oil HYUNDAI I20 2017 Owner's Manual

1.%),204/3424-3$$ " !"##$$# !"$" "$#!$Engine oil and filterThe engine oil and filter should be
changed at the intervals specified in
the maintenance schedule. If the car
is being driven in severe conditions,
more frequent oil and filter changes
are required.Drive beltsInspect all drive belts for evidence of
cuts, cracks, excessive wear or oil
saturation and replace if necessary.
Drive belts should be checked peri-
odically for proper tension and
adjusted as necessary.When you are inspecting the belt,
place the ignition switch in the
LOCK/OFF or ACC position.
Fuel filterA clogged filter can limit the speed at
which the vehicle may be driven,
damage the emission system and
cause multiple issues such as hard
starting. If an excessive amount of
foreign matter accumulates in the
fuel tank, the filter may require
replacement more frequently.
After installing a new filter, run the
engine for several minutes, and
check for leaks at the connections.
We recommend that the fuel filter be
replaced by an authorized HYUNDAI
dealer.
Fuel lines, fuel hoses and con-
nectionsCheck the fuel lines, fuel hoses and
connections for leakage and dam-
age. We recommend that the fuel
lines, fuel hoses and connections be
replaced by an authorized HYUNDAI
dealer.
NOTICE
Diesel only
Never work on injection system
with engine running or within 30
seconds after shutting off engine.
High pressure pump, rail, injectors
and high pressure pipes are sub-
ject to high pressure even a fter
the engine stopped. The fuel jet
produced by fuel leaks may cause
serious injury, if it touch the b ody.
People using pacemakers should
not move than 30cm closer to the
ECU or wiring harness within the
eng ine room while engine is run-
ning, since the high currents in the
Common Rail system produce
considerab le magnetic fields.
WARNING

1.%',204/3424-3$$"!"$#!Checking the engine oil level
(Petrol engiene)1.Be sure the vehicle is on level
ground.
2.Start the engine and allow it to reach normal operating tempera-
ture.
3.Turn the engine off and wait for a few minutes (about 5 minutes) for
the oil to return to the oil pan.
4.Pull the dipstick out, wipe it clean, and reinsert it fully.
5.Pull the dipstick out again and check the level. The level should be
between F (Full) and L (Low). If it is near or at L (Low), add enough
oil to bring the level to F (Full).
Do not
overfill.
Use a funnel to help prevent oil from
being spilled on engine components.
Use only the specified engine oil. (Refer to "Recommended lubricantsand capacities" in chapter 8.)
Radiator hose
Be very careful not to touch the
radiator hose when checking or
adding the engine oil as i t may be
hot enough to burn you.
WARNING
OIB074004
OIB074006
•
Do not overfill the engine oil. It
may damage the engine.
•
Do not spill engine oil, when
adding or changing engine oil. If
you drop the engine oil on the
engine ro om, wipe it off immedi-
ately.
•
When you wipe the oil level
gauge, you should wipe it with a
clean cloth. When mixed with
debris, it can cause engine dam-
age.
CAUTION

1.+#,204/3424-3D
Do not allow brake/clutch fluid to
contact the vehicle's body paint, as
paint damage will result.
Brake/clutch fluid, which has been
exposed to open air for an extended
time should never be used as its
qualit y cannot be guaranteed. It
should be properly disposed. Don't
put in the wrong kind of fluid. A few
drop s of mineral-based oil, such as
engine oil, in your brake/clutch sys-
tem can damage brake/clutch sys-
t em parts. NOTICE
Brake/clutch fluid
When changing and adding
brake/clutch fluid, handle it care-
fully. Do not let it com e in contact
with your eyes. If brake/clutch fluid
come in contact with your eyes,
immediately flush the m with a
large quantity of fresh tap water.
Have your eyes examined by a
doctor as soon as possible.
WARNING

1.)',204/3424-3
RReset itemsItems should be reset after the bat-
tery has been discharged or the bat-
tery has been disconnected.
• Auto up/down window
(See chapter 3)
• Climate control system (See chapter 3)
• Audio (See chapter 3)Battery replacementReplacing a Battery required precau-
tionary measures.
We recommend that you consult an
authorized HYUNDAI dealer.
•
Disconnect the battery charger
in the following order.
1.Turn off the battery charger main switch.
2.Unho ok the negative clamp from
the negative battery terminal.
3.Unhook the positive clamp from the positive battery terminal.
•
Before performing maintenance
or recharging the battery, turn
off all accessories and stop the
engine.
•
The negative battery cable must
be removed first and installed
last when the battery is discon-
nected.
WARNING
Recharging battery
When recharging the battery,
observe the following precautions:•
The battery must be removed
from the vehicle and placed in
an area with good ventilation.
•
Do not allow cigarettes, sparks,
or flame near the battery.
•
Watch the battery during charg-
ing, and stop or reduce the
charging rate if the battery cells
begin gas sing (boiling) violently
or if the temperature of the elec-
trolyte of any cell exceeds 49°C
(120°F).
•
Wear eye protection when
checking the battery during
charging.
(Continued)
(Continued)
WARNING

1.#&
,204/3424-3
$
A vehicle’s electrical system is pro-
tected from electrical overload dam-
age by fuses.
This vehicle has 2 fuse panels, one
located in the driver’s side panel bol-
ster, the other in the engine compart-
ment near the battery.
If any of your vehicle’s lights, acces-
sories, or controls do not work, check
the appropriate circuit fuse. If a fuse
has blown, the element inside the
fuse will be melted.
If the electrical system does not
work, first check the driver’s side
fuse panel.
Before replacing a blown fuse, dis-
connect the negative battery cable.
Always replace a blown fuse with
one of the same rating.
If the replacement fuse blows, this
indicates an electrical problem. Avoid
using the system involved and imme-
diately consult an authorized
HYUNDAI dealer.Three kinds of fuses are used: blade type for lower amperage rating, slowblow type and multi fuse for higheramperage ratings.
Do not use a screwdriver or any
other metal object to remove fuses
because it may cause a short circuit
and damage the system.
Information
The actual fuse/relay panel label may
differ from equipped items. iNOTICENOTICE
OTA070039
Normal
Normal
■ Slow Blow type
■ Multi fuse
B
B
l
l
o
o
w
w
n
n
Normal
■
Blade type
Fuse replacement•
Never replace a fuse with any-
thing but another fuse of the
same rating.
•
A higher capacity fuse could
cause damage and possibly a
fire.
•
Never install a wire or aluminum
foil instead of the proper fuse -
even as a temporary repair. It
may ca use extensive wiring
damage and a possible fire.
WARNING
B
B
l
l
o
o
w
w
n
n
B
B
l
l
o
o
w
w
n
n

1.$%,204/3424-3[ ] : MFR (Multi Focus Reflector) Headlight
( ) : Bi-Function Projection HeadlightPCB Block (Gasoline engine)FF use Name
Symbol
Fuse rating
Circuit Protected
ECU 1
30A
PCB Block (Engine Control Relay, Fuse - F25)
HORN
15A
Horn Relay, B/Alarm Horn Relay
FUEL PUMP
20A
F/Pump Relay
WIPER FRT
25A
Wiper Lo Relay
DRL
(10A)
DRL Relay
H/LAMP LO
20A
H/Lamp Lo Relay
H/LAMP HI
[20A] (10A)
H/Lamp Hi Relay
C/FAN
40A
C/Fan Lo Relay, C/Fan Hi Relay
BLOWER
50A
Blower Relay
IG 2
30A
Start Relay, W/O Button Start : Ignition Switch, With Button St art : PDM Relay Box (IG2 Relay)
B+2
30A
I/P Junction Block (P/WDW Relay, TAIL Relay, Fuse - F1)
TCU 1
10A
1.2 CVT : PCM
ECU 3
15A
F/Pump Relay, ECM, C/Fan HI/LO Relay, Camshaft Position Sensor #1/#2, Oxygen Sensor
(Up/Down), Oil Control Valve #1/#2, Purge Control Solenoid Valve, Variable Intake Solenoid
Valve, A/CON Relay, Immobilizer Module
B/UP LAMP
B/UP
LAMP
10A
CVT : PCM, Transaxle Range Switch, Instrument Cluster, Audio
M/T : Back-Up Lamp Switch, I/P Junction Block (Fuse - F26)

1.$+
,204/3424-3
PCB Block (Gasoline engine)FFuse Name
Symbol
Fuse rating
Circuit Protected
H/LAMP RH
10A
Head Lamp RH
H/LAMP LH
10A
Head Lamp LH
TCU 2
15A
1.4 A/T : PCM
ECU 2
15A
ECM/PCM, Injector #1/#2/#3#4
IGN COIL
15A
Ignition Coil #1/#2/#3/#4, Condenser

1.$',204/3424-3
(1) Headlight (Low/High) *
2
(2) Low Beam Assist-Static Light
(3) Front Turn Signal Light
(4) Position Light/ Daytime Running Light (DRL)
(5) Front Fog Light (if equipped)
*2: Bi-Function Projection Headlight
II nformation
If the headlight aiming adjustment
is necessary after the headlight
assembly is reinstalled, consult an
authorized HYUNDAI dealer.
The Fog Light aiming adjustment can be done by removing UNDER
COVER. Consult an authorised
HYUNDAI dealer.i(Continued)•
Always handle them carefully,
and avoid scratches and abra-
sions. If the bulbs are lit, avoid
contact w ith liquids. Never touch
the glass with bare hands.
Residual oil may cause the bulb
to overheat and burs t when lit. A
bulb should be operated only
when installed in a headlight.
•
If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
•
Wear eye protection when
changing a bulb. Allow the bulb
to cool down before handling it.
Halogen bulbs•
Halogen bulbs contain pressur-
ized gas that will produce flying
pieces of glass if broken.
(Continued)
WARNING
OLMB073042L
OIB077060
■Cross
• Type B

1.'#,204/3424-3
•• Water washing in the engine com-
partment including high pressure
water washing may cause the fail-
ure of electrical circuits located in
the engine compartment.
• Never allow water or other liquids to come in contact with
electrical/electronic components
inside the vehicle as this may dam-
age them.
WaxingWax the vehicle when water will no
longer bead on the paint.
Always wash and dry the vehicle
before waxing. Use a good quality
liquid or paste wax, and follow the
manufacturer’s instructions. Wax all
metal trim to protect it and to main-
tain its luster.
Removing oil, tar, and similar materi-
als with a spot remover will usually
strip the wax from the finish. Be sure to
re-wax these areas even if the rest of
the vehicle does not yet need waxing. • Wiping dust or dirt off the body with a dry cloth will scratch the finish.
• Do not use steel wool, abrasive cleaners , or strong detergents con-
taining highly alkaline or caustic
agents on chrome-plated or
a nodized aluminum parts. This
may result in damage to the pro-
tective coating and cause discol-
oration or paint deterioration.
Finish damage repair Deep scratches or stone chips in the
painted surface must be repaired
promptly. Exposed metal will quickly
rust and may develop into a major
repair expense.
Information
If your vehicle is damaged and
requires any metal repair or replace-
ment, be sure the body shop applies
anti-corrosion materials to the parts
repaired or replaced. i
NOTICE
NOTICE
OLMB073082

1.1,204/3424-3
KK eep your garage dryDon't park your vehicle in a damp,
poorly ventilated garage. This cre-
ates a favorable environment for cor-
rosion. This is particularly true if you
wash your vehicle in the garage or
drive it into the garage when it is still
wet or covered with snow, ice or
mud. Even a heated garage can con-
tribute to corrosion unless it is well
ventilated so moisture is dispersed.Keep paint and trim in good condi-
tionScratches or chips in the finish
should be covered with "touch-up"
paint as soon as possible to reduce
the possibility of corrosion. If bare
metal is showing through, the atten-
tion of a qualified body and paint
shop is recommended.
Bird droppings : Bird droppings are
highly corrosive and may damage
painted surfaces in just a few hours.
Always remove bird droppings as
soon as possible.
Don't neglect the interiorMoisture can collect under the floor
mats and carpeting and cause corro-
sion. Check under the mats periodi-
cally to be sure the carpeting is dry.
Use particular care if you carry fertil-
izers, cleaning materials or chemi-
cals in the vehicle.
These should be carried only in
proper containers and any spills or
leaks should be cleaned up, flushed
with clean water and thoroughly
dried.
Interior careInterior general precautions Prevent chemicals such as perfume,
cosmetic oil, sun cream, hand clean-
er, and air freshener from contacting
the interior parts because they may
cause damage or discoloration. If
they do contact the interior parts,
wipe them off immediately. See the
instructions that follow for the proper
way to clean vinyl. Never allow water or other liquids to
come in contact with electrical/ elec-
tronic components inside the vehicle
as this may damage them.
When cleaning leather products
(steering wheel, seats etc.), use neu -
tral detergents or low alcohol content
solutions. If you use high alcohol
c ontent solutions or acid/al kaline
detergents, the color of the leather
may fade or the surface may get
stripped off.NOTICENOTICE