LED HYUNDAI I20 2023 Owners Manual
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2023, Model line: I20, Model: HYUNDAI I20 2023Pages: 649, PDF Size: 12.35 MB
Page 600 of 649
9-41
09
7 H P S H U D W X U H $ % &
The temperature grades are A (the
highest), B and C representing the tyre’s
resistance to the generation of heat
and its ability to dissipate heat when
tested under controlled conditions on a
specified indoor laboratory test wheel.
Sustained high temperature can cause
the material of the tyre to degenerate
and reduce tyre life, and excessive
temperature can lead to sudden tyre
failure. Grades B and A represent higher
levels of performance on the laboratory
test wheel than the minimum required
by law.
WARNING
The temperature grade for this tyre is
established for a tyre that is properly
inflated and not overloaded. Excessive
speed, under-inflation, over-inflation,
or excessive loading, either separately
or in combination, can cause heat
build-up and possible sudden tyre
failure. This may cause loss of vehicle
control resulting in an accident.
Low aspect ratio tyres
Low aspect ratio tyres, the aspect ratio
is lower than 50, are provided for sporty
looks.
Because low aspect ratio tyres are
optimized for handling and braking, their
sidewall is a little stiffer than a standard
tyre. Also, low aspect ratio tyres tend to
be wider so that they consequently have
a greater contact patch with the road
surface. In some instances, they may
generate more road noise compared
with standard tyres.
CAUTION
% H F D X V H W K H V L G H Z D O O R I D O R Z D V S H F W
ratio tyre is shorter than a standard
tyre, the rim of the wheel and the
tyre itself are more easily more easily
susceptible to damage. Use caution
when driving and follow the guidelines
below to help minimise damage to the
wheel and tyre:
[ : K H Q G U L Y L Q J R Q D U R X J K U R D G R U
driving off a road, be careful not to
damage the tyres and wheels. After
driving, inspect the tyres and wheels.
[ : K H Q S D V V L Q J R Y H U D S R W K R O H V S H H G
bump, manhole, or kerb stone,
drive the vehicle slowly so as not to
damage the tyres and wheels.
[ , I W K H W \ U H L V V X E M H F W H G W R D V H Y H U H
impact, we recommend you have
the tyre and wheel inspected by a
HYUNDAI authorised repairer.
[ , Q V S H F W W K H W \ U H F R Q G L W L R Q D Q G
pressure every 3,000 km (1,800 miles)
to prevent tyre damage.
[ , W L V Q R W H D V \ W R U H F R J Q L V H W \ U H
G D P D J H Z L W K \ R X U R Z Q H \ H V % X W
if there is the slightest hint of tyre
damage, have the tyre checked or
replaced because the tyre damage
may cause air leakage from the tyre.
[ , I W K H W \ U H L V G D P D J H G E \ G U L Y L Q J
on a rough road, off road, pothole,
manhole, or kerb stone, it will not be
covered by the warranty.
Page 620 of 649
9-61
09
OLMB073042L
WARNING
[ Handle halogen bulbs with care.
Halogen bulbs contain pressurized
gas that will produce flying pieces
of glass that could cause injuries if
broken.
[ Wear eye protection when changing
a bulb. Allow the bulb to cool down
before handling it.
[ Always handle them carefully, and
avoid scratches and abrasions. If
the bulbs are lit, avoid contact with
liquids.
[ Never touch the glass with bare
hands. Residual oil may cause the bulb
to overheat and burst when lit.
[ A bulb should be operated only when
installed in a headlight.
[ If a bulb becomes damaged or
cracked, replace it immediately and
carefully dispose of it.
i Information
: H U H F R P P H Q G W K D W W K H K H D G O L J K W D L P L Q J
E H D G M X V W H G D I W H U D Q D F F L G H Q W R U D I W H U W K H
K H D G O L J K W D V V H P E O \ L V U H L Q V W D O O H G
❈ 7 U D I I L F & K D Q J H ) R U ( X U R S H
The low beam light distribution is
asymmetric. If you go abroad to a
country with opposite traffic direction,
this asymmetric part will dazzle
oncoming car driver. To prevent dazzle,
ECE regulation demands several
technical solutions (ex. automatic
change system, adhesive sheet, down
aiming). This headlamps are designed
not to dazzle opposite drivers.
So, you need not change your
headlamps in a country with the
opposite traffic direction.
Page 622 of 649
9-63
09
OBC3090039
OBC3TN091006
„CUV
7 X U Q V L J Q D O O L J K W
1. Open the bonnet.
2. Remove the turn signal light or low
beam assist-static light bulb cover by
turning it counterclockwise.
3. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
4. Insert a new bulb by inserting it into
the socket and rotating it until it locks
into place.
5. Install the socket in the assembly by
aligning the tabs on the socket with
the slots in the assembly.
Push the socket into the assembly and
turn the socket clockwise.
6. Install the turn signal light or low
beam assist-static light bulb cover by
turning it clockwise.
3 R V L W L R Q O L J K W ' D \ W L P H U X Q Q L Q J O L J K W
L I H T X L S S H G
If the LED lamp does not operate,
we recommend that the system be
inspected by a HYUNDAI authorised
repairer.
The LED lamps cannot be replaced as
a single unit because it is an integrated
unit. The LED lamp has to be replaced
with the unit. Unless a skilled technician
checks or repairs the LED lamp, it may
damage related parts of the vehicle.
Page 623 of 649
9-64
Maintenance
Type D (LED)
OBC3090037
Type E (LED)-N line
OBC3TN091001
(1) headlight (Low)
(2) headlight (High)
(3) Static Bending Light
(4) Turn signal light
(5) Daytime running light & Position light
(6) Front fog light
Type F (LED)-CUV
OBC3V091005
(1) Headlight (Low)
(2) Headlight (High)
(3) Static Bending Light
(4) Daytime running light & Position &
Turn signal light
+ H D G O L J K W 3 R V L W L R Q O L J K W 7 X U Q V L J Q D O
O L J K W ' D \ W L P H U X Q Q L Q J O L J K W / R Z
E H D P D V V L V W V W D W L F O L J K W E X O E U H S O D F H
P H Q W
If the LED lamp does not operate,
we recommend that the system be
inspected by a HYUNDAI authorised
repairer. The LED lamps cannot be
replaced as a single unit because it is an
integrated unit. The LED lamp has to be
replaced with the unit.
Unless a skilled technician checks or
repairs the LED lamp, it may damage
related parts of the vehicle.
Page 626 of 649
9-67
09
Aiming point
OBC3090043
H1 : Lighting centre Ground clearance of Headlight Low & High BeamH3 : Lighting centre Ground clearance of Front fog lightW1 : Lighting centre Distance between Headlight Low & High BeamW3 : Lighting centre Distance between Front fog light
1. Headlamp (LOW - H1, W1 / HIGH BEAM - H2, W2) mm(in.)
Vehicle condition “H1” “H2” “W1” “W2”
Without driver (HAL 2 MFR) 654.9 (25.8) 654.9 (25.8) 1320 (52.0) 1320 (52.0)
Without driver (LED 4 MFR) 670.4 (26.4) 622.3 (24.5) 1396.8 (55.0) 1233.6 (48.57)
With driver (HAL 2 MFR) 646.9 (25.5) 646.9 (25.5) 1320 (52.0) 1320 (52.0)
With driver (LED 4 MFR) 662.4 (26.1) 614.3 (24.2) 1396.8 (55.0) 1233.6 (48.57)
2. Fog lamp (H3, W3)
Vehicle condition “H3” “W3”
Without driver 352 (13.9) 1434.4 (56.5)
With driver 344 (13.6) 1434.4 (56.5)
Page 629 of 649
9-70
Maintenance
Side repeater light replacement
Type A
OBC3090044
If the LED lamp does not operate, we
recommend you to have the vehicle
checked by a HYUNDAI authorised
repairer.
Type B
OAC3089047TU
1. Remove the lamp assembly from the
vehicle by prying the lens and pulling
the assembly out.
2. Disconnect the bulb electrical
connector.
3. Separate the socket and the
lens parts by turning the socket
counterclockwise until the tabs on the
socket align with the slots on the lens
part.
4. Remove the bulb by pulling it straight
out.
5. Insert a new bulb in the socket.
6. Reassemble the socket and the lens
part.
7. Connect the bulb electrical connector.
8. Reinstall the lamp assembly to the
body of the vehicle.
Page 633 of 649
![HYUNDAI I20 2023 Owners Manual 9-74
Maintenance
OBC3090048
[1] : Turn Signal Light,
7 X U Q V L J Q D O O L J K W
4. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the](/img/35/56129/w960_56129-632.png "HYUNDAI I20 2023 Owners Manual 9-74
Maintenance
OBC3090048
[1] : Turn Signal Light,
7 X U Q V L J Q D O O L J K W
4. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the")
9-74
Maintenance
OBC3090048
[1] : Turn Signal Light,
7 X U Q V L J Q D O O L J K W
4. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
5. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
6. Insert a new bulb by inserting it into
the socket and rotating it until it locks
into place.
7. Install the socket in the assembly by
aligning the tabs on the socket with
the slots in the assembly. Push the
socket into the assembly and turn the
socket clockwise.
8. Reinstall the light assembly to the
body of the vehicle.
7 D L O O L J K W 6 W R S O L J K W
If the LED lamp does not operate,
we recommend that the system be
inspected by a HYUNDAI authorised
repairer. The LED lamps cannot be
replaced as a single unit because it is an
integrated unit. The LED lamp has to be
replaced with the unit.
Unless a skilled technician checks or
repairs the LED lamp, it may damage
related parts of the vehicle.
OBC3090050
[1] : Rear Fog Light, [2] : Back-up Light
5 H D U I R J O L J K W
1. Remove the rear tyre and wheel cover.
2. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
3. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
4. Insert a new bulb in the socket.
5. Reinstall the light assembly to the
body of the vehicle.
% D F N X S O L J K W
1. Open the tailgate and remove the
tailgate trim.
2. Loosen the retaining screw of the
tailgate lid cover and then remove the
cover.
3. Disconnect the connector and then
remove the nuts by turning the nuts
counter clockwise.
4. Take the light assembly out.
Page 636 of 649
9-77
09
Type D
OBC3V091006
(1) Turn signal lamp
(2) Tail/Stop light
(3) Rear fog light/Rear reflection light
7 X U Q V L J Q D O O D P S 7 D L O O L J K W 6 W R S
O L J K W
If the LED lamp does not operate,
we recommend that the system be
inspected by a HYUNDAI authorised
repairer. The LED lamps cannot be
replaced as a single unit because it is an
integrated unit.
The LED lamp has to be replaced with
the unit. Unless a skilled technician
checks or repairs the LED lamp, it may
damage related parts of the vehicle.
OBC3V091004
[1] : Rear Fog Light
5 H D U I R J O L J K W 5 H D U U H I O H F W L R Q O L J K W
1. Remove the rear tyre and wheel cover.
2. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
3. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
4. Insert a new bulb in the socket.
5. Reinstall the light assembly to the
body of the vehicle.
Page 647 of 649
9-88
Maintenance
The emission control system of your
vehicle is covered by a written limited
warranty. Please see the warranty
information contained in the Service
Passport in your vehicle.
Your vehicle is equipped with an
emission control system to meet all
emission regulations.
There are three emission control systems
which are as follows.
(1) Crankcase emission control system
(2) Evaporative emission control system
(3) Exhaust emission control system
In order to ensure the proper function
of the emission control systems, it is
recommended that you have your car
inspected and maintained by a HYUNDAI
authorised repairer in accordance
with the maintenance schedule in this
manual.
NOTICE
For the Inspection and Maintenance
Test (with Electronic Stability Control
(ESC) system)
[ 7 R S U H Y H Q W W K H Y H K L F O H I U R P P L V I L U L Q J
during dynamometer testing, turn
the Electronic Stability Control
(ESC) system off by pressing the ESC
switch.
[ $ I W H U G \ Q D P R P H W H U W H V W L Q J L V
completed, turn the ESC system back
on by pressing the ESC switch again.
1. Crankcase emission control
system
The positive crankcase ventilation
system is employed to prevent air
pollution caused by blow-by gases
being emitted from the crankcase. This
system supplies fresh filtered air to the
crankcase through the air intake hose.
Inside the crankcase, the fresh air mixes
with blow-by gases, which then pass
through the PCV valve into the induction
system.
2. Evaporative emission control
system
The Evaporative Emission Control
System is designed to prevent fuel
vapours from escaping into the
atmosphere.
Canister
Fuel vapours generated inside the fuel
tank are absorbed and stored in the
onboard canister. When the engine is
running, the fuel vapours absorbed in
the canister are drawn into the surge
tank through the purge control solenoid
valve.
Purge Control Solenoid Valve
(PCSV)
The purge control solenoid valve
is controlled by the Engine Control
Module (ECM); when the engine coolant
temperature is low during idling, the
PCSV closes so that evaporated fuel
is not taken into the engine. After
the engine warms up during ordinary
driving, the PCSV opens to introduce
evaporated fuel to the engine.
( 0 , 6 6 , 2 1 & 2 1 7 5 2 / 6 < 6 7 ( 0
Page 648 of 649
9-89
09
3. Exhaust emission control
system
The Exhaust Emission Control System is
a highly effective system which controls
exhaust emissions whilst maintaining
good vehicle performance.
Engine exhaust gas precautions
(carbon monoxide)
[ & D U E R Q P R Q R [ L G H F D Q E H S U H V H Q W Z L W K
other exhaust fumes. Therefore, if
you smell exhaust fumes of any kind
inside your vehicle, have it inspected
and repaired immediately. If you ever
suspect exhaust fumes are coming
into your vehicle, drive it only with
all the windows fully open. Have
your vehicle checked and repaired
immediately.
WARNING
Engine exhaust gases contain carbon
monoxide (CO). Though colourless and
odourless, it is dangerous and could be
lethal if inhaled. Follow the instructions
following to avoid CO poisoning.
[ ' R Q R W R S H U D W H W K H H Q J L Q H L Q F R Q I L Q H G
or closed areas (such as garages) any
more than what is necessary to move
the vehicle in or out of the area.
[ : K H Q W K H Y H K L F O H L V V W R S S H G L Q D Q
open area for more than a short time
with the engine running, adjust the
ventilation system (as needed) to draw
outside air into the vehicle.
[ 1 H Y H U V L W L Q D S D U N H G R U V W R S S H G
vehicle for any extended time with the
engine running.
[ : K H Q W K H H Q J L Q H V W D O O V R U I D L O V W R
start, excessive attempts to restart
the engine may cause damage to the
emission control system.
Operating precautions for catalytic
converters (if equipped)
WARNING
[ $ K R W H [ K D X V W V \ V W H P F D Q L J Q L W H
flammable items under your vehicle.
Do not park, idle, or drive the vehicle
over or near flammable objects, such
as dry grass, paper, leaves, etc.
[ 7 K H H [ K D X V W V \ V W H P D Q G F D W D O \ W L F
system are very hot whilst the engine
is running or immediately after the
engine is turned off. Keep away from
the exhaust system and catalytic
converter as you may get burned.
Also, do not remove the heat sink
around the exhaust system, do not
seal the bottom of the vehicle and
do not coat the vehicle for corrosion
control. It may present a fire risk
under certain conditions.
Your vehicle is equipped with a catalytic
converter emission control device.
Therefore, the following precautions
must be observed:
[ 8 V H R Q O \ 8 1 / ( $ ' ( ' ) 8 ( / I R U S H W U R O
engines.
[ ' R Q R W R S H U D W H W K H Y H K L F O H Z K H Q
there are signs of engine malfunction,
such as misfire or a noticeable loss of
performance.
[ ' R Q R W P L V X V H R U D E X V H W K H H Q J L Q H
Examples of misuse are coasting with
the engine off and descending steep
grades in gear with the engine off.
[ ' R Q R W R S H U D W H W K H H Q J L Q H D W K L J K L G O H
speed for extended periods (5 minutes
or more).
[ ' R Q R W P R G L I \ R U W D P S H U Z L W K D Q \
part of the engine or emission control
system. We recommend that all
inspections and adjustments are
made by a HYUNDAI authorised
repairer.