shaft INFINITI FX35 2004 Service Manual

PR-8
REAR PROPELLER SHAFT
Revision: 2004 November 2004 FX35/FX45
REMOVAL
1. Move the A/T select lever to N position and release the parking brake.
2. Remove the tunnel stay with power tool. Refer to RSU-5, "
REAR
SUSPENSION ASSEMBLY" .
3. Remove the center muffler with power tool. Refer to EX-3,
"EXHAUST SYSTEM" for details.
4. Loosen the center bearing mounting bracket (lower) fixing nuts
with power tool.
5. Put matching marks on flange and rear propeller shaft.
CAUTION:
For matching mark, use paint. Never damage the propeller
shaft flange and companion flange on the rear final drive.
6. Remove the propeller shaft fixing bolts and nuts.
7. Remove the center bearing mounting bracket (lower) fixing nuts,
remove the propeller shaft from the vehicle.
INSPECTION
1. Inspect propeller shaft runout. If runout exceeds specifications,
replace propeller shaft assembly.
1. Propeller shaft (1st shaft) 2. Center bearing assembly 3.Center bearing mounting bracket
(lower)
4. Washer 5. Center flange 6. Propeller shaft (2nd shaft)
7. Lock nut 8. Clip 9.Center bearing mounting bracket
(upper)
SDIA1520E
SDIA1577E
SDIA1522E
Propeller shaft runout limit : 0.6 mm (0.024 in) or less
SPD106

REAR PROPELLER SHAFT
PR-9
C
E
F
G
H
I
J
K
L
MA
B
PR
Revision: 2004 November 2004 FX35/FX45
Propeller shaft runout measuring point (2WD models):
Unit: mm (in)
Propeller shaft runout measuring point (AWD models):
Unit: mm (in)
2. If the play exceeds specifications, replace propeller shaft
assembly. Distance A B C
A/T 192 (7.56) 190 (7.48) 185 (7.28)
SDIA1581E
Distance A B C
A/T 162 (6.38) 245 (9.65) 185 (7.28)
SDIA1779E
Journal axial play : 0 mm (0 in)
SPD874

PR-10
REAR PROPELLER SHAFT
Revision: 2004 November 2004 FX35/FX45
INSTALLATION
1. Paying attention to following items, install in the reverse order of removal.
a. Install the propeller shaft onto the rear final drive companion
flange while aligning the matching marks that are marked during
removal.
b. Adjust position of the bearing cushion so as not to apply thrust
play to the center bearing insulator.
c. Position the bearing cushion overlap as shown in the figure.
d. Install the center bearing bracket (upper) with its arrow mark fac-
ing forward.
e. Tighten the center bearing mounting bracket (upper) fixing nuts
to specified torque.
CAUTION:
Do not reuse the nuts. Always replace the nuts with a new
ones.
2. If companion flange has been removed, put new alignment
matching mark C on it. Then, reassemble using the following
procedure.
Perform these steps when either of final drive and propeller
shaft is replaced with a new one.
a. Erase original mark C from companion flange with suitable sol-
vent.
b. Measure companion flange vertical runout.
c. Determine the position where maximum runout is read on dial
gauge. Put mark (shown by C in figure) on flange perimeter cor-
responding to maximum runout position.
SDIA1522E
PDIA0017E
SDIA1780E

REAR PROPELLER SHAFT
PR-11
C
E
F
G
H
I
J
K
L
MA
B
PR
Revision: 2004 November 2004 FX35/FX45
3. If the propeller shaft or final drive has been replaced, connect
the propeller shaft and final drive as follows:
NOTE:
Avoid damaging the rebro joint boot, protect it with a shop towel
or equivalent.

Install the propeller shaft while aligning its matching mark A
with the mark C on the joint as close as possible.

Tighten the joint bolts/nuts to specified torque.
CAUTION:
Do not reuse the bolts, and washers. Always replace the
them with new ones.

After installation, check the vibration by driving the vehicle. If the vibration is present, remove the pro-
peller shaft from the final drive companion flange.

Turn the propeller shaft 60, 120, 180, 240 or 300 degrees and reinstall the propeller shaft to the com-
panion flange, then measure the runout again by driving the vehicle on each angle position.
Disassembly and AssemblyADS000KN
DISASSEMBLY
Center Bearing
NOTE:

The joint cannot be disassembled.

The center bearing can be disassembled.
1. Remove the propeller shaft assembly from the vehicle. Refer to PR-8, "
REMOVAL" .
2. Put matching marks on propeller shaft and center flange, then
disassemble the 1st and 2nd propeller shaft.
CAUTION:
For matching mark, use paint. Never damage the propeller
shaft flange and center flange.
3. Put matching marks onto the center flange and propeller shaft
end as shown.
4. Stake center flange lock nut with a punch (except 3F80A-
1VL107- type/VK45DE, AWD).
SDIA0768E
SDIA1538E
SDIA1539E

PR-12
REAR PROPELLER SHAFT
Revision: 2004 November 2004 FX35/FX45
5. Hold the center flange using a flange wrench, and remove the
lock nut.
6. Remove the center flange using a commercial available bearing
puller.
7. Press out the center bearing using a puller and hydraulic press.
ASSEMBLY
1. Apply multi-purpose grease to the each end of the center bear-
ing and each face of the washer.
2. For the 3S80A-1VL107 (VQ35DE/2WD) and 3F80A-1VL107
(VK45DE/AWD) type, install the center bearing with its “F” mark
facing the front of the vehicle.
For the 3F80A-1VL107(VQ35DE/AWD) type, install the center
bearing with its “F” mark facing the rear of the vehicle.
3. Install the washer.
4. Install the center flange onto the propeller shaft with aligning the
marks that are marked while removal.
5. Install and tighten the new lock nut to specified torque using a
torque wrench.
For the 3S80A-1VL107 (VQ35DE/2WD) and 3F80A-1VL107 (VQ35DE/AWD) type, tighten the lock nut to
specified torque.
6. For the 3S80A-1VL107 (VQ35DE/2WD) and 3F80A-1VL107
(VQ35DE/AWD) type, place a piece of wood under the center
flange, stake the lock nut against the propeller shaft groove.
CAUTION:
Do not use the lock nut. Always replace the lock nut with a
new one.
7. Temporality tighten the lock nut to the following torque.
Loosen the lock nut, then retighten it to specified torque.
For 3F80A-1VL107 (VK45DE/AWD) type, tighten the lock nut to
specified torque.
CAUTION:
Do not reuse the lock nut. Always replace the lock nut with
a new one.Tool number : KV40104000 ( – )
SDIA1540E
Tool number : ST30031000 (J22912-01)
SDIA1541E
SDIA1542E
SDIA1543E

REAR PROPELLER SHAFT
PR-13
C
E
F
G
H
I
J
K
L
MA
B
PR
Revision: 2004 November 2004 FX35/FX45
8. Assemble the 1st and 2nd shaft propeller shafts while aligning
the matching marks that are marked during removal.
9. Install and tighten the bolts/nuts and tighten them to specified
torque.
CAUTION:
Do not reuse the bolts, nuts and washers. Always replace
the them with new ones.
10. Recheck the tightening torque using a torque wrench.
11. Install the propeller shaft assembly. Refer to PR-10, "
INSTALLA-
TION" .SDIA1538E

PR-14
SERVICE DATA AND SPECIFICATIONS (SDS)
Revision: 2004 November 2004 FX35/FX45
SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
General SpecificationsADS000O9
2WD MODEL
AW D M OD E L
Front Propeller ShaftADS000OA
JOURNAL AXIAL PLAY
PROPELLER SHAFT RUNOUT LIMIT
Rear Propeller ShaftADS000OB
JOURNAL AXIAL PLAY
PROPELLER SHAFT RUNOUT LIMIT
Applied model VQ35DE
Propeller shaft model 3S80A-1VL107
Number of joints3
Coupling method with transmission Sleeve type
Applied model VQ35DE VK45DE
Front propeller shaftPropeller shaft model 2S56A
Number of joints 2
Coupling method with front final drive Flange type
Coupling method with transfer Sleeve type
Rear propeller shaftPropeller shaft model 3F80A-1VL107
Number of joints 3
Coupling method with transfer Flange type
Model2S56A
Yoke journal bearing axial play 0 mm (0 in)
Model2S56A
Propeller shaft runout limit 0.6 mm (0.024 in) or less
Model3S80A-1VL107, 3F80A-1VL107
Yoke journal bearing thrust play 0 mm (0 in)
Model3S80A-1VL107, 3F80A-1VL107
Propeller shaft runout limit 0.6 mm (0.024 in) or less

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
PS-7
C
D
E
F
H
I
J
K
L
MA
B
PS
Revision: 2004 November 2004 FX35/FX45
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTINGPFP:00003
NVH Troubleshooting ChartAGS000GS
Use chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×: ApplicableReference page
PS-8PS-8PS-25PS-25PS-25PS-8PS-10PS-10
EM-15
, EM-169PS-10PS-12PS-19PS-12PS-12PS-19
NVH in PR section
NVH in RFD section
NVH in FAX, RAX, FSU, RSU section
NVH in WT section
NVH in WT section
NVH in FAX section
NVH in BR section
Possible cause and suspected parts
Fluid level
Air in hydraulic system
Outer socket ball joint swinging force
Outer socket ball joint rotating torque
Outer socket ball joint end play
Steering fluid leakage
Steering wheel play
Steering gear rack sliding force
Drive belt looseness
Improper steering wheel
Improper installation or looseness of tilt lock lever
Mounting rubber deterioration
Steering column deformation or damage
Improper installation or looseness of steering column
Steering linkage looseness
PROPELLER SHAFT
DIFFERENTIAL
AXLE and SUSPENSION
TIRES
ROAD WHEEL
DRIVE SHAFT
BRAKES
Symptom STEERINGNoise× × ××××× × × ×××××× ×
Shake××× × ×××× ×
Vibration××××× × ×× ×
Shimmy××× × ××× ×
Judder××××××

PS-12
STEERING COLUMN
Revision: 2004 November 2004 FX35/FX45
STEERING COLUMNPFP:48810
Removal and InstallationAGS000GY
CAUTION:

Care must be taken not to give axial impact to steering column assembly during removal and
installation.

Care must be taken not to move steering gear during removal of steering column assembly.
REMOVAL
1. Set vehicle to the straight ahead-direction.
2. Remove driver air bag module from steering wheel. Refer to SRS-36, "
DRIVER AIR BAG MODULE" .
3. Disconnect steering switch connector, remove steering wheel lock nut, then remove steering wheel. Refer
to SRS-38, "
SPIRAL CABLE" .
4. Remove steering column cover. Refer to IP-10, "
INSTRUMENT PANEL ASSEMBLY" .
5. Remove combination switch & spiral cable from steering column assembly. Refer to SRS-38, "
SPIRAL
CABLE" .
6. Remove instrument lower panel (driver side). Refer to IP-10, "
INSTRUMENT PANEL ASSEMBLY" .
7. Remove combination meter. Refer to IP-10, "
INSTRUMENT PANEL ASSEMBLY" .
1. Steering wheel lock nut 2. Steering wheel 3. Lid
4. Combination switch & spiral cable 5. Steering column assembly 6. Collar
7. Hole cover seal 8. Clamp 9. Hole cover
10. Lower shaft 11. Lower joint 12. Steering column assembly (with
Automatic Drive Positioner)
SGIA0551E

STEERING COLUMN
PS-13
C
D
E
F
H
I
J
K
L
MA
B
PS
Revision: 2004 November 2004 FX35/FX45
8. Remove fixing bolts of knee protector, then remove knee protec-
tor from vehicle.
9. Disconnect harness connector from each switch on steering col-
umn shaft, then separate vehicle side harness from it.
10. Remove lock nut and bolt, then separate lower shaft from upper
joint of steering column assembly.
11. Remove fixing bolts and nuts from steering member, remove
steering column assembly from steering member.
12. Remove hole cover seal and clamp.
13. Remove mounting nuts, then remove hole cover from panel.
14. Raise vehicle, then remove mounting bolts of lower joint.
15. Remove lower joint and lower shaft from vehicle.
SGIA0552E
SGIA0554E
SGIA0555E
SGIA0557E