ignition Hyundai Matrix 2004 Owner's Manual
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2004, Model line: Matrix, Model: Hyundai Matrix 2004Pages: 317, PDF Size: 5.12 MB
Page 12 of 317
FEATURES OF YOUR HYUNDAI
1- 4
HFC2004
UNLOCK
LOCK
B040A02Y-AAT DOOR LOCKS WARNING:
o Unlocked doors can be dangerous. Be-
fore you drive away (especially if thereare children in the car), be sure that allthe doors are securely closed and lockedso that the doors cannot be inadvertentlyopened from the inside. This helps en-sure that the doors will not be openedaccidentally. Also, when combined withthe proper use of seat belts, locking thedoors helps keep occupants from beingejected from the car in case of an acci-dent.
o Before opening the door, always look for and avoid oncoming traffic.
o In case of accident the door is unlocked automatically (If installed)
B040B01A-AAT Locking and Unlocking Front Doors With a Key
operation of the ignition key. For example, turn the ignition key once for digit number"1", and twice for "2", and so on. However,for the digit number "0", you must turn theignition key for 10 times.
2. Wait for 3~10 seconds.
3. You may set the remaining number of digits by following the same procedures 1 and 2.
4. If all of four digits have been tried success- fully, turn the ignition key "ON" and checkthat the immobilizer indicator illuminates.From this time, you have to start your enginewithin 30 seconds. If you start your engineafter 30 seconds, your engine will not start.
NOTE:If the engine dies while driving after limphome procedure, you can start your enginewithin 8 seconds without limp home proce-dure again.
5. If the immobilizer indicator blinks for five seconds, you have to try the limp home procedure again from the beginning.
After doing the limp home procedure, you haveto consult with your authorized Hyundai dealeras soon as possible. CAUTION:
o If you fail to try the limp home procedure with the sequence of three times, youhave to wait for about one hour to do thelimp home procedure again.
o If you cannot start your engine in spite of limp home procedure, have your vehicletowed by an authorized Hyundai dealer.
B880D02A-GAT Limp home procedures In case the immobilizer warning indicator blinks for five seconds when the ignition key isturned to "ON" position, this indicates that theimmobilizer system is out of order. And youcannot start the engine without the limp homeprocedures with ignition key. The following procedure is how to start the engine with the function of the limp home. (0,1, 2, 3 as a sample password). NOTE: You can get the limp home password whenthe vehicle is first delivered to you. If you donot have the password, consult your autho-rized Hyundai dealer.
1. To set the password you may turn theignition key "ON" and then turn it "OFF" according to the digit numbers, then theimmobilizer indicator will blink along with the
B880D01FC
Page 13 of 317
FEATURES OF YOUR HYUNDAI 1- 5
HFC2009
o The door can be locked or unlocked with akey.
o Lock the door by turning the key toward the front of the vehicle and unlock it by turning the key toward the rear.
B040C01FC-GAT Locking From the Outside
The doors can be locked without a key.
To lock the doors first push the inside lock switch to the "LOCK" position, so that the redmark on the switch is not visible, then close thedoor.The door will not lock if the key is left in theignition switch when the front doors close. Thisis normal. (If installed) NOTE:
o When locking the door this way, be care- ful not to lock the door with the ignitionkey left in the vehicle. B040D01FC-GAT Locking From the Inside To lock the doors from the inside, simply close the door and push the lock switch to the "LOCK"position. When this is done, neither the outsidenor the inside door handle can be used. NOTE: When the door is locked, the red mark on theswitch is not visible and the character"LOCK" on the switch is visible.
B040D01FC
UNLOCK
LOCK B040E03A-AAT CHILD-PROTECTOR REAR DOOR LOCK
Your Hyundai is equipped with a "child-protec- tor" rear door lock assembly. When the lock mechanism is engaged, the rear door cannotbe opened from the inside. It's use is recom-mended whenever there are small children inthe rear seat. To engage the child-protector feature so that the door cannot be opened from the inside,move the child-protector lever to the " "position and close the door. Move the lever tothe opposite direction of the " " position whennormal door operation is desired. If you wish to be able to open the door from the outside, the outside door handle will functionnormally.HFC2006
o To protect against theft, always remove
the ignition key, close all windows, and lock all doors and the tail gate whenleaving your vehicle unattended.
Page 14 of 317
FEATURES OF YOUR HYUNDAI
1- 6 B070A01A-AAT THEFT-ALARM SYSTEM (If Installed) This system is designed to provide protection from unauthorized entry into the car. This sys-tem is operated in three stages: the first is the"Armed" stage, the second is the "Alarm" stage,and the third is the "Disarmed" stage. If trig-gered, the system provides an audible alarmwith blinking of the turn signal lights. B070B01O-GAT Armed Stage
HFC2003
LOCK
UNLOCK
B040H02L-GAT
Speed Sensing Auto Door Locking (If Installed) When the speed of the vehicle keeps above 40KM/H for 2-3 seconds, it will automaticallylock all doors for driver and passenger's safety.But, the ignition key is removed, it will automati-cally unlock all doors.
Park the car and stop the engine. Arm thesystem as described below.
1) Remove the ignition key from the ignition
switch.
2) Make sure that the engine hood and tail gate are locked.
3) Lock the doors using the transmitter of the keyless entry system.
After completion of the steps above, the turn signal lights will blink once to indicate that thesystem is armed. NOTE:
1) If any door, tail gate or engine hood remains open, the system will not bearmed.
2) If this happens, rearm the system as described above.
CAUTION:Do not arm the system until all passengershave left the car. If the system is armedwhile a passenger(s) remains in the car, thealarm may be activated when the remainingpassenger(s) leaves the car.
B040G01FC
B040G01FC-GAT
Central Door Lock (If Installed) The central door locking is operated by pushing the driver's door lock switch toward the front or
rear of the vehicle. If the passenger and reardoors are open when the switch is pushed, the
door will remain locked when closed. NOTE:
o When pushing the switch toward the
rear, all doors and tail gate will unlock.When pushing the switch toward thefront, all doors and tail gate will lock.
o When the door is unlocked, the red mark on the switch is visible and the character"LOCK" on the switch is not visible.
o The central door locking is operated by turning the key (with theft-alarm system:driver's door and passenger's door, with-out theft-alarm system: driver's door only)toward the front or rear of the vehicle.
Page 15 of 317
FEATURES OF YOUR HYUNDAI 1- 7
After completion of the step above, the turn signal lights will blink twice to indicate that thesystem is disarmed. NOTE: Once the system has been disarmed, it can not be rearmed except by repeating thearming procedures. CAUTION: Only the transmitter can disarm the armedstage. If the transmitter does not disarmthe system, it is necessary to take thefollowing steps;
1. Unlock the door with the key, which willcause, the alarm to be activated.
2. Insert the key in the ignition key cylinder and turn the ignition key to "ON" posi- tion.
3. Wait for 30 seconds. After completing the steps above, the sys- tem will be disarmed.
B070D02O-AAT Disarmed Stage
B070C01FC-GAT Alarm StageThe alarm will be activated if any of the following occurs while the car is parked and thesystem is armed.
1) A front or rear door is opened without using
the transmitter.
2) The tail gate is opened without using the transmitter.
3) The engine hood is opened. The alarming horn will sound and the turn signal light will blink continuously for 27 seconds (E.Conly/ Except E.C 3 times). To turn off thesystem, unlock the door or tail gate with thetransmitter.
3A9BA21
B070F01A-GAT Keyless Entry System (If Installed) Locking doors
1. Close all doors.
2. Push the "LOCK" button on the transmitter.
3. At the same time all doors lock, the turnsignal lights will blink once to indicate thatthe system is armed. B070E02HP-GAT Replacing the batteryWhen the transmitter's battery begins to get weak, it may take several pushes on the buttonto lock or unlock the doors, and the LED will notlight. Replace the battery as soon as possible. Battery type : CR2032
Replacement instructions:
1. Separate the case with a blade screwdriver as shown in the illustration.
MSO-0048-1
Screwdriver
Unlocking doors
1. Push the "UNLOCK" button on the transmit-
ter.
2. At the same time all doors unlock, the turn signal light will blink twice to indicate that the system is disarmed.
The system will be disarmed when the driver'sor passenger's door is unlocked by depressingthe "UNLOCK" button on the transmitter.
Page 16 of 317
FEATURES OF YOUR HYUNDAI
1- 8 To raise or lower the window, turn the window regulator handle clockwise or counterclock-wise. WARNING: When opening or closing the windows, makesure your passenger's arms, hands andbody are safely out of the way.
B060A01E-AAT POWER WINDOWS (If Installed)
Close Open
B060A01FC
The power windows operate when the ignition key is in the "ON" position. The main switchesare located on the driver's armrest and controlthe front and rear windows on both sides of thevehicle. The windows may be opened by de-pressing the appropriate window switch andclosed by pulling up the switch. To open thewindow on the driver's side, press the switch(1)down. The window moves as long as the switchis operated.
(1)
HFC2013
In order to prevent operation of the passenger front and rear windows, a window lock switch isprovided on the armrest of the driver's door. Todisable the power windows, press the window
lock switch.To revert to normal operation, press the win-dow lock switch a second time. Auto-Down Window (Driver's Side) The Auto-Down window is moved to its fully open position by pushing the switch. To stop atthe desired position push the switch again. WARNING:
1) Be careful that someone's head, hands and body are not trapped by a closingwindow.
2) Never try to operate the main switch on the driver's door and the individual doorwindow switch in opposing directions atthe same time. If this is done, the windowwill stop and cannot be opened or closed.
B050A01A-AAT WINDOW GLASS
B050A01FC
2. Remove the old battery from the case and
note the polarity. Make sure the polarity of the new battery is the same(+side facingdown), then insert it in the transmitter.
MSO-0048-2
Case
Battery
Page 17 of 317
FEATURES OF YOUR HYUNDAI 1- 9
B080D02A-AAT Adjustable Headrests
HFC2028
Lock knob
B080A01FC-GAT ADJUSTABLE SEATSWARNING: Never attempt to adjust the seat while thevehicle is moving. This could result in lossof control, or an accident which may causedeath, serious injury, or property damage.
HFC2024
B080B02FC-GAT FRONT SEATS Adjusting Seat Forward and Rearward To move the seat toward the front or rear, pull the lock release lever upward. This will releasethe seat on its track so you can move it forwardor rearward to the desired position. When you B080C01A-AAT Adjusting Seatback Angle To recline the seatback, lean forward to take your weight off it, then pull up on the reclinercontrol lever at the outside edge of the seat.Now lean back until the desired seatback angleis achieved. To lock the seatback into position,release the recliner control lever.
HFC2025
find the position you want, release the lever and slide the seat forward or rearward on its trackuntil it locks into the desired position and cannotbe moved further. WARNING: To ensure the seat is locked securely, at-tempt to move the seat forward or rearwardwithout using the lock release lever.
WARNING:To minimize risk of severe injury in theevent of a collision or a sudden stop, boththe driver and passenger seatbacks shouldalways be in an upright position while thevehicle is in motion. The protection provid-ed by the seat belts and airbags in a frontalcollision may be reduced significantly whenthe seatbacks are reclined. There is greaterrisk that the driver and passenger will slideunder the seat belt which may result inserious injury if a crash occurs when theseatbacks are reclined. The seat belt cannotprovide full protection to an occupant if theseat back is reclined.
3) Do not leave children alone in the car.
Always remove the ignition key for theirsafety.
Headrests are designed to help reduce the risk of neck injuries.
Page 32 of 317
FEATURES OF YOUR HYUNDAI
1- 24 CAUTION:
o Because the sensor that activates the
SRS airbag is connected with the pre-tensioner seat belt, the SRS airbag warn-ing light on the instrument panel willblink for approximately 6 seconds afterthe ignition key has been turned to the"ON" position, and then it should turnoff.
o If the pre-tensioner seat belt is not work- ing properly, this warning light will illu-minate even if there is no malfunction ofthe SRS airbag system . If the SRS airbagwarning light does not illuminate whenthe ignition key is turned to "ON", or if itremains illuminated after blinking forapproximately 6 seconds, or if it illumi-nates while the vehicle is being driven,please have an authorized Hyundai deal-er inspect the pre-tensioner seat belt orSRS airbag system as soon as possible. WARNING:
o Pre-tensioners are designed to operate
only one time. After activation, pre-tensioner seat belts must be replaced.All seat belts, of any type, should alwaysbe replaced after they have been wornduring a collision.
o The pre-tensioner seat belt assembly mechanisms become hot during activa-tion. Do not touch the pre-tensioner seatbelt assemblies for several minutes afterthey have been activated.
o Do not attempt to inspect or replace the pre-tensioner seat belts yourself. Thismust be done by an authorized Hyundaidealer.
o Do not strike the pre-tensioner seat belt assemblies.
o Do not attempt to service or repair the pre-tensioner seat belt system in anymanner.
o Improper handling of the pre-tensioner seat belt assemblies, and failure to heedthe warnings to not strike, modify, in-spect, replace, service or repair the pre-tensioner seat belt assemblies may leadto improper operation or inadvertent ac-tivation and serious injury.
o Always wear the seat belts when driving or riding in a motor vehicle.
NOTE:
o Both the driver's and front passenger'spre-tensioner seat belts will be activatedin certain frontal collisions. The pre-tensioner seat belts can be activatedwith the airbags. The pre-tensioners willbe activated under these conditions evenif the seat belts are not being worn at thetime of the collision.
o When the pre-tensioner seat belts are activated, a loud noise may be heard andfine dust, which may appear to be smoke,may be visible in the passenger compart-ment. These are normal operating condi-tions and are not hazardous.
o Although it is harmless, the fine dust may cause skin irritation and should notbe breathed for prolonged periods. Washyour hands and face thoroughly after anaccident in which the pre-tensioner seatbelts were activated.
Page 34 of 317
FEATURES OF YOUR HYUNDAI
1- 26
SSA1110D
The SRS service reminder indicator (SRI) on the instrument panel will blink for about 6 sec-onds after the ignition key is turned to the "ON"position or after the engine is started, afterwhich the SRI should go out.
SSA1110C
The SRS consists of the following components: - Driver's Airbag Module
- Passenger's Airbag Module
- SRS Service Reminder Indicator (SRI)
- SRS Control Module (SRSCM)
The SRSCM continually monitors all elementswhile the ignition is "ON" to determine if a frontalor near-frontal impact is severe enough torequire airbag deployment. B240B01FC-GAT SRS Components and Functions
SSA1110B
o Do not tamper with or disconnect SRS
wiring, or other components of the SRS system. Doing so could result in injury,due to accidental firing of the airbags orby rendering the SRS inoperative.
o Do not install a child restraint system in the front passenger seat position. Achild restraint system must never beplaced in the front seat. The infant orchild could be severely injured or killedby an airbag deployment in case of anaccident.
o Do not allow children to ride in the front passenger seat. If older children (teenag-ers and older) must ride in the front seat,make sure they are always properly beltedand that the seat is moved back as far aspossible.
o For maximum safety protection in all types of crashes, all occupants includ-ing the driver should always wear theirseat belts whether or not an airbag isalso provided at their seating position tominimize the risk of severe injury ordeath in the event of a crash. Do not sit orlean unnecessarily close to the airbagwhile the vehicle is in motion.
o The SRS airbag system must deploy very rapidly to provide protection in a crash.If an occupant is out of position becauseof not wearing a seat belt, the airbag mayforcefully contact the occupant causingserious or fatal injuries.
Page 35 of 317
FEATURES OF YOUR HYUNDAI 1- 27
parts. If the liquid from the air freshener does leak onto these areas, wash them withwater immediately. WARNING:
o When the SRS is activated, there may be
a loud noise and fine dust will be re-leased throughout the vehicle. These con-ditions are normal and are not hazard-ous. However, the fine dust generatedduring airbag deployment may causeskin irritation. Wash your hands and facethoroughly with lukewarm water and amild soap after an accident in which theairbags were deployed.
o The SRS can function only when the ignition key is in the "ON" position. If theSRS SRI does not come on, or continu-ously remains on, after flashing for about6 seconds when the ignition key is turnedto the "ON" position, or after the engineis started, comes on while driving, theSRS is not working properly. If this oc-curs, have your vehicle immediately in-spected by your Hyundai dealer.
o Before you replace a fuse or disconnect a battery terminal, turn the ignition key tothe "LOCK" position or remove the igni-tion key. Never remove or replace the airbag related fuse(s) when the ignition keyis in the "ON" position. Failure to heedthis warning will cause the SRS SRI toilluminate.
Passenger's Airbag
YR10353A
After complete inflation, the airbag immediately starts deflating, enabling the driver to maintainforward visibility. CAUTION: When installing a container of liquid airfreshener inside a vehicle, do not place itnear the instrument cluster nor on the in-strument panel pad surface. If there is anyleakage from the air freshener onto theseareas (instrument cluster, instrument panelpad or air ventilator), it may damage these
CAUTION:Do not install or place any accessories (drinkholder, cassette holder, sticker, etc) on thefront passenger's panel above the glovebox in a vehicle with passenger's air bag.Such objects may become dangerous pro-jectiles and cause injury if the passenger'sair bag inflates.
Passenger's Airbag
The airbag modules are located both in the center of the steering wheel and in the frontpassenger's panel above the glove box. Whenthe SRSCM detects a considerable impact tothe front of the vehicle, it will automaticallydeploy the airbags.
Upon deployment, tear seams molded directlyinto the pad covers will separate under pres-sure from the expansion of the airbags. Furtheropening of the covers then allows full inflationof the airbags. A fully inflated airbag in combination with a properly worn seat belt slows the driver's or thepassenger's forward motion, thus reducing therisk of head or chest injury.
B240B04FC
Page 36 of 317
FEATURES OF YOUR HYUNDAI
1- 28
o Do not place any objects over the airbag or between the airbag and yourself.
o Do not place any objects (an umbrella, bag, etc.) between the front door and the front seat. Such objects may becomedangerous projectiles and cause injury ifthe supplemental side impact air baginflates.
o To prevent unexpected deployment of the side impact air bag that may result inpersonal injury, avoid impact to the sideairbag sensor when the ignition key ison.
B240C03Y-GAT SRS CareThe SRS is virtually maintenance-free and there are no parts you can safely service byyourself. The entire SRS system must be in-spected by an authorized Hyundai dealer 10years after the date that the vehicle was manu-factured. Any work on the SRS system, such as remov- ing, installing, repairing, or any work on thesteering wheel must be performed by a quali-fied Hyundai technician. Improper handling ofthe SRS system may result in serious personalinjury.
HFC2092
Side airbag sensor
WARNING:
o For best protection from the side impact airbag system and to avoid being injuredby the deploying side impact airbag, bothfront seat occupants should sit in anupright position with the seat belt prop-erly fastened. The driver's hands shouldbe placed on the steering wheel at the9:00 and 3:00 o'clock positions. Thepassenger's arms and hands should beplaced in their laps.
o Do not use any accessory seat covers.
o Use of seat covers could reduce or pre- vent the effectiveness of the system.
o Do not install any accessories on the side or near the side impact airbag.
o Do not use excessive force on the side of the seat.
B990B03Y-GAT Side Impact Airbag (If Installed)B990B02Y
Your Hyundai is equipped with a side airbag in each front seat. The purpose of the airbag is toprovide the vehicle's driver and/or the frontpassenger with additional protection than thatoffered by the seatbelt alone. The side impactairbags are designed to deploy only duringcertain side impact collisions, depending on thecrash severity, angle, speed and point of im-pact. The air bags are not designed to deploy inall side impact situations.