leaks into the lamp bulb circuit-
ry, we recommend that the system be
checked by an authorized HYUNDAI
dealer.
Be sure to replace the burned-out
bulb with one of the same wattage
rating. Otherwise, it may cause dam -
age to the fuse or electric wiring sys-
tem.
i
Prior to replacing a light, depress
the foot brake, move the shift lever
into the P (Park, for Continuo usly
Variable Transaxle vehicle) or
neutral (for Manual Transaxle
vehicle), apply the parking brake,
plac e the ignition switch in the
LOCK/OFF position, and take the
key with you when leaving the
vehicle to av oid sudden move-
ment of the vehicle and to prevent
possible electric shock.
Be aware the bulbs may be h ot
and may burn your fingers.
WARNING
Page 378 of 400
1 . $ ' , 2 0 4 / 3 4 2 4 - 3
(1) Headlight (Low/High) *
2
(2) Low Beam Assist-Static Light
(3) Front Turn Signal Light
(4) Position Light/ Daytime Running Light (DRL)
(5) Front Fog Light (if equipped)
*2: Bi-Function Projection Headlight
II nformation
If the headlight aiming adjustment
is necessary after the headlight
assembly is reinstalled, consult an
authorized HYUNDAI dealer.
The Fog Light aiming adjustment can be done by removing UNDER
COVER. Consult an authorised
HYUNDAI dealer.i(Continued)•
Always handle them carefully,
and avoid scratches and abra-
sions. If the bulbs are lit, avoid
contact w ith liquids. Never touch
the glass with bare hands.
Residual oil may cause the bulb
to overheat and burs t when lit. A
bulb should be operated only
when installed in a headlight.
•
If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
•
Wear eye protection when
changing a bulb. Allow the bulb
to cool down before handling it.
Halogen bulbs•
Halogen bulbs contain pressur-
ized gas that will produce flying
pieces of glass if broken.
(Continued)
WARNING
OLMB073042L
OIB077060
■Cross
• Type B
Page 383 of 400
1 . ' (
, 2 0 4 / 3 4 2 4 - 3
$ " $ # $Exterior careExterior general caution It is very important to follow the label
directions when using any chemical
cleaner or polish. Read all warning
and caution statements that appear
on the label. High-pressure washing• When using high-pressure washers,
make sure to maintain sufficient dis-
tance from the vehicle.
Insufficient clearance or excessive
pressure can lead to component
damage or water penetration.
• Do not spray the camera, sensors or its surrounding area directly with a
high pressure washer. Shock appliedfrom high pressure water may cause
the device to not operate normally.• Do not bring the nozzle tip close to boots (rubber or plastic covers) or
connectors as they may be damaged
if they come into contact with high
pressure water.
Finish maintenanceWashing To help protect your vehicle’s finish
from rust and deterioration, wash it
thoroughly and frequently at least
once a month with lukewarm or cold
water.
If you use your vehicle for off-road
driving, you should wash it after each
off-road trip. Pay special attention to
the removal of any accumulation of
salt, dirt, mud, and other foreign
materials. Make sure the drain holes
in the lower edges of the doors and
rocker panels are kept clear and
clean.
Insects, tar, tree sap, bird droppings,
industrial pollution and similar
deposits can damage your vehicle’s
finish if not removed immediately.
Even prompt washing with plain
water may not completely remove all
these deposits. A mild soap, safe for
use on painted surfaces, may be
used.
After washing, rinse the vehicle thor-
oughly with lukewarm or cold water.
Do not allow soap to dry on the fin-
ish.
• Do not use strong soap, chemicaldetergents or hot water, and do not
wash the vehicle in direct sunlig ht
or when the body of the vehicle is
warm.
• Be careful when washing the side windows of your vehicle.
Especially, with high-pressure
water, water may leak through the
windows and wet the interior.
• To prevent dam age to the plastic
parts and lamps, do not clean with
chemical solvents or strong deter- gents. NOTICEWet brakes
After washing the vehicle, test the
brakes while driving slowly to see
if they have been affected by
water. If braking performance is
impaired, dry the brakes by apply-
ing them lightly while maint aining
a slow forward speed.
WARNING