tow HYUNDAI VENUE 2023 Owner's Manual

06
6-7
Key Ignition Switch Positions
Switch
Position Action Notice
LOCK T
o turn the ignition switch to the
LOCK position, put the key in at
the ACC position and turn the key
towards the LOCK position.
The ignition key can be removed in
the LOCK position.
(The shift lever must be in the P
(Park) position for intelligent variable
transmission)
ACC Electrical accessories are usable.
The steering wheel unlocks.
ON This is the normal key position when
the engine has started.
All features and accessories are
usable.
The warning lights can be checked
when you turn the ignition switch
from ACC to ON. Do not leave the ignition switch in
the ON position when the engine is
not running in order to prevent the
battery from discharging.
START To start the engine, turn the ignition
switch to the START position. The
switch returns to the ON position
when you let go of the key. The engine will crank until you
release the key.

While Driving6-8
Starting the Engine
WARNING
Always wear appropriate shoes when
operating your vehicle.
Unsuitable shoes, such as high heels,
ski boots, sandals, flip-flops, etc., may
interfere with your ability to use the
brake and accelerator pedals.
Vehicle with manual transmission:
1. Make sure the parking brake is applied.
2. Make sure the shift lever is in neutral.
3. Depress the clutch and brake pedals.
4. Turn the ignition switch to the START position. Hold the key (maximum of
10 seconds) until the engine starts and
release it.
Information
Depress the brake pedal and clutch pedal
until the engine starts.
Vehicle with intelligent variable
transmission:
1. Make sure the parking brake is applied.
2. Make sure the shift lever is in P (Park).
3. Depress the brake pedal.
4. Turn the ignition switch to the START position. Hold the key (maximum of
10 seconds) until the engine starts and
release it.
Information

[It is best to maintain a moderate engine
speed until the vehicle engine comes
up to normal operating temperature.
Avoid harsh or abrupt acceleration or
deceleration while the engine is still
cold.

[ Whether the engine is cold or warm,
always start the vehicle with your foot
on the brake pedal. Do not depress the
accelerator while starting the vehicle.
Do not rev the engine while warming
it up.
NOTICE
To prevent damage to the vehicle:

[Do not hold the ignition key in the
START position for more than 10
seconds. Wait 5 to 10 seconds before
trying again.

[ Do not push or tow your vehicle to
start the engine.

06
6-11
Starting the Engine
WARNING

[Always wear appropriate shoes when
operating your vehicle.
Unsuitable shoes, such as high heels,
ski boots, sandals, flip-flops, etc.,
may interfere with your ability to use
the brake and accelerator pedals.

[ Do not start the vehicle with the
accelerator pedal depressed. The
vehicle can move and lead to an
accident.

[ Wait until the engine rpm is normal.
The vehicle may suddenly move if
the brake pedal is released when the
rpm is high.
Information

[The engine will start by pressing the
Engine Start/Stop button, only when
the smart key is in the vehicle.

[ Even if the smart key is in the vehicle,
if it is far away from the driver, the
engine may not start.

[ When the Engine Start/Stop button
is in the ACC or ON position, if any
door is open, the system checks for the
smart key. If the smart key is not in the
vehicle, the “
” indicator will blink
and the warning "Key not in vehicle"
will come on and if all doors are closed,
the chime will also sound for about
5 seconds. Keep the smart key in the
vehicle when using the ACC position or
if the vehicle engine is ON.
Vehicle with manual transmission:
1. Always carry the smart key with you.
2. Make sure the parking brake is applied.
3. Make sure the shift lever is in neutral.
4. Depress the clutch and brake pedals.
5. Press the Engine Start/Stop button.
Information
Depress the brake pedal and clutch pedal
until the engine starts.
Vehicle with intelligent variable
transmission:
1. Always carry the smart key with you.
2. Make sure the parking brake is applied.
3. Make sure the shift lever is in P (Park).
4. Depress the brake pedal.
5. Press the Engine Start/Stop button.
Information

[ Do not wait for the engine to warm up
while the vehicle remains stationary.
Start driving at moderate engine
speeds. (Aggressive accelerating and
decelerating should be avoided.)

[ Always start the vehicle with your foot
on the brake pedal. Do not depress the
accelerator while starting the vehicle.
Do not rev the engine while warming
it up.
NOTICE
To prevent damage to the vehicle:

[If the engine stalls while you are in
motion, do not attempt to move the
shift lever to the P (Park) position.
If traffic and road conditions permit,
you may put the shift lever in the N
(Neutral) position while the vehicle
is still moving and press the Engine
Start/Stop button in an attempt to
restart the engine.

[ Do not push or tow your vehicle to
start the engine.

While Driving6-54
Also, in certain instances the front
view camera recognition system
may not detect the vehicle ahead.
FCA system may not activate and
the warning message will not be
displayed.

[ If there is a malfunction with FCA
system, the Forward Collision
avoidance assist system is not
applied even though the braking
system is operating normally.

[ If the vehicle in front stops suddenly,
you may have less control of the
brake system. Therefore, always keep
a safe distance between your vehicle
and the vehicle in front of you.

[ FCA system may activate during
braking and the vehicle may stop
suddenly shifting loose objects
toward the passengers. Always keep
loose objects secured.

[ FCA system may not activate if the
driver applies the brake pedal to
avoid a collision.

[ The brake control may be
insufficient, possibly causing a
collision, if a vehicle in front abruptly
stops. Always pay extreme caution.

[ Occupants may get injured, if the
vehicle abruptly stops by activated
FCA system. Pay extreme caution.

[ Even if there is any problem in FCA
system's brake control function,
general braking performance will
operate normally. In this case,
the brake control function which
operates when the collision is
imminent will not activate. WARNING

[FCA system operates only to detect
vehicles in front of the vehicle.

[ FCA system does not operate when
the vehicle is in reverse.

[ FCA system is not designed to detect
other objects on the road such as
animals.

[ FCA system does not detect vehicles
in the opposite lane.

[ FCA system does not detect cross
traffic vehicles that are approaching.

[ FCA system cannot detect the
driver approaching the side view of
a parked vehicle (for example on a
dead end street.)
In these cases, you must maintain a
safe braking distance, and if necessary,
depress the brake pedal to reduce the
driving speed in order to maintain a
safe distance.
Limitations of the System
Forward Collision-Avoidance Assist
system is designed to monitor the
vehicle ahead in the roadway through
camera recognition to warn the driver
that a collision is imminent, and if
necessary, apply emergency braking.
In certain situations, the camera may
not be able to detect the vehicle ahead.
In these cases, FCA system may not
operate normally. The driver must
pay careful attention in the following
situations where FCA operation may be
limited.

06
6-55
Detecting Vehicles
The sensor may be limited when:

[The camera is blocked with a foreign
object or debris

[ The camera lens is contaminated due
to tinted, filmed or coated windshield,
damaged glass, or stuck of foreign
matter (sticker, bug, etc.) on the glass

[ Inclement weather such as heavy rain
or snow obscures the field of view of
the camera

[ The camera sensor recognition is
limited

[ The camera does not recognize the
entire vehicle in front.

[ The camera is damaged.

[ It is dark outside such as when the
headlamps are not on at night or the
vehicle is going through a tunnel.

[ There is a shadow is on the road by a
median strip, trees, etc.

[ The vehicle drives through a tollgate.

[ The rear part of the vehicle in front is
not normally visible. (the vehicle turns
in other direction or the vehicle is
overturned.)

[ The vehicle in front is too small to be
detected (for example a motorcycle or
a bicycle, etc.)

[ The vehicle in front is an oversized
vehicle or trailer that is too big to be
detected by the camera recognition
system (for example a tractor trailer,
etc.)

[ The camera's field of view is not well
illuminated (either too dark or too
much reflection or too much backlight
that obscures the field of view)
[
The vehicle in front does not have
their rear lights properly turned ON or
their rear lights are unusually located.

[ The outside brightness changes
suddenly, for example when entering
or exiting a tunnel

[ When light coming from a street light
or an oncoming vehicle is reflected on
a wet road surface such as a puddle in
the road

[ The field of view in front is obstructed
by sun glare

[ The windshield glass is fogged up; a
clear view of the road is obstructed

[ The vehicle in front is driving
erratically

[ The vehicle is on unpaved or uneven
rough surfaces, or road with sudden
gradient changes.

[ The vehicle drives inside a building,
such as a basement parking lot

[ The adverse road conditions cause
excessive vehicle vibrations while
driving

[ The sensor recognition changes
suddenly when passing over a speed
bump

[ The vehicle in front is moving
vertically to the driving direction

[ The vehicle in front is stopped
vertically

[ The vehicle in front is driving towards
your vehicle or reversing

[ You are on a roundabout and the
vehicle in front circles

06
6-65
System Malfunction
OQX069053L
Check Forward Collision-Avoidance Assist
system

[When F
CA is not working properly,
FCA warning light () will illuminate
and the warning message will appear
for a few seconds. After the message
disappears, the master warning light
(
) will illuminate. In this case, have
the vehicle inspected by an authorized
HYUNDAI dealer.

[ FCA warning message may appear
along with the illumination of the ESC
(Electronic Stability Control) warning
light.
WARNING

[FCA is only a supplemental system
for the driver’s convenience. The
driver should hold the responsibility
to control the vehicle operation. Do
not solely depend on the FCA system.
Rather, maintain a safe braking
distance, and, if necessary, depress
the brake pedal to reduce the driving
speed.

[ In certain instances and under
certain driving conditions, FCA
system may activate prematurely.
This initial warning message appears
on the LCD display with a warning
chime.
Also, in certain instances the front
radar sensor or camera recognition
system may not detect the vehicle
or pedestrian ahead. FCA system
may not activate and the warning
message will not be displayed.

[ If there is a malfunction with FCA
system, the Forward Collision
avoidance assist system is not
applied even though the braking
system is operating normally.

[ If the vehicle in front stops suddenly,
you may have less control of the
brake system. Therefore, always keep
a safe distance between your vehicle
and the vehicle in front of you.

[ FCA system may activate during
braking and the vehicle may stop
suddenly shifting loose objects
toward the passengers. Always keep
loose objects secured.

06
6-67

[The driver's field of view is not well
illuminated (either too dark or too
much reflection or too much backlight
that obscures the field of view)

[ The vehicle in front does not have
their rear lights properly turned ON

[ The outside brightness changes
suddenly, for example when entering
or exiting a tunnel

[ Light coming from a street light or an
oncoming vehicle is reflected on a wet
road surface such as a puddle in the
road

[ The field of view in front is obstructed
by sun glare

[ The windshield glass is fogged up; a
clear view of the road is obstructed

[ The vehicle in front is driving
erratically

[ The vehicle drives through a
construction area, on an unpaved
road, or above metal materials, such
as a railway

[ The vehicle drives inside a building,
such as a basement parking lot

[ The adverse road conditions cause
excessive vehicle vibrations while
driving

[ The vehicle in front is moving
vertically to the driving direction

[ The vehicle in front is stopped
vertically

[ The vehicle in front is driving towards
your vehicle or reversing
OQX069051

[Driving on a curve
The performance of FCA system may
be limited when driving on a curved
road.
In certain instances on a curved road,
FCA system may activate prematurely.
Also, in certain instances the front
radar sensor or camera recognition
system may not detect the vehicle
traveling on a curved road.
In these cases, the driver must
maintain a safe braking distance, and
if necessary, depress the brake pedal
to reduce your driving speed in order
to maintain a safe distance.

While Driving6-70
Detecting Pedestrians (if equipped)
The sensor may be limited when:

[ The pedestrian is not fully detected
by the camera recognition system, for
example, if the pedestrian is leaning
over or is not fully walking upright

[ The pedestrian is moving very quickly
or appears abruptly in the camera
detection area

[ The pedestrian is wearing clothing
that easily blends into the
background, making it difficult to be
detected by the camera recognition
system

[ The outside lighting is too bright (e.g.
when driving in bright sunlight or
in sun glare) or too dark (e.g. when
driving on a dark rural road at night)

[ It is difficult to detect and distinguish
the pedestrian from other objects in
the surroundings, for example, when
there is a group of pedestrians or a
large crowd

[ There is an item similar to a person's
body structure

[ The pedestrian is small

[ The pedestrian has impaired mobility

[ The sensor recognition is limited

[ The radar sensor or camera is blocked
with a foreign object or debris

[ Inclement weather such as heavy rain
or snow obscures the field of view of
the radar sensor or camera

[ When light coming from a street light
or an oncoming vehicle is reflected on
a wet road surface such as a puddle in
the road

[ The field of view in front is obstructed
by sun glare

[ The windshield glass is fogged up; a
clear view of the road is obstructed

[ The adverse road conditions cause
excessive vehicle vibrations while
driving Information
In some instances, FCA system
may be canceled when subjected to
electromagnetic interference.
Information
This device complies with Part 15 of the
FCC rules.
Operation is subject to the following two
conditions:
1. This device may not cause harmful
interference.
2. This device must accept any
interference received, including
interference that may cause undesired
operation.
WARNING

[Do not use Forward Collision-
avoidance Assist (FCA) system when
towing a vehicle. Application of
the FCA system while towing may
adversely affect the safety of your
vehicle or the towing vehicle.

[ Use extreme caution when the
vehicle in front of you has cargo that
extends rearward from the cab, or
when the vehicle in front of you has
higher ground clearance.

[ FCA system is designed to help
detect and monitor the vehicle
ahead or detect a pedestrian in
the roadway through radar signals
and camera recognition. It is
not designed to detect bicycles,
motorcycles, or smaller wheeled
objects such as luggage bags,
shopping carts, or strollers.

[ Never try to test the operation of FCA
system. Doing so may cause severe
injury or death.

While Driving6-72

[ Do not remove or damage the related
parts of LKA system.

[ You may not hear a warning sound
of LKA system because of excessive
audio sound.

[ Do not place objects on the
dashboard that reflects light such as
mirrors, white paper, etc. The system
may malfunction if the sunlight is
reflected.

[ Always have your hands on the
steering wheel while LKA system is
activated. If you continue to drive
with your hands off the steering
wheel after the "Keep hands on
steering wheel" warning message
appears, the system will turn off
automatically.

[ The steering wheel is not
continuously controlled so if the
vehicle speed is at a higher speed
when leaving a lane the vehicle
may not be able to be controlled by
the system. The driver must always
follow the speed limit when using
the system.

[ If you attach objects to the steering
wheel, the system may not assist
steering or the hands off alarm may
not work properly. When you tow a
trailer, make sure that you turn off
LKA system.LKA System Operation
OQX069024L
To activate/deactivate LKA system:
With the ignition switch in the ON
position, press LKA system button
located on the instrument panel on the
left hand side of the steering wheel.
The indicator in the cluster display will
initially illuminate white. This indicates
LKA system is in the READY but NOT
ENABLED state.
The color of indicator will
change depending on the
condition of LKA system.
- White: Sensor does not detect lane lines or vehicle speed is under 40
MPH (64 km/h).
- Green: Sensor detects lane lines and the system is able to control vehicle
steering.

06
6-85
63(&,$/'5,9,1*&21',7,216
Hazardous Driving Conditions
When hazardous driving elements
are encountered such as water, snow,
ice, mud and sand, take the below
suggestions:

[Drive cautiously and keep a longer
braking distance.

[ Avoid abrupt braking or steering.

[ When your vehicle is stuck in
snow, mud, or sand, use second
gear. Accelerate slowly to avoid
unnecessary wheel spin.

[ Put sand, rock salt, tire chains or other
non-slip materials under the wheels to
provide additional traction while the
vehicle becomes stuck in ice, snow,
or mud.
WARNING
Downshifting with an intelligent
variable transmission while driving on
slippery surfaces can cause an accident.
The sudden change in tire speed could
cause the tires to skid. Be careful when
downshifting on slippery surfaces.
Rocking the Vehicle
If it is necessary to rock the vehicle to
free it from snow, sand, or mud, first turn
the steering wheel right and left to clear
the area around your front wheels. Then,
shift back and forth between R (Reverse)
and a forward gear.
Try to avoid spinning the wheels, and do
not race the engine.
To prevent transmission wear, wait until
the wheels stop spinning before shifting
gears. Release the accelerator pedal
while shifting, and press lightly on the
accelerator pedal while the transmission
is in gear. Slowly spinning the wheels in
forward and reverse directions causes a
rocking motion that may free the vehicle.
WARNING
If the vehicle is stuck and excessive
wheel spin occurs, the temperature
of the tires can increase very quickly.
If the tires become damaged, a tire
blow out or tire explosion can occur.
This condition is dangerous - you and
others may be injured. Do not attempt
this procedure if people or objects are
anywhere near the vehicle.
If you attempt to free the vehicle, the
vehicle can overheat quickly, possibly
causing an engine compartment fire
or other damage. Try to avoid spinning
the wheels as much as possible to
prevent overheating of either the tires
or the engine. DO NOT allow the vehicle
to spin the wheels above 35 MPH (56
km/h).
Information
The ESC system must be turned OFF
before rocking the vehicle.
NOTICE
If you are still stuck after rocking the
vehicle a few times, have the vehicle
pulled out by a tow vehicle to avoid
engine overheating, possible damage to
the transmission, and tire damage. See
"Towing" in chapter 7.