heating HYUNDAI SANTA FE HYBRID 2022 Owners Manual

Foreword / Hybrid System Overview
1-46
Switching to Hybrid mode to allow
heating or air conditioning (Plug-in
hybrid vehicle)
OAEPHQ049842L
This message is displayed when the
vehicle automatically switches to
HEV mode to allow heating or air
conditioning. It is when the heating and
cooling system is on and the coolant
temperature is below 70 °C and ambient
temperature is below -15 °C.
If the coolant temperature gets higher
than 80°C or ambient temperature is
higher than -10°C or the driver turns
off the heating or cooling system, the
vehicle returns to its default (EV) mode. Maintaining Hybrid mode to allow
heating or air conditioning (Plug-in
hybrid vehicle)OAEPHQ049841L
This message is displayed when the
vehicle maintains the HEV mode to allow
heating or air conditioning. The mode
does not change when the driver presses
the [HEV] button to switch from the HEV
mode to EV mode while the heating and
cooling system is on and the coolant
temperature is below (70°C) and outdoor
temperature is below -15°C.
Low/High System Temp. Maintaining
Hybrid mode (Plug-in hybrid vehicle)
OAEPHQ049834LOAEPHQ049835L
This message is displayed when the
temperature of the high-voltage
(hybrid) battery is too low or too high.
This warning message is to protect the
battery and the hybrid system.

03
3-19
While the engine is running, push either
of the switches to warm the driver's seat
or front passenger's seat.
During mild weather or under conditions
where the operation of the seat warmer
is not needed, keep the switches in the OFF position.
[
Manual temperature control
Each time you push the switch, the
temperature setting of the seat is
changed as follows :

- Front seat
OFF
LOW ( )HIGH ( )
MIDDLE ( )
- Rear seat
OFF
Ÿ HIGH ( )
Ÿ LOW ( )

[ Automatic temperature control
The seat warmer starts to
automatically control the seat
temperature in order to prevent
low-temperature burns after being manually turned ON.

- Front seat
OFF
Ÿ

 

¡
¢0,1
0,1
LOW ( )+,*+
0,''/(
- Rear seat
OFF

Ÿ HIGH ( )
Ÿ LOW ( )30 MIN
If HIGH temperature is manually
selected again, the temperature will
be controlled automatically.
[
When pressing the switch for more
than 1.5 seconds with the seat warmer
operating, the seat warmer will turn
OFF.

[ The seat warmer defaults to the OFF
position whenever the ignition switch is ON.

[ Auto Comfort Control (for driver’s
seat) (if equipped)
- The seat warmer automatically controls the seat temperature
depending on the ambient
temperature and the set climate
control temperature when the
engine is running. If the seat
warmer switch is pushed, the seat
warmer will have to be controlled
manually.
To use this function, it must be
activated from the Settings menu in
the AV/AVN system screen.
- The seat warmer defaults to the OFF position whenever the ignition
switch is ON. However, if the Auto
Comfort Control function is ON, the
driver’s seat warmer will turn on
and off depending on the ambient
temperature and the set climate
control temperature.
For more details, refer to the separately
supplied Infotainment manual with
your vehicle.
Information
With the seat warmer switch in the ON position, the heating system in the seat
turns off or on automatically depending on
the seat temperature.

4
Check Turn Signal ................................................................................................... 4-27
Check Brake Light ................................................................................................... 4-27
Check Headlamp LED .............................................................................................4-28
Check Active Air Flap System .................................................................................4-28
Ready to Start Driving .............................................................................................4-28
Check Regenerative Brakes ....................................................................................4-28
Stop Vehicle and Check Brakes ..............................................................................4-28
Check Hybrid System ..............................................................................................4-28
Stop Safely and Check Hybrid System ...................................................................4-28
Check Hybrid System. Do Not Start Engine ...........................................................4-28
Stop Safely and Check Power Supply.....................................................................4-29
Check Virtual Engine Sound System ......................................................................4-29
Refill Inverter Coolant ..............................................................................................4-29
Park With Engine On to Charge Battery .................................................................4-29
Start Engine to Avoid Battery Discharge ................................................................4-29
Check Regenerative Brakes ...................................................................................... 4-30 Check Virtual Engine Sound System ..................................................................... 4-30
Unplug Vehicle to start (Plug-in Hybrid Vehicle) .................................................. 4-30
Remaining Time (Plug-in Hybrid Vehicle) ............................................................. 4-30
Wait Until Fuel Door Unlocks (Plug-in Hybrid Vehicle) ......................................... 4-31
Check Fuel Door (Plug-in Hybrid Vehicle).............................................................. 4-31
Fuel Door Unlocked (Plug-in Hybrid Vehicle) ........................................................ 4-32
Shift to P to Charge (Plug-in Hybrid Vehicle) ......................................................... 4-32
Switching to Hybrid Mode to Allow Heating or Air Conditioning
(Plug-in Hybrid Vehicle) .......................................................................................... 4-32
Maintaining Hybrid Mode to Allow Heating or Air Conditioning
(Plug-in Hybrid Vehicle) ..........................................................................................4-33
Low/High System Temp. Maintaining Hybrid Mode (Plug-in Hybrid Vehicle) ....4-33
Low/High System Temp. Switching To Hybrid Mode (Plug-in Hybrid Vehicle) ...4-33
Switching to Hybrid Mode to Lubricate Engine (Plug-in Hybrid Vehicle) ............4-34
Maintaining Hybrid Mode to Protect Engine (Plug-in Hybrid Vehicle) ................4-34
Exit Sport Mode to Switch to EV (Plug-in Hybrid Vehicle) ....................................4-34
LCD Display ..................................................................................................... 4-35 LCD Display Control ................................................................................................... 4-35
View Modes ................................................................................................................4-36Driving Assist Mode ................................................................................................. 4-37
Trip Computer Mode ............................................................................................... 4-37
Turn By Turn (TBT) Mode ......................................................................................... 4-37

Instrument Cluster
4-28
Wiper/Lights display
„Wiper„Lights
OIK047146LOIK047145L

[ This indicator displays which wiper
speed is selected using the wiper
control.

[ This indicator displays which exterior
light is selected using the lighting
control.
You can activate or deactivate Wiper/
Lights display function from the User
Settings menu in the cluster LCD display. - 6HWXS
Ÿ8VHUVHWWLQJV
Ÿ&OXVWHU
Ÿ
Wiper/Lights display
Low washer fluid (if equipped)
This message is displayed if the washer
fluid level in the reservoir is nearly empty.
Have the washer fluid reservoir refilled.
Low fuel
This message is displayed if the fuel tank
is almost out of fuel.
When this message is displayed, the low
fuel level warning light in the cluster will come on.
It is recommended to look for the nearest
fueling station and refuel as soon as possible.
NOTICE
Do not drive the vehicle with low fuel.
Hybrid battery damage may occur
when the fuel tank is completely empty.
Engine has overheated
This message is displayed when the
engine coolant temperature is above
120°C (248°F). This means that the
engine is overheated and may be damaged.
If your vehicle is overheated, refer to
“Overheating” section in chapter 8.
Check exhaust system (if equipped)
This message is displayed if there is
a problem with the GPF system. At
this time, the GPF warning light will
also blink. If this occurs, you have the
GPF system checked by an authorized
HYUNDAI dealer.
GPF : Gasoline Particulate Filter
Check headlight (if equipped)
This message is displayed if the
headlights are not operating properly. A
headlight bulb may need to be replaced.
Make sure to replace the burned out
bulb with a new one of the same wattage
rating. Check turn signal (if equipped)
This message is displayed if the turn
signal lamps are not operating properly.
A lamp may need to be replaced.
Make sure to replace the burned out
bulb with a new one of the same wattage
rating.
Check brake light (if equipped)
This message is displayed if the stop
lamps are not operating properly. A lamp
may need to be replaced.
Make sure to replace the burned out
bulb with a new one of the same wattage
rating.
NOTICE
Do not drive the vehicle with low fuel.
Hybrid battery damage may occur
when the fuel tank is completely empty.

04
4-33
Fuel door unlocked (Plug-in hybrid
vehicle)
OTMPHQ010033L
The message is displayed when the fuel
filler door unlocked. Also means “Ready
to refuel”. Please press the rear center
edge of fuel filler door to open.
Shift to P to charge (Plug-in hybrid
vehicle)
OAEPHQ049833L
This message is displayed when the
charging connector is plugged with the
shift lever in R (Reverse), N (Neutral) or
D (Drive). Move the shift lever to P (Park)
and re-start the charging process. Switching to Hybrid mode to allow
heating or air conditioning (Plug-in
hybrid vehicle)
OAEPHQ049842L
This message is displayed when the
vehicle automatically switches to
HEV mode to allow heating or air
conditioning. It is when the coolant
temperature is low (below -14°C) and the
driver turns on the heating or cooling
system.
If the coolant temperature gets higher
than -14°C or the driver turns off the
heating or cooling system the vehicle
returns to its default (EV) mode.

Instrument Cluster
4-34
Maintaining Hybrid mode to allow
heating or air conditioning (Plug-in
hybrid vehicle)
OAEPHQ049841L
This message is displayed when the
vehicle maintains the HEV mode to allow
heating or air conditioning. The mode
does not change when the driver presses
the [HEV] button to switch from the HEV
mode to EV mode while the heating and
cooling system is on and the coolant
temperature is below -14°C. Low/High System Temp. Maintaining
Hybrid mode (Plug-in hybrid vehicle)OAEPHQ049834LOAEPHQ049835L
This message is displayed when the
temperature of the high-voltage
(hybrid) battery is too low or too high.
This warning message is to protect the
battery and the hybrid system.
Low/High System Temp. Switching
to Hybrid mode (Plug-in hybrid
vehicle)
OAEPHQ049836LOAEPHQ049837L
This message is displayed when the
temperature of the high-voltage (hybrid)
battery is too low or high. This warning
message is to protect the battery and the
hybrid system.

Instrument Cluster
4-40
Engine coolant temperature
OTMH040007
This engine coolant temperature gauge
display shows the temperature of the
engine coolant when the engine is running.
NOTICE
When the gauge indicator gets out of
the normal range, toward the "H(Hot)"
position, it indicates overheating of the
engine. It may damage the engine.
Do not continue driving with the
overheated engine.
For more details, refer to "If the Engine
Overheats" section in the chapter 8.
User settings mode
OTM040060L
In this mode, you can change the
settings of the instrument cluster, doors,
lamps, etc.
1. Driver Assistance
2. Eco vehicle
3. Head-up display 4. Cluster5. Lights6. Door
7. Convenience8. Units
The information provided may differ
depending on which functions are
applicable to your vehicle.
Shift to P to edit settings
This warning message appears if you try
to adjust the User Settings while driving.
For your safety, change the User Settings
after parking the vehicle, applying the
parking brake and pressing the P (Park)
button.
Quick guide help
This mode provides quick guides for the
systems in the User Settings mode.
Select an item, press and hold the OK
button.
For more details, about each system,
refer to this Owner’s Manual.
Information
When the infotainment system is applied,
only the User’s Setting mode on the infotainment system is supported but the
User’s Setting mode on the instrument
cluster is not supported.

5
Head-Up Display (HUD).................................................................................. 5-66Head-Up Display Settings ........................................................................................ 5-66
Head-Up Display Information .................................................................................. 5-66
Precautions While Using The Head-Up Display ....................................................... 5-67
Lighting ............................................................................................................ 5-68 Exterior Lights ........................................................................................................... 5-68
High Beam Assist (HBA) ................................................................................. 5-72 High Beam Assist Settings ......................................................................................... 5-72
High Beam Assist Operation ...................................................................................... 5-73
High Beam Assist Malfunction And Limitations ....................................................... 5-73
Interior Lights ...................................................................................................5-75 Interior Lamp Auto Cut .............................................................................................. 5-75
Front Lamps ................................................................................................................ 5-75
Rear Lamps ................................................................................................................. 5-76
Vanity Mirror Lamp ..................................................................................................... 5-76
Luggage Compartment Lamp ................................................................................... 5-76
Puddle Lamp ............................................................................................................... 5-77
Welcome System ........................................................................................................ 5-77
Wipers And Washers ........................................................................................5-79 Windshield Wipers ..................................................................................................... 5-79
Front Windshield Washers ......................................................................................... 5-81
Rear Window Wiper And Washer .............................................................................. 5-81
Automatic Climate Control System ............................................................... 5-82 Automatic Heating And Air Conditioning .................................................................5-83
Manual Heating And Air Conditioning ......................................................................5-83
System Operation ...................................................................................................... 5-88
System Maintenance ................................................................................................ 5-90
Windshield defrosting and defogging ........................................................... 5-92 Automatic Climate Control System...........................................................................5-92
Auto Defogging System (Only for Automatic Climate Control System) .................5-93
Rear Window Defroster............................................................................................. 5-94

Convenience Features
5-54
Automatic reverse
OTMPH051008N
During power opening or closing if the
power tailgate senses any obstacle, the
power tailgate will stop and move in the
opposite direction.
The auto reverse function may not work
if objects are too soft or thin, or if the
tailgate is almost fully closed near the
latched position.
Caution should be taken to prevent any
objects from obstructing the tailgate opening.
If the automatic reverse feature operates
more than two times while attempting
to open or close the tailgate, the power
tailgate may stop at that position.
WARNING
Never intentionally place any object
or part of your body in the path of
the power tailgate to make sure the
automatic reverse function operates.
NOTICE
Do not put heavy objects on the power
tailgate before you operate the power
tailgate. Additional weight may damage
the operation of the system. Non-operating conditions of the
power tailgate
[
The power tailgate does not open
when the vehicle is in motion.
The chime will sound if you drive with
the tailgate opened. Stop your vehicle
immediately at a safe place and check
if your tailgate is opened.

[ Operating the power tailgate more
than 5 times continuously could
cause damage to the operating motor.
If this occurs, the power tailgate
system enters into thermal protection
mode to prevent the motor from
overheating. In thermal protection
mode, the power tailgate will not
operate. If any of the power tailgate
buttons are pressed to try to open the
tailgate, the chime will sound 3 times
but the tailgate will not operate.
Allow the power tailgate system
to cool for about 1 minute before
operating the system again.

05
5-83
Automatic Heating and Air Conditioning
The Automatic Climate Control System
is controlled by setting the desired
temperature.
1. Press the AUTO button. (3)The modes, fan speeds, air intake and
air-conditioning will be controlled
automatically by the temperature
setting you select.
2. Turn the temperature control knob (1, 2) to the desired temperature. If
the temperature is set to the lowest
setting (Lo), the air conditioning
system will operate continuously.
After the interior has cooled
sufficiently, adjust the knob to
a higher temperature set point
whenever possible.
To turn the automatic operation off,
select any button of the following: - Mode selection button
- Front windshield defroster button
(Press the button one more time
to deselect the front windshield
defroster function. The ‘AUTO’ sign
will illuminate on the information
display once again.)
- Fan speed control button
The selected function will be
controlled manually while other
functions operate automatically.
For your convenience and to improve
the effectiveness of the climate control,
use the AUTO button and set the
temperature to 22°C (72°F).
OTM050052
Information
Never place anything near the sensor to
ensure better control of the heating and cooling system.
Manual Heating and Air Conditioning
The heating and cooling system can be
controlled manually by pushing buttons
other than the AUTO button. In this case,
the system works sequentially according
to the order of buttons selected. When
pressing any button except the AUTO
button while using automatic operation,
the functions not selected will be
controlled automatically.
1. Start the engine.
2. Set the mode to the desired position. For improving the effectiveness of
heating and cooling, select:
- Heating:
- Cooling:
3. Set the temperature control to the desired position.
4. Set the air intake control to the outside (fresh) air position.
5. Set the fan speed control to the desired speed.
6. If air conditioning is desired, turn the air conditioning system on.
7. Press the AUTO button to convert to full automatic control of the system.