engine oil INFINITI FX35 2005 Service Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2005, Model line: FX35, Model: INFINITI FX35 2005Pages: 4731, PDF Size: 60.13 MB
Page 3165 of 4731
FFD-14
FRONT FINAL DRIVE ASSEMBLY
Revision: 2005 July 2005 FX
Removal and Installation (VK45DE Models)ADS0019Q
COMPONENTS
REMOVAL
1. Remove three way catalyst (right bank). Refer to EM-182, "EXHAUST MANIFOLD AND THREE WAY
CATALYST" .
2. Remove stabilizer assembly with power tool. Refer to FSU-16, "
STABILIZER BAR" .
3. Remove steering gearbox mounting bolts with power tool. Refer to PS-19, "
POWER STEERING GEAR
AND LINKAGE" .
4. Remove front drive shaft both. Refer to FAX-12, "
FRONT DRIVE SHAFT" .
5. Remove side shaft assembly.
6. Remove front propeller shaft. Refer to PR-4, "
FRONT PROPELLER SHAFT" .
7. Remove front suspension member with power tool. Refer to FSU-17, "
FRONT SUSPENSION MEMBER" .
8. Remove engine wire harness clamp bolts from front final drive.
9. Remove breather hose and tube.
10. Remove mounting bolts and remove front final drive assembly from the vehicle.
INSTALLATION
Note the following, and installation is in the reverse order of removal.
Refer to FFD-14, "COMPONENTS" about each tightening torque.
When installing side shaft, apply multi-purpose grease to contact surface of side shaft and side shaft oil
seal.
1. Front final drive assembly 2. Side shaft 3. Bushing
4. Front propeller shaft 5. Breather tube 6. Breather hose
7. Breather connector 8. Harness bracket
PDIA0659E
Page 3205 of 4731
FSU-2
PRECAUTIONS
Revision: 2005 July 2005 FX
PRECAUTIONSPFP:00001
CautionAES000MZ
When installing rubber bushings, final tightening must be carried out under unladen conditions with tires
on ground. Oil will shorten the life of rubber bushings. Be sure to wipe off any spilled oil.
Unladen conditions mean that fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and
mats are in designated positions.
After servicing suspension parts, be sure to check wheel alignment.
Caulking nuts are not reusable. Always use new ones when installing. Since new caulking nuts are pre-
oiled, tighten as they are.
Avoid burden to front cross bar.
Page 3209 of 4731
FSU-6
FRONT SUSPENSION ASSEMBLY
Revision: 2005 July 2005 FX
FRONT SUSPENSION ASSEMBLYPFP:54010
On-Vehicle Inspection and ServiceAES000N3
Make sure the mounting conditions (looseness, back lash) of each component and component statues (wear,
damage) are normal.
INSPECTION OF TRANSVERSE LINK BALL JOINT END PLAY
1. Set front wheels in a straight-ahead position. Do not depress brake pedal.
2. Measure axial end play by installing and moving up/down between transverse link and steering knuckle with an iron pry bar or something similar.
CAUTION:
Be careful not to damage ball joint boot.
STRUT INSPECTION
Check strut for oil leakage, damage and replace if necessary. Refer to FSU-11, "COIL SPRING AND STRUT" .
Wheel Alignment InspectionAES000N4
DESCRIPTION
Measure wheel alignment under unladen conditions.
NOTE:
Unladen conditions mean that fuel, engine coolant, and lubricant are full. Spare tire, jack, hand tools and mats
are designated positions.
PRELIMINARY CHECK
1. Check tires for improper air pressure and wear.
2. Check road wheels for runout.
3. Check wheel bearing axial end play.
4. Check transverse link ball joint axial end play.
5. Check strut operation.
6. Check each mounting part of axle and suspension for looseness and deformation.
7. Check each link, rod and member for cracks, deformation and other damage.
8. Check vehicle posture.
INSPECTION OF CAMBER, CASTER AND KINGPIN INCLINATION ANGLES
Camber, caster, kingpin inclination angles cannot be adjusted.
Before inspection, mount front wheels onto turning radius gauge. Mount rear wheels onto a stand that has
same height so vehicle will remain horizontal.
Using a CCK Gauge
Install CCK gauge attachment (SST: KV991040S0) as following procedure in wheel, then measure wheel
alignment.
1. Remove wheel nuts (3), and install a guide bolt to hub bolt.
2. Screw adapter into plate body until it contacts body tightly.
3. Screw center plate into plate.
4. Insert plate on guide bolt. Put spring in, and then evenly screw both guide bolt nut. When fastening guide bolt nut, do not com-
pletely compress spring. Axial end play : 0 mm (0 in)
SEIA0240E
Page 3212 of 4731
FRONT SUSPENSION ASSEMBLY FSU-9
C
D
F
G H
I
J
K L
M A
B
FSU
Revision: 2005 July 2005 FX
Removal and InstallationAES000N6
REMOVAL
1. Set an engine slinger to engine, then suspend engine.
2. Remove tire from vehicle with power tool.
3. Remove brake caliper with power tool. Hang it in a place where it will not interfere with work. Refer to BR-
20, "FRONT DISC BRAKE" .
4. Remove brake hose lock plate. Then remove brake hose from strut assembly.
5. Remove disc rotor.
6. Remove wheel sensor harness from strut assembly. CAUTION:
Do not pull on wheel sensor harness.
7. Remove undercover with power tool.
8. Remove front cross bar.
9. Remove steering hydraulic piping bracket from front suspension member. Refer to PS-41, "
HYDRAULIC LINE" .
10. Remove cotter pin at steering outer socket, then loosen mount- ing nut.
11. Use a ball joint remover (SST) to remove steering outer socket from steering knuckle. Be careful not to damage ball joint boot.
CAUTION:
Tighten temporarily mounting nut to prevent damage to
threads and to prevent ball joint remover (SST) from com-
ing off.
12. Remove mounting bolts of steering gear with power tool, then hang steering gear on vehicle. Refer to PS-19, "
POWER
STEERING GEAR AND LINKAGE" .
13. Remove front final drive side of drive shaft with power tool. (For AWD models) Refer to FAX-12, "
Removal and Installation (Left
Side)" , FA X - 1 3 , "Removal and Installation (Right Side)" .
14. Set jack under front suspension member.
15. Remove fixing bolts and nuts between strut assembly and steering knuckle with power tool.
1. Strut upper plate 2. Strut spacer 3. Mounting insulator
4. Mounting insulator bracket 5. Mounting bearing 6. Spring upper seat
7. Spring upper rubber seat 8. Coil spring 9. Spring lower rubber seat
10. Bound bumper 11. Strut 12. Steering knuckle
13. Front suspension member 14. Transverse link 15. Stabilizer bar
16. Stabilizer bushing 17. Stabilizer clamp 18. Stabilizer connecting rod
19. Front cross bar 20. Cotter pin
SEIA0328E
SEIA0329E
SDIA1434E
Page 3221 of 4731
FSU-18
SERVICE DATA
Revision: 2005 July 2005 FX
SERVICE DATAPFP:00030
Wheel Alignment (Unladen)AES000NC
Ball JointAES000ND
Wheelarch Height (Unladen*)AES000OM
*: Fuel, engine coolant and engine oil full. Spare tire, jack, hand tools and mats are in designated positions. Camber
Degree minute (Decimal degree) Minimum
− 1 °29 ′ ( − 1.48 °)
Nominal − 0 °44 ′ ( − 0.73 °)
Maximum 0 °01 ′ (0.02 °)
Left and right difference 45 ′ (0.75 °) or less
Caster
Degree minute (Decimal degree) Minimum 3
°02 ′ (3.03 °)
Nominal 3 °47 ′ (3.78 °)
Maximum 4 °32 ′ (4.53 °)
Left and right difference 45 ′ (0.75 °) or less
Kingpin inclination
Degree minute (Decimal degree) Minimum 12
° 20 ′ (12.33 °)
Nominal 13 ° 05 ′ (13.08 °)
Maximum 13 °50 ′ (13.83 °)
Total toe-in Distance (A – B) Minimum 0.6 mm (0.024 in)
Nominal 1.6 mm (0.063 in)
Maximum 2.6 mm (0.102 in)
Axial end play 0.1 mm (0.004 in)
Swing torque 0.5 − 4.9 N·m (0.06 − 0.49 kg-m, 5 − 43 in-lb)
Measurement on spring balance 0.5 − 4.9 N·m (0.06 − 0.49 kg-m, 5 − 43 in-lb)
Destination USA Canada
Engine VQ35DE VK45DE VQ35DE VK45DE
Axle 2WD AWD AWD
Tire size 265/60R18 265/50R20 265/60R18 265/50R20 265/60R18 265/50R20
Front (Hf) 835 mm
(32.87 in) 834 mm
(32.83 in) 834 mm
(32.83 in) 833 mm
(32.80 in) 832 mm
(32.76 in) 834 mm
(32.83 in) 833 mm
(32.80 in) 832 mm
(32.76 in)
Rear (Hr) 822 mm
(32.36 in) 821 mm
(32.32 in) 829 mm
(32.64 in) 827 mm
(32.56 in) 825 mm
(32.48 in) 827 mm
(32.56 in) 826 mm
(32.52 in) 823 mm
(32.40 in)
SFA818A
Page 3222 of 4731
GI-1
GENERAL INFORMATION
A GENERAL INFORMATION
CONTENTS
C
D E
F
G H
I
J
K L
M B
GI
SECTION GI
Revision: 2005 July
2005 FX
GENERAL INFORMATION
PRECAUTIONS .......................................................... 3
Description .......................................................... ..... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 3
Precautions for NVIS/IVIS (NISSAN/INFINITI
VEHICLE IMMOBILIZER SYSTEM - NATS) (If
Equipped) ............................................................ ..... 3
Precautions Necessary for Steering Wheel Rotation
After Battery Disconnect ..................................... ..... 4
OPERATION PROCEDURE ............................ ..... 4
Precautions for Procedures without Cowl Top Cover ..... 4
General Precautions ........................................... ..... 4
Precautions for Three Way Catalyst .................... ..... 6
Precautions for Fuel (Unleaded Premium Gasoline
Recommended) ................................................... ..... 6
Precautions for Fuel (Unleaded Premium Gasoline
Required) ............................................................ ..... 7
Precautions for Multiport Fuel Injection System or
Engine Control System ....................................... ..... 7
Precautions for Hoses ......................................... ..... 7
HOSE REMOVAL AND INSTALLATION .......... ..... 7
HOSE CLAMPING ........................................... ..... 8
Precautions for Engine Oils ................................. ..... 8
HEALTH PROTECTION PRECAUTIONS ........ ..... 8
ENVIRONMENTAL PROTECTION PRECAU-
TIONS .............................................................. ..... 8
Precautions for Air Conditioning .......................... ..... 8
HOW TO USE THIS MANUAL .............................. ..... 9
Description .......................................................... ..... 9
Terms .................................................................. ..... 9
Units .................................................................... ..... 9
Contents .............................................................. ..... 9
Components ........................................................ ... 10
SYMBOLS ........................................................ ... 10
How to Follow Trouble Diagnoses ....................... .... 11
DESCRIPTION ................................................. .... 11
HOW TO FOLLOW TEST GROUPS IN TROU-
BLE DIAGNOSES ............................................ .... 11
HARNESS WIRE COLOR AND CONNECTOR NUMBER INDICATION ....................................
... 12
KEY TO SYMBOLS SIGNIFYING MEASURE-
MENTS OR PROCEDURES ............................ ... 13
How to Read Wiring Diagrams ............................ ... 15
CONNECTOR SYMBOLS ................................ ... 15
SAMPLE/WIRING DIAGRAM - EXAMPL - ....... ... 16
DESCRIPTION ................................................. ... 17
Abbreviations ....................................................... ... 23
SERVICE INFORMATION FOR ELECTRICAL INCI-
DENT ...................................................................... ... 24
How to Check Terminal ........................................ ... 24
CONNECTOR AND TERMINAL PIN KIT ......... ... 24
HOW TO PROBE CONNECTORS ................... ... 24
How to Perform Efficient Diagnosis for an Electrical
Incident ................................................................ ... 27
WORK FLOW ................................................... ... 27
INCIDENT SIMULATION TESTS ..................... ... 27
CIRCUIT INSPECTION .................................... ... 30
Control Units and Electrical Parts ........................ ... 35
PRECAUTIONS ............................................... ... 35
CONSULT-II CHECKING SYSTEM ....................... ... 37
Description ........................................................... ... 37
Function and System Application ........................ ... 37
Nickel Metal Hydride Battery Replacement ......... ... 38
Checking Equipment ........................................... ... 38
CONSULT-II Start Procedure ............................... ... 38
CONSULT-II Data Link Connector (DLC) Circuit . ... 39
INSPECTION PROCEDURE ........................... ... 39
CIRCUIT DIAGRAM ......................................... ... 40
LIFTING POINT ...................................................... ... 41
Special Service Tools .......................................... ... 41
Garage Jack and Safety Stand ............................ ... 41
2-Pole Lift ............................................................ ... 42
Board-On Lift ....................................................... ... 43
TOW TRUCK TOWING .......................................... ... 44
Tow Truck Towing ................................................ ... 44
2WD MODELS ................................................. ... 44
AWD MODELS ................................................. ... 45
Vehicle Recovery (Freeing a Stuck Vehicle) ........ ... 45
AUTOMATIC TRANSMISSION ........................ ... 46
Page 3226 of 4731
PRECAUTIONS GI-5
C
D E
F
G H
I
J
K L
M B
GI
Revision: 2005 July 2005 FX
Before jacking up the vehicle, apply wheel chocks or other tire
blocks to the wheels to prevent the vehicle from moving. After
jacking up the vehicle, support the vehicle weight with safety
stands at the points designated for proper lifting before working
on the vehicle.
These operations should be done on a level surface.
When removing a heavy component such as the engine or tran-
saxle/transmission, be careful not to lose your balance and drop
them. Also, do not allow them to strike adjacent parts, especially
the brake tubes and master cylinder.
Before starting repairs which do not require battery power:
Turn off ignition switch.
Disconnect the negative battery terminal.
If the battery terminals are disconnected, recorded memory of
radio and each control unit is erased.
To prevent serious burns:
Avoid contact with hot metal parts.
Do not remove the radiator cap when the engine is hot.
Dispose of drained oil or the solvent used for cleaning parts in
an appropriate manner.
Do not attempt to top off the fuel tank after the fuel pump nozzle
shuts off automatically.
Continued refueling may cause fuel overflow, resulting in fuel
spray and possibly a fire.
Clean all disassembled parts in the designated liquid or solvent
prior to inspection or assembly.
Replace oil seals, gaskets, packings, O-rings, locking washers, cotter pins, self-locking nuts, etc. with new
ones.
Replace inner and outer races of tapered roller bearings and needle bearings as a set.
Arrange the disassembled parts in accordance with their assembled locations and sequence.
Do not touch the terminals of electrical components which use microcomputers (such as ECM).
Static electricity may damage internal electronic components.
After disconnecting vacuum or air hoses, attach a tag to indicate the proper connection.
Use only the fluids and lubricants specified in this manual.
Use approved bonding agent, sealants or their equivalents when required.
Use hand tools, power tools (disassembly only) and recom-
mended special tools where specified for safe and efficient ser-
vice repairs.
When repairing the fuel, oil, water, vacuum or exhaust systems,
check all affected lines for leaks.
SGI231
SEF289H
SGI233
PBIC0190E
Page 3229 of 4731
GI-8
PRECAUTIONS
Revision: 2005 July 2005 FX
HOSE CLAMPING
If old rubber hose is re-used, install hose clamp in its original
position (at the indentation where the old clamp was). If there is
a trace of tube bulging left on the old rubber hose, align rubber
hose at that position.
Discard old clamps; replace with new ones.
After installing plate clamps, apply force to them in the direction
of the arrow, tightening rubber hose equally all around.
Precautions for Engine OilsAAS000F3
Prolonged and repeated contact with used engine oil may cause skin cancer. Try to avoid direct skin contact
with used oil.
If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible.
HEALTH PROTECTION PRECAUTIONS
Avoid prolonged and repeated contact with oils, particularly used engine oils.
Wear protective clothing, including impervious gloves where practicable.
Do not put oily rags in pockets.
Avoid contaminating clothes, particularly underpants, with oil.
Heavily soiled clothing and oil-impregnated footwear should not be worn. Overalls must be cleaned regu-
larly.
First aid treatment should be obtained immediately for open cuts and wounds.
Use barrier creams, applying them before each work period, to help the removal of oil from the skin.
Wash with soap and water to ensure all oil is removed (skin cleansers and nail brushes will help). Prepa-
rations containing lanolin replace the natural skin oils which have been removed.
Do not use gasoline, kerosene, diesel fuel, gas oil, thinners or solvents for cleaning skin.
If skin disorders develop, obtain medical advice without delay.
Where practical, degrease components prior to handling.
Where there is a risk of eye contact, eye protection should be worn, for example, chemical goggles or face
shields; in addition an eye wash facility should be provided.
ENVIRONMENTAL PROTECTION PRECAUTIONS
Dispose of used oil and used oil filters through authorized waste disposal contractors to licensed waste dis-
posal sites, or to the waste oil reclamation trade. If in doubt, contact the local authority for advice on disposal
facilities.
It is illegal to pour used oil on to the ground, down sewers or drains, or into water sources.
The regulations concerning pollution vary between regions.
Precautions for Air Conditioning AAS000F4
Use an approved refrigerant recovery unit any time the air conditioning system must be discharged. Refer to
ATC/MTC section “HFC-134a (R-134a) Service Procedure”, “REFRIGERANT LINES” for specific instructions.
SMA021D
SMA022D
Page 3397 of 4731
IDX-4
ALPHABETICAL INDEX
ECTS - Wiring diagram ...................... EC-210, EC-916
Electric sunroof .................................................. RF-10
Electric throttle control actuator ........ EC-424, EC-426,
EC-1148
, EC-1150
Electric throttle control actuator (VK45DE) ..... EM-178
Electric throttle control actuator (VQ35DE) ....... EM-19
Electrical load signal circuit .............. EC-679, EC-1369
Electrical unit ..................................................... PG-76
Electrical units location ...................................... PG-70
Electronic ignition (EI) system ............. EC-33, EC-724
Engine control module (ECM) .......... EC-402, EC-1134
Engine control system diagram ....................... EC-721
Engine control system diagram and chart ......... EC-30
Engine coolant temperature sensor (ECTS) ... EC-208,
EC-220
, EC-914, EC-927
Engine coolant(VK45DE) .................................. CO-37
Engine coolant(VQ35DE) ................................. CO-11
Engine oil filter replacement ............................. MA-26
Engine oil filter replacement(VQ35DE) ............. MA-19
Engine oil precautions .......................................... GI-8
Engine oil replacement(VQ35DE) ..................... MA-18
Engine oil(VK45DE) ........................................... LU-25
Engine oil(VQ35DE) ............................................ LU-7
Engine removal(VK45DE) ............................... EM-240
Engine removal(VQ35DE) .............................. EM-112
Engine room cover(VK45DE) ......................... EM-172
ETC1 - Wiring diagram .................... EC-427, EC-1151
ETC2 - Wiring diagram .................... EC-434, EC-1158
ETC3 - Wiring diagram .................... EC-438, EC-1162
EVAP canister ...................................... EC-42, EC-733
EVAP canister purge volume control solenoid valve ....
EC-336
, EC-1069, EC-1233
EVAP canister vent control valve ...... EC-343, EC-568,
EC-1076
, EC-1241
EVAP control system (small leak) diagnosis .. EC-327,
EC-367
, EC-1061, EC-1108
EVAP control system pressure sensor ........... EC-350,
EC-353
, EC-359, EC-1083, EC-1086, EC-1092
EVAP control system purge flow monitoring diagnosis
EC-322
, EC-1056
EVAP vapor lines inspection ................. MA-21, MA-28
Evaporative emission (EVAP) system . EC-39, EC-730
Evaporator ..................................................... ATC-156
Exhaust manifold(VK45DE) ............................ EM-182
Exhaust manifold(VQ35DE) .............................. EM-26
Exhaust system ................................................... EX-3
Exhaust system inspection ..................... EX-3, MA-29
Expansion valve ............................................. ATC-157
F
F/FOG - Wiring diagram ..................................... LT-81
F/PUMP - Wiring diagram ................ EC-669, EC-1359
Final drive pre-inspection .................. FFD-20, RFD-17
Final drive removal and installation .. FFD-12, FFD-14,
RFD-14
Floor trim ............................................................. EI-39
Flow charts ......................................................... GI-27
Fluid temperature sensor (A/T) ........................ AT-136
Fluorescent leak detector ............................. ATC-158
Fog lamp, front ................................................... LT-79
Front axle ............................................ FAX-4, FAX-10
Front brake solenoid valve ................. AT-154, AT-156
Front bumper ...................................................... EI-14
Front door ............................. BL-153, BL-157, GW-76
Front fog lamp .................................................... LT-79
Front passenger air bag .................................. SRS-39
Front seat belt ...................................................... SB-3
Front seat belt pre-tensioner ..... SB-2, SRS-3, SRS-44
Front suspension .............................................. FSU-6
Front washer ...................................................... WW-4
Front wiper ......................................................... WW-4
FTTS - Wiring diagram .... EC-269, EC-274, EC-1006,
EC-1011
Fuel cut control (at no load high engine speed) EC-34,
EC-725
Fuel filter replacement ......................................... FL-4
Fuel gauge ............................................................ DI-5
Fuel injection system (Bank 1) .......... EC-986, EC-995
Fuel injection system (Bank 2) .......... EC-986, EC-995
Fuel injector and fuel tube(VK45DE) .............. EM-192
Fuel injector and fuel tube(VQ35DE) ................ EM-45
Fuel level sensor EC-385, EC-387, EC-389, EC-1117,
EC-1119
, EC-1121
Fuel line inspection .................................. FL-3, MA-25
Fuel line inspection(VQ35DE) .......................... MA-17
Fuel precautions .......................................... GI-6, GI-7
Fuel pressure check ........................... EC-99, EC-789
Fuel pressure release ......................... EC-99, EC-789
Fuel pump ....................................... EC-668, EC-1358
Fuel pump and gauge .......................................... FL-4
Fuel system ......................................................... FL-3
Fuel tank ............................................................ FL-10
Fuel tank temperature sensor .......... EC-267, EC-273,
EC-1004
, EC-1010
Fuel tank vacuum relief valve ............. EC-42, EC-733
FUELB1 - Wiring diagram .. EC-250, EC-260, EC-988,
EC-997
FUELB2 - Wiring diagram .. EC-251, EC-261, EC-989,
EC-998
Fuse .................................................................. PG-17
Fuse and fusible link box .................................. PG-83
Fusible link ........................................................ PG-17
G
Gauges ................................................................. DI-5
Glass ...................................... GW-11, GW-76, GW-80
Glove box lamp ................................... LT-156, LT-202
Grille - See Exterior ............................................ EI-22
Ground distribution ........................................... PG-31
H
H/AIM - Wiring diagram ..................................... LT-75
H/LAMP - Wiring diagram .................................. LT-11
Harness connector ............................................ PG-74
Harness layout .................................................. PG-46
Page 3398 of 4731
IDX-5
A
C
D E
F
G H
I
J
K L
B
IDX
ALPHABETICAL INDEX
Hazard warning lamp ..........................................
LT-91
Headlamp aiming control .................................... LT-75
Headlamp leveler - See Headlamp aiming control .......
LT-75
Headlining - See Roof trim .................................. EI-41
Heated oxygen sensor 1 (bank 1) .... EC-935, EC-944,
EC-956
, EC-1174, EC-1180
Heated oxygen sensor 1 (bank 2) .... EC-935, EC-944,
EC-956
, EC-1174, EC-1180
Heated oxygen sensor 1 heater (bank 1) ........ EC-877
Heated oxygen sensor 1 heater (bank 2) ........ EC-877
Heated oxygen sensor 2 (bank 1) .... EC-228, EC-237,
EC-442
, EC-453, EC-966, EC-975, EC-1187, EC-1198
Heated oxygen sensor 2 (bank 2) .... EC-228, EC-237,
EC-442
, EC-453, EC-966, EC-975, EC-1187, EC-1198
Heated oxygen sensor 2 heater (bank 1) ....... EC-178,
EC-885
Heated oxygen sensor 2 heater (bank 2) ....... EC-178,
EC-885
Heated seat ....................................................... SE-97
Heater and cooling unit (Heater core) ........... ATC-126
HFC134a (R134a) system precaution ............... ATC-6
HFC134a (R134a) system service procedure ATC-138
HFC134a (R134a) system service tools .......... ATC-18
HFC134a system service equipment precaution ..........
ATC-13
High and low reverse clutch solenoid valve .... AT-162,
AT-164
Hood ................................................................... BL-13
Horn ................................................................. WW-59
HORN - Wiring diagram ................................... WW-59
HSEAT - Wiring diagram ................................... SE-98
I
IATS - Wiring diagram ....................... EC-205
, EC-911
ICC - Wiring diagram ....................................... ACS-20
ICC/BS - Wiring diagram ................. EC-590, EC-1264
ICC/SW - Wiring diagram ................ EC-576, EC-1249
ICCBOF - Wiring diagram ................ EC-681, EC-1371
Idle air volume learning ....................... EC-97, EC-787
Idle mixture ratio .............................................. EC-775
Idle speed .......................................... EC-769, EC-774
Idle speed control (ISC) .... EC-393, EC-395, EC-1125,
EC-1127
Ignition coil ....................................... EC-648, EC-1339
Ignition coil(VK45DE) ...................................... EM-189
Ignition coil(VQ35DE) ........................................ EM-42
Ignition control system ..................... EC-648, EC-1339
Ignition key hole illumination ............................. LT-155
Ignition timing .................................... EC-769, EC-774
IGNSYS - Wiring diagram ................ EC-649, EC-1340
Illumination control ............................................ LT-202
In vehicle sensor ........................... ATC-107, ATC-118
INF/D - Wring diagram ....................................... AV-63
INJECT - Wiring diagram ................. EC-662, EC-1352
Injector ............................................. EC-661, EC-1351
Input clutch solenoid valve ................. AT-150, AT-152
Instrument panel .................................................. IP-10
Intake air temperature sensor ........... EC-203, EC-223,
EC-909
, EC-930
Intake door control linkage adjustment ............ ATC-78
Intake door motor ............................ ATC-76, ATC-124
Intake manifold collector(VQ35DE) .................. EM-19
Intake manifold(VK45DE) ............................... EM-178
Intake manifold(VQ35DE) ................................. EM-24
Intake sensor ................................ ATC-113, ATC-120
Intake valve timing control (Bank 1) ... EC-174, EC-865
Intake valve timing control (Bank 2) ... EC-174, EC-865
Intake valve timing control position sensor (Bank 1) ....
EC-1166
Intake valve timing control position sensor (Bank 2) ....
EC-1166
Intake valve timing control solenoid valve (Bank 1) ......
EC-417
, EC-1141
Intake valve timing control solenoid valve (Bank 2) ......
EC-417
, EC-1141
Integrated homelink transmitter ....................... BL-235
Intelligent cruise control (ICC) system .............. ACS-6
Interior ................................................................. EI-36
Interior lamp ...................................................... LT-159
IPDM (Intelligent power distribution module engine
room) ................................................................. PG-18
IVCB1 - Wiring diagram ................... EC-418, EC-1142
IVCB2 - Wiring diagram ................... EC-420, EC-1144
IVCSB1 - Wiring diagram ............................... EC-1167
IVCSB2 - Wiring diagram ............................... EC-1169
IVIS (Infiniti vehicle immobilizer system) precautions ...
GI-3
IVTB1 - Wiring diagram ................................... EC-868
IVTB2 - Wiring diagram ................................... EC-870
K
Knock sensor (KS) ........................... EC-295
, EC-1031
KS - Wiring diagram ......................... EC-296, EC-1032
L
LAN system circuit ........................................... ATC-66
Lane Departure Warning System ....................... DI-82
Laser beam aiming adjustment ....................... ACS-12
Latch (lower anchors and tether for children) system ...
SB-9
LDW .................................................................... DI-82
LDW - Wiring Diagram ........................................ DI-95
Line pressure solenoid valve ........................... AT-129
Line pressure test (A/T) ..................................... AT-54
Liquid gasket application ......................... EM-6, LU-21
Liquid gasket application(VQ35DE) ........... LU-3, CO-3
Location of electrical units ................................. PG-70
Low coast brake solenoid valve ......... AT-166, AT-168
Low tire pressure warning system ...................... WT-7
Lubricant (R134a) A/C ..................................... ATC-27
Lubrication circuit (engine)(VK45DE) ................ LU-23
Lubrication circuit (engine)(VQ35DE) .................. LU-5
Lubrication oil A/C .......................................... ATC-162