display INFINITI FX35 2004 User Guide

TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
ACS-33
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
ACTIVE TEST
Caution

Do not perform the active test while driving.

Active test cannot be started while ICC system warning indicator illuminates.
1. Touch “ACTIVE TEST” on selection screenACS-30, "
CONSULT-II INSPECTION PROCEDURE" .
2. Touch any of “ICC BUZZER 1”, “METER LAMP”, “STOP LAMP”
and “BOOSTER SOL/V 3” on selection screen.
3. Touch necessary item and “START”.
4. Active test screen will be shown.
IDLE SW
[ON/OFF]××Indicates [ON/OFF] status of idle switch read by ICC unit
via CAN communication (ECM transmits ON/OFF status
via CAN communication).
GEAR
[1, 2, 3, 4, 5]××Indicates AT gear position read by ICC unit via CAN com-
munication (TCM transmits gear position via CAN commu-
nication).
BUZZER O/P
[ON/OFF] ×Indicates [ON/OFF] status of ICC war output.
ICC WARNING×NOTE:
This item is displayed, but cannot monitoring.
VHCL SPD AT
[km/h] or [mph]
×Indicates vehicle speed calculated from AT vehicle speed
sensor by ICC unit via CAN communication (TCM trans-
mits AT vehicle speed sensor signal via CAN communica-
tion).
PRESS SENS
[bar]×××Indicates brake fluid pressure value calculated from signal
voltage of pressure sensor.
PRESS SENS 2×NOTE:
This item is displayed, but cannot monitoring.
D RANGE SW
[ON/OFF]××Indicates [ON/OFF] status of “D” position read by ICC unit
via CAN communication (TCM transmits ON/OFF condi-
tion of “D” position via CAN communication).
AT OD OFF
[ON/OFF]×Indicates [ON/OFF] status of OD cancel output under con-
trol.
NP RANGE SW
[ON/OFF]××Indicates PNP switch signal read by ICC unit via CAN
communication. TCM transmits PNP switch signal via CAN
communication.
DISTANCE×NOTE:
This item is displayed, but cannot monitoring.
RELATIVE SPD×NOTE:
This item is displayed, but cannot monitoring.
STP LMP DRIVE
[ON/OFF]××Indicates [ON/OFF] status of brake hold relay drive output. Monitored Item [unit]MAIN SIG-
NALSECU
INPUT
SIGNALSSELEC-
TION
FROM
MENUDescription
SKIA6195E

TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
ACS-35
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
METER LAMP

Start engine.

Touch “ON” and “OFF” to check that ICC system display oper-
ates as in the following chart.
STOP LAMP

Touch “ON” and “OFF” to check that stop lamp operates as in
the following chart.
BOOSTER SOL/V 3

Touch any of “MODE 1”, “MODE 2”, “MODE 3” to check that fol-
lowing operation condition is caused by operating monitor and
brake pedal.

“START” is displayed 10 seconds after operation start. (Active
test is completed.)
Self-Diagnostic FunctionAKS006YV
WITH CONSULT-II
1. Go to operation check after asking the customer for symptom information. Refer to ACS-9, "ACTION
TEST" .
2. Stop vehicle, turn ignition switch OFF, then connect CONSULT-II and CONSULT-II CONVERTER to data
link connector.
3. With engine started, touch “START”, “ICC”, “SELF-DIAG RESULTS” on CONSULT-II screen in this order.
METER LAMP ON OFF
ICC system display Full illumination OFF
SKIA1231E
STP LMP DRIVE ON OFF
Stop lamp Lamp ON Lamp OFF
SKIA1232E
SKIA1233E
PKIA0363J

ACS-36
[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
Revision: 2004 November 2004 FX35/FX45
CAUTION:
If “ICC” cannot be shown after several attempts, the ICC unit may have had malfunction. Repair or
replace it. Refer to GI-40, "
CONSULT-II Data Link Connector (DLC) Circuit" .
4. Self-diagnostic result appears on screen. If “NO DTC ···” is shown, check ICC warning lamp. If any mal-
function is indicated, GO TO step 5.
5. According to ACS-40, "
Diagnostic Trouble Code (DTC) Chart" , perform appropriate check, and repair or
replace malfunctioning part as necessary.
6. Turn ignition switch OFF.
7. Start engine and touch “START”, “ICC”, “SELF-DIAG RESULT”, and “ERASE” on CONSULT-II display in
turn to erase the memory.
CAUTION:
If the memory does not erase, go to 5.
8. Perform ICC system running test (drive vehicle with ICC system ON), and make sure that ICC warning
lamp does not illuminate.
WITHOUT CONSULT-II
1. Go to operation check after asking the customer for symptom information. Refer to ACS-9, "ACTION
TEST" .
2. Stop the vehicle to start the self-diagnosis.
3. Turn ignition switch OFF.
4. Turn ignition switch ON, and within 5 to 10 seconds, press
ACCEL/RES switch 5 times. Then press COAST/SET switch 5
times to start self-diagnosis.
CAUTION:

Do not start the engine.

Do not turn the ON/OFF switch ON.

When operation above is not completed within 5 to 10 sec-
onds, start again from above go to 3.

If self-diagnosis mode cannot be started after several
attempts, the ICC unit may have had malfunction. Repair or
replace it. Refer to ACS-37, "
SELF-DIAGNOSIS BY ICC SYS-
TEM DISPLAY WILL NOT RUN." .
5. When self-diagnosis mode is started, DTC are shown on set vehicle speed indicator.
CAUTION:

DTC will disappear after 5 minutes.
SKIA7067E
SKIA1236E

TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
ACS-37
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45

When more than one malfunctions are detected, a maximum of 3 code numbers can be stored;
the latest malfunction will be displayed first.
6. Check ACS-40, "
Diagnostic Trouble Code (DTC) Chart" , and repair or replace if necessary.
7. After repair, erase DTC stored in the ICC unit.
8. DTC 55 will be shown.
9. Turn ignition switch OFF to exit the diagnosis.
10. Perform ICC system running test (drive vehicle with ICC system ON), and make sure that ICC warning
lamp does not illuminate.
Self-Diagnostic Erasing Method
1. Stop the vehicle and turn the ignition switch OFF.
2. Turn ignition switch ON and start self-diagnosis.
3. During self-diagnosis mode, press CANCEL switch 5 times, and DISTANCE switch 5 times in this order.
CAUTION:

Press them within 10 seconds after pressing CANCEL switch at first.

When operation is not completed within 10 seconds, start again from above go to 2.
4. DTC 55 will be shown.
CAUTION:
DTC of an existing malfunction will not be erased.
5. Turn ignition switch OFF to exit the diagnosis.
6. Perform ICC system running test (drive vehicle with ICC system ON), and make sure that ICC system
warning lamp (yellow) does not illuminate.
SELF-DIAGNOSIS BY ICC SYSTEM DISPLAY WILL NOT RUN.
Possible Irregular Condition
SKIA7068E
Open or short lines Trouble phenomenon Malfunction causes
ICC unit power supply malfunction No voltage supply from ignition switch Fuse blown
Harness open
Harness shorted
Ground cable not connected Harness open
Harness shorted
ICC steering switch malfunction No signal transmitted Harness open
Harness shorted
Spiral cable open
Spiral cable shorted
Switch or ECM malfunction
CAN communication system malfunction Signal not transmitted Harness open
Harness shorted
CAN communication outside the stan-
dard.

ACS-38
[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
Revision: 2004 November 2004 FX35/FX45
1. CHECK ICC SYSTEM DISPLAY

When ignition switch is ON, do all displays illuminate?
YES or NO
YES >> GO TO 2.
NO >> GO TO 5.
2. CHECK ICC STEERING SWITCH

Check ICC steering switch. Refer to ACS-65, "ICC Steering Switch" .
OK or NG
OK >> GO TO 3.
NG >> Replace ICC steering switch.
3. CHECK HARNESS BETWEEN ECM AND ICC STEERING SWITCH

Check harness and spiral cable between ECM and ICC steering switch for open or short circuit.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness or spiral cable between ECM and ICC steering switch.
4. CHECK SELF-DIAGNOSIS

Disconnect connector of ECM, and check terminals for bend and looseness. Securely connect it again.

Enter self-diagnosis mode for ICC system?
YES or NO
YES >> INSPECTION END
NO >> GO TO 5.
5. CHECK POWER SUPPLY FOR ICC UNIT

Check ICC unit power supply, and repair if necessary.

When ignition switch is ON, do all displays illuminate?
YES or NO
YES >> Perform self-diagnosis again.
NO >> GO TO 6.
6. CHECK CONNECTOR FOR ICC UNIT

Disconnect connector of ICC unit, and check terminals for bend and looseness. Securely connect it again.

When ignition switch is ON, do all displays illuminate?
YES or NO
YES >> Perform self-diagnosis again.
NO >> GO TO 7.
Combination meter system malfunction Indication not possible Indicator malfunction
Indicator segments disappear.
ICC unit malfunctionOpen or short lines Trouble phenomenon Malfunction causes

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-41
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
DTC 11 CONTROL UNITAKS006YX
1. DIAGNOSTIC CHECK
1. Are any items other than “DTC 11 CONTROL UNIT” indicated on self-diagnosis display?
YES or NO
YES >> Repair or replace applicable item. Erase DTC and perform ICC system running test. Then perform
self-diagnosis of ICC system again.
NO >> Replace ICC unit. Erase DTC and perform ICC system running test. Then perform self-diagnosis
of ICC system again.
DTC 20 CAN COMM CIRCUITAKS006YY
1. CHECK CAN COMMUNICATION
With CONSULT-II
1. Perform self-diagnosis.
2. Print self-diagnostic result.
>> After printing self-diagnostic result, go to “CAN system”. Refer to LAN-4, "
Precautions When
Using CONSULT-II" .
90 STOP LAMP RLY FIX×× ×
Normally open terminal of stop
lamp relay is stuck.ACS-50
92 ECM CIRCUIT××××

ECM malfunction

Accelerator pedal position sensor
malfunction

ICC unit malfunctionACS-54
96 NP RANGE×××

Park/neutral position switch har-
ness is open or shorted.

Park/neutral position switch mal-
function.

TCM malfunctionACS-55
97 AT CIRCUIT×××
TCM malfunctionACS-56
98 GEAR POSITION×××

TCM malfunction

AT turbine revolution sensor mal-
function

AT vehicle speed sensor mal-
functionACS-56
102 RADAR STAIN×× ×
ICC sensor body window has
contamination.ACS-57
103 LASER SENSOR FAIL×× ×
ICC sensor internal malfunctionACS-58
104 LASER AIMING INCMP×× ×
Laser beam aiming of ICC sensor
is not adjusted.ACS-58
107 LASER COMM FAIL×× ×

CAN data received by ICC sen-
sor is strange (from ICC unit,
combination meter or ECM).ACS-58
109 LASER HIGH TEMP×× ×
Temperature around ICC sensor
is excessively high.ACS-58
DTC
No.CONSULT-II screen termsICC sys-
tem
warning
lampFail-safe
Malfunctions detected where...Refer-
ence
page Vehicle-
to-vehi-
cle dis-
tance
control
modeConven-
tional
(fixed
speed)
cruise
control
modeBrake
assist
(with pre-
view
function)

ACS-42
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: 2004 November 2004 FX35/FX45
DTC 31 POWER SUPPLY CIR, DTC 34 POWER SUPPLY CIR 2AKS006YZ
1. CHECK CONNECTOR ICC UNIT
1. Turn ignition switch OFF.
2. Disconnect ICC unit connector, and connect it securely again. Then erase DTC. After that perform self-
diagnosis of ICC system again.
OK or NG
OK >> GO TO 2.
NG >>

Poor connector connection.

Check connector. (Check connector housing for disconnected, loose, bent, and collapsed ter-
minals. If any malfunction is detected, repair applicable part.) After repair, erase DTC, and per-
form ICC running test. Then perform self-diagnosis of ICC system again.
2. CHECK POWER SUPPLY CIRCUIT FOR ICC UNIT
1. Turn ignition switch ON.
2. Check voltage between ICC unit harness connector M89 termi-
nal 33 (G/R), 42 (G/R) and ground.
OK or NG
OK >> GO TO 3.
NG >>

Repair ICC unit power supply harness.

After repair, erase DTC and perform ICC system run-
ning test. Then, perform self-diagnosis of ICC system
again.
3. CHECK GROUND CIRCUIT FOR ICC UNIT
1. Turn ignition switch OFF.
2. Disconnect ICC unit connector.
3. Check continuity between ICC unit harness connector M88 ter-
minal 19 (B), 20 (B), M89 terminal 46 (B) and ground.
OK or NG
OK >> After replacing ICC unit, erase DTC, and perform ICC
system running test. Then perform self-diagnosis of ICC
system again.
NG >>

Repair ICC unit ground harness.

After repair, erase DTC and perform ICC system running test. Then, perform self-diagnosis of
ICC system again.
DTC 41 VHCL SPEED SE CIRCAKS006Z0
1. PERFORM ICC UNIT SELF-DIAGNOSIS
1. Perform self-diagnosis. Is “DTC 43 ABS/TCS/VDC CIRC” or “DTC 20 CAN COMM CIRCUIT” indicated in
self-diagnosis item display?
YES or NO
YES >> Repair or replace applicable item. Erase DTC and perform ICC system running test. Then perform
self-diagnosis of ICC system again.
NO >> GO TO 2Battery voltage should exist.
SKIA1173E
Continuity should exist.
SKIA6650E

ACS-56
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: 2004 November 2004 FX35/FX45
4. CHECK SHIFT POSITION SIGNAL
With CONSULT-II

With TCM diagnosis, check that shift operates normally. Refer to AT- 11 2 , "DTC P0705 PARK/NEUTRAL
POSITION SWITCH" .
OK or NG
OK >>
Check harness between park/neutral position switch and smart entrance control unit.

After repair, erase DTC and perform ICC system running test. Then, perform self-diagnosis of
ICC system again.
NG >>

Perform TCM diagnosis.

After repair, erase DTC and perform ICC system running test. Then, perform self-diagnosis of
ICC system again.
DTC 97 AT CIRCUITAKS007IC
1. CHECK AT CIRCUIT
With CONSULT-II

With TCM diagnosis, check that shift operates normally. Refer to AT- 11 2 , "DTC P0705 PARK/NEUTRAL
POSITION SWITCH" .
OK or NG
OK >> Replace ICC unit. erase DTC and perform self-diagnosis of ICC system again.
NG >>

Perform TCM diagnosis.

After repair, erase DTC and perform self-diagnosis of ICC system again.
DTC 98 GEAR POSITIONAKS007ID
1. DIAGNOSTIC CHECK
With CONSULT-II

Is “DTC 43 ABS/TCS/VDC CIRC” or “DTC 41 VHCL SPEED SE CIRC” indicated in self-diagnosis display
item?
YES or NO
YES >> Repair or replace applicable item. Erase DTC and perform self-diagnosis of ICC system again.
NO >> GO TO 2.
2. CHECK VEHICLE SPEED SIGNAL
With CONSULT-II

With data monitor, check that “VHCL SPEED SE” is normal.
OK or NG
OK >> GO TO 3.
NG >> Replace ICC unit. Erase DTC and perform self-diagnosis of ICC system again.
3. CHECK SHIFT GEAR POSITION

Check that gear positions are correct in A/T.
OK or NG
OK >> GO TO 5.
NG >> GO TO 4.

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-57
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
4. CHECK TCM GEAR POSITION SIGNAL
With CONSULT-II

With TCM data monitor with CONSULT-II, check that gear positions are correct.
OK or NG
OK >> Replace ICC unit. Erase DTC and perform self-diagnosis of ICC system again.
NG >>

Perform TCM diagnosis.

After repair, erase DTC and perform self-diagnosis of ICC system again.
5. CHECK TCM TURBINE ROTATION
With CONSULT-II

With TCM diagnosis, check that turbine rpm is normal. Refer to AT- 1 4 3 , "DTC P1716 TURBINE REVOLU-
TION SENSOR" .
OK or NG
OK >> Replace ICC unit. Erase DTC and perform self-diagnosis of ICC system again.
NG >>

Perform TCM diagnosis.

After repair, erase DTC and perform self-diagnosis of ICC system again.
DTC 102 RADAR STAINAKS006ZI
1. VISUAL INSPECTION (1)

Check that there is no contamination and foreign material on ICC sensor body window.
OK or NG
OK >> GO TO 2.
NG >>

If any, remove them.

After that, erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC
system again.
2. VISUAL INSPECTION (2)

Check ICC sensor body window for cracks.
OK or NG
OK >> GO TO 3.
NG >>

Replace ICC sensor, and adjust laser beam.

After that, erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC
system again.
3. ASKING COMPLAINTS
1. Is there any trace of contamination or foreign material on ICC sensor?
2. Is there any possibility that vehicle was driven in snow or ICC sensor was frosted?
3. Is there any possibility that ICC sensor was fogged temporarily? (Front window glass may have also
tended to be fogged.)
Ye s o r N o
Yes >> Explain difference in displays between contamination detection result and current indication to
customer, and tell them “This is not malfunction”.
No >>

Replace ICC sensor, and adjust laser beam aiming.

After that, erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC
system again.

ACS-58
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: 2004 November 2004 FX35/FX45
DTC 103 LASER SENSOR FAILAKS006ZJ
1. DIAGNOSTIC CHECK

Are “DTC 11 CONTROL UNIT” or “DTC 20 CAN COMM CIRCUIT” item indicated in self-diagnosis display
item?
YES or NO
YES >> GO TO APPLICABLE ITEM INSPECTION. Refer to ACS-41, "DTC 11 CONTROL UNIT" , and
ACS-41, "
DTC 20 CAN COMM CIRCUIT" .
NO >>

Replace ICC sensor, and adjust laser beam aiming.

After that, erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC
system again.
DTC 104 LASER AIMING INCMPAKS006ZK
1. DIAGNOSTIC CHECK
1. Adjust laser beam aiming. Erase DTC and perform ICC system running test.
2. After that, perform self-diagnosis of ICC system. Is “DTC 104 LASER AIMING INCMP” indicated?
YES or NO
YES >>
Replace ICC sensor, and adjust laser beam aiming.

After that, erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC
system again.
NO >> INSPECTION END
DTC 107 LASER COMM FAILAKS006ZL
1. DIAGNOSTIC CHECK

Is “DTC 11 CONTROL UNIT” or “DTC 20 CAN COMM CIRCUIT” items other than “DTC 107 LASER
COMM FAIL” indicated in the self-diagnosis display item?
YES or NO
YES >> GO TO APPLICABLE ITEM INSPECTION. Refer to ACS-41, "DTC 11 CONTROL UNIT" , and
ACS-41, "
DTC 20 CAN COMM CIRCUIT" .
NO >>

Replace ICC sensor. Adjust laser beam aiming.

After that, erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC
system again.
DTC 109 LASER HIGH TEMPAKS006ZM
1. CHECK SYMPTOM

Is cooling system malfunctioning?
YES or NO
YES >>
Repair cooling system.

After that, erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC
system again.
NO >>

Replace ICC sensor, and adjust laser beam aiming.

After repair, erase DTC. Then perform ICC system running test, and perform self-diagnosis of
ICC unit.