FRONT HYUNDAI I20 2023 Owner's Manual

3-17
03
OBC3030010R
Whilst the engine is running, push either
of the switches to warm the driver’s seat
or front passenger’s seat.
During mild weather or under conditions
where the operation of the seat warmer
is not needed, keep the switches in the
OFF position.

[Each time you push the switch, the
temperature setting of the seat is
changed as follows:


OFFJHIGH ()JMIDDLE ()JLOW ()
K

[The seat warmer defaults to the OFF
position whenever the ignition switch
is turned on.

[When pressing the switch for more
than 1.5 seconds with the seat warmer
operating, the seat warmer will turn
OFF.
Rear Occupant Alert (ROA)
(if equipped)
Rear Occupant Alert is provided to help
prevent the driver from leaving the
vehicle with the rear passenger left in
the vehicle.
System setting
To use Rear Occupant Alert, it must be
enabled from the Settings menu in the
infotainment system screen. Select:
 6HWXS

3-19
03
SEAT BELTS
This section describes how to use the
seat belts properly. It also describes
some of the things not to do when using
seat belts.
Seat belt safety precautions
Always fasten your seat belt and make
sure all passengers have fastened their
seat belts before starting any trip.
Air bags (if equipped) are designed
to supplement the seat belt as an
additional safety device, but they are
not a substitute. Most countries require
all occupants of a vehicle to wear seat
belts.
WARNING
Seat belts must be used by ALL
passengers whenever the vehicle is
moving. Take the following precautions
when adjusting and wearing seat belts:

[ALWAYS properly restrain children
under age 13 in the rear seats.

[NEVER allow children to ride in the
front passenger seat. If a child age 13
or older must be seated in the front
seat, move the seat as far back as
possible and properly restrain them
in the seat.

[NEVER allow an infant or child to be
carried on an occupant’s lap.

[NEVER ride with the seatback
reclined when the vehicle is moving.

[Do not allow children to share a seat
or seat belt.

[Do not wear the shoulder belt under
your arm or behind your back.

[Never wear a seat belt over fragile
objects. If there is a sudden stop or
impact, the seat belt can damage it.

[Do not use the seat belt if it is
twisted. A twisted seat belt will not
protect you properly in an accident.

[Do not use a seat belt if the webbing
or hardware is damaged.
[Do not latch the seat belt into the
buckles of other seats.

[NEVER unfasten the seat belt
whilst driving. This may cause loss
of vehicle control resulting in an
accident.

[Make sure there is nothing in the
buckle interfering with the seat belt
latch mechanism. This may prevent
the seat belt from fastening securely.

[No modifications or additions
should be made by the user which
will either prevent the seat belt
adjusting devices from operating to
remove slack, or prevent the seat
belt assembly from being adjusted to
remove slack. WARNING
Damaged seat belts and seat belt
assemblies will not operate properly.
Always replace:

[Frayed, contaminated, or damaged
webbing.

[Damaged hardware.

[The entire seat belt assembly after it
has been worn in an accident, even
if damage to webbing or assembly is
not apparent.

3-20
Safety system
Seat belt warning light
Driver’s seat belt
„ Instrument cluster
1GQA2083
As a reminder to the driver, the seat
belt warning light will illuminate for
approximately 6 seconds each time you
turn the ignition switch ON regardless of
belt fastening.
If the seat belt is not fastened when the
ignition switch is turned ON or if it is
disconnected after the ignition switch
is turned ON, the seat belt warning light
will illuminate until the belt is fastened.
If you start to drive without the seat belt
fastened or you unfasten the seat belt
when you drive under 12mph (20km/h),
the corresponding warning light will
continue to illuminate until you fasten
the seat belt.
If you continue to drive without the
seat belt fastened or you unfasten the
seat belt when you drive over 12mph
(20km/h), the seat belt warning chime
will sound for approximately 100
seconds and the corresponding warning
light will blink.
Front passenger’s seat belt
(if equipped)
As a reminder to the front passenger, the
front passenger’s seat belt warning lights
will illuminate for approximately
6 seconds each time you turn the ignition
switch ON regardless of belt fastening.
If the seat belt is not fastened when the
ignition switch is turned ON or if it is
disconnected after the ignition
switch is turned ON, the seat belt warning
light will illuminate until the belt is fastened.
If you start to drive without the seat belt
fastened or you unfasten the seat belt
when you drive under 12mph (20km/h), the
corresponding warning light will continue to
illuminate until you fasten the seat belt.
If you continue to drive without the seat
belt fastened or you unfasten the seat belt
when you drive over 12mph (20km/h),
the seat belt warning chime will sound
for approximately 100 seconds and the
corresponding warning light will blink.
WARNING
Riding in an improper position
adversely affects the front passenger’s
seat belt warning system. It is
important for the driver to instruct the
passenger to properly be seated as
instructed in this manual.
i Information
‡
Although the front passenger seat is not
occupied, the seat belt warning light will
blink or illuminate for 6 seconds. Also,
when the front passenger gets off the
vehicle whilst the warning is activating,
the warning may continue for 6 seconds
even after the passenger gets off.

3-24
Safety system
Rear centre seat belt
(if equipped)
OAC3039044TU
When using the rear centre seat belt, the
buckle with the “CENTER” mark must be
used.
i Information
If you are not able to pull out the safety
belt from the retractor, firmly pull the
belt out and release it. After release, you
will be able to pull the belt out smoothly.
Pre-tensioner seat belt
(if equipped)
OLMB033039/H
[1] : Retractor pre-tensioner seat belt
Your vehicle is equipped with driver’s
and front passenger’s Pre-tensioner
Seat Belts (Retractor Pre-tensioner). The
purpose of the pre-tensioner is to make
sure the seat belts fit tightly against the
occupant’s body in certain frontal or
side collision(s). The pre-tensioner seat
belts may be activated in crashes where
the frontal or side collision(s) is severe
enough, together with the air bags.
When the vehicle stops suddenly, or if
the occupant tries to lean forward too
quickly, the seat belt retractor will lock
into position.
In certain frontal collisions, the pre-
tensioner will activate and pull the seat
belt into tighter contact against the
occupant’s body.
If the system senses excessive tension
on the driver or passenger’s seat
belt when the pre-tensioner system
activates, the load limiter inside the
retractor pre-tensioner will release some
of the pressure on the affected seat belt
(if equipped with load limiter).

3-25
03
CAUTION
The pre-tensioner will activate not only
in a frontal collision but also in a side
collision, if the vehicle is equipped with
a side or curtain air bag.
WARNING

[Always wear your seat belt and sit
properly in your seat.

[Do not use the seat belt if it is loose
or twisted. A loose or twisted seat
belt will not protect you properly in
an accident.

[Do not place anything near the
buckle. This may adversely affect
the buckle and cause it to function
improperly.

[Always replace your pre-tensioners
after activation or an accident.

[NEVER inspect, service, repair or
replace the pre-tensioners yourself.
We recommend that you have the
pre-tensioners inspected, serviced,
repaired or replaced by a HYUNDAI
authorised repairer.

[Do not hit the seat belt assemblies.
WARNING
Do not touch the pre-tensioner seat
belt assemblies for several minutes
after they have been activated. When
the pre-tensioner seat belt mechanism
deploys during a collision, the pre-
tensioner can become hot and can burn
you.
CAUTION
Body work on the front area of
the vehicle may damage the pre-
tensioner seat belt system. Therefore,
we recommend that the system be
serviced by a HYUNDAI authorised
repairer.

3-26
Safety system
8KMB3311/H
The Pre-Tensioner Seat Belt System
consists mainly of the following
components. Their locations are shown
in the illustration above:
(1) SRS air bag warning light
(2) Front retractor pre-tensioner
(if equipped)
(3) SRS control module
OBC3030012R
„Rear
(4) Rear retractor pre-tensioner
(if equipped)
NOTICE
The sensor that activates the SRS
air bag is connected with the pre–
tensioner seat belts. The SRS air bag
warning light on the instrument panel
will illuminate for approximately 6
seconds after the ignition switch is
placed to the ON position, and then it
should turn off.
If the pre-tensioner is not working
properly, the warning light will
illuminate even if the SRS air bag is not
malfunctioning. If the warning light
does not illuminate, stays illuminated
or illuminates when the vehicle is
being driven, we recommend the pre-
tensioner seat belts and/or SRS air bags
be inspected by a HYUNDAI authorised
repairer as soon as possible.

3-27
03
NOTICE

[Pre-tensioner seat belts may be
activated in certain frontal or side
collisions.

[When the pre-tensioner seat belts are
activated, a loud noise may be heard
and fine dust, which may appear
to be smoke, may be visible in the
passenger compartment. These are
normal operating conditions and are
not hazardous.

[Although it is non-toxic, the fine
dust may cause skin irritation and
should not be breathed for prolonged
periods. Wash all exposed skin areas
thoroughly after an accident in which
the pre-tensioner seat belts were
activated.
Additional seat belt safety
precautions
Seat belt use during pregnancy
The seat belt should always be used
during pregnancy. The best way to
protect your unborn child is to protect
yourself by always wearing the seat belt.
Pregnant women should always wear
a lap-shoulder seat belt. Place the
shoulder belt across your chest, routed
between your breasts and away from
your neck. Place the lap belt below your
belly so that it fits SNUGLY across your
hips and pelvic bone, under the rounded
part of the belly.
WARNING
To reduce the risk of serious injury or
death to an unborn child during an
accident, pregnant women should
NEVER place the lap portion of the
seat belt above or over the area of the
abdomen where the unborn child is
located.

3-28
Safety system
Seat belt use and children
Infant and small children
Most countries have Child Restraint
Systems laws which require children
to travel in approved Child Restraint
Systems devices, including booster
seats. The age at which seat belts can be
used instead of Child Restraint Systems
differs among countries, so you should
be aware of the specific requirements
in your country, and where you are
travelling. Infant and Child Restraint
Systems must be properly placed and
installed in a rear seat. For more details,
refer to the “Child Restraint Systems” in
this chapter.
WARNING
ALWAYS properly restrain infants and
small children in a Child Restraint System
appropriate for the child’s height and
weight.
To reduce the risk of serious injury or
death to a child and other passengers,
NEVER hold a child in your lap or arms
when the vehicle is moving. The violent
forces created during an accident will
tear off the child from your arms and
throw the child against the interior of the
vehicle.
Small children are best protected from
injury in an accident when properly
restrained in the rear seat by a Child
Restraint System that meets the
requirements of the Safety Standards of
your country. Before buying any Child
Restraint System, make sure that it has
a label certifying that it meets Safety
Standard of your country. The restraint
must be appropriate for your child’s
height and weight. Check the label
on the Child Restraint System for this
information. Refer to “Child Restraint
Systems” in this chapter.
Larger children
Children under age 13 and who are too
large for a booster seat must always
occupy the rear seat and use the
available lap/shoulder belts. A seat belt
should lie across the upper thighs and
be snug across the shoulder and chest
to restrain the child safely. Check belt fit
periodically. A child’s squirming could
put the belt out of position. Children are
afforded the most safety in the event of
an accident when they are restrained by
a proper restraint system and/or seat
belts in the rear seat.
If a larger child over age 13 must be
seated in the front seat, the child must
be securely restrained by the available
lap/shoulder belt and the seat should be
placed in the rearmost position.
If the shoulder belt portion slightly
touches the child’s neck or face, try
placing the child closer to the centre
of the vehicle. If the shoulder belt still
touches their face or neck, they need to
be returned to an appropriate booster
seat in the rear seat.
WARNING

[Always make sure larger children’s
seat belts are worn and properly
adjusted.

[NEVER allow the shoulder belt to
contact the child’s neck or face.

[Do not allow more than one child to
use a single seat belt.

3-34
Safety system
Suitability of each seating position for belted & ISOFIX Child Restraint Systems (CRS)according to UN
regulations (Information for use by vehicle users and CRS manufacturers)
[Yes : Suitable for fitment of the designated category of CRS

[ No : Not suitable for fitment of the designated category of CRS

[“-” : Not applicable

[The table is based on LHD vehicle. Except for the front passenger seat, the table is valid for RHD vehicle.For RHD vehicle
front passenger seat, please use information for the seating position number 3.
Ye s
Seating positions
123
456
Airbag
ONAirbag
OFF
Universal belted CRS
1)
All mass groups - - NoYes
1)
(F,R)Ye s
(F,R)Yes
2)
F, RYe s
(F,R)
i-size CRSISOFIX CRF :
F2, F2X, R1, R2- - No NoYe s
(F,R)NoYe s
(F,R)
Carry-cot (ISOFIX lateral facing CRS)ISOFIX CRF:
L1, L2- - No No No No No
ISOFIX infant CRS
(i.e. CRS for a baby)ISOFIX CRF :
R1 - - No NoYe s
(R)NoYes
(R)
ISOFIX toddler CRS
- small ISOFIX CRF :
F2,F2X,R2,R2X - - No NoYes
(F,R)NoYes
(F,R)
ISOFIX toddler CRS – large* (* : not booster seats)ISOFIX CRF :
F3,R3 - - No NoYes
(F,R)NoYes
(F,R)
Booster Seat
– reduced WidthISO CRF : B2 - - Yes Yes Yes Yes Yes
Booster Seat
– full WidthISO CRF : B3 - - Yes Yes Yes Yes Yes
F : Forward facing R : Rearward facing
Note
1) : To install Universal CRS to 2nd row seating positions, 1st row seat should be adjust forward properly.
Note 2) : Never install CRS with a support leg on 2nd row centre seating position.

3-35
03
Seat NumberPosition
in the vehicleSeating positions
1 Front left
2 Front centre
3 Front right
42
nd row left
52
nd row centre
62
nd row right
❈ If the vehicle head restraint prevents proper installation of a CRS, the head restraint of the
seating position shall be readjusted or entirely removed
❈ Never place a rearward facing Child Restraint System on the front passenger seat, unless the
air bag is deactivated.
Recommended CRS for Vehicle according to UN regulations
(Information for use by vehicle users and CRS manufacturers)
Mass
groupName Manufacturer Type of FixationECE
Approval Number
Group 2 KidFix III S Britax RömerISOFIX and vehicle belt,
using CRS lap belt guideR44/04 - E1 – 04301304
Group 3 Junior III Graco Vehicle belt R44/04 – E11 – 03.44.165
CRS Manufacturer information
Britax : http://www.britax.com
Graco : http://www.gracobaby.com