light HYUNDAI I20 2023 Owners Manual
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2023, Model line: I20, Model: HYUNDAI I20 2023Pages: 649, PDF Size: 12.35 MB
Page 600 of 649
9-41
09
7 H P S H U D W X U H $ % &
The temperature grades are A (the
highest), B and C representing the tyre’s
resistance to the generation of heat
and its ability to dissipate heat when
tested under controlled conditions on a
specified indoor laboratory test wheel.
Sustained high temperature can cause
the material of the tyre to degenerate
and reduce tyre life, and excessive
temperature can lead to sudden tyre
failure. Grades B and A represent higher
levels of performance on the laboratory
test wheel than the minimum required
by law.
WARNING
The temperature grade for this tyre is
established for a tyre that is properly
inflated and not overloaded. Excessive
speed, under-inflation, over-inflation,
or excessive loading, either separately
or in combination, can cause heat
build-up and possible sudden tyre
failure. This may cause loss of vehicle
control resulting in an accident.
Low aspect ratio tyres
Low aspect ratio tyres, the aspect ratio
is lower than 50, are provided for sporty
looks.
Because low aspect ratio tyres are
optimized for handling and braking, their
sidewall is a little stiffer than a standard
tyre. Also, low aspect ratio tyres tend to
be wider so that they consequently have
a greater contact patch with the road
surface. In some instances, they may
generate more road noise compared
with standard tyres.
CAUTION
% H F D X V H W K H V L G H Z D O O R I D O R Z D V S H F W
ratio tyre is shorter than a standard
tyre, the rim of the wheel and the
tyre itself are more easily more easily
susceptible to damage. Use caution
when driving and follow the guidelines
below to help minimise damage to the
wheel and tyre:
[ : K H Q G U L Y L Q J R Q D U R X J K U R D G R U
driving off a road, be careful not to
damage the tyres and wheels. After
driving, inspect the tyres and wheels.
[ : K H Q S D V V L Q J R Y H U D S R W K R O H V S H H G
bump, manhole, or kerb stone,
drive the vehicle slowly so as not to
damage the tyres and wheels.
[ , I W K H W \ U H L V V X E M H F W H G W R D V H Y H U H
impact, we recommend you have
the tyre and wheel inspected by a
HYUNDAI authorised repairer.
[ , Q V S H F W W K H W \ U H F R Q G L W L R Q D Q G
pressure every 3,000 km (1,800 miles)
to prevent tyre damage.
[ , W L V Q R W H D V \ W R U H F R J Q L V H W \ U H
G D P D J H Z L W K \ R X U R Z Q H \ H V % X W
if there is the slightest hint of tyre
damage, have the tyre checked or
replaced because the tyre damage
may cause air leakage from the tyre.
[ , I W K H W \ U H L V G D P D J H G E \ G U L Y L Q J
on a rough road, off road, pothole,
manhole, or kerb stone, it will not be
covered by the warranty.
Page 601 of 649
9-42
Maintenance
OTA070039
„ Blade type
NormalBlown
„ Cartridge type
„ Multi fuse
NormalBlown
NormalBlown
A vehicle’s electrical system is protected
from electrical overload damage by
fuses.
This vehicle has 2 (or 3) fuse panels, one
located in the driver’s side panel bolster,
the other in the engine compartment.
If any of your vehicle’s lights,
accessories, or controls do not work,
check the appropriate circuit fuse. If a
fuse has blown, the element inside the
fuse will be melted or broken.
If the electrical system does not work,
first check the driver’s side fuse panel.
Before replacing a blown fuse, turn the
engine and all switches off, and then
disconnect the negative battery cable.
Always replace a blown fuse with one of
the same rating.
If the replacement fuse blows, this
indicates an electrical problem. Avoid
using the system involved and we
recommend that all inspect a HYUNDAI
authorised repairer.
i Information
7 K U H H N L Q G V R I I X V H V D U H X V H G E O D G H W \ S H
I R U O R Z H U D P S H U D J H U D W L Q J V F D U W U L G J H
W \ S H D Q G P X O W L I X V H I R U K L J K H U D P S H U D J H
U D W L Q J V
WARNING
NEVER replace a fuse with anything but
another fuse of the same rating.
[ A higher capacity fuse could cause
damage and possibly cause a fire.
[ Do not install a wire or aluminium
foil instead of the proper fuse -
even as a temporary repair. It may
cause extensive wiring damage and
possibly a fire.
NOTICE
Do not use a screwdriver or any other
metal object to remove fuses because
it may cause a short circuit and damage
the system.
FUSES
Page 602 of 649
9-43
09
Instrument panel fuse
replacement
OBC3N091016AU
1. Turn the vehicle off.
2. Turn all other switches OFF.
3. Open the fuse panel cover.
4. Refer to the label on the inside of
the fuse panel cover to locate the
suspected broken fuse location.
OBC3N091018AU
5. Pull the suspected fuse straight out.
Use the removal tool provided in the
engine compartment fuses panel.
6. Check the removed fuse; replace it if
it is blown. Spare fuses are provided in
the instrument panel fuse panels (or in
the engine compartment fuse panel).
7. Push in a new fuse of the same rating,
and make sure it fits tightly in the
clips.If it fits loosely, we recommend
that you consult with a HYUNDAI
authorised repairer.
In an emergency, if you do not have a
spare fuse, use a fuse of the same rating
from a circuit such as the cigarette
lighter fuse.
If the headlights or other electrical
components do not work and the fuses
are undamaged, check the fuse panel
in the engine compartment. If a fuse
is blown, it must be replaced with the
same rating.
Page 618 of 649
9-59
09
We recommend that you consult with a
HYUNDAI authorised repairer to replace
most vehicle light bulbs. It is difficult
to replace vehicle light bulbs because
other parts of the vehicle must be
removed before you can get to the bulb.
This is especially true for removing the
headlight assembly to get to the bulb(s).
Removing/installing the headlight
assembly can result in damage to the
vehicle.
WARNING
Prior to replacing a light, depress the
foot brake, move the shift lever into the
N (Neutral, for automatic transmission
vehicle) or neutral (for manual
transmission vehicle), apply the parking
brake, place the ignition switch in the
LOCK/OFF position, and take the key
with you when leaving the vehicle to
avoid sudden movement of the vehicle
and to prevent possible electric shock.
% H D Z D U H W K H E X O E V P D \ E H K R W D Q G P D \
burn your fingers.
NOTICE
% H V X U H W R U H S O D F H W K H E X U Q H G R X W E X O E
with one of the same wattage rating.
Otherwise, it may cause damage to the
fuse or electric wiring system.
i Information
7 K H K H D G O L J K W D Q G W D L O O D P S O H Q V H V F R X O G
D S S H D U I U R V W \ L I W K H Y H K L F O H L V Z D V K H G D I W H U
G U L Y L Q J R U W K H Y H K L F O H L V G U L Y H Q D W Q L J K W
L Q Z H W Z H D W K H U 7 K L V F R Q G L W L R Q L V F D X V H G
E \ W H P S H U D W X U H G L I I H U H Q F H E H W Z H H Q W K H
O D P S L Q V L G H D Q G R X W V L G H D Q G L W G R H V Q R W
L Q G L F D W H D S U R E O H P Z L W K \ R X U Y H K L F O H
: K H Q P R L V W X U H F R Q G H Q V H V L Q W K H O D P S
L W Z L O O E H U H P R Y H G D I W H U G U L Y L Q J Z L W K W K H
K H D G O L J K W R Q 7 K H U H P R Y D E O H O H Y H O P D \
G L I I H U G H S H Q G L Q J R Q O D P S V L ] H O D P S
S R V L W L R Q D Q G H Q Y L U R Q P H Q W D O F R Q G L W L R Q
+ R Z H Y H U L I P R L V W X U H L V Q R W U H P R Y H G Z H
U H F R P P H Q G W K D W \ R X U Y H K L F O H L V L Q V S H F W H G
E \ D + < 8 1 ' $ , D X W K R U L V H G U H S D L U H U
i Information (For Europe)
7 U D I I L F & K D Q J H
7 K H O R Z E H D P O L J K W G L V W U L E X W L R Q L V
D V \ P P H W U L F , I \ R X J R D E U R D G W R D F R X Q W U \
Z L W K R S S R V L W H W U D I I L F G L U H F W L R Q W K L V
D V \ P P H W U L F S D U W Z L O O G D ] ] O H R Q F R P L Q J F D U
G U L Y H U 7 R S U H Y H Q W G D ] ] O H ( & ( U H J X O D W L R Q
G H P D Q G V V H Y H U D O W H F K Q L F D O V R O X W L R Q V H [
D X W R P D W L F F K D Q J H V \ V W H P D G K H V L Y H V K H H W
G R Z Q D L P L Q J 7 K H V H K H D G O L J K W V D U H
G H V L J Q H G Q R W W R G D ] ] O H R S S R V L W H G U L Y H U V
6 R \ R X Q H H G Q R W F K D Q J H \ R X U K H D G O L J K W V
L Q D F R X Q W U \ Z L W K W K H R S S R V L W H W U D I I L F
G L U H F W L R Q
LIGHT BULBS
Page 619 of 649
9-60
Maintenance
Headlight, Position Light,
Turn signal Light bulb
replacement
Type A
OBC3N090030
(1) Headlight (Low/High)
(2) Turn signal light
(3) Position light (if equipped)
(4) Daytime running light/
D.R.L & Position
Type B -N line
OBC3TN091003
(1) Headlight (Low/High)
(2) Turn signal light
(3) Daytime running light & Position light
Type C - CUV
OBC3V091001
(1) Headlight(Low/High)
(2) Turn signal light
(3) Daytime running light & Position light
*1 : MFR (Multi Focus Reflector) Headlight
Page 620 of 649
9-61
09
OLMB073042L
WARNING
[ Handle halogen bulbs with care.
Halogen bulbs contain pressurized
gas that will produce flying pieces
of glass that could cause injuries if
broken.
[ Wear eye protection when changing
a bulb. Allow the bulb to cool down
before handling it.
[ Always handle them carefully, and
avoid scratches and abrasions. If
the bulbs are lit, avoid contact with
liquids.
[ Never touch the glass with bare
hands. Residual oil may cause the bulb
to overheat and burst when lit.
[ A bulb should be operated only when
installed in a headlight.
[ If a bulb becomes damaged or
cracked, replace it immediately and
carefully dispose of it.
i Information
: H U H F R P P H Q G W K D W W K H K H D G O L J K W D L P L Q J
E H D G M X V W H G D I W H U D Q D F F L G H Q W R U D I W H U W K H
K H D G O L J K W D V V H P E O \ L V U H L Q V W D O O H G
❈ 7 U D I I L F & K D Q J H ) R U ( X U R S H
The low beam light distribution is
asymmetric. If you go abroad to a
country with opposite traffic direction,
this asymmetric part will dazzle
oncoming car driver. To prevent dazzle,
ECE regulation demands several
technical solutions (ex. automatic
change system, adhesive sheet, down
aiming). This headlamps are designed
not to dazzle opposite drivers.
So, you need not change your
headlamps in a country with the
opposite traffic direction.
Page 621 of 649
9-62
Maintenance
+ H D G O L J K W / R Z + L J K
1. Turn the front wheel at inwards.
OAC3089042TU
OAC3089043TU
OBC3090055
2. Remove the Wheel guard clips (B),
bumper cover bolt (A) and bumper
upper cover blots (C).
3. Push the wheel guard aside and
remove the headlight bulb cover by
turning it counterclockwise from bulb
assembly.
OBC3090038
OBC3TN091005
„CUV
4. Disconnect the headlight bulb socket-
connector.
5. Unsnap the headlight bulb retaining
wire by depressing the end and
pushing it upward.
6. Remove the bulb from the headlight
assembly.
7. Install a new headlight bulb and snap
the headlight bulb retaining wire into
position by aligning the wire with the
groove on the bulb.
8. Connect the headlight bulb socket
connector.
9. Install the headlight bulb cover by
turning it clockwise.
10. Install the wheel guard in the reverse
order.
Page 622 of 649
9-63
09
OBC3090039
OBC3TN091006
„CUV
7 X U Q V L J Q D O O L J K W
1. Open the bonnet.
2. Remove the turn signal light or low
beam assist-static light bulb cover by
turning it counterclockwise.
3. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
4. Insert a new bulb by inserting it into
the socket and rotating it until it locks
into place.
5. Install the socket in the assembly by
aligning the tabs on the socket with
the slots in the assembly.
Push the socket into the assembly and
turn the socket clockwise.
6. Install the turn signal light or low
beam assist-static light bulb cover by
turning it clockwise.
3 R V L W L R Q O L J K W ' D \ W L P H U X Q Q L Q J O L J K W
L I H T X L S S H G
If the LED lamp does not operate,
we recommend that the system be
inspected by a HYUNDAI authorised
repairer.
The LED lamps cannot be replaced as
a single unit because it is an integrated
unit. The LED lamp has to be replaced
with the unit. Unless a skilled technician
checks or repairs the LED lamp, it may
damage related parts of the vehicle.
Page 623 of 649
9-64
Maintenance
Type D (LED)
OBC3090037
Type E (LED)-N line
OBC3TN091001
(1) headlight (Low)
(2) headlight (High)
(3) Static Bending Light
(4) Turn signal light
(5) Daytime running light & Position light
(6) Front fog light
Type F (LED)-CUV
OBC3V091005
(1) Headlight (Low)
(2) Headlight (High)
(3) Static Bending Light
(4) Daytime running light & Position &
Turn signal light
+ H D G O L J K W 3 R V L W L R Q O L J K W 7 X U Q V L J Q D O
O L J K W ' D \ W L P H U X Q Q L Q J O L J K W / R Z
E H D P D V V L V W V W D W L F O L J K W E X O E U H S O D F H
P H Q W
If the LED lamp does not operate,
we recommend that the system be
inspected by a HYUNDAI authorised
repairer. The LED lamps cannot be
replaced as a single unit because it is an
integrated unit. The LED lamp has to be
replaced with the unit.
Unless a skilled technician checks or
repairs the LED lamp, it may damage
related parts of the vehicle.
Page 624 of 649
9-65
09
„Front Fog light
OBC3090040
) R J O L J K W L I H T X L S S H G
1. Remove the under cover by rotating
the screws and bolts.
2. Reach your hand into the back of the
front bumper.
3. Disconnect the power connector from
the socket.
4. Remove the bulb-socket from
the housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
housing.
5. Install the new bulb-socket into the
housing by aligning the tabs on the
socket with the slots in the housing.
Push the socket into the housing and
turn the socket clockwise.
6. Connect the power connector to the
socket.
7. Reinstall the front bumper under
cover.
Headlight and front fog light
aiming (For Europe, if equipped)
Headlight aiming
„Type A
OBC3090041
„Type B
OBC3090057
„Type C
OBC3TN091004
1. Inflate the tyres to the specified
pressure and remove any loads from
the vehicle except the driver, spare
tyre, and tools.
2. The vehicle should be placed on a flat
floor.