warning INFINITI FX35 2005 Service Manual

IDX-8
ALPHABETICAL INDEX
Torque convertor clutch solenoid valve AT-125, AT-127
TPS1 - Wiring diagram .................... EC-280, EC-1017
TPS2 - Wiring diagram ...................... EC-215, EC-922
TPS3 - Wiring diagram .................... EC-635, EC-1318
Transfer control unit inspection table ................. TF-20
Transverse link (front) ...................................... FSU-14
TRNSCV - Wiring diagram ............................... BL-235
Trouble diagnoses .............................................. GI-11
Turbine revolution sensor ................................ AT-141
TURN - Wiring diagram ...................................... LT-96
Turn signal lamp ................................................. LT-91
Tyre pressure monitoring system - trouble diagnoses ..
WT-10
Tyre pressure monitoring system - wiring diagram .......
WT-11
U
Unified meter and A/C amp. ............................... DI-28
V
Vacuum hose (brake system) ............................ BR-18
Vacuum hose drawing (Engine control) ........... EC-120
Valve clearance(VK45DE) .............................. EM-219
Valve clearance(VQ35DE) ................................ EM-93
Valve guide ..................................................... EM-107
Valve guide(VK45DE) ..................................... EM-236
Valve lifter ......................................................... EM-88
Valve seat(VK45DE) ....................................... EM-238
Valve seat(VQ35DE) ...................................... EM-109
Valve spring(VK45DE) .................................... EM-239
Valve spring(VQ35DE) ................................... EM-110
Vanity mirror lamp ............................................. LT-151
Variable induction air control system (VIAS) EC-1292,
EC-1331
VDC -Wiring diagram ...................................... BRC-17
Vehicle security (theft warning) system ........... BL-186
Vehicle speed sensor (VSS) ........... EC-391, EC-1123,
EC-1288
VEHSEC - Wiring diagram ............................... BL-193
VENT/V - Wiring diagram EC-345, EC-570, EC-1078,
EC-1243
VIAS - Wiring diagram ................................... EC-1333
VIAS/V - Wiring diagram ................................ EC-1293
VIN registration .................................... EC-96, EC-786
W
WARN - Wiring diagram ..................................... DI-43
Warning chime .................................................... DI-58
Warning lamps .................................................... DI-42
Washer, front ..................................................... WW-4
Washer, rear .................................................... WW-38
Water control valve(VK45DE) ........................... CO-53
Water pump(VK45DE) ...................................... CO-51
Water pump(VQ35DE) ...................................... CO-22
Water temperature gauge ..................................... DI-5
Wheel alignment (front) ..................................... FSU-6
Wheel alignment (rear) ..................................... RSU-5
Wheel balance ....................................... WT-5, MA-33
Wheel bearing (front) .......................... FAX-4, FAX-10
Wheel bearing (rear) ......................................... RAX-5
Wheel hub (front) ................................ FAX-4, FAX-10
Wheel hub (rear) ............................................... RAX-5
Wheel sensor (VDC) ....................................... BRC-57
WINDOW - Wiring diagram .............................. GW-24
Window, door ...................................... GW-76, GW-80
Windshield ....................................................... GW-11
WIP/R - Wiring diagram ................................... WW-40
WIPER - Wiring diagram .................................. WW-11
Wiper, front ........................................................ WW-4
Wiper, rear ....................................................... WW-38
Wiring Diagram (Cell code) list ......................... PG-67
Wiring diagrams .................................................. GI-15
WT-T/WARN - Wiring diagram .......................... WT-11

IP-2
PRECAUTIONS
Revision: 2005 July 2005 FX
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
AIS003CB
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
PrecautionsAIS003CC

Disconnect both battery cables in advance.

Disconnect air bag system line in advance.

Never tamper with or force air bag lid open, as this may adversely affect air bag performance.

Be careful not to scratch pad and other parts.

When removing or disassembling any part, be careful not to damage or deform it. Protect parts, which
may get in the way with cloth.

When removing parts with a screwdriver or other tool, protect parts by wrapping them with vinyl or tape.

Keep removed parts protected with cloth.

If a clip is deformed or damaged, replace it.

If an unreusable part is removed, replace it with a new one.

Tighten bolts and nuts firmly to the specified torque.

After re-assembly has been completed, make sure each part functions correctly.

Remove stains in the following way.
Water-soluble stains:
Dip a soft cloth in warm water, and then squeeze it tightly. After wiping the stain, wipe with a soft dry cloth.
Oil stain:
Dissolve a synthetic detergent in warm water (density of 2 to 3% or less), dip the cloth, then clean off the stain
with the cloth. Next, dip the cloth in fresh water and squeeze it tightly. Then clean off the detergent completely.
Then wipe the area with a soft dry cloth.

Do not use any organic solvent, such as thinner or benzine.

PRECAUTIONS LAN-5
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2005 July 2005 FX
[CAN]PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
AKS00FCW
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions When Using CONSULT-IIAKS0058H
When connecting CONSULT-II to data link connector, connect them through CONSULT-II CONVERTER.
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
CHECK POINTS FOR USING CONSULT-II
1. Has CONSULT-II been used without connecting CONSULT-II CONVERTER on this vehicle?
–If YES, GO TO 2.
–If NO, GO TO 5.
2. Is there any indication other than indications relating to CAN communication system in the self-diagnosis results?
–If YES, GO TO 3.
–If NO, GO TO 4.
3. Based on self-diagnosis results unrelated to CAN communication, carry out the inspection.
4. Malfunctions may be detected in self-diagnosis depending on control units carrying out CAN communica- tion. Therefore, erase the self-diagnosis results.
5. Diagnose CAN communication system. Refer to LAN-7, "
TROUBLE DIAGNOSES WORK FLOW" .
Precautions For Trouble DiagnosisAKS0058I
CAN SYSTEM

Do not apply voltage of 7.0 V or higher to the measurement terminals.

Use the tester with its open terminal voltage being 7.0 V or less.

Be sure to turn ignition switch OFF and disconnect the battery cable from the negative terminal before
checking the circuit.

LAN-30
[CAN]
CAN COMMUNICATION
Revision: 2005 July 2005 FX
CAN COMMUNICATIONPFP:23710
System DescriptionAKS007GA
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitAKS007Z4
Go to CAN system, when selecting your CAN system type from the following table.
× : Applicable
TYPE 1/TYPE 2/TYPE 9
System Diagram

Ty p e 1
Body type Wagon
Axle 2WD AWD
Engine VQ35DE VQ35DE/VK45DE
Transmission A/T
Brake control VDC
Navigation system ×× ××
ICC system ×× ××
Intelligent Key system ×× ××
Lane departure warning system ×× ××
Automatic drive positioner ×××× ××××
CAN system type 9 1 2 3 4 10 5 6 7 8
CAN system trouble diagnosis LAN-
400LAN-47LAN-85LAN-
126
LAN-
171
LAN-
434
LAN-
219
LAN-
260
LAN-
304
LAN-
351
PKIB4203E

LAN-32
[CAN]
CAN COMMUNICATION
Revision: 2005 July 2005 FX
Ignition switch signal T R R
P range signal T R R
Stop lamp switch signal R T
Fuel consumption monitor signal TR
RT
Turbine revolution signal R T
Output shaft revolution signal R T R
A/C switch signal R T
A/C compressor request signal T R
A/C compressor feedback signal T R
Blower fan motor switch signal R T
A/C switch/indicator signal TR
RT
Cooling fan speed request signal T R
Position light request signal R T R R
Low beam request signal T R
Low beam status signal R T
High beam request signal T R R
High beam status signal R T
Front fog light request signal T R
Day time running light request
signal TR
Turn LED burnout status signal R T
Vehicle speed signal RR T
RRRR T R
Sleep wake up signal T R R
Door switch signal R T R R R
Turn indicator signal T R R
Key fob ID signal T R
Key fob door unlock signal T R
Oil pressure switch signal RT
TR
Buzzer output signal T R
Fuel level sensor signal R T
Fuel level low warning signal R T
ASCD SET lamp signal T R
ASCD CRUISE lamp signal T R
Malfunction indicator lamp signal T R
ASCD operation signal T R
ASCD OD cancel request signal T R Signals ECM TCM
Dis-
play unit BCM Steer-
ing
angle
sensor LDW
cam-
era unit Unified
meter and
A/C
amp. ABS
actua-
tor and elec-
tric unit (con-trol
unit) Driver
seat
control unit IPDM
E/R

CAN COMMUNICATION LAN-33
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2005 July 2005 FX
Front wiper request signal T R
Front wiper stop position signal R T
Rear window defogger switch sig-
nal TR
Rear window defogger control
signal RRR T
Hood switch signal R T
Theft warning horn request signal T R
Horn chirp signal T R
Steering angle sensor signal T R
ABS warning lamp signal RT
VDC OFF indicator lamp signal R T
SLIP indicator lamp signal RT
Brake warning lamp signal RT
System setting signal TR R
RT T
A/T CHECK indicator lamp signal T R
A/T position indicator lamp signal T R
A/T shift schedule change
demand signal RT
Manual mode signal R T
Not manual mode signal R T
Manual mode shift up signal R T
Manual mode shift down signal R T
Manual mode indicator signal T R
Distance to empty signal R T
Parking brake switch signal R T
Snow mode switch signal R T
Tire pressure signal T R Signals ECM TCM
Dis-
play unit BCM St e e r-
ing
angle
sensor LDW
cam-
era unit Unified
meter and
A/C
amp. ABS
actua-
tor and elec-
tric unit (con-trol
unit) Driver
seat
control unit IPDM
E/R

LAN-36
[CAN]
CAN COMMUNICATION
Revision: 2005 July 2005 FX
Vehicle speed signal RRRT
RRRRR TRR
Sleep wake up signal TR R
TR
Door switch signal R R T R R R
Turn indicator signal T R R
Key fob ID signal T R
Key fob door unlock sig-
nal TR
Oil pressure switch sig-
nal RT
TR
Buzzer output signal TR
TR
TR
Fuel level sensor signal R T
Fuel level low warning
signal RT
Malfunctioning indicator
lamp signal TR
ICC operation signal R T
Front wiper request sig-
nal RT R
Front wiper stop position
signal RT
Rear window defogger
switch signal TR
Rear window defogger
control signal RR R T
Hood switch signal R T
Theft warning horn
request signal TR
Horn chirp signal T R
Steering angle sensor
signal TR
Tire pressure signal T R
ABS warning lamp signal R T
VDC OFF indicator lamp
signal RT
SLIP indicator lamp sig-
nal RT
Brake warning lamp sig-
nal RT
Signals ECM TCM
Dis-
play
con-
trol
unit ICC
unit Intelli-
gent Key unit BCM St e e r-
ing
angle
sen- sor LDW
cam- era
unit Uni-
fied
meter and
A/C
amp. ICC
sen-
sor ABS
actu- ator and
elec- tric
unit
(con- trol
unit) Driver
seat
con-
trol
unit IPDM
E/R

CAN COMMUNICATION LAN-37
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2005 July 2005 FX
System setting signal TR R
RT T
Distance to empty signal R T
Parking brake switch sig-
nal RT
Door lock/unlock request
signal TR
Door lock/unlock status
signal RT
Starter permission signal T R
Back door open request
signal TR
Power window open
request signal TR
Alarm request signal T R
Key warning signal T R
ICC sensor signal R T
ICC warning lamp signal T R
ICC system display sig-
nal TR
Current gear position sig-
nal TR R
ICC steering switch sig-
nal TR
ASCD operation signal T R
ASCD OD cancel
request signal TR
ICC OD cancel request
signal RT
A/T CHECK indicator
lamp signal TR
A/T position indicator
lamp signal TR
A/T shift schedule
change demand signal R
T
Manual mode signal R T
Not manual mode signal R T
Manual mode shift up
signal RT
Manual mode shift down
signal RT
Manual mode indicator
signal TR R
Signals ECM TCM
Dis-
play
con-
trol
unit ICC
unit Intelli-
gent Key unit BCM Ste er-
ing
angle
sen- sor LDW
cam- era
unit Uni-
fied
meter and
A/C
amp. ICC
sen-
sor ABS
actu- ator and
elec- tric
unit
(con- trol
unit) Driver
seat
con-
trol
unit IPDM
E/R

LAN-40
[CAN]
CAN COMMUNICATION
Revision: 2005 July 2005 FX
A/C switch/indicator signal TR
RT
Cooling fan speed request sig-
nal T
R
Position light request signal R T R R
Low beam request signal T R
Low beam status signal R T
High beam request signal T R R
High beam status signal R T
Front fog light request signal T R
Day time running light request
signal TR
Turn LED burnout status signal R T
Vehicle speed signal RRRT
RRR R T R
Sleep wake up signal T R R
Door switch signal R T R R R
Turn indicator signal T R R
Key fob ID signal T R
Key fob door unlock signal T R
Oil pressure switch signal RT
TR
Buzzer output signal T R
Fuel level sensor signal R T
Fuel level low warning signal R T
ASCD SET lamp signal T R
ASCD CRUISE lamp signal T R
Malfunction indicator lamp sig-
nal TR
Front wiper request signal T R
Front wiper stop position signal R T
Rear window defogger switch
signal TR
Rear window defogger control
signal RRR T
Hood switch signal R T
Theft warning horn request sig-
nal TR
Horn chirp signal T R
Steering angle sensor signal T R Signals ECM TCM
Dis-
play
unit AW D
con- trol
unit BCM Steer-
ing
angle
sensor LDW
cam- era
unit Uni-
fied
meter and
A/C
amp. ABS
actua- tor
and
elec- tric
unit
(con- trol
unit) Driver
seat
con-
trol
unit IPDM
E/R

CAN COMMUNICATION LAN-41
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2005 July 2005 FX
*: VK45DE engine model only ABS warning lamp signal
RT
VDC OFF indicator lamp signal R T
SLIP indicator lamp signal RT
Brake warning lamp signal RT
System setting signal TR R
RT T
AWD warning lamp signal T R
Distance to empty signal R T
Parking brake switch signal R R T
ASCD operation signal T R
ASCD OD cancel request signal T R
A/T CHECK indicator lamp sig-
nal TR
A/T position indicator lamp sig-
nal TR
A/T shift schedule change
demand signal RT
Manual mode signal R T
Not manual mode signal R T
Manual mode shift up signal R T
Manual mode shift down signal R T
Manual mode indicator signal T R
Snow mode switch signal R T
Current gear position signal* R T
Next gear position signal* R T
Shift change signal* R T
Shift pattern signal* R T
Tire pressure signal T R Signals ECM TCM
Dis-
play
unit AWD
con- trol
unit BCM Steer-
ing
angle
sensor LDW
cam- era
unit Uni-
fied
meter and
A/C
amp. ABS
actua- tor
and
elec- tric
unit
(con- trol
unit) Driver
seat
con-
trol
unit IPDM
E/R