window wiring INFINITI FX35 2004 Service Manual

ATC-1
AUTOMATIC AIR CONDITIONER
J AIR CONDITIONER
CONTENTS
C
D
E
F
G
H
I
K
L
M
SECTION AT C
A
B
AT C
Revision: 2004 November 2004 FX35/FX45
AUTOMATIC AIR CONDITIONER
PRECAUTIONS .......................................................... 5
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 5
Precautions for Working with HFC-134a (R-134a) ..... 5
CONTAMINATED REFRIGERANT ....................... 5
General Refrigerant Precautions .............................. 7
Lubricant Precautions .............................................. 7
Precautions for Refrigerant Connection ................... 8
ABOUT ONE-TOUCH JOINT ................................ 8
FEATURES OF NEW TYPE REFRIGERANT
CONNECTION .................................................... 10
O-RING AND REFRIGERANT CONNECTION .... 11
Precautions for Servicing Compressor ................... 13
Precautions for Service Equipment ........................ 13
RECOVERY/RECYCLING EQUIPMENT ............ 13
ELECTRONIC LEAK DETECTOR ...................... 13
VACUUM PUMP ................................................. 14
MANIFOLD GAUGE SET .................................... 14
SERVICE HOSES ............................................... 14
SERVICE COUPLERS ........................................ 15
REFRIGERANT WEIGHT SCALE ...................... 15
CHARGING CYLINDER ...................................... 15
Precautions for Leak Detection Dye ....................... 16
IDENTIFICATION ................................................ 16
IDENTIFICATION LABEL FOR VEHICLE ........... 16
Wiring Diagrams and Trouble Diagnosis ................ 16
PREPARATION ......................................................... 17
Special Service Tools ............................................. 17
HFC-134a (R-134a) Service Tools and Equipment ... 18
Commercial Service Tools ...................................... 20
REFRIGERATION SYSTEM ..................................... 21
Refrigerant Cycle ................................................... 21
REFRIGERANT FLOW ....................................... 21
FREEZE PROTECTION ..................................... 21
Refrigerant System Protection ............................... 21
REFRIGERANT PRESSURE SENSOR ............. 21
PRESSURE RELIEF VALVE ............................... 21
V-6 Variable Displacement Compressor ................. 22
GENERAL INFORMATION ................................. 22DESCRIPTION .................................................... 23
Component Layout ................................................. 26
LUBRICANT .............................................................. 27
Maintenance of Lubricant Quantity in Compressor ... 27
LUBRICANT ........................................................ 27
LUBRICANT RETURN OPERATION .................. 27
LUBRICANT ADJUSTING PROCEDURE FOR
COMPONENTS REPLACEMENT EXCEPT
COMPRESSOR .................................................. 28
LUBRICANT ADJUSTING PROCEDURE FOR
COMPRESSOR REPLACEMENT ....................... 29
AIR CONDITIONER CONTROL ............................... 30
Description of Air Conditioner LAN Control System ... 30
System Construction .............................................. 30
OPERATION ........................................................ 30
TRANSMISSION DATA AND TRANSMISSION
ORDER ............................................................... 31
AIR MIX DOOR CONTROL (AUTOMATIC TEM-
PERATURE CONTROL) ..................................... 32
FAN SPEED CONTROL ...................................... 32
INTAKE DOOR CONTROL ................................. 32
OUTLET DOOR CONTROL ................................ 32
MAGNET CLUTCH CONTROL ........................... 33
SELF-DIAGNOSTIC SYSTEM ............................ 33
Description of Control System ................................ 34
Control Operation ................................................... 34
DISPLAY SCREEN .............................................. 35
AUTO SWITCH ................................................... 35
TEMPERATURE SWITCH (POTENTIO TEM-
PERATURE CONTROL) (DRIVER SIDE) ........... 35
TEMPERATURE SWITCH (POTENTIO TEM-
PERATURE CONTROL) (PASSENGER SIDE) ... 35
RECIRCULATION (REC) SWITCH ..................... 35
FRESH (FRE) SWITCH ...................................... 35
DEFROSTER (DEF) SWITCH ............................. 35
REAR WINDOW DEFOGGER SWITCH ............. 35
OFF SWITCH ...................................................... 35
A/C SWITCH ....................................................... 35
MODE SWITCH .................................................. 35
FAN SWITCH ...................................................... 35

AV-2Revision: 2004 November 2004 FX35/FX45Antenna Amp. Inspection ....................................... 51
Location of Antenna ................................................ 52
Window Antenna Repair ......................................... 52
CHECK ELEMENT .............................................. 52
Removal and Installation of Roof Antenna ............. 54
REMOVAL ........................................................... 54
INSTALLATION .................................................... 54
INTEGRATED DISPLAY SYSTEM ............................ 55
System Description ................................................. 55
A/C AND AV SWITCH SYSTEM .......................... 55
PRECAUTION OF LCD MONITOR ..................... 55
POWER SUPPLY AND GROUND ....................... 55
DRIVE COMPUTER ............................................ 56
E/M SWITCH ....................................................... 57
SETTING SCREEN ............................................. 58
WARNING INDICATIONS ................................... 59
AV COMMUNICATION LINE ............................... 59
CAN Communication System Description .............. 60
CAN Communication Unit ....................................... 61
Component Parts and Harness Connector Location ... 61
Schematic ............................................................... 62
Wiring Diagram — INF/D — ................................... 63
Schematic ............................................................... 68
Wiring Diagram — COMM — ................................. 69
Terminals and Reference Value for Display Unit .... 72
Terminals and Reference Value for A/C and AV
Switch ..................................................................... 73
On Board Self-Diagnosis Function ......................... 74
DESCRIPTION .................................................... 74
DIAGNOSIS ITEM ............................................... 74
Self-Diagnosis Mode .............................................. 74
OPERATION PROCEDURES ............................. 74
NETWORK CHECK ............................................. 75
PARTS CHECK ................................................... 76
HVAC DETAIL SCREEN ...................................... 76
VERSION CHECK ............................................... 76
CAN DIAG MNTR (CAN DIAG MONITOR) ......... 76
A/C and AV Switch Self-Diagnosis Function ........... 77
STARTING THE SELF-DIAGNOSIS MODE ........ 77
DIAGNOSIS FUNCTION ..................................... 77
EXITING THE SELF-DIAGNOSIS MODE ........... 77
Trouble Diagnosis Chart by Symptom .................... 78
Power Supply and Ground Circuit Check for Display
Unit ......................................................................... 79
Power Supply and Ground Circuit Check for A/C and
AV Switch ................................................................ 80
Vehicle Speed Signal Inspection ............................ 80
Illumination Signal Inspection ................................. 81
Ignition Signal Inspection ........................................ 82
Audio Communication Line Inspection ................... 82
A/C and AV Switch Does Not Operate .................... 84
CAN Communication Line Inspection ..................... 85
Audio Steering Wheel Switch Inspection ................ 85
Removal and Installation of Display ........................ 87
REMOVAL ........................................................... 87
INSTALLATION .................................................... 87
Removal and Installation of A/C and AV Switch ..... 87
NAVIGATION SYSTEM ............................................. 88
System Description ................................................. 88TRAVEL DISTANCE ............................................ 88
TRAVEL DIRECTION .......................................... 88
MAP-MATCHING ................................................. 88
GPS (GLOBAL POSITIONING SYSTEM) .......... 89
COMPONENT DESCRIPTION ............................ 90
BIRDVIEW™ ........................................................ 90
MAP DISPLAY ..................................................... 91
FUNCTION OF CENTER SWITCH ..................... 92
“VIEW” MODE ...................................................... 98
“HEADING” MODE .............................................. 99
“NEARBY DISPLAY ICONS” MODE .................... 99
“SAVE CURRENT LOCATION” MODE ................ 99
“ADJUST CURRENT LOCATION” MODE ........... 99
“AUTO RE-ROUTE” MODE ...............................100
“AVOID AREA SETTING” MODE ......................100
“CLEAR MEMORY” MODE ................................100
“EDIT ADDRESS BOOK” MODE .......................101
“GPS INFORMATION” MODE ...........................101
“QUICK STOP CUSTOMER SETTING” MODE .101
“SET AVERAGE SPEED” MODE ......................101
“TRACKING” MODE ..........................................102
GUIDANCE VOLUME ........................................102
DISPLAY WITH PUSHED “TRIP” BUTTON .......102
TRIP 1 OR TRIP 2 .............................................103
FUEL ECONOMY ..............................................103
MAINTENANCE .................................................103
ENGINE OIL OR TIRE ROTATION ....................103
TIRE PRESSURE ..............................................104
WARNING INDICATIONS ..................................104
CAN Communication System Description ............105
CAN Communication Unit .....................................105
Component Parts Location and Harness Connector
Location ................................................................105
Schematic—NAVI— ..............................................106
Wiring Diagram —NAVI— .....................................107
Schematic — COMM — ........................................115
Wiring Diagram — COMM — ................................116
Terminals and Reference Value for NAVI Control
Unit ........................................................................121
Terminals and Reference Value for Display Control
Unit ........................................................................123
Terminals and Reference Value for Display ..........127
Terminals and Reference Value for A/C and AV
Switch ...................................................................129
On Board Self-Diagnosis Function ........................130
DESCRIPTION ..................................................130
DIAGNOSIS ITEM .............................................130
Self-Diagnosis Mode (DCU) ..................................131
OPERATION PROCEDURE ..............................131
SELF–DIAGNOSIS RESULT .............................133
Self-Diagnosis Mode (NAVI) .................................133
OPERATION PROCEDURE ..............................133
SELF–DIAGNOSIS RESULT .............................135
Confirmation/Adjustment Mode .............................136
OPERATION PROCEDURE ..............................136
DISPLAY DIAGNOSIS .......................................136
VEHICLE SIGNALS ...........................................137
AUTO CLIMATE CONTROL ..............................137
NAVIGATION .....................................................138

AV-38
AUDIO
Revision: 2004 November 2004 FX35/FX45
Noise InspectionAKS00BMR
The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunction.
Check if noise is caused and/or changed by engine speed, ignition switch turned to each position, and opera-
tion of each piece of electrical equipment, and determine the cause.
NOTE:
The source of the noise can be found easily by listening to the noise while removing the fuses of electrical
components, one by one.
TYPE OF NOISE AND POSSIBLE CAUSE
Occurrence condition Possible cause
Occurs only when engine is
ON.A continuous growling noise occurs. The speed
of the noise varies with changes in the engine
speed.

Ignition condenser
A whistling noise occurs while the engine speed
is high. A booming noise occurs while the engine
is running and the lighting switch is ON.

Alternator
The occurrence of the noise is linked with the operation of the fuel pump.

Fuel pump condenser
Noise only occurs when various
electrical components are oper-
ating.A cracking or snapping sound occurs with the
operation of various switches.

Relay malfunction, radio malfunction
The noise occurs when various motors are oper-
ating.

Motor case ground

Motor
The noise occurs constantly, not just under certain conditions.

Rear window defogger coil malfunction

Open circuit in printed heater

Poor ground of antenna amplifier or
antenna feeder line

Mirror type film is attached on the rear win-
dow glass

After-market TV antenna and/or electrical
accessories such as radio are attached on
the rear window glass.
A cracking or snapping sound occurs while the vehicle is being driven, especially
when it is vibrating excessively.

Ground wire of body parts.

Ground due to incorrectinstallation of
parts.

Wiring connections or ashort circuit.

REMOTE KEYLESS ENTRY SYSTEM
BL-59
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2004 November 2004 FX35/FX45
Refer to AV- 5 8 , "SETTING SCREEN" . (without navigation system)
Refer to AV- 9 5 , "
Vehicle Electronic Systems" . (with navigation system)
Panic Alarm Operation
When key switch is OFF (when ignition key is not inserted in key cylinder), BCM turns on and off horn and
headlamp intermittently with input of PANIC ALARM signal from key fob.
The alarm automatically turns off after 25 seconds or when BCM receives any signal from key fob.
Panic alarm operation mode can be changed using “PANIC ALARM SET” mode in “WORK SUPPORT”.
Refer to BL-67, "
Work Support" .
For detailed description, refer to BL-181, "
VEHICLE SECURITY (THEFT WARNING) SYSTEM" .
Keyless Power Window Down (open) Operation
When key fob unlock switch is turned ON with ignition switch OFF, and key fob unlock switch is detected to be
on continuously for 3 seconds, the driver's door and passenger's door power windows are simultaneously
opened.
Power window is operated to open and the operation continues as long as the key fob unlock switch is
pressed.
Keyless power window down operation mode can be changed using “PW DOWN SET” mode in “WORK SUP-
PORT”. Refer to BL-67, "
Work Support"
Room Lamp and Ignition Key ring Illumination Operation
When the following conditions come:

condition of interior lamp switch is DOOR position;

door switch OFF (when all the doors are closed);
Remote keyless entry system turns on interior lamp (for 30 seconds) with input of UNLOCK signal from key
fob. For detailed description, refer to LT- 1 5 7 , "
INTERIOR ROOM LAMP" .
CAN Communication System DescriptionAIS004MC
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitAIS004RM
Refer to LAN-6, "CAN COMMUNICATION" .

EC-40
[VQ35DE]
BASIC SERVICE PROCEDURE
Revision: 2004 November 2004 FX35/FX45
INSPECTION PROCEDURE
1. INSPECTION START
1. Check service records for any recent repairs that may indicate a related malfunction, or a current need for
scheduled maintenance.
2. Open engine hood and check the following:
–Harness connectors for improper connections
–Wiring harness for improper connections, pinches and cut
–Vacuum hoses for splits, kinks and improper connections
–Hoses and ducts for leaks
–Air cleaner clogging
–Gasket
3. Confirm that electrical or mechanical loads are not applied.
–Headlamp switch is OFF.
–Air conditioner switch is OFF.
–Rear window defogger switch is OFF.
–Steering wheel is in the straight-ahead position, etc.
4. Start engine and warm it up until engine coolant temperature
indicator points the middle of gauge.
Ensure engine stays below 1,000 rpm.
5. Run engine at about 2,000 rpm for about 2 minutes under no-
load.
6. Make sure that no DTC is displayed with CONSULT-II or GST.
OK or NG
OK >> GO TO 3.
NG >> GO TO 2.
2. REPAIR OR REPLACE
Repair or replace components as necessary according to corresponding Diagnostic Procedure.
>> GO TO 3.
SEF983U
SEF976U
SEF977U

TROUBLE DIAGNOSIS
EC-83
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2004 November 2004 FX35/FX45
Basic InspectionABS006KR
1. INSPECTION START
1. Check service records for any recent repairs that may indicate a related malfunction, or a current need for
scheduled maintenance.
2. Open engine hood and check the following:
–Harness connectors for improper connections
–Wiring harness for improper connections, pinches and cut
–Vacuum hoses for splits, kinks and improper connections
–Hoses and ducts for leaks
–Air cleaner clogging
–Gasket
3. Confirm that electrical or mechanical loads are not applied.
–Headlamp switch is OFF.
–Air conditioner switch is OFF.
–Rear window defogger switch is OFF.
–Steering wheel is in the straight-ahead position, etc.
4. Start engine and warm it up until engine coolant temperature
indicator points the middle of gauge.
Ensure engine stays below 1,000 rpm.
5. Run engine at about 2,000 rpm for about 2 minutes under no-
load.
6. Make sure that no DTC is displayed with CONSULT-II or GST.
OK or NG
OK >> GO TO 3.
NG >> GO TO 2.
2. REPAIR OR REPLACE
Repair or replace components as necessary according to corresponding Diagnostic Procedure.
>> GO TO 3.
SEF983U
SEF976U
SEF977U

BASIC SERVICE PROCEDURE
EC-689
[VK45DE]
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2004 November 2004 FX35/FX45
INSPECTION PROCEDURE
1. INSPECTION START
1. Check service records for any recent repairs that may indicate a related malfunction, or a current need for
scheduled maintenance.
2. Open engine hood and check the following:
–Harness connectors for improper connections
–Wiring harness for improper connections, pinches and cut
–Vacuum hoses for splits, kinks and improper connections
–Hoses and ducts for leaks
–Air cleaner clogging
–Gasket
3. Confirm that electrical or mechanical loads are not applied.
–Headlamp switch is OFF.
–Air conditioner switch is OFF.
–Rear window defogger switch is OFF.
–Steering wheel is in the straight-ahead position, etc.
4. Start engine and warm it up until engine coolant temperature
indicator points the middle of gauge.
Ensure engine stays below 1,000 rpm.
5. Run engine at about 2,000 rpm for about 2 minutes under no
load.
6. Make sure that no DTC is displayed with CONSULT-II or GST.
OK or NG
OK >> GO TO 3.
NG >> GO TO 2.
2. REPAIR OR REPLACE
Repair or replace components as necessary according to corresponding Diagnostic Procedure.
>> GO TO 3.
SEF983U
SEF976U
SEF977U

TROUBLE DIAGNOSIS
EC-733
[VK45DE]
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2004 November 2004 FX35/FX45
Basic InspectionABS00BZR
1. INSPECTION START
1. Check service records for any recent repairs that may indicate a related malfunction, or a current need for
scheduled maintenance.
2. Open engine hood and check the following:
–Harness connectors for improper connections
–Wiring harness for improper connections, pinches and cut
–Vacuum hoses for splits, kinks and improper connections
–Hoses and ducts for leaks
–Air cleaner clogging
–Gasket
3. Confirm that electrical or mechanical loads are not applied.
–Head lamp switch is OFF.
–Air conditioner switch is OFF.
–Rear window defogger switch is OFF.
–Steering wheel is in the straight-ahead position, etc.
4. Start engine and warm it up until engine coolant temperature
indicator points the middle of gauge.
Ensure engine stays below 1,000 rpm.
5. Run engine at about 2,000 rpm for about 2 minutes under no
load.
6. Make sure that no DTC is displayed with CONSULT-II or GST.
OK or NG
OK >> GO TO 3.
NG >> GO TO 2.
2. REPAIR OR REPLACE
Repair or replace components as necessary according to corresponding Diagnostic Procedure.
>> GO TO 3.
SEF983U
SEF976U
SEF977U

SERVICE INFORMATION FOR ELECTRICAL INCIDENT
GI-29
C
D
E
F
G
H
I
J
K
L
MB
GI
Revision: 2004 November 2004 FX35/FX45
UNDER SEATING AREAS
An unclamped or loose harness can cause wiring to be pinched by seat components (such as slide guides)
during vehicle vibration. If the wiring runs under seating areas, inspect wire routing for possible damage or
pinching.
Heat Sensitive
The customer's concern may occur during hot weather or after car
has sat for a short time. In such cases you will want to check for a
heat sensitive condition.
To determine if an electrical component is heat sensitive, heat the
component with a heat gun or equivalent.
Do not heat components above 60°C (140°F). If incident occurs
while heating the unit, either replace or properly insulate the compo-
nent.
Freezing
The customer may indicate the incident goes away after the car
warms up (winter time). The cause could be related to water freezing
somewhere in the wiring/electrical system.
There are two methods to check for this. The first is to arrange for
the owner to leave his car overnight. Make sure it will get cold
enough to demonstrate his complaint. Leave the car parked outside
overnight. In the morning, do a quick and thorough diagnosis of
those electrical components which could be affected.
The second method is to put the suspect component into a freezer
long enough for any water to freeze. Reinstall the part into the car
and check for the reoccurrence of the incident. If it occurs, repair or
replace the component.
Water Intrusion
The incident may occur only during high humidity or in rainy/snowy
weather. In such cases the incident could be caused by water intru-
sion on an electrical part. This can be simulated by soaking the car
or running it through a car wash.
Do not spray water directly on any electrical components.
Electrical Load
The incident may be electrical load sensitive. Perform diagnosis with
all accessories (including A/C, rear window defogger, radio, fog
lamps) turned on.
SGI842
SGI843
SGI844
SGI845

GW-1
GLASSES, WINDOW SYSTEM & MIRRORS
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION GW
A
B
GW
Revision: 2004 November 2004 FX35/FX45
GLASSES, WINDOW SYSTEM & MIRRORS
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Handling for Adhesive and Primer ........................... 3
Wiring Diagrams and Trouble Diagnosis .................. 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
Commercial Service Tools ........................................ 4
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 5
Work Flow ................................................................ 5
CUSTOMER INTERVIEW ..................................... 5
DUPLICATE THE NOISE AND TEST DRIVE ....... 6
CHECK RELATED SERVICE BULLETINS ........... 6
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ...................................................... 6
REPAIR THE CAUSE ........................................... 6
CONFIRM THE REPAIR ....................................... 7
Generic Squeak and Rattle Troubleshooting ........... 7
INSTRUMENT PANEL .......................................... 7
CENTER CONSOLE ............................................. 7
DOORS ................................................................. 7
TRUNK .................................................................. 8
SUNROOF/HEADLINING ..................................... 8
SEATS ................................................................... 8
UNDERHOOD ....................................................... 8
Diagnostic Worksheet .............................................. 9
WINDSHIELD GLASS ...............................................11
Removal and Installation ......................................... 11
REMOVAL ............................................................ 11
INSTALLATION ................................................... 12
REAR WINDOW GLASS AND MOLDING ............... 13
Removal and Installation ........................................ 13
REMOVAL ........................................................... 13
INSTALLATION ................................................... 14
POWER WINDOW SYSTEM .................................... 15
Component Parts and Harness Connector Location ... 15
System Description ................................................ 16
WITH FRONT POWER WINDOW ANTI-PINCH
SYSTEM ............................................................. 16WITH FRONT AND REAR WINDOW ANTI-
PINCH SYSTEM ................................................. 16
MANUAL OPERATION ........................................ 17
AUTO OPERATION ............................................. 19
POWER WINDOW SERIAL LINK ....................... 20
POWER WINDOW LOCK ................................... 20
RETAINED POWER OPERATION ...................... 21
ANTI-PINCH SYSTEM ........................................ 21
POWER WINDOW CONTROL BY THE KEY
CYLINDER SWITCH ........................................... 21
CAN Communication System Description .............. 22
CAN Communication Unit ....................................... 22
Schematic (With Front Power Window Anti-pinch
System) .................................................................. 23
Wiring Diagram —WINDOW— (With Front Power
Window Anti-pinch System) .................................... 24
Terminal and Reference Value for BCM / With Front
Power Window Anti-pinch System .......................... 28
Terminal and Reference Value for Power Window
Main Switch / With Front Power Window Anti-pinch
System .................................................................... 29
Terminal and Reference Value for Front Power Win-
dow Switch (Passenger Side) / With Front Power
Window Anti-pinch System ..................................... 30
Schematic (With Front and Rear Power Window
Anti-pinch System) ................................................. 31
Wiring Diagram —WINDOW— (With Front and
Rear Power Window Anti-pinch System) ................ 32
Terminal and Reference Value for BCM / With Front
and Rear Power Window Anti-pinch ....................... 37
Terminal and Reference Value for Power Window
Main Switch / With Front and Rear Power Window
Anti-pinch System ................................................... 38
Terminal and Reference Value for (Front and Rear)
Power Window Switch / With Front and Rear Win-
dow Anti-pinch System ........................................... 39
Work Flow ............................................................... 39
CONSULT-II Inspection Procedure ......................... 40
ACTIVE TEST ..................................................... 41
WORK SUPPORT ............................................... 41