FRONT HYUNDAI I20 2023 Repair Manual
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2023, Model line: I20, Model: HYUNDAI I20 2023Pages: 649, PDF Size: 12.35 MB
Page 195 of 649
5-54
Convenient features
OPDE046058
„Front windscreen wiper/washer
„Rear windscreen wiper/washer
OPDE046060
A : Wiper speed control
· MIST (
) – Single wipe
· OFF (O) – Off
· INT (---) – Intermittent wipe
w $ 8 7 2
J $ X W R F R Q W U R O Z L S H
· LO (1) – Low wiper speed
· HI (2) – High wiper speed
B : Intermittent wipe time adjustment
C : Wash with brief wipes (front)
(pull lever towards you)
D : Rear wiper control*
· 2 – High wiper speed
· 1 – Low wiper speed
· O – Off
E : Wash with brief wipes (rear)
(push lever away from you)
L I H T X L S S H G
Windscreen wipers
Operates as follows when the ignition
switch is in the ON position.
MIST (
) : For a single wiping cycle,
push the lever upward and
release. The wipers will
operate continuously if the
lever is held in this position.
OFF (O) : Wiper is not in operation.
INT (---) : Wiper operates intermittently
at the same wiping intervals.
To vary the speed setting, turn
the speed control knob (B).
AUTO : The rain sensor located on the
upper end of the windscreen
glass senses the amount of
rainfall and controls the wiping
cycle for the proper interval.
The more it rains, the faster the
wiper operates. When the rain
stops, the wiper stops. To vary
the speed setting, turn the speed
control knob.
LO (1) : The wiper runs at a lower speed.
HI (2) : The wiper runs at a higher speed.
i Information
, I W K H U H L V K H D Y \ D F F X P X O D W L R Q R I V Q R Z
or ice on the windscreen, defrost the
windscreen for about 10 minutes, or until
the snow and/or ice is removed before
using the windscreen wipers to ensure
proper operation.
, I \ R X G R Q R W U H P R Y H W K H V Q R Z D Q G R U L F H
before using the wiper and washer, it may
damage the wiper and washer system.
: , 3 ( 5 6 $ 1 ' : $ 6 + ( 5 6
Page 197 of 649
5-56
Convenient features
CAUTION
[ To prevent possible damage to the
washer pump, do not operate the
washer when the fluid reservoir is
empty.
[ To prevent possible damage to the
wipers or windscreen, do not operate
the wipers when the windscreen is
dry.
[ To prevent damage to the wiper
arms and other components, do
not attempt to move the wipers
manually.
[ To prevent possible damage to the
wipers and washer system, use anti-
freezing washer fluids in the winter
season or cold weather.
Rear window wiper and washer
switch (if equipped)
OTLE045167
The rear window wiper and washer
switch is located at the end of the wiper
and washer switch lever.
Turn the switch to desired position to
operate the rear wiper and washer.
· 2 – High wiper speed
· 1 – Low wiper speed
· O – Off
OTLE045167
Push the lever away from you to spray
rear washer fluid and to run the rear
wipers 1~3 cycles. The spray and wiper
operation will continue until you release
the lever. (if equipped)
Auto rear wiper (if equipped)
The rear wiper will operate whilst the
vehicle is in reverse with the front wiper
ON by selecting the function on the LCD
display.
* R W R S 8 V H U 6 H W W L Q J V
Page 203 of 649
5-62
Convenient features
System operation
Ventilation
1. Select the Face Level mode.
2. Set the air intake control to fresh
mode.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
Heating
1. Select the Floor Level mode.
2. Set the air intake control to fresh
mode.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
5. If desired, turn the air conditioning ON
with the temperature control knob set
to heat in order to dehumidify the air
before it enters into the cabin.
If the windscreen fogs up, select the
Floor & Defrost
mode or press the
Front Defrost mode.
2 S H U D W L R Q 7 L S V
[ 7 R N H H S G X V W R U X Q S O H D V D Q W I X P H V
from entering the vehicle through the
ventilation system, temporarily set the
air intake control to the recirculation
mode. Be sure to return the control
to fresh mode position when the
irritation has passed to keep fresh air
in the vehicle. This will help keep the
driver alert and comfortable.
[ 7 R S U H Y H Q W L Q W H U L R U I R J R Q W K H
windscreen, set the air intake control
to fresh mode and fan speed to
the desired position, turn on the
air conditioning system, and adjust
the temperature control to desired
temperature.
Air conditioning
HYUNDAI Air Conditioning Systems are
filled with R-134a or R1234yf refrigerant.
1. Start the engine.
2. Push the air conditioning button.
3. Select the Face Level
mode.
4. Set the air intake control to
Recirculation mode temporarily to
allow the cabin to cool quickly. When
the desired temperature in the cabin
is reached, change the air intake
control back to Fresh mode.
5. Adjust the fan speed control and
temperature control to maintain
maximum comfort.
i Information
OBC3050052
< R X U Y H K L F O H L V I L O O H G Z L W K 5 D R U
5 \ I D F F R U G L Q J W R W K H U H J X O D W L R Q L Q
your country at the time of production.
< R X F D Q I L Q G R X W Z K L F K D L U F R Q G L W L R Q L Q J
refrigerant is applied to your vehicle on
the label located inside of the bonnet.
Page 208 of 649
5-67
05
Automatic heating and air
conditioning
OBC3050110R
1. Press the AUTO button.
The modes, fan speeds, air intake and
air-conditioning will be controlled
automatically according to the
temperature setting you select.
OBC3050111R
2. Push the temperature control switch
to set the desired temperature. If
the temperature is set to the lowest
setting (Lo), the air conditioning
system will operate continuously.
[ 7 R W X U Q W K H D X W R P D W L F R S H U D W L R Q R I I
select any button of the following:
- Mode selection button
- Front windscreen defroster button
(Press the button one more time
to deselect the front windscreen
G H I U R V W H U I X Q F W L R Q 7 K H S $ 8 7 2T V L J Q
will illuminate on the information
screen once again.) - Fan speed control toggle switch
The selected function will be
controlled manually whilst other
functions operate automatically.
[ ) R U \ R X U F R Q Y H Q L H Q F H X V H W K H $ 8 7 2
button and set the temperature to
22°C (72°F).
OAI3059112I
i Information
1 H Y H U S O D F H D Q \ W K L Q J Q H D U W K H V H Q V R U W R
ensure better control of the heating and
cooling system.
Page 213 of 649
5-72
Convenient features
Air conditioning
OBC3050116R
Push the A/C button to manually turn
the air conditioning system on (indicator
light will illuminate).
Push the button again to turn the air
conditioning system off.
OFF mode
OBC3050117R
Push the OFF button of the front to turn
off the climate control system.
You can still operate the air intake
buttons as long as the ignition switch is
in the ON position.
However, the air climate control system
turns on when you push the mode
selection buttons.
System operation
Ventilation
1. Select the Face Level mode.
2. Set the air intake control to fresh
mode.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
Heating
1. Select the Floor Level mode.
2. Set the air intake control to fresh
mode.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
5. If desired, turn the air conditioning ON
with the temperature control knob set
to heat in order to dehumidify the air
before it enters into the cabin.
If the windscreen fogs up, select the
Floor & Defrost
mode or press the
Front Defrost mode.
Page 214 of 649
5-73
05
2 S H U D W L R Q 7 L S V
[ 7 R N H H S G X V W R U X Q S O H D V D Q W I X P H V
from entering the vehicle through the
ventilation system, temporarily set the
air intake control to the recirculation
mode. Be sure to return the control
to fresh mode position when the
irritation has passed to keep fresh air
in the vehicle. This will help keep the
driver alert and comfortable.
[ 7 R S U H Y H Q W L Q W H U L R U I R J R Q W K H
windscreen, set the air intake control
to fresh mode and fan speed to
the desired position, turn on the
air conditioning system, and adjust
the temperature control to desired
temperature.
Air conditioning
HYUNDAI Air Conditioning Systems are
filled with R-134a or R-1234yf refrigerant.
1. Start the engine.
2. Push the air conditioning button.
3. Select the Face Level
mode.
4. Set the air intake control to
Recirculation mode temporarily to
allow the cabin to cool quickly. When
the desired temperature in the cabin is
reached, change the air intake control
back to Fresh mode.
5. Adjust the fan speed control and
temperature control to maintain
maximum comfort.
i Information
OBC3050052
< R X U Y H K L F O H L V I L O O H G Z L W K 5 D
according to the regulation in your
F R X Q W U \ D W W K H W L P H R I S U R G X F W L R Q < R X
can find out which air conditioning
refrigerant is applied to your vehicle on
the label located in front of the engine
compartment.
Page 221 of 649
5-80
Convenient features
7 R F D Q F H O R U U H V H W W K H $ X W R ' H I R J J L Q J
System
Press the front windscreen defroster
button for 3 seconds when the ignition
switch is in the ON position.
When the Auto Defogging System is
cancelled, defrost button indicator will
blink 3 times.
When the Auto Defogging System is
reset, defrost button indicator will blink
6 times without a signal.
i Information
: K H Q W K H D L U F R Q G L W L R Q L Q J L V W X U Q H G R Q E \
Auto defogging system, if you try to turn
off the air conditioning, the indicator will
blink 3 times and the air conditioning will
not be turned off.
7 R P D L Q W D L Q W K H H I I H F W L Y H Q H V V D Q G
H I I L F L H Q F \ R I W K H $ X W R ' H I R J J L Q J 6 \ V W H P
G R Q R W V H O H F W 5 H F L U F X O D W L R Q P R G H Z K L O V W
the system is operating.
: K H Q W K H $ X W R ' H I R J J L Q J 6 \ V W H P L V
operating, the blower speed adjustment
knob, the temperature adjustment knob,
and the air intake control button are all
disabled.
NOTICE
Do not remove the sensor cover
located at the top of the driver side
windscreen glass.
Damage to system parts could occur
and may not be covered by your vehicle
warranty.
Defroster
NOTICE
To prevent damage to the conductors
bonded to the inside surface of the rear
window, never use sharp instruments
or window cleaners containing
abrasives to clean the window.
i Information
, I \ R X Z D Q W W R G H I U R V W D Q G G H I R J W K H
I U R Q W Z L Q G V F U H H Q U H I H U W R
Page 226 of 649
5-85
05
NOTICE
[ . H H S \ R X U G U L Q N V V H D O H G Z K L O V W
driving to prevent spilling your drink.
If liquid spills, it may get into the
vehicle’s electrical/electronic system
and damage electrical/electronic
parts.
[ : K H Q F O H D Q L Q J V S L O O H G O L T X L G V G R
not dry the cup holder using hot
temperatures. This may damage the
cup holder.
Sliding armrest (if equipped)
OBC3050035
To move the armrest forward:
Grab the front portion of armrest (1) then
pull it forward.
To move the armrest rearward:
Grab the front portion of armrest (1) then
push it rearward.
Sunvisor
OAE046425R
To use a sunvisor, pull it downward.
To use a sunvisor for a side window, pull
it downward, unsnap it from the bracket
(1) and swing it to the side (2).
To use the vanity mirror, pull down the
sunvisor and slide the mirror cover (3).
Use the ticket holder (4) to hold tickets.
i Information
Close the vanity mirror cover securely
and return the sunvisor to its original
position after use.
WARNING
) R U \ R X U V D I H W \ G R Q R W E O R F N \ R X U Y L H Z
when using the sunvisor.
NOTICE
Do not put several tickets in the ticket
holder at one time. This could cause
damage to the ticket holder.
Page 228 of 649
5-87
05
USB charger (if equipped)
OBC3N051027AU
The USB charger is located inside the
F R Q V R O H E R [ E H W Z H H Q W K H G U L Y H UT V V H D W
D Q G W K H I U R Q W S D V V H Q J H UT V V H D W , Q V H U W
the USB charger into the USB port, and
re-charge a smart phone or a tablet PC.
[ $ F K D U J L Q J V W D W X V F K D U J L Q J F R P S O H W L R Q
message is displayed on a screen of a
smart phone or a tablet PC.
[ $ V P D U W S K R Q H R U D W D E O H W 3 & P D \
get warmer during the re-charging
process. It does not indicate any
malfunction with the charging system.
[ $ V P D U W S K R Q H R U D W D E O H W 3 & Z K L F K
adopts a different re-charging
method, may not be properly
re-charged. In this case, use an
exclusive charger of your device.
[ 7 K H F K D U J L Q J W H U P L Q D O L V R Q O \ W R
re-charge a device. Do not use the
charging terminal either to turn ON an
audio or to play media on the AVN.
Wireless mobile phone charging
system (if equipped)
OBC3N050028
[A] : Charging pad
There is a wireless mobile phone charger
inside the front console.
The system is available when all doors
are closed, and when the ignition switch
is in the ON position.
Page 229 of 649
5-88
Convenient features
To charge a mobile phone
The wireless mobile phone charging
system charges only the Qi-enabled
mobile phones (
). Read the label on
the mobile phone accessory cover or
Y L V L W \ R X U P R E L O H S K R Q H P D Q X I D F W X U H UT V
website to check whether your mobile
phone supports the Qi technology.
The wireless charging process starts
when you put a Qi-enabled mobile
phone on the wireless charging unit.
1. Remove other items, including the
smart key, from the wireless charging
unit. If not, the wireless charging
process may be interrupted. Place
the mobile phone on the centre of
charging pad.
2. The indicator light is orange when
the mobile phone is charging. The
indicator light turns green when phone
charging is complete.
3. You can turn ON or OFF the wireless
charging function in the User Settings
mode on the instrument cluster. For
further information, refer to the “LCD
Display Modes” in this chapter 4.
If your mobile phone is not charging:
- Slightly change the position of the
mobile phone on the charging pad.
- Make sure the indicator light is orange.
The indicator light will blink orange for
10 seconds if there is a malfunction in
the wireless charging system.
In this case, temporarily stop the
charging process, and re-attempt to
wirelessly charge your mobile phone.
The system warns you with a message
on the LCD display if the mobile phone
is still on the wireless charging unit after
the engine is turned OFF and the front
door is opened.
) R U V R P H P D Q X I D F W X U H U VT P R E L O H S K R Q H V
the system may not warn you even
though the mobile phone is left on the
wireless charging unit. This is due to the
particular characteristic of the mobile
phone and not a malfunction of the
wireless charging.