ESP HYUNDAI I20 2023 User Guide
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2023, Model line: I20, Model: HYUNDAI I20 2023Pages: 649, PDF Size: 12.35 MB
Page 86 of 649
3-49
03
During a frontal collision, sensors will
detect the vehicle’s deceleration. If the
rate of deceleration is high enough, the
control unit will inflate the front air bags,
at the time and with the force needed.
The front air bags help protect the driver
and front passenger by responding to
frontal impacts in which seat belts alone
cannot provide adequate restraint. When
needed, the side air bags help provide
protection in the event of a side impact.
[ Air bags are activated (able to inflate
if necessary) only when the ignition
switch is in the ON position.
[ Air bags inflate in the event of certain
frontal or side collisions to help
protect the occupants from serious
physical injury.
[ Generally, air bags are designed to
inflate based upon the severity of a
collision and it’s direction etc. These
two factors determine whether
the sensors produce an electronic
deployment/inflation signal.
[ The front air bags will completely
inflate and deflate in an instant. It is
virtually impossible for you to see the
air bags inflate during an accident. It is
much more likely that you will simply
see the deflated air bags hanging out
of their storage compartments after
the collision.[ To help provide protection, the air
bags must inflate rapidly. The speed
of air bag inflation is a consequence
of extremely short time in which
to inflate the air bag between the
occupant and the vehicle structures
before the occupant impacts those
structures. This speed of inflation
reduces the risk of serious or life-
threatening injuries and is thus a
necessary part of air bag design.
However, the rapid air bag inflation
can also cause injuries which can
include facial abrasions, bruises and
broken bones because the inflation
speed also causes the air bags to
expand with a great deal of force.
[ There are even circumstances under
which contact with the air bag can
cause fatal injuries, especially if the
occupant is positioned excessively
close to the air bag.
You can take steps to reduce the risk of
being injured by an inflating air bag. The
greatest risk is sitting too close to the air
bag. An air bag needs space to inflate.
It is recommended that drivers sit as far
as possible between the centre of the
steering wheel and the chest whilst still
maintaining control of the vehicle.
Page 118 of 649
4-23
04
Lights mode
OIK047163L
This indicator displays which exterior
light is selected using the lighting
control.
Wiper mode
OCN7040039L
This indicator displays which wiper
speed is selected using the wiper
control.
Low pressure
ONX4E040019
This warning message is displayed if the
tyre pressure is low. The corresponding
tyre on the vehicle will be illuminated.
For more details, refer to “Tyre Pressure
Monitoring System (TPMS)” section in
chapter 8.
Heated Steering Wheel turned off
(if equipped)
This message illuminates if the heated
steering wheel will turn off automatically
approximately 30 minutes after the
heated steering wheel is turned on.
For more details, refer to “Heated
Steering Wheel” in chapter 5.
Low fuel
This warning message is displayed if the
fuel tank is almost out of fuel.
When this message is displayed, the low
fuel level warning light in the cluster will
come on.
It is recommended to look for the
nearest fuelling station and refuel as
soon as possible.
Page 119 of 649
4-24
Instrument cluster
Low engine oil (if equipped)
This warning message is displayed when
the engine oil level should be checked.
If this warning message is displayed,
check the engine oil level as soon as
possible and add engine oil as required.
Slowly pour the recommended oil little
by little into a funnel.
Use only the specified engine oil. (Refer
to "Recommended lubricants and
capacities" section in chapter 2.)
Do not overfill the engine oil. Make sure
the oil level is not above F (Full) mark on
the dipstick.
NOTICE
If the message is displayed
continuously after adding the engine
oil and travelling approximately 31~
62 mile (50~100 km) after the engine
warms up, we recommend that the
system be checked by a HYUNDAI
authorised repairer.
Engine has overheated
(if equipped)
This warning message is displayed
when the engine coolant temperature
is above 120°C (248°F). This means that
the engine is overheated and may be
damaged.
If your vehicle is overheated, refer to
“Overheating” section in chapter 8.
Check headlight (if equipped)
This warning message is displayed if the
headlamps are not operating properly.
In addition, if a specific lamp(turn signal
lamp etc.) is not operating properly, the
warning message according to a specific
lamp (turn signal lamp etc.) is displayed.
A corresponding bulb may need to be
replaced.
Make sure to replace the burned out
bulb with a new one of the same
wattage rating.
Check brake light (if equipped)
This warning message is displayed if the
stop lamps are not operating properly. A
lamp may need to be replaced.
Make sure to replace the burned out
bulb with a new one of the same
wattage rating.
Check Active Air Flap system (if
equipped)
This message is displayed in the
following situations:
- There is a malfunction with the
actuator flap
- There is a malfunction with the
actuator air flap controller
- The air flap does not open
When all of the above conditions are
fixed, the warning will disappear.
Page 147 of 649
5-6
Convenient features
Remote key precautions
The remote key will not work if any of
the following occurs:
[ The key is in the ignition switch.
[ You exceed the operating distance
limit (about 30 m [90 feet]).
[ The remote key battery is weak.
[ Other vehicles or objects may be
blocking the signal.
[ The weather is extremely cold.
[ The remote key is close to a radio
transmitter such as a radio station or
an airport which can interfere with
normal operation of the remote key.
When the remote key does not work
correctly, open and close the door
with the mechanical key. If you have
a problem with the remote key, it is
recommended that you contact a
HYUNDAI authorised repairer.
If the remote key is in close proximity to
your mobile phone, the signal could be
blocked by your mobile phone's normal
operational signals. This is especially
important when the phone is active
such as making and receiving calls, text
messaging, and/or sending/receiving
emails. Avoid placing the remote key
and your mobile phone in the same
pants or jacket pocket and always try to
maintain an adequate distance between
the two devices.i Information
Changes or modifications not expressly
approved by the party responsible
for compliance could void the user’s
D X W K R U L W \ W R R S H U D W H W K H H T X L S P H Q W , I W K H
keyless entry system is inoperative due
to changes or modifications not expressly
approved by the party responsible for
compliance, it will not be covered by your
manufacturer’s vehicle warranty.
NOTICE
. H H S W K H U H P R W H N H \ D Z D \ I U R P
electromagnetic materials that blocks
electromagnetic waves to the key
surface.
Page 152 of 649
5-11
05
Smart key precautions
The smart key will not work if any of the
following occurs:
[ The smart key is close to a radio
transmitter such as a radio station or
an airport which can interfere with
normal operation of the transmitter.
[ The smart key is near a mobile two
way radio system or a mobile phone.
[ $ Q R W K H U Y H K L F O HT V V P D U W N H \ L V E H L Q J
operated close to your vehicle.
When the smart key does not work
correctly, open and close the door
with the mechanical key. If you have
a problem with the smart key, it is
recommended that you contact a
HYUNDAI authorised repairer.
If the smart key is in close proximity to
your mobile phone, the signal could be
blocked by your mobile phone's normal
operational signals. This is especially
important when the phone is active
such as making and receiving calls, text
messaging, and/or sending/receiving
emails. Avoid placing the smart key and
your mobile phone in the same pants or
jacket pocket and always try to maintain
an adequate distance between the two
devices.
i Information
Changes or modifications not expressly
approved by the party responsible
for compliance could void the user’s
D X W K R U L W \ W R R S H U D W H W K H H T X L S P H Q W , I W K H
keyless entry system is inoperative due
to changes or modifications not expressly
approved by the party responsible for
compliance, it will not be covered by your
manufacturer’s vehicle warranty.
NOTICE
. H H S W K H V P D U W N H \ D Z D \ I U R P
electromagnetic materials that blocks
electromagnetic waves to the key
surface.
Battery replacement
OLF044008
If the Smart Key is not working properly,
try replacing the battery with a new one.
Battery Type: CR2032
To replace the battery:
1. Pry open the rear cover of the smart
key.
2. Remove the old battery and insert the
new battery. Make sure the battery
position is correct.
3. Reinstall the rear cover of the smart
key.
If you suspect your smart key might
have sustained some damage, or you
feel your smart key is not working
correctly, it is recommended that you
contact a HYUNDAI authorised repairer.
i Information
An inappropriately disposed
battery can be harmful to the
environment and human
K H D O W K ' L V S R V H W K H E D W W H U \
according to your local law(s)
and regulation.
Page 180 of 649
5-39
05
Emergency tailgate safety
release
OIB047188
Your vehicle is equipped with the
emergency tailgate safety release lever
located on the bottom of the tailgate.
When someone is inadvertently locked
in the luggage compartment, the tailgate
can be opened by doing as follows:
1. Input the mechanical key into the hole.
2. Push the mechanical key to the right.
3. Push up the tailgate.
WARNING
[ ) R U H P H U J H Q F L H V E H I X O O \ D Z D U H
of the location of the emergency
tailgate safety release lever in the
vehicle and how to open the tailgate
if you are accidentally locked in the
luggage compartment.
[ No one should be allowed to occupy
the luggage compartment of the
vehicle at any time. The luggage
compartment is a very dangerous
location in the event of a crash.
[ Use the release lever for emergencies
only. Use with extreme caution,
especially while the vehicle is in
motion.
) X H O I L O O H U G R R U
Opening the fuel filler door
OBC3050027
1. Turn the engine off.
( Q V X U H W K H G U L Y H UT V G R R U L V X Q O R F N H G
3. Push the fuel filler door near the 3
o‘clock position.
Page 182 of 649
5-41
05
[ Do not get back into a vehicle
once you have begun refuelling.
You can generate a build-up of
static electricity by touching,
rubbing or sliding against any item
or fabric capable of producing
static electricity. Static electricity
discharge can ignite fuel vapours
causing a fire. If you must re-enter
the vehicle, you should once again
eliminate potentially dangerous
static electricity discharge by
touching a metal part of the vehicle,
away from the fuel filler neck, nozzle
or other petrol source, with your bare
hand.
[ When refuelling, always move the
shift lever to the N (Neutral, for
Automatic transmission/Dual clutch
transmission) or the first gear or R
(Reverse, for Manual transmission)
position, set the parking brake,
and place the ignition switch to the
/ 2 & . 2 ) ) S R V L W L R Q 6 S D U N V S U R G X F H G
by electrical components related to
the engine can ignite fuel vapours
causing a fire.
[ When using an approved portable
fuel container, be sure to place
the container on the ground prior
to refuelling. Static electricity
discharge from the container can
ignite fuel vapours causing a fire.
Once refuelling has begun, contact
between your bare hand and the
vehicle should be maintained until
the filling is complete.
[ Use only approved portable plastic
fuel containers designed to carry and
store petrol.[ Do not use matches or a lighter and
do not smoke or leave a lit cigarette
in your vehicle whilst at a gas station,
especially during refuelling.
[ Do not over-fill or top-off your
vehicle tank, which can cause petrol
spillage.
[ If a fire breaks out during refuelling,
leave the vicinity of the vehicle, and
immediately contact the manager
of the gas station and then contact
W K H O R F D O I L U H G H S D U W P H Q W ) R O O R Z D Q \
safety instructions they provide.
[ If pressurized fuel sprays out, it can
cover your clothes or skin and thus
subject you to the risk of fire and
burns. Always remove the fuel cap
carefully and slowly. If the cap is
venting fuel or if you hear a hissing
sound, wait until the condition stops
before completely removing the cap.
[ Always check that the fuel cap is
installed securely to prevent fuel
spillage in the event of an accident.
i Information
0 D N H V X U H W R U H I X H O \ R X U Y H K L F O H
D F F R U G L Q J W R W K H
Page 188 of 649
5-47
05
NOTICE
If the driver exits the vehicle through
another door besides the driver
door, the battery saver function
does not operate and the headlight
G H O D \ I X Q F W L R Q G R H V Q R W W X U Q 2 ) )
automatically.
This may cause the battery to
discharge. To avoid battery discharge,
W X U Q 2 ) ) W K H K H D G O L J K W V P D Q X D O O \ I U R P
the headlight switch before exiting the
vehicle.
Daytime running light (DRL)
(if equipped)
The Daytime Running Lights (DRL) can
make it easier for others to see the front
of your vehicle during the day, especially
after dawn and before sunset.
The DRL system will turn the dedicated
light OFF when:
1. The parking brake is applied.
2. The engine is turned off.
Headlight levelling device
OBC3050009R
To adjust the headlight beam level
according to the number of the
passengers and loading weight in the
luggage area, turn the beam levelling
switch.
The higher the number on the switch
position, the lower the headlight beam
level. Always keep the headlight beam
at the proper levelling position, or
headlights may dazzle other road users.
Listed below are examples of
appropriate switch settings for varying
loads. For loading conditions other than
those listed, adjust the switch position to
the most similar situation.
Loading conditionSwitch position
Driver only0
Driver + Front
passenger0
Full passengers
(including driver)1
Full passengers
(including driver) +
Maximum permissible
loading2
Driver + Maximum
permissible loading 3
Page 192 of 649
5-51
05
2. When the front view camera is
adversely affected by an external
condition. Such examples may
include:
[ When the vehicle’s headlights have
been damaged or not repaired
properly
[ When the vehicle headlights are not
aimed properly
[ When the vehicle is driven on a
narrow curved road or rough road
[ When the vehicle is driven on an
uphill road or downhill road
[ When only part of the vehicle in front
is visible on a crossroad or curved
road
[ When there is a traffic light,
reflecting sign, flashing sign or mirror
[ When the road conditions are bad
such as being wet or covered with
snow
[ When a vehicle suddenly appears
from a curve
[ When the vehicle is tilted from a flat
tyre or being towed
[ : K H Q / D Q H . H H S L Q J $ V V L V W V \ V W H P
warning light illuminates
[ When the light from the oncoming or
front vehicle is not detected because
of exhaust fume, smoke, fog, snow,
etc.
[ When the front window is covered
with foreign matters such as ice,
dust, fog, or is damaged
3. When the forward visibility is poor.
Such examples may include:
[ When the headlights of an oncoming
vehicle or a vehicle in front is not
detected due to poor outside
visibility (smog, smoke, dust, fog,
heavy rain, snow, etc.)
[ When the windscreen visibility is
poor WARNING
[ 7 K H I X Q F W L R Q P D \ Q R W Z R U N D U R X Q G
seconds after starting the vehicle or
the initialization or rebooting of the
front view camera.
[ ' R Q R W D W W H P S W W R G L V D V V H P E O H
the front view camera without the
assistance of a HYUNDAI authorised
repairer technician.
If the front view camera is removed
for any reason, the system may need
to be re-calibrated. We recommend
that the system be inspected by a
HYUNDAI authorised repairer.
[ , I W K H Z L Q G V F U H H Q R I \ R X U Y H K L F O H
is replaced, most likely the front
view camera will need to be
re-calibrated. If this occurs, have
your vehicle inspected and have the
system re-calibrated by a HYUNDAI
authorised repairer.
[ % H F D U H I X O W K D W Z D W H U G R H V QT W J H W L Q W R
front view camera unit and do not
remove or damage related parts of
High Beam Assist system.
[ ' R Q R W S O D F H R E M H F W V R Q W K H F U D V K
pad that reflect light such as mirrors,
white paper, etc. The system may
malfunction if sunlight is reflected.
[ $ W W L P H V + L J K % H D P $ V V L V W P D \
not work properly. The system is
for your convenience only. It is the
responsibility of the driver for safe
driving practices and always check
the road conditions for your safety.
[ : K H Q W K H V \ V W H P G R H V Q R W R S H U D W H
normally, change the light position
manually between the high beam and
low beam.
Page 218 of 649
5-77
05
WARNING
Windscreen heating
Do not use the
or position
during cooling operation in extremely
humid weather. The difference
between the temperature of the
outside air and that of the windscreen
could cause the outer surface of the
windscreen to fog up, causing loss of
visibility. In this case, set the mode
selection knob or button to the
position and fan speed control knob or
button to lower speed.
[ ) R U P D [ L P X P G H I U R V W S H U I R U P D Q F H
set the temperature control knob
to the highest temperature setting
(rotated all the way to the right) and
the fan speed control to the highest
setting.
[ , I Z D U P D L U W R W K H I O R R U L V G H V L U H G
whilst defrosting or defogging, set the
mode to the floor-defrost position.
[ % H I R U H G U L Y L Q J F O H D U D O O V Q R Z D Q G L F H
from the windscreen, rear window,
outside rear view mirrors, and all side
windows.
[ & O H D U D O O V Q R Z D Q G L F H I U R P W K H
bonnet and air inlet in the cowl grill
to improve heater and defroster
efficiency and to reduce the
probability of fogging up inside of the
windscreen.
i Information
, I W K H H Q J L Q H W H P S H U D W X U H L V V W L O O F R O G D I W H U
starting, then a brief engine warm up
period may be required for the vented air
flow to become warm or hot.
Manual climate control system
To defog inside windscreen
OBC3050118
1. Select any fan speed except
"0"position.
2. Select the desired temperature.
3. Select the
or position.
4. The outside (fresh) air will be selected
automatically. Additionally, the
air conditioning (if equipped) will
automatically operate if the mode is
selected to the
position.
If the air conditioning and outside
(fresh) air position are not selected
automatically, press the corresponding
button manually.
WINDSCREEN DEFROSTING AND DEFOGGING