lock HYUNDAI PALISADE 2023 Owners Manual

Maintenance9-52
Engine compartment fuse panel
(Engine room junction block)
B0469KO03
Inside the fuse/relay box cover, you can
find the fuse/relay label describing fuse/
relay names and ratings.
Information
Not all fuse panel descriptions in this
manual may be applicable to your vehicle;
the information is accurate at the time of
printing. When you inspect the fuse panel
in your vehicle, refer to the fuse panel
label.
A0468EU01

09
9-53
Engine compartment fuse panel
Fuse NameFuse
Rating Protected Component
MULTI
FUSE
-1 MDPS 100A MDPS Unit
COOLING FAN 1 80A Cooling Fan Relay (600W) EPB 1 60A EPB Control ModuleB+4 50A ICU Junction Block
B+3 50A ICU Junction BlockB+2 50A ICU Junction Block (IPS 2,8,9,10,11,13)
EOP 40A Electronic Oil Pump Module
- 40A Not Used
TRAILER 1 40A Trailer Lamp
EPB 2 40A EPB Control Module
MULTI
FUSE-2 B+1 50A
ICU Junction Block((IPS1,3,4,5,6,7), Long/
Short Term Load Latch Relay)
- 50A Not Used
COOLING FAN 2 50A Cooling Fan Relay (400W) FUEL HEATER 30A Fuel Heater Relay
FUSE B+5
50A ICU Junction Block(DOOR LOCK)
BLOWER (FRT) 40A Blower Relay (FRT)
BLOWER (RR 1) 40A Blower Relay (RR) REAR HEATED 40A Rear HTD Relay IG2 40A Start Relay, ICU Junction Block
3rd ROW
SEAT FOLDING 30A 3rd ROW Seat Folding Unit
INVERTER 30A AC Inverter Unit
TRAILER 4 30A Trailer Lamp POWER
LIFTGATE 30A Power Liftgate Module
E-SHIFTER 1 40A Electronic Transmission
PTC HEATER 1 30A PTC Heater Relay

Maintenance9-54
Fuse Name Fuse
Rating Protected Component
FUSE PT
C HEATER 2 30A PTC Heater Relay
PTC HEATER 3 30A PTC Heater Relay TRAILER 5 30A Trailer Lamp
FUEL PUMP 20A Fuel Pump Relay AWD 20A AWD ECM
HEATED NOZZLE 10A Heated Nozzle Unit B/ALARM HORN 15A Burglar Alarm Horn Relay
ACC 3 15A 2ND USB Charger
TCU 1 15A TCM
TRAILER 2 15A Trailer Lamp
TRAILER 3 15A Trailer Lamp ECU 6 15A ECM
AMS 10A Battery Sensor
A/C 2 10A Front A/C Control Module (Auto)
HEATED
MIRROR 10ADriver/Passenger Power Side view Mirror,
Front A/C Control Module
BLOWER (RR 2) 10A Rear A/C Control Module
E-SHIFTER 2 10A Electronic Transmission
WIPER (FRT) 2 10A IBU, ECM - 10A Not Used
PCB ACC 1
40A PCB Block (ACC1 Relay)
ACC 2 40A PCB Block (ACC2 Relay) ECU 5 30A ECM (Main Relay)
DCU 4 40A Doosing Control Unit (DCU Relay)
IG1 40A PCB Block (IG1 Relay)
WIPER 1 (FRT) 30A PCB Block (Wiper Main Relay) HORN 15A PCB Block (Horn Relay)
A/C 1 10A PCB Block (A/CON Relay)
ACC 4 10A USB Charger_luggage_LH/RH

09
9-55
Fuse NameFuse
Rating Protected Component
PCB POWER
OUTLET 2 20
A 2ND POWER OUTLET#2
POWER
OUTLET 1 20A 2ND POWER OUTLET#1
ICU 10A PCB Block (ACC FUSE - AMP, ETC)
SENSOR 1 10A Fuel Pump Relay
SENSOR 2 10A [L3.8 GDI] A/C Comp Relay, Variable Intake
Solenoid Valve #1/#2, Oil Pump Solenoid
Valve, Oxygen Sensor Down #1/#2, Oil
Control Valve #1/#2(Intake/Exhaust),
Electronic Thermostat Heater, Purge Control
Solenoid Valve
SENSOR 5 10A Oxygen Sensor Up #1/#2, CCV
DCU 1 20A Doosing Control Unit
DCU 2 20A Doosing Control Unit
DUC 3 15A Doosing Control Unit
TCU 2 10A TCM, Electronic Transmission
POWER
OUTLET 3 20A LUGGAGE POWER OUTLET
POWER
OUTLET 4 20A 1ST POWER OUTLET
SENSOR 4 15A [L3.8 GDI] Cooling Fan Controller ECU 1 20A ECM
PCB ECU 2 20A [L3.8 GDI] ECM
ECU 3 20A [L3.8 GDI] ECM
IGN COIL 20A [L3.8 GDI] Ignition Coil #1/#2/#3/#4/#5/#6 EPB 3 10A EPB Control Module
SENSOR 6 10A Electronic Oil Pump ECU 4 10A ECM

09
9-59
Tail/Stop lamp and turn signal lamp
(Type A)
B0474EU01
1. Turn off the engine.
2. Open the liftgate.
3. Loosen the lamp assembly retaining screws with a cross-tip screwdriver.
4. Remove the rear combination lamp assembly from the body of the
vehicle.
5. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
B0474EU02
6. Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
7. Insert a new bulb by inserting it into the socket and rotating it until it locks
into place. 8. Install the socket into the assembly by
aligning the tabs on the socket with
the slots in the assembly. Push the
socket into the assembly and turn the
socket clockwise.
9. Reinstall the lamp assembly to the body of the vehicle.
Tail lamp, stop lamp, turn signal
lamp and garnish lamp (Type B)
If the LED lamp does not operate, have
the system checked by an authorized
HYUNDAI dealer.
The LED lamps cannot replaced as a
single unit because it is an integrated
unit. The LED lamps has to be replaced
with the unit.
A skilled technician should check or
repair the LED lamp, for it may damage
related parts of the vehicle.
Side maker lamp
If the LED lamp does not operate, have
the system checked by an authorized
HYUNDAI dealer.
The LED lamps cannot replaced as a
single unit because it is an integrated
unit. The LED lamps has to be replaced
with the unit.
A skilled technician should check or
repair the LED lamp, for it may damage
related parts of the vehicle.
Reverse lamp
If the light bulb does not operate, have
the vehicle checked by an authorized
HYUNDI dealer.

Maintenance9-60
High Mounted Stop Lamp
Replacement
B0475KO01
If the LED lamp M does not operate, have
the system inspected by an authorized
HYUNDAI dealer.
The LED lamps cannot be replaced as
a single unit because it is an integrated
unit. The LED lamps has to be replaced
with the unit.
A skilled technician should check or
repair the LED lamp, for it may damage
related parts of the vehicle.
License Plate Lamp Replacement
B0476KO01
1. Loosen the lens retaining screws with a cross-tip screwdriver.
2. Using a flat-blade screwdriver, gently pry the lens cover from the lamp
housing.
3. Remove the socket by turning it counterclockwise.
4. Remove the bulb by pulling it straight out.
5. Install a new bulb.
6. Reinstall in the reverse order.