HYUNDAI I20 2021 Repair Manual

4-28
Safety system
Installing a Child Restraint
System (CRS)
WARNING
Before installing your Child Restraint
System always:
• Read and follow the instructions
provided by the manufacturer of the
Child Restraint System.
Failure to follow all warnings and
instructions could increase the risk of
the SERIOUS INJURY or DEATH if an
accident occurs.
WARNING
If the vehicle headrest prevents proper
installation of a Child Restraint System
(as described in the Child Restraint
System manual), the headrest of the
respective seating position shall be
readjusted or entirely removed.After selecting a proper Child Restraint
System and checking that the Child
Restraint System fits properly in the rear
of this vehicle, you are ready to install
the Child Restraint System according to
the manufacturer’s instruction. There are
three general steps in installing the Child
Restraint System properly:
• Properly secure the Child Restraint
System to the vehicle. All Child
Restraint Systems must be secured to
the vehicle with the lap belt or lap part
of a lap/shoulder belt or with the top-
tether and/or ISOFIX anchorage.
• Make sure the Child Restraint System
is firmly secured. After installing a
Child Restraint System to the vehicle,
push and pull the Child Restraint
System forward and from side-
to-side to verify that it is securely
attached to the vehicle seat. A Child
Restraint System secured with a seat
belt should be installed as firmly as
possible. However, some side-to-side
movement can be expected.
When installing a Child Restraint
System, adjust the vehicle seat (up
and down, forward and rearward)
so that your child fits in the Child
Restraint System in a comfortable
manner.
• Secure the child in the Child
Restraint System. Make sure the
child is properly strapped in the Child
Restraint System according to the
Child Restraint System manufacturer’s
instructions.
WARNING
A Child Restraint System in a closed
vehicle can become very hot. To
prevent burns, check the seating
surface and buckles before placing
your child in the Child Restraint
System.

4-29
04
CRS categoriesSeating positions
123
456
Airbag ON Airbag Off
Universal belted CRS All mass groups - - NoYes
1)
(F,R)Yes
(F,R)Yes
2)
(F,R)Yes
(F,R)
i-size CRSISOFIX CRF : F2, F2X,
R1, R2- - No No No No No
Carry-cot
(ISOFIX lateral facing CRS)ISOFIX CRF: L1, L2 - - No No No No No
ISOFIX infant* CRS
(* : ISOFIX baby CRS)ISOFIX CRF : R1 - - No NoYes
(R)NoYes
(R)
ISOFIX toddler CRS - smallISOFIX CRF : F2,F2X,
R2,R2X- - No NoYes
(F,R)NoYes
(F,R)
ISOFIX toddler CRS – large*
(* : not booster seats)ISOFIX CRF : F3,R3 - - No NoYes
(F,R)NoYes
(F,R)
Booster Seat – reduced Width ISO CRF : B2 - - No Yes Yes Yes Yes
Booster Seat – full Width ISO CRF : B3 - - No Yes Yes Yes Yes
Suitability of each seating position for belted & ISOFIX Child Restraint Systems (CRS) according to UN
regulations (Information for use by vehicle users and CRS manufacturers)• Yes : Suitable for fitment of the designated category of CRS
• No : Not suitable for fitment of the designated category of CRS
• “-” : Not applicable
The table is based on RHD vehicle. Except for the front passenger seat, the table is valid for LHD vehicle. For LHD vehicle
front passenger seat, please use information for the seating position number 1.F : Forward facing, R : Rearward facing
Note
1) : To install Universal CRS to 2nd row seating positions, 1st row seat should be adjust forward properly.
To install Universal CRS, 1st row seat back should be at upright position
Note 2) : Never install CRS with a support leg on 2nd row center seating position.
If Seat belt is 2 point type, forward facing type CRS can be installed only .

4-30
Safety system
Seat NumberPosition
in the vehicleSeating positions
1 Front left
2 Front center
3 Front right
42
nd row left
52
nd row center
62
nd row right
 If the vehicle headrest prevents proper installation of a CRS, the headrest of the
seating position shall be readjusted or entirely removed
 Never place a rearward facing Child Restraint System on the front passenger seat,
unless the air bag is deactivated.

4-31
04
ISOFIX anchorage and top-tether
anchorage (ISOFIX system) for
children (if equipped)
The ISOFIX system holds a Child
Restraint System during driving and in
an accident. This system is designed
to make installation of the Child
Restraint System easier and reduce
the possibility of improperly installing
your Child Restraint System. The ISOFIX
system uses anchors in the vehicle and
attachments on the Child Restraint
System. The ISOFIX system eliminates
the need to use seat belts to secure the
Child Restraint System to the rear seats.
ISOFIX anchors are metal bars built into
the vehicle. There are two lower anchors
for each ISOFIX seating position that will
accommodate a Child Restraint System
with lower attachments.
To use the ISOFIX system in your
vehicle, you must have a Child Restraint
System with ISOFIX attachments. (An
ISOFIX-Child Restraint System may only
be installed if it has vehicle-specific or
universal approval in accordance with
the requirements of ECE-R 44 or ECE-R
129.)
The Child Restraint System manufacturer
will provide you with instructions on how
to use the Child Restraint System with its
attachments for the lower anchorages.
OLM039035OLM039035
ISOFIX anchorages have been provided
in the left and right outboard rear
seating positions. Their locations are
shown in the illustration. There are no
ISOFIX anchorages provided for the
center rear seating position.
WARNING
Do not attempt to install a Child
Restraint System using ISOFIX
anchorages in the rear center
seating position. There are no ISOFIX
anchorages provided for this seat.
Using the outboard seat anchorages,
for the CRS installation on the rear
center seating position, can damage
the anchorages which may break or fail
in a collision resulting in serious injury
or death.

4-32
Safety system
OAI3039016OAI3039016
The ISOFIX anchorages symbols are
located on the left and right rear seat
cushions to identify the position of the
ISOFIX anchorages in your vehicle (see
arrows in illustration).
OAI3039017OAI3039017
Both rear outboard seats are equipped
with a pair of ISOFIX anchorages as well
as a corresponding top-tether anchorage
on the back side of the rear seats.
(Child Restraint Systems with universal
approval according to ECE-R44 or
ECE-R129 need to be fixed additionally
with a top-tether connected to the
corresponding top-tether anchorage
point on the back side of the rear seats.)
ISOFIX anchorages are located between
the seatback and the seat cushion of the
rear seat left and right outboard seating
positions.
Securing a Child Restraint System
with the “ISOFIX system”
To install a ISOFIX-compatible Child
Restraint System in either of the rear
outboard seating positions:
1. Move the seat belt buckle away from
the ISOFIX anchorages.
2. Move any other objects away from
the anchors that could prevent a
secure connection between the Child
Restraint System and the ISOFIX
anchorages.
3. Place the Child Restraint System on
the vehicle seat, then attach the seat
to the ISOFIX anchorages according to
the instructions provided by the Child
Restraint System manufacturer.
4. Follow the instructions of the Child
Restraint System’s manufacturer for
proper installation and connection
of the ISOFIX attachments on the
Child Restraint System to the ISOFIX
anchorages.
WARNING
Take the following precautions when
using the ISOFIX system:
• Read and follow all installation
instructions provided with your Child
Restraint System.
• To prevent the child from reaching
and taking hold of unretracted
seat belts, buckle all unused rear
seat belts and retract the seat belt
webbing behind the child. Children
can be strangled if a shoulder belt
becomes wrapped around their neck
and the seat belt tightens.

4-33
04
• NEVER attach more than one
Child Restraint System to a single
anchorage. This could cause the
anchor or attachment to come loose
or break.
• Always have the ISOFIX system
inspected by your dealer after an
accident. An accident can damage
the ISOFIX system and may not
properly secure the Child Restraint
System.
Securing a Child Restraint System
with “Top-tether anchorage”
system (if equipped)
OBI3030004OBI3030004
First, secure the Child Restraint System
with the ISOFIX anchorages or the
seat belt. If the Child Restraint System
manufacturer recommends the top-
tether to be attached, attach and
tighten the top-tether to the top-tether
anchorage. Top-tether anchorages are
located on the back of the rear seats.
WARNING
Take the following precautions when
installing the top-tether:
• Read and follow all installation
instructions provided with your Child
Restraint System.
• NEVER attach more than one Child
Restraint System to a single top-
tether anchorage. This could cause
the anchorage or attachment to
come loose or break.
• Do not attach the top-tether to
anything other than the correct top-
tether anchorage. It may not work
properly if attached to something
else.
• Child Restraint System anchorages
are designed to withstand only those
loads imposed by correctly fitted
Child Restraint Systems. Under no
circumstances are they to be used for
adult seat belts or harnesses or for
attaching other items or equipment
to the vehicle.

4-34
Safety system
OAI3039018OAI3039018
To install the top-tether :
1. Route the Child Restraint System
top-tether over the Child Restraint
System seatback. Route the top-tether
under the headrest and between the
headrest posts, or route the top-tether
over the top of the vehicle seatback.
Make sure the strap is not twisted.
2. Connect the top-tether to the top-
tether anchorage, then tighten
the top-tether according to the
instructions of your Child Restraint
System’s manufacturer to firmly
attach the Child Restraint System to
the seat.
3. Check that the Child Restraint System
is securely attached to the seat by
pushing and pulling the seat forward
and from side-to-side.
Installing a child restraint system by
lap/shoulder belt
E2MS103005E2MS103005
To install a child restraint system on the
outboard or center rear seats, do the
following:
1. Place the child restraint system in
the seat and route the lap/shoulder
belt around or through the restraint,
following the restraint manufacturer’s
instructions. Be sure the seat belt
webbing is not twisted.
E2BLD310E2BLD310
2. Fasten the lap/shoulder belt latch
into the buckle. Listen for the distinct
“Click” sound.
Position the release button so that it is
easy to access in case of an emergency.

4-35
04
MMSA3030MMSA3030
3. Buckle the seat belt and allow the
seat belt to take up any slack. After
installation of the child restraint
system, try to move it in all directions
to be sure the child restraint system is
securely installed.
If you need to tighten the belt, pull more
webbing toward the retractor. When you
unbuckle the seat belt and allow it to
retract, the retractor will automatically
revert back to its normal seated
passenger emergency locking usage
condition.

4-36
Safety system
Child Seat Restraint for Vehicle ISOFIX PositionsUse child safety seats that have been officially approved and are appropriate for your children. When using the child safety
seats, refer to the following table..
Mass GroupSeating Position
Front PassengerSecond Row
Outboard LeftCenter
(2 POINT BELT)Outboard Right
Group 0
(0-9months)up to 10kg X U X U
Group 0+
(0-2years)up to 13kg X U X U
Group I
(9months-4years)9 to 18kg X U UF U
Group II
(15 to 25kg)15 to 25kg X U UF U
Group III
(22 to 36kg)22 to 36kgD X U UF U
U = Suitable for “universal” category Child Restraints Systems approved for use in this mass group.
UF = Suitable for forward facing “universal” category restraints for use in this mass group.
X = Seat position not suitable for children in this mass group.

Remarks:- Co driver seat:
Up right, Rearmost position & Seat belt shoulder anchorage to lowest position.

4-37
04
$,5%$*