LED HYUNDAI I20 2023 Owner's Guide

5-31
05
If your vehicle is equipped with a
sunroof, you can slide or tilt your sunroof
with the sunroof switch located on the
overhead console.
OBC3050020
The sunroof can only be operated when
the ignition switch is in the ON position.
The sunroof can be operated for
approximately 3 minutes after the
Engine Start/Stop button is in the ACC or
OFF position. However, if the front door
is open, the sunroof cannot be operated
even within the 3 minutes period.
WARNING

[Never adjust the sunroof or sunshade
whilst driving. This could result
in loss of control and an accident
that may cause injury, or property
damage.

[Do not leave the engine running
and the key in your vehicle with
unsupervised children. Unattended
children could operate the sunroof,
which could result in serious injury.

[Do not sit on the top of the vehicle. It
may cause injury or vehicle damage.
NOTICE
Do not operate the sunroof when the
roof bars are installed on the vehicle or
when there is luggage on the roof.
Sunshade
OBC3050021
Use the power sunshade to block direct
sunlight coming through the sunroof
glass.
Open or close the sunshade by hand.
i Information
7KHVXQVKDGHZLOORSHQDXWRPDWLFDOO\
when the sunroof glass moves, but the
sunshade does not close automatically
when the sunroof glass is closed. Also,
only the sunshade cannot be closed when
the sunroof glass is opened.
NOTICE
Do not pull the sunshade up or down,
or apply excessive force as such action
may damage the sunshade or cause it
to malfunction.
681522)

5-37
05
Closing the bonnet
1. Before closing the bonnet, check the
following:

[$OOILOOHUFDSVLQHQJLQHFRPSDUWPHQW
must be correctly installed.

[*ORYHVUDJVRUDQ\RWKHU
combustible materials must
be removed from the engine
compartment.
2. Return the support rod to its clip
location for preventing it from rattling.
3. Lower the bonnet halfway (lifted
approximately 30cm from the closed
position) and push down to securely
lock in place. Then double check to be
sure the bonnet is secure.
If the bonnet can be raised slightly, it
is not securely locked. Open it again
and close it with more force.
WARNING

[Before closing the bonnet, ensure
all obstructions are removed from
around the bonnet opening.

[Always double check to be sure
that the bonnet is firmly latched
before driving away. Check there
is no bonnet open warning light or
message displayed on the instrument
cluster. Driving with the bonnet
opened may cause a total loss of
visibility, which might result in an
accident.

[Do not move the vehicle with the
bonnet in the raised position, as
vision is obstructed, which might
result in an accident, and the bonnet
could fall or be damaged.
Tailgate
Opening the tailgate
OBC3050025

[ 7KHWDLOJDWHLVORFNHGRUXQORFNHG
when all doors are locked or unlocked
with the remote key, smart key or
central door lock/unlock switch.

[ ,IXQORFNHGWKHWDLOJDWHFDQEH
opened by pulling up the tailgate
outside handle.
i Information
,QFROGDQGZHWFOLPDWHVGRRUORFNDQG
door mechanisms may not work properly
GXHWRIUHH]LQJFRQGLWLRQV
WARNING
The tailgate swings upward. Make
sure no objects or people are near the
rear of the vehicle when opening the
tailgate.

5-41
05

[Do not get back into a vehicle
once you have begun refuelling.
You can generate a build-up of
static electricity by touching,
rubbing or sliding against any item
or fabric capable of producing
static electricity. Static electricity
discharge can ignite fuel vapours
causing a fire. If you must re-enter
the vehicle, you should once again
eliminate potentially dangerous
static electricity discharge by
touching a metal part of the vehicle,
away from the fuel filler neck, nozzle
or other petrol source, with your bare
hand.

[When refuelling, always move the
shift lever to the N (Neutral, for
Automatic transmission/Dual clutch
transmission) or the first gear or R
(Reverse, for Manual transmission)
position, set the parking brake,
and place the ignition switch to the
/2&.2))SRVLWLRQ6SDUNVSURGXFHG
by electrical components related to
the engine can ignite fuel vapours
causing a fire.

[When using an approved portable
fuel container, be sure to place
the container on the ground prior
to refuelling. Static electricity
discharge from the container can
ignite fuel vapours causing a fire.
Once refuelling has begun, contact
between your bare hand and the
vehicle should be maintained until
the filling is complete.

[Use only approved portable plastic
fuel containers designed to carry and
store petrol.
[Do not use matches or a lighter and
do not smoke or leave a lit cigarette
in your vehicle whilst at a gas station,
especially during refuelling.

[Do not over-fill or top-off your
vehicle tank, which can cause petrol
spillage.

[If a fire breaks out during refuelling,
leave the vicinity of the vehicle, and
immediately contact the manager
of the gas station and then contact
WKHORFDOILUHGHSDUWPHQW)ROORZDQ\
safety instructions they provide.

[If pressurized fuel sprays out, it can
cover your clothes or skin and thus
subject you to the risk of fire and
burns. Always remove the fuel cap
carefully and slowly. If the cap is
venting fuel or if you hear a hissing
sound, wait until the condition stops
before completely removing the cap.

[Always check that the fuel cap is
installed securely to prevent fuel
spillage in the event of an accident.
i Information
0DNHVXUHWRUHIXHO\RXUYHKLFOH
DFFRUGLQJWRWKH

5-50
Convenient features
- If the light switch is pushed away
when High Beam Assist is operating,
High Beam Assist will turn off.
- If the light switch is pulled towards
you when the high beam is off, the
high beam will turn on. When you let
go of the light switch, the lever will
move to the middle and the high beam
will turn off.
- If the light switch is pulled towards
you when the high beam is on by High
Beam Assist, and High Beam Assist
will turn off.
- If the light switch is placed to the
headlight position (
), High Beam
Assist will turn off and the low beam
will be on continuously.
When High Beam Assist is operating, the
high beam switches to low beam in the
following conditions.
- When the headlight of an on-coming
vehicle is detected.
- When the tail light of a vehicle in front
is detected.
- When the headlight or tail light of a
motorcycle or a bicycle is detected.
- When the surrounding ambient light is
bright enough that high beams are not
required.
- When streetlights or other lights are
detected.
- When the light switch is not in the
AUTO position.
- When High Beam Assist is off.
- When the vehicle speed is below 19
mph (30 km/h).
System malfunction and
limitations
System malfunction
OTM050218L
When High Beam Assist is not working
properly, the warning message will come
on for a few seconds. After the message
disappears, the master warning light
(
) will illuminate.
We recommend that you take your
vehicle to a HYUNDAI authorised
repairer and have the system checked.
CAUTION
The system may not operate normally if
any of the following conditions should
occur:
1. When the illumination from an
on-coming vehicle or a vehicle in
front is dim. Such examples may
include:

[When the headlights of an oncoming
vehicle or the tail lights of a vehicle
in front is covered with dust, snow,
or water

[When the headlights on an
RQFRPLQJYHKLFOHDUH2))EXWWKH
fog lights are ON)

5-55
05
AUTO (Automatic) control
(if equipped)
The rain sensor located at the top of the
windscreen glass senses the amount of
rainfall and controls the wiping cycle for
the proper interval. The wiper operation
time will be automatically controlled,
depending on rainfall.
When the rain stops, the wiper stops. To
vary the speed setting, turn the speed
control knob.
If the wiper switch is set in AUTO mode
when the ignition switch is in the ON
position, the wiper will operate once to
perform a self-check of the system. Set
the wiper to the OFF position when the
wiper is not in use.
WARNING
To avoid personal injury from the
windscreen wipers, when the engine
is running and the windscreen wiper
switch is placed in the AUTO mode:
Do not touch the upper end of the
windscreen glass facing the rain sensor.
Do not wipe the top of the windscreen
glass with a damp or wet cloth.
Do not put pressure on the windscreen
glass.
NOTICE
When washing the vehicle, set the
ZLSHUVZLWFKLQWKH2))SRVLWLRQWRVWRS
the auto wiper operation. The wiper
may operate and be damaged if the
switch is set in the AUTO mode whilst
washing the vehicle.
Do not remove the sensor cover
located at the top of the passenger side
windscreen glass. Damage to system
parts could occur and may not be
covered by your vehicle warranty.
Windscreen washers
OTLE045168
In the OFF (O) position, pull the lever
gently toward you to spray washer
fluid on the windscreen and to run the
wipers 1-3 cycles. The spray and wiper
operation will continue until you release
the lever. If the washer does not work,
you may need to add washer fluid to the
washer fluid reservoir.
WARNING
When the outside temperature is
below freezing, ALWAYS warm the
windscreen using the defroster to
prevent the washer fluid from freezing
on the windscreen and obscuring your
vision which could result in an accident
and serious injury or death.

5-59
05
OBC3050103
The mode selection knob controls the
direction of the air flow through the
ventilation system.
Air can be directed to the floor,
dashboard outlets, or windscreen. Five
symbols are used to represent Face,
Bi-Level, Floor, Floor-Defrost and
Defrost air position.
)DFH/HYHO%'
Air flow is directed toward the upper
body and face. Additionally, each outlet
can be controlled to direct the air
discharged from the outlet.
%L/HYHO%&'
Air flow is directed towards the face and
the floor.
)ORRU/HYHO$&'
Most of the air flow is directed to the
floor, with a small amount of the air
being directed to the windscreen, side
window defrosters and side vents.
)ORRU'HIURVW/HYHO
$&'
Most of the air flow is directed to the
floor and the windscreen with a small
amount directed to the side window
defrosters and side vents.
'HIURVW/HYHO$'
Most of the air flow is directed to the
windscreen with a small amount of air
directed to the side vents.

5-60
Convenient features
OBC3N051101AU
,QVWUXPHQWSDQHOYHQWV
The instrument panel vent air flow can
be directed up/down or left/right using
the vent adjustment lever.
To close the vent adjustment lever,
rotate it to the outer side till the end. To
open the vent, rotate it to the inner side.
Temperature control
OBC3050104
The temperature will increase by turning
the knob to the right.
The temperature will decrease by
turning the knob to the left.
Air intake control
OBC3050105
aThe air intake control button is used to
select either Fresh mode (outside air) or
Recirculation mode (cabin air).
5HFLUFXODWLRQPRGH
When Recirculation mode
is selected, air from the
passenger compartment
will be recirculated
through the system and
heated or cooled
according to the function
selected.
)UHVKPRGH
When Fresh mode is
selected, air enters the
vehicle from outside and is
heated or cooled
according to the function
selected.

5-62
Convenient features
System operation
Ventilation
1. Select the Face Level mode.
2. Set the air intake control to fresh
mode.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
Heating
1. Select the Floor Level mode.
2. Set the air intake control to fresh
mode.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
5. If desired, turn the air conditioning ON
with the temperature control knob set
to heat in order to dehumidify the air
before it enters into the cabin.
If the windscreen fogs up, select the
Floor & Defrost
mode or press the
Front Defrost mode.
2SHUDWLRQ7LSV

[ 7RNHHSGXVWRUXQSOHDVDQWIXPHV
from entering the vehicle through the
ventilation system, temporarily set the
air intake control to the recirculation
mode. Be sure to return the control
to fresh mode position when the
irritation has passed to keep fresh air
in the vehicle. This will help keep the
driver alert and comfortable.

[ 7RSUHYHQWLQWHULRUIRJRQWKH
windscreen, set the air intake control
to fresh mode and fan speed to
the desired position, turn on the
air conditioning system, and adjust
the temperature control to desired
temperature.
Air conditioning
HYUNDAI Air Conditioning Systems are
filled with R-134a or R1234yf refrigerant.
1. Start the engine.
2. Push the air conditioning button.
3. Select the Face Level
mode.
4. Set the air intake control to
Recirculation mode temporarily to
allow the cabin to cool quickly. When
the desired temperature in the cabin
is reached, change the air intake
control back to Fresh mode.
5. Adjust the fan speed control and
temperature control to maintain
maximum comfort.
i Information
OBC3050052
<RXUYHKLFOHLVILOOHGZLWK5DRU
5\IDFFRUGLQJWRWKHUHJXODWLRQLQ
your country at the time of production.
<RXFDQILQGRXWZKLFKDLUFRQGLWLRQLQJ
refrigerant is applied to your vehicle on
the label located inside of the bonnet.

5-63
05
NOTICE

[ 7KHUHIULJHUDQWV\VWHPVKRXOGRQO\
be serviced by trained and certified
technicians to insure proper and safe
operation.

[ 7KHUHIULJHUDQWV\VWHPVKRXOGEH
serviced in a well-ventilated place.

[ 7KHDLUFRQGLWLRQLQJHYDSRUDWRU
(cooling coil) shall never be repaired
or replaced with one removed from
a used or salvaged vehicle and new
replacement MAC evaporators shall
be certified (and labelled) as meeting
SAE Standard J2842.
i Information

5-64
Convenient features
System maintenance
Climate control air filter
OIK047401L
[A] : Outside air, [B] : Recirculated air
[C] : Climate control air filter, [D] : Blower
[E] : Evaporator core, [F] : Heater core
This filter is installed behind the glove
box. It filters the dust or other pollutants
that enter the vehicle through the
heating and air conditioning system.
We recommend that the climate control
air filter be replaced by a HYUNDAI
authorised repairer according to the
maintenance schedule. If the vehicle is
being driven in severe conditions such
as dusty or rough roads, more frequent
climate control filter inspections and
changes are required.
If the air flow rate suddenly decreases,
we recommend the system be checked
at a HYUNDAI authorised repairer.
i Information