ignition HYUNDAI I20 2023 Manual PDF
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2023, Model line: I20, Model: HYUNDAI I20 2023Pages: 649, PDF Size: 12.35 MB
Page 532 of 649
8-17
08
Changing tyres
WARNING
A vehicle can slip or roll off of a jack
causing serious injury or death to you
or those nearby. Take the following
safety precautions:
[ Do not get under a vehicle that is
supported by a jack.
[ NEVER attempt to change a tyre in
the lane of traffic. ALWAYS move the
vehicle completely off the road on
level, firm ground away from traffic
before trying to change a tyre. If you
cannot find a level, firm place off
the road, call a towing service for
assistance.
[ Be sure to use the jack provided with
the vehicle.
[ ALWAYS place the jack on the
designated jacking positions on the
vehicle and NEVER on the bumpers
or any other part of the vehicle for
jacking support.
[ Do not start or run the engine whilst
the vehicle is on the jack.
[ Do not allow anyone to remain in the
vehicle whilst it is on the jack.
[ Keep children away from the road
and the vehicle.
Follow these steps to change your
vehicle’s tyre:
1. Park on a level, firm surface.
2. Move the shift lever into P (Park, for
automatic transmission/dual clutch
transmission vehicle) or neutral
(for manual transmission vehicle),
apply the parking brake, and place
the ignition switch in the LOCK/OFF
position.
3. Press the hazard warning flasher
button.
4. Remove the wheel lug nut wrench,
jack, jack handle, and spare tyre from
the vehicle.
OBC3080005
[A] : Block
5. Block both the front and rear of the
tyre diagonally opposite of the tyre
you are changing.
OBC3080006
6. Loosen the wheel lug nuts
counterclockwise one turn each in
the order shown above, but do not
remove any lug nuts until the tyre has
been raised off of the ground.
Page 545 of 649
8-30
Emergency situations
ODN8079020
5. Insert the sealant bottle into the
housing (5) of the compressor so that
the bottle is upright.
6. Ensure that the compressor is
switched off, position 0.
OBC3080011
NOTICE
Securely install the sealant filling hose
to the valve. If not, sealant may flow
backward, possibly clogging the filling
hose.
OBC3N080005
7. Connect between compressor and the
vehicle power outlet using the cable
and connectors (4).
8. With the engine start/stop button
position on or ignition switch position
on, switch on the compressor and let
it run for approximately 5~7 minutes to
fill the sealant up to proper pressure.
(refer to immediately chapter 2).
The inflation pressure of the tyre
immediately filling is unimportant and
will be checked/corrected later.
Be careful not to overinflate the tyre
and stay away from the tyre whilst
filling it.
NOTICE
- Tyre pressure
Do not attempt to drive your vehicle
if the tyre pressure is below 29
PSI(200kpa). This could result in an
accident due to sudden tyre failure.
9. Switch off the compressor.
10. Detach the hoses from the sealant
bottle connector and from the tyre
valve.
Return the Tyre Mobility Kit to its storage
location in the vehicle.
Page 546 of 649
8-31
08
WARNING
Carbon monoxide
Do not leave your vehicle running in
a poorly ventilated area for extended
periods of time.
Carbon monoxide poisoning and
suffocation can occur.
Distributing the sealant
11. Immediately drive approximately
4~6miles (7~10km or, about 10 mins)
to evenly distribute the sealant in the
tyre.
Do not exceed a speed of 50 mph (80
km/h). If possible, do not fall below a
speed of 12 mph (20 km/h).
Whilst driving, if you experience any
unusual vibration, ride disturbance or
noise, reduce your speed and drive with
caution until you can safely pull off the
vehicle on the side of the road.
Call for road side service or towing.
When you use the Tyre Mobility Kit, the
tyre pressure valve and wheel may be
damaged by sealant, remove the sealant
stained. We recommend that the tyre
pressure valve and wheel be inspected
by an authorized HYUNDAI dealer.
Checking the tyre inflation
pressure
1. After driving approximately 4 ~6miles
(7~10km or about 10min), stop at a
safety location.
2. Connect connection hose (10) of the
compressor directly to the tyre valve.
3. Plug the compressor power cord into
the vehicle power outlet.
4. Adjust the tyre inflation pressure to
the recommended tyre inflation.
With the ignition switched on, proceed
as follows.
- To increase the inflation pressure :
Switch on the compressor, position
I. To check the current inflation
pressure setting, briefly switch off
the compressor.
i Information
The pressure gauge may show higher than
actual reading when the compressor is
running. To get an accurate tyre pressure,
the compressor needs to be turned off.
NOTICE
- Tyre pressure valve
We recommend that you use the
sealant of tyre mobility kit from a
HYUNDAI authorised repairer. The
sealant on the tyre pressure valve and
wheel should be removed when you
replace the tyre with a new one and
we recommend that the tyre pressure
valve be inspected by an authorized
HYUNDAI dealer.
Page 548 of 649
8-33
08
When towing your vehicle in an
emergency without wheel dollies:
1. Place the ignition switch in the ACC
position.
2. Place the shift lever in N (Neutral).
3. Release the parking brake.
CAUTION
Failure to place the shift lever in N
(Neutral) may cause internal damage to
the transmission.
Removable towing hook
OBC3080017
1. Open the tailgate, and remove the
towing hook from the tool case.
OBC3080018
2. Remove the hole cover by pressing
the lower part of the cover on the
bumper.
3. Install the towing hook by turning it
clockwise into the hole until it is fully
secured.
4. Remove the towing hook and install
the cover after use.
Page 549 of 649
8-34
Emergency situations
Emergency towing
OBC3080019
„Front
„Rear
OBC3080020
If towing is necessary, we recommend
you have it done by a HYUNDAI
authorised repairer or a commercial tow
truck service.
If towing service is not available in
an emergency, your vehicle may be
temporarily towed using a cable or chain
secured to the emergency towing hook
at the front (or rear) of the vehicle.
Use extreme caution when towing the
vehicle with a cable or chain. A driver
must be in the vehicle to steer it and
operate the brakes.
Towing in this manner may be done
only on hard-surfaced roads for a short
distance and at low speeds. Also, the
wheels, axles, power train, steering and
brakes must all be in good condition.
CAUTION
The driver must be in the vehicle for
steering and braking operations when
the vehicle is being towed. Passengers
other than the driver must not be in the
vehicle.
Always follow these emergency towing
precautions:
[ Place the ignition switch in the ACC
position so the steering wheel is not
locked.
[ Place the shift lever in N (Neutral).
[ Release the parking brake.
[ Depress the brake pedal with more
force than normal since you will have
reduced braking performance.
[ More steering effort will be required
because the power steering system
will be disabled.
[ Use a vehicle heavier than your own to
tow your vehicle.
[ The drivers of both vehicles should
communicate with each other
frequently.
[ Before emergency towing, check that
the hook is not broken or damaged.
[ Fasten the towing cable or chain
securely to the hook.
[ Do not jerk the hook. Apply steady and
even force.
Page 556 of 649
8-41
08
Modalities for exercising data
subject’s rights
The data subject (the vehicle’s owner)
has a right of access to data and as
appropriate to request the rectification,
erasure or blocking of data, concerning
him or her, the processing of which
does not comply with the provisions
of Directive 95/46/EC. Any third
parties to whom the data have been
disclosed have to be notified of such
rectification, erasure or blocking carried
out in compliance with this Directive,
unless it proves impossible or involves a
disproportionate effort.
The data subject has a right to complain
to the competent data protection
authority if he or she considers that his
or her rights have been infringed as a
result of the processing of his or her
personal data.
Contact service responsible for handling
access requests (if any): Not applicable
Pan-European eCall System
OBC3N080014
Elements of the Pan-European
eCall system, installed in passenger
compartment:
(1) SOS button
(2) LED
SOS button: the driver/passenger makes
an emergency call to the single duty
dispatch service by pressing the button.
LED: the red and green LED illuminates
for 3 seconds when the ignition switch
is in the ON position. After that they will
switch off at normal operation of the
system.
If there are some problems in the
system, the LED remains in red.
Page 566 of 649
9-7
09
WARNING
Performing maintenance work on a
vehicle can be dangerous. If you lack
sufficient knowledge and experience
or the proper tools and equipment
to do the work, we recommend that
the system be serviced by a HYUNDAI
authorised repairer. ALWAYS follow
these precautions for performing
maintenance work:
[ 3 D U N \ R X U Y H K L F O H R Q O H Y H O J U R X Q G
move the shift lever into the P (Park,
for automatic transmission/dual
clutch transmission vehicle) position,
apply the parking brake, and place
the ignition switch in the LOCK/OFF
position.
[ % O R F N W K H W \ U H V I U R Q W D Q G E D F N W R
prevent the vehicle from moving.
Remove loose clothing or jewellery
that can become entangled in
moving parts.
[ , I \ R X P X V W U X Q W K H H Q J L Q H G X U L Q J
maintenance, do so out doors or in an
area with plenty of ventilation.
[ . H H S I O D P H V V S D U N V R U V P R N L Q J
materials away from the battery and
fuel-related parts.The following lists are vehicle checks
and inspections that should be
performed by the owner or a HYUNDAI
authorised repairer at the frequencies
indicated to help ensure safe,
dependable operation of your vehicle.
Any adverse conditions should be
brought to the attention of your dealer
as soon as possible.
These Owner Maintenance vehicle
checks are generally not covered by
warranties and you may be charged for
labour, parts and lubricants used.
Owner maintenance schedule
When you stop for fuel:
[ Check the coolant level in the engine
coolant reservoir.
[ Check the windscreen washer fluid
level.
[ Check for low or under-inflated tyres.
[ Check the radiator and condenser.
Check if the front of the radiator and
condenser are clean and not blocked
with leaves, dirt or insects, etc.
If any of the above parts are extremely
dirty or you are not sure of their
condition, we recommend that
you contact a HYUNDAI authorised
repairer.
WARNING
% H F D U H I X O Z K H Q F K H F N L Q J \ R X U H Q J L Q H
coolant level when the engine is hot.
This may result in coolant being blown
out of the opening and cause serious
burns and other injuries.
OWNER MAINTENANCE
Page 569 of 649
9-10
Maintenance
Engine oil and filter
The engine oil and filter should be
changed at the intervals specified in the
maintenance schedule. If the vehicle
is being driven in severe conditions,
more frequent oil and filter changes are
required.
Drive belts
Inspect all drive belts for evidence
of cuts, cracks, excessive wear or oil
saturation and replace if necessary.
Drive belts should be checked
periodically for proper tension and
adjusted as necessary.
CAUTION
When you are inspecting the belt, place
the ignition switch to the lock/off or
ACC position.
Fuel filter (Except Europe)
A clogged filter can limit the speed
at which the vehicle may be driven,
damage the emission system and cause
multiple issues such as hard starting.
If an excessive amount of foreign
matter accumulates in the fuel tank, the
filter may require replacement more
frequently.
After installing a new filter, run the
engine for several minutes, and
check for leaks at the connections.
We recommend that the fuel filter be
replaced by a HYUNDAI authorised
repairer.
Fuel filter (For Europe)
This petrol powered vehicle is equipped
with a lifetime fuel filter that is
integrated with the fuel tank. Regular
maintenance or replacement is not
needed; however, the quality of fuel
used may impact the frequency of
maintenance needed. If there are any
fuel related problems like fuel flow
restriction, surging, loss of power,
hard starting problem etc, fuel filter
inspection or replacement may be
needed. We recommend the fuel filter
be inspected or replaced by a HYUNDAI
authorised repairer.
Fuel lines, fuel hoses and
connections
Check the fuel lines, fuel hoses and
connections for leakage and damage.
We recommend that the fuel lines, fuel
hoses and connections be replaced by a
HYUNDAI authorised repairer.
Vapour hose and fuel filler cap
The vapour hose and fuel filler cap
should be inspected at those intervals
specified in the maintenance schedule.
Make sure that a new vapour hose or
fuel filler cap is correctly replaced.
EXPLANATION OF SCHEDULED MAINTENANCE ITEMS
Page 570 of 649
9-11
09
Vacuum crankcase ventilation
hoses (if equipped)
Inspect the surface of hoses for
evidence of heat and/or mechanical
damage. Hard and brittle rubber,
cracking, tears, cuts, abrasions, and
excessive swelling indicate deterioration.
Particular attention should be paid to
examine those hose surfaces nearest to
high heat sources, such as the exhaust
manifold.
Inspect the hose routing to assure that
the hoses do not come in contact with
any heat source, sharp edges or moving
component which might cause heat
damage or mechanical wear. Inspect
all hose connections, such as clamps
and couplings, to make sure they are
secure, and that no leaks are present.
Hoses should be replaced immediately if
there is any evidence of deterioration or
damage.
Air cleaner filter
We recommend that the air cleaner filter
be replaced by a HYUNDAI authorised
repairer.
Spark plugs
(for petrol engine)
Make sure to install new spark plugs of
the correct heat range.
When assembling parts, be sure to
wipe out foreign substances inside
and outside of the boot bottom of the
ignition coil and the insulator of the
spark plug with a soft cloth to prevent
contamination of the spark plug
insulator.
WARNING
Do not disconnect and inspect spark
plugs when the engine is hot. You may
burn yourself.
Cooling system
Check the cooling system parts, such
as radiator, coolant reservoir, hoses and
connections for leakage and damage.
Replace any damaged parts.
Engine coolant
The coolant should be changed at the
intervals specified in the maintenance
schedule.
Manual transmission fluid/iMT
system actuator fluid
(if equipped)
Inspect the Manual transmission fluid/
iMT system actuator fluid according to
the maintenance schedule.
Automatic transmission fluid
(if equipped)
Automatic transmission fluid should
not be checked under normal usage
conditions.
We recommend that the automatic
transmission fluid is changed by a
HYUNDAI authorised repairer according
to the maintenance schedule.
i Information
$ X W R P D W L F W U D Q V P L V V L R Q I O X L G F R O R X U L V U H G
Z K H Q Q H Z
$ V W K H Y H K L F O H L V G U L Y H Q W K H D X W R P D W L F
W U D Q V P L V V L R Q I O X L G Z L O O E H J L Q W R O R R N
G D U N H U
7 K L V L V D Q R U P D O F R Q G L W L R Q , W G R H V Q R W
Q H H G W R E H U H S O D F H G E D V H G R Q W K H F R O R X U
F K D Q J H
Page 588 of 649
9-29
09
WARNING
To prevent SERIOUS INJURY or DEATH
to you or bystanders, always follow
these precautions when working near
or handling the battery:
Always read and follow
instructions carefully when
handling a battery.
Wear eye protection designed
to protect the eyes from acid
splashes.
Keep all flames, sparks, or
smoking materials away from
the battery.
Hydrogen is always present in
battery cells, is highly
combustible, and may explode
if ignited.
% D W W H U L H V F R Q W D L Q V X O I X U L F D F L G
which is highly corrosive. Do
not allow acid to contact your
eyes, skin or clothing.
If acid gets into your eyes, flush your
eyes with clean water for at least 15
minutes and get immediate medical
attention. If acid gets on your skin,
thoroughly wash the area. If you
feel pain or a burning sensation, get
medical attention immediately.
[ When lifting a plastic-cased battery,
excessive pressure on the case may
cause battery acid to leak. Lift with a
battery carrier or with your hands on
opposite corners.
[ Do not attempt to jump start your
vehicle if your battery is frozen.
[ NEVER attempt to recharge the
battery when the vehicle’s battery
cables are connected to the battery.
[ The electrical ignition system works
with high voltage. NEVER touch these
components with the engine running
or when the Engine Start/Stop button
is in the ON position.
[ Do not allow the (+) and (-) jumper
cables to touch. It may cause sparks.
[ The battery may rupture or explode
when you jump start with a low or
frozen battery.
[ Leaked battery electrolyte due to
repeated driving on sharp curves
(e.g. on circuits) may cause safety
problem. Avoid repeated driving on
sharp curves.
NOTICE
If you connect unauthorised electronic
devices to the battery, the battery may
be discharged. Never use unauthorised
devices.
% $ 7 7 ( 5 <