light HYUNDAI I20 2023 Owners Manual

8-3
08
OBC3N080001
The hazard warning flasher serves as a
warning to other drivers to exercise
extreme caution when approaching,
overtaking, or passing your vehicle.
It should be used whenever emergency
repairs are being made or when the
vehicle is stopped near the edge of a
roadway.
To turn the hazard warning flasher on
or off, press the hazard warning flasher
button with the ignition switch in any
position. The button is located in the
centre fascia panel. All turn signal lights
will flash simultaneously.

[The hazard warning flasher operates
whether your vehicle is running or not.

[The turn signals do not work when the
hazard flasher is on.
HAZARD WARNING FLASHER

8-5
08
If the engine doesn’t turn over
or turns over slowly

[Be sure the shift lever is in N (Neutral)
or P (Park) if it is an automatic
transmission/dual clutch transmission
vehicle. The engine starts only when
the shift lever is in N (Neutral) or P
(Park).

[Check the battery connections to be
sure they are clean and tight.

[Turn on the interior light. If the light
dims or goes out when you operate
the starter, the battery is drained.
Do not push or pull the vehicle to start
it. This could cause damage to your
vehicle. See instructions for “Jump
Starting” provided in this chapter.
CAUTION
Push or pull starting the vehicle may
cause the catalytic converter to
overload which can lead to damage to
the emission control system.
If the engine turns over normally
but doesn’t start

[Check the fuel level and add fuel if
necessary.
If the engine still does not start, we
recommend that you call a HYUNDAI
authorised repairer for assistance.
IF THE ENGINE WILL NOT START

8-7
08
i Information
Pb
An inappropriately disposed
battery can be harmful to the
environment and human
health. Dispose of the battery
according to your local law(s)
or regulations.
Jump starting procedure
1. Position the vehicles close enough
that the jumper cables will reach, but
do not allow the vehicles to touch.
2. Avoid fans or any moving parts in the
engine compartment at all times, even
when the vehicles are turned off.
3. Turn off all electrical devices such
as radios, lights, air conditioning,
etc. Put the vehicles in P (Park, for
automatic transmission/dual clutch
transmission vehicle) or neutral (for
manual transmission vehicle), and set
the parking brakes. Turn both vehicles
OFF.1VQA4001
4. Connect the jumper cables in
the exact sequence shown in the
illustration. First connect one jumper
cable to the red, positive (+) jumper
terminal of your vehicle (1).
5. Connect the other end of the jumper
cable to the red, positive (+) battery/
jumper terminal of the assisting
vehicle (2).
6. Connect the second jumper cable to
the black, negative (-) battery/ chassis
ground of the assisting vehicle (3).
7. Connect the other end of the second
jumper cable to the black, negative (-)
chassis ground of your vehicle (4).
Do not allow the jumper cables to
contact anything except the correct
battery or jumper terminals or the
correct ground. Do not lean over the
battery when making connections.
8. Start the engine of the assisting
vehicle and let it run at approximately
2,000rpm for a few minutes. Then
start your vehicle.
If your vehicle will not start after a
few attempts, it probably requires
servicing. In this event, please seek
qualified assistance. If the cause of your
battery discharging is not apparent, we
recommend that you have your vehicle
checked by a HYUNDAI authorised
repairer.

8-13
08
Low tyre pressure
warning light
Low tyre pressure position and
tyre pressure telltale
ONX4E040019
When the tyre pressure monitoring
system warning indicators are
illuminated and a warning message
displayed on the cluster LCD display,
one or more of your tyres is significantly
under-inflated. The Low Tyre Pressure
Position Telltale will indicate which
tyre is significantly underinflated by
illuminating the corresponding position
light.
If either telltale illuminates, immediately
reduce your speed, avoid hard cornering
and anticipate increased stopping
distances. You should stop and check
your tyres as soon as possible. Inflate the
tyres to the proper pressure as indicated
on the vehicle’s placard or tyre inflation
pressure label located on the driver’s
side centre pillar outer panel.If you cannot reach a service station or
if the tyre cannot hold the newly added
air, replace the low pressure tyre with
the spare tyre.
The Low Tyre Pressure Telltale will
remain on and the TPMS Malfunction
Indicator may blink for one minute
and then remain illuminated (when
the vehicle is driven approximately 10
minutes at speed above 15.5 mph (25
km/h)) until you have the low pressure
tyre repaired and replaced on the
vehicle.
CAUTION
In winter or cold weather, the Low Tyre
Pressure Telltale may be illuminated if
the tyre pressure was adjusted to the
recommended tyre inflation pressure
in warm weather. It does not mean
your TPMS is malfunctioning because
the decreased temperature leads to a
proportional lowering of tyre pressure.
When you drive your vehicle from a
warm area to a cold area or from a cold
area to a warm area, or the outside
temperature is greatly higher or lower,
you should check the tyre inflation
pressure and adjust the tyres to the
recommended tyre inflation pressure.
WARNING
Low pressure damage
Significantly low tyre pressure makes
the vehicle unstable and can contribute
to loss of vehicle control and increased
braking distances.
Continued driving on low pressure
tyres can cause the tyres to overheat
and fail.

8-15
08
If the indicators do not extinguish after
a few minutes, it is recommended to
contact the nearest authorised HYUNDAI
dealer.
Each wheel is equipped with a tyre
pressure sensor mounted inside the tyre
behind the valve stem (except for the
spare tyre). You must use TPMS specific
wheels. It is recommended that you
always have your tyres serviced by a
HYUNDAI authorised repairer.
You may not be able to identify a tyre
with low pressure by simply looking at it.
Always use a good quality tyre pressure
gauge to measure. Please note that a
tyre that is hot (from being driven) will
have a higher pressure measurement
than a tyre that is cold.
A cold tyre means the vehicle has been
sitting for 3 hours and driven for less
than 1 mile (1.6 km) in that 3 hour period.
Allow the tyre to cool before measuring
the inflation pressure. Always be sure
the tyre is cold before inflating to the
recommended pressure.
WARNING

[The TPMS cannot alert you to severe
and sudden tyre damage caused by
external factors such as nails or road
debris.

[If you feel any vehicle instability,
immediately take your foot off
the accelerator, apply the brakes
gradually with light force, and slowly
move to a safe position off the road.
WARNING
Tampering with, modifying, or disabling
the Tyre Pressure Monitoring System
(TPMS) components may interfere
with the system’s ability to warn the
driver of low tyre pressure conditions
and/or TPMS malfunctions. Tampering
with, modifying, or disabling the Tyre
Pressure Monitoring System (TPMS)
components may void the warranty for
that portion of the vehicle.
WARNING

[Do not modify the vehicle; it may
interfere with the TPMS function.

[The wheels on the market do not
have a TPMS sensor.

[For your safety, we recommend that
you use parts for replacement from a
HYUNDAI authorised repairer.

[If you use the wheels on the market,
use a TPMS sensor approved by a
HYUNDAI dealer or the equivalent
approved for your vehicle. If your
vehicle is not equipped with a TPMS
sensor or TPMS does not work
properly, you may fail the periodic
vehicle inspection conducted in your
country.

8-39
08
It will also be triggered automatically
when the vehicle is equipped with a TPS
system which does not function in the
event of a severe accident.
The 112-based eCall in-vehicle system
can also be triggered manually, if
needed. Instructions for manual
activation of the system: refer to this
section.
In the event of a critical system failure
that would disable the 112-based eCall
in-vehicle system, the following warning
will be given to the occupants of the
vehicle: refer to this section.
Information on data processing
Any processing of personal data
through the 112-based eCall in-vehicle
system shall comply with the personal
data protection rules provided for in
Directives 95/46/EC (1) and 2002/58/
EC (2) of the European Parliament and
of the Council, and in particular, shall
be based on the necessity to protect
the vital interests of the individuals in
accordance with Article 7(d) of Directive
95/46/EC (3).
Processing of such data is strictly
limited to the purpose of handling the
emergency eCall to the single European
emergency number 112.
Types of data and its recipients
The 112-based eCall in-vehicle system
may collect and process only the
following data:
- Vehicle Identification Number
- Vehicle type (passenger vehicle or light
commercial vehicle)
- Vehicle propulsion storage type
(petrol/diesel/CNG/LPG/electric/
hydrogen)
- Vehicle recent locations and direction
of travel
- Log file of the automatic activation of
the system and its timestamp
- Any additional data (if applicable): Not
applicable
Recipients of data processed by the 112-
based eCall in-vehicle system are the
relevant public safety answering points
designated by the respective public
authorities of the country on which
territory they are located, to first receive
and handle eCalls to the single European
emergency number 112. Additional
information (if available): Not applicable

9
Battery ........................................................................................................... 9-29For best battery service .......................................................................................... 9-30
Battery capacity label .............................................................................................. 9-31
Battery recharging ................................................................................................... 9-31
Reset items .............................................................................................................. 9-32
Tyres and wheels ........................................................................................... 9-33Tyre care ................................................................................................................... 9-33
Recommended cold tyre inflation pressures ........................................................ 9-34
Check tyre inflation pressure ................................................................................. 9-34
Tyre rotation ............................................................................................................. 9-35
Wheel alignment and tyre balance ........................................................................ 9-36
Tyre replacement..................................................................................................... 9-36
Wheel replacement ................................................................................................. 9-38
Tyre traction ............................................................................................................. 9-38
Tyre maintenance .................................................................................................... 9-38
Tyre sidewall labelling ............................................................................................. 9-38
Low aspect ratio tyres ..............................................................................................9-41
Fuses .............................................................................................................. 9-42Instrument panel fuse replacement ...................................................................... 9-43
Engine compartment panel fuse replacement ..................................................... 9-44
Fuse/relay panel description .................................................................................. 9-45
Light bulbs .....................................................................................................9-59Headlight, Position Light, Turn signal Light bulb replacement ............................9-60
Headlight and front fog light aiming (For Europe) ................................................ 9-65
Side repeater light replacement ............................................................................ 9-70
Rear combination light bulb replacement ............................................................. 9-71
High mounted stop light replacement .................................................................. 9-78
License plate light bulb replacement .................................................................... 9-78
Interior light bulb replacement .............................................................................. 9-79
Appearance care .......................................................................................... 9-80Exterior care ............................................................................................................9-80
Interior care ............................................................................................................. 9-85
Emission control system.............................................................................. 9-88Crankcase emission control system ......................................................................9-88
Evaporative emission control system ....................................................................9-88
Exhaust emission control system ...........................................................................9-89

9-8
Maintenance
Whilst operating your vehicle:

[Note any changes in the sound of the
exhaust or any smell of exhaust fumes
in the vehicle.

[Check for vibrations in the steering
wheel. Notice if there is any increased
steering effort or looseness in the
steering wheel, or change in its
straight-ahead position.

[Notice if your vehicle constantly turns
slightly or “pulls” to one side when
travelling on smooth, level road.

[When stopping, listen and check for
unusual sounds, pulling to one side,
increased brake pedal travel or “hard-
to-push” brake pedal.

[If any slipping or changes in the
operation of your transmission occurs,
check the transmission fluid level.

[Check the parking brake.

[Check for fluid leaks under your
vehicle (water dripping from the air
conditioning system during or after
use is normal).
At least monthly:

[Check coolant level in the engine
coolant reservoir.

[Check the operation of all exterior
lights, including the stoplights, turn
signals and hazard warning flashers.

[Check the inflation pressures of all
tyres including the spare for tyres that
are worn, show uneven wear, or are
damaged.

[Check for loose wheel lug nuts.
At least twice a year:
(i.e., every Spring and Autumn)

[Check radiator, heater and air
conditioning hoses for leaks or
damage.

[Check windscreen washer spray and
wiper operation. Clean wiper blades
with a clean cloth dampened with
washer fluid.

[Check headlight alignment.

[Check muffler, exhaust pipes, shields
and clamps.

[Check the seat belts for wear and
function.
At least once a year:

[Clean body and door drain holes.

[Lubricate door hinges and bonnet
hinges.

[Lubricate door and bonnet locks and
latches.

[Lubricate door rubber weather strips.

[Lubricate door checker

[Check the air conditioning system.

[Inspect and lubricate automatic
transmission linkage and controls.

[Clean the battery and terminals.

[Check the brake fluid level.

9-28
Maintenance
Rear window wiper blade
(if equipped)
OLMB073023
1. Raise the wiper arm and rotate the
wiper blade assembly (1).
2. Pull out the wiper blade assembly.
OLMB073024
3. Install the new blade assembly by
inserting the centre part into the slot
in the wiper arm until it clicks into
place.
4. Make sure the blade assembly is
installed firmly by trying to pull it
slightly.
To prevent damage to the wiper arms
or other components, we recommend
that the wiper blade be replaced by a
HYUNDAI authorised repairer.

9-31
09
%DWWHU\FDSDFLW\ODEHO
OBC3090062
„ Example
❈ The actual battery label in the vehicle
may differ from the illustration.
1. AGM50L-DIN : The HYUNDAI model
name of battery
2. 12V : The nominal voltage
3. 50Ah (20HR) : The nominal capacity
(in Ampere hours)
4. RC 80 : The nominal reserve capacity
(in min.)
5. CCA 560A : Cold-test current in
amperes by SAE/EN
%DWWHU\UHFKDUJLQJ
Your vehicle has a maintenance-free,
calcium-based battery.

[ ,IWKHEDWWHU\EHFRPHVGLVFKDUJHG
over a short time (for example, the
headlights or interior lights were on
whilst the vehicle was not in use),
recharge it by slow charging (trickle)
for 10 hours.

[ ,IWKHEDWWHU\JUDGXDOO\GLVFKDUJHV
because of high electrical load whilst
the vehicle is being used, recharge it
at 20-30A for two hours.
WARNING
When recharging the battery, observe
the following precautions:

[ %HIRUHSHUIRUPLQJPDLQWHQDQFHRU
recharging the battery, turn off all
accessories and stop the engine.

[Do not allow cigarettes, sparks, or
flame near the battery.

[Wear eye protection when checking
the battery during charging.

[The battery must be removed from
the vehicle and placed in an area with
good ventilation.

[Watch the battery during charging,
and stop or reduce the charging
rate if the battery cells begin
gassing (boiling) violently or if the
temperature of the electrolyte of any
cell exceeds 49°C (120°F).

[The negative battery cable must be
removed first and installed last when
the battery is disconnected.

[Disconnect the battery charger in the
following order.
1. Turn off the main battery charger
switch.
2. Unhook the negative clamp from
the negative battery terminal.
3. Unhook the positive clamp from
the positive battery terminal.