lock HYUNDAI I20 2017 User Guide

To prevent damage, NEVER hit or
pull on the headrests.
Adjusting the height up and down
(if equipped)
To raise the headrest, pull it up (1).
To lower the headrest, push and hold
the release button (2) on the head
rest support and lower the headrest
(3).
NOTICE
1
"&t%'s%st&'!"'%!'&&
(Continued)
•NEVER adjust the headrest
position of the driver’s seat when
the vehicle is in motion.
•Adjust the headrest as close to
the passenger’s head as possi
ble. Do not use a seat cushion
that holds the body away from
the seatback.
•Make sure the headrest locks
into position after adjusting it.
OIB034009
To reduce the risk of serious injury
or death in an accident, take the
following precautions when
adjusting your headrests:
•Always properly adjust the head
rests for all passengers BEFORE
starting the vehicle.
•NEVER let anyone ride in a seat
with the headrests removed.
•
Adjust the headrests so the middle
of the headrests is at the same
height as the height of the top of
the eyes.(Continued)
WARNING
OLF034072N

11
"&t%'s%st&'!"'%!'&&

Removal (if equipped)
To remove the headrest, raise it as far
as it can go then press the release
button (1) while pulling upward (2).To reinstall the headrest, put the
headrest poles (3) into the holes
while pressing the release button (1).
Then adjust it to the appropriate
height.
Folding the rear seat
The rear seatbacks (or cushions)
may be folded to facilitate carrying
long items or to increase the luggage
capacity of the vehicle. 1. Set the front seatback to the
upright position and if necessary,
slide the front seat forward.
2. Insert the rear lap\fshoulder belt plate into the holder on the side
trim. It will prevent the lap\fshoulder
belt from interfering with the seat
back when folding.
•Never allow passengers to sit on
top of the folded down seatback
while the vehicle is moving as
this is not a proper seating posi
tion and no seat belts are avail
able for use. This could result in
serious injury or death in case of
an accident or sudden stop.
•Objects carried on the folded
down seatback should not
extend higher than the top of the
front seats. This could allow
cargo to slide forward and cause
in

jury or damage during sudden
stops.
WARNING
OIB034010
Make sure the headrest locks in
position after adjusting it to prop
erly protect the occupants.
WARNING
OIB037011

12
"&t%'s%st&'!"'%!'&&
3. Pull up both sides of the seatback lever and fold the seatback toward
the front of the vehicle. To use the rear seat, lift and push up
the seatback backward. Push the
seatback firmly until it clicks into
place. Make sure the seatback is
locked in place.
When returning the rear seatbacks to
the upright position, remember to
return the rear shoulder belts to their
proper position.
Information
If you are not able to pull out the seat
belt from the retractor, firmly pull the
belt out and release it. Then you will
be able to pull the belt out smoothly.
iOIB037012
OIB034013
When you return the rear seat
back to its upright position after
being folded down:
Be careful not to damage the seat
belt webbing or buckle. Do not
allow the seat belt webbing or
buckle to get caught or pinched in
the rear seat. Ensure that the
seatback is completely locked into
its upright position by pushing on
the top of the seatback.
Otherwise, in an accident or sud
den stop, the seat could fold down
and allow cargo to enter the pas
sen

ger compartment, which could
result in serious injury or death.
WARNING

1
"&t%'s%st&'!"'%!'&&
If you continue not to fasten the seat
belt and you drive over 9 km\fh, the
illuminated warning light will start to
blink until you drive under 6 km\fh.
If you continue not to fasten the seat
belt and you drive over 20 km\fh (12
mph) the seat belt warning chime will
sound for approximately 100 sec
onds and the corresponding warning
light will blink.
*: if equipped
Lap\fshoulder belt
To fasten your seat belt:
To fasten your seat belt, pull it out of
the retractor and insert the metal tab
(1) into the buckle (2). There will be
an audible "click" when the tab locks
into the buckle. You should place the lap belt (1) por
tion across your hips and the shoul
der belt (2) por tion across your
chest.
The seat belt automatically adjusts to
the proper length only after the lap
belt portion is adjusted manually so
that it fits snugly around your hips. If
you lean forward in a slow, easy
motion, the belt will extend and let
you move around. If there is a sud
den stop or impact, however, the belt
will lock into position. It will also lock
if you try to lean forward too quickly.
ODH033055
ODH033053

1
"&t%'s%st&'!"'%!'&&

Information
If you are not able to pull out the safe
ty belt from the retractor, firmly pull
the belt out and release it. After
release, you will be able to pull the belt
out smoothly.
Height adjustment
(if equipped)
You can adjust the height of the shoul
der belt anchor to one of 3 positions
for maximum comfort and safety.
The height of the adjusting seat belt
should not be too close to your neck.
You will not be getting the most effec
tive protection. The shoulder portion
should be adjusted so that it lies
across your chest and midway over
your shoulder near the door and not
your neck.To adjust the height of the seat belt
anchor, lower or raise the height
adjuster into an appropriate position.
To raise the height adjuster, pull it up
(1). To lower it, push it down (3) while
pressing the height adjuster button
(2).
Release the button to lock the
anchor into position. Try sliding the
height adjuster to make sure that it
has locked into position.
i
OIB034015
Front seat

18
"&t%'s%st&'!"'%!'&&
To release the seat belt:
The seat belt is released by pressing
the release button (1) in the locking
buckle. When it is released, the belt
should automatically draw back into
the retractor.
If this does not happen, check the
belt to be sure it is not twisted, then
try again.
Lap belt (if equipped)
To fasten your seat belt:
To fasten a 2point static type belt,
insert the metal tab into the locking
buckle. There will be an audible
"click" when the tab locks into the
buckle. Check to make sure the belt
is properly locked and that the belt is
not twisted.
OLMB033088
OLMB033089
OLMB033025
You should place the lap belt por
tion as low as possible and snugly
across your hips, not on your waist.
If the lap belt is located too high on
your waist, it may increase the
chance of injury in the event of a
collision. Both arms should not be
under or over the belt. Rather, one
should be over and the other
under, as shown in the illustration.
Never wear the seat belt under the
arm nearest the door.
WARNING

19
"&t%'s%st&'!"'%!'&&

With a 2point static type seat belt, the
length must be adjusted manually so
it fits snugly around your body. Fasten
the belt and pull on the loose end to
tighten. The belt should be placed as
low as possible on your hips, not on
your waist. If the belt is too high, it
could increase the possibility of your
being injured in an accident. When using the rear center seat belt,
the buckle with the “CENTER” mark
must be used.To release the seat belt:
When you want to release the seat
belt, press the button (1) in the lock
ing buckle.
OIB034016
The center lap belt latching mech
anism is different from those for
the rear seat shoulder belts. When
fastening the rear seat shoulder
belts or the center lap belt, make
sure they are inserted into the cor
rect buckles to obtain maximum
protection from the seat belt sys
tem and assure proper operation.
WARNING
OLMB03309OLMB033090
Too high
ShortenCorrect

2
"&t%'s%st&'!"'%!'&&
Pretensioner seat belt
(if equipped)
Your vehicle is equipped with driver's
and front passenger's pretensioner
seat belts. The purpose of the pre
tensioner is to make sure that the
seat belts fit tightly against the occu
pant's body in certain frontal colli
sions. The pretensioner seat belts
may be activated in crashes where
the frontal collision is severe enough. When the vehicle stops suddenly, or
if the occupant tries to lean forward
too quickly, the seat belt retractor will
lock into position. In certain frontal
collisions, the pretensioner will acti
vate and pull the seat belt into tighter
contact against the occupant's body. The seat belt pretensioner system
consists mainly of the following com
ponents. Their locations are shown in
the illustration:
(1) SRS air bag warning light
(2) Retractor pretensioner assembly
(3) SRS control module
OIB034039
For your safety, be sure that the
belt webbing is not loose or twist
ed and always sit properly on your
seat.
WARNING
8KMB3311\fH

2
"&t%'s%st&'!"'%!'&&

To reduce the chance of serious or
fatal injuries:
•Children of all ages are safer
when restrained in the rear seat.
A child riding in the front passen
ger seat can be forcefully struck
by an inflating air bag resulting in
serious or fatal injuries.
•Always follow the instructions for
installation and use of the child
restraint maker.
•Always make sure the child seat
is secured properly in the car and
your child is securely
restrained
in the child seat.
•Never hold a child in your arms or
lap when riding in a vehicle. The
violent forces created during a
crash will tear the child from your
arms and throw the child against
the car’s interior.
(Continued)
WARNING (Continued)
•Never put a seat belt over yourself
and a child. During a crash, the
belt could press deep into the
child causing serious internal
injuries.
•Never leave children unattended
in a vehicle – not even for a short
time. The car can heat up very
quickly, resulting in serious
injuries to children inside. Even
very young children may inadver
tently cause the vehicle to move,
entangle themselves in the win
dows, or lock themselves or oth
ers inside the vehicle.
•Never allow two children, or any
two persons, to use the same seat
belt.
•Children often squirm and reposi
tion themselves improperly.
Never let a child ride with the
shoulder belt under their arm or
behind their back. Always proper
ly position and secure children in
rear seat.(Continued)
(Continued)
•Never allow a child to standup or
kneel on the seat or floorboard of
a moving vehicle. During a colli
sion or sudden stop, the child can
be violently thrown against the
vehicles interior, resulting in seri
ous injury.
•Never use an infant carrier or a
child safety seat that "hooks"
over a seatback, it may not pro
vide adequate security in an acci
dent.
•Seat belts can become very hot,
especially when the ca
r is parked
in direct sunlight. Always check
seat belt buckles before fasten
ing them over a child.
•After an accident, we recom
mend that the system be
checked by an authorized
HYUNDAI dealer.
•If there is not enough space to
place the child restraint system
because of the driver's seat,
install the child restraint system
in the rear right seat.

29
"&t%'s%st&'!"'%!'&&

Installing a child restraint systemby lap\fshoulder belt
To install a child restraint system on
the outboard or center rear seats, do
the following:
1. Place the child restraint system in
the seat and route the lap\fshoul
der belt around or through the
restraint, following the restraintmanufacturer’s instructions. Be
sure the seat belt webbing is not
twisted. 2. Fasten the lap\fshoulder belt latch
into the buckle. Listen for the dis
tinct “click” sound.Position the release button so that it is easy to access in case of an emergency.
3. Buckle the seat belt and allow the seat belt to take up any slack. After
installation of the child restraint
system, try to move it in all direc
tions to be sure the child restraint
system is securely installed.
If you need to tighten the belt, pull
more webbing toward the retractor.
When you unbuckle the seat belt and
allow it to retract, the retractor will
automatically revert back to its nor
mal seated passenger emergency
locking usage condition.
MMSA3030E2BLD310
E2MS103005