turn signal INFINITI FX35 2005 Manual PDF

AUDIO AV-37
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
Terminals and Reference Value for WooferAKS00AM2
A/C and AV Switch Self-Diagnosis FunctionAKS007OE
It can check ON/OFF operation of each switch in the A/C and AV switch and diagnose the input signals to the
audio steering wheel switch.
STARTING THE SELF-DIAGNOSIS MODE
1. Turn ignition switch from OFF to ACC.
2. Within 10 seconds press and hold the switches “MUTE/ II ” and
“MAP ”simultaneously for 3 seconds.
Then the self-diagnosis operates.
EXITING THE SELF-DIAGNOSIS MODE

Turn ignition switch OFF. Then the self-diagnosis ends.
DIAGNOSIS FUNCTION

It can illuminate all the indicators (LED) in the A/C and AV switch.

It can check for continuity of the switches by sounding the buzzer when the A/C and AV switch is pressed.

It can check for continuity of harness between A/C and AV switch and audio steering wheel switch.
Terminal No. (Wire color) Item Signal
input/
output Condition
Voltag e Example of
symptom
+– Ignition
switch Operation
1 (G/R) Ground Battery power
Supply Input OFF — Battery voltage No sound from
woofer.
2 (B) Ground Ground — ON — Approx. 0 V No sound from
woofer.
5 (P) Ground Amp ON signal Input ACC — Approx. 12 V No sound from
woofer.
7 (W) 8 (B) Woofer sound
signal Input ACC Receive audio sig-
nal No sound from
woofer.
SKIA0177E
PKIB4130E

AUDIO AV-45
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
2. CHECK AMP. ON SIGNAL
1. Connect audio unit connector.
2. Turn the ignition switch ACC.
3. Check voltage between audio unit harness connector M59 ter- minal 12 (G/W) and ground.
OK or NG
OK >> INSPECTION END (System is OK.)
NG >> Replace audio unit.
Vehicle Speed Signal InspectionAKS007VI
1. CHECK VEHICLE SPEED OPERATION
Start engine and drive vehicle.
Dose speedometer is operated normally?
Ye s > > G O T O 2 .
No >> Check combination meter trouble diagnosis. Refer to DI-15, "
Trouble Diagnosis" .
2. CHECK HARNESS
1. Turn the ignition switch OFF.
2. Disconnect audio unit connector and unified meter and A/C amp. connector.
3. Check continuity between audio unit harness connector M60 ter- minal 22 (W/L) and unified meter and A/C amp. harness connec-
tor M56 terminal 34 (W/L).
4. Check continuity between audio unit harness connector M60 ter- minal 22 (W/L) and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector. 12 (G/W) – Ground : Approx. 12 V
SKIA6818E
22 (W/L) – 34(W/L) : Continuity should exist.
22 (W/L) – Ground : Continuity should not exist.
SKIA6807E

AV-46
AUDIO
Revision: 2005 July 2005 FX
3. CHECK VEHICLE SPEED SIGNAL
1. Connect unified meter and A/C amp. connector.
2. Start engine and drive vehicle at more than 40 km/h (25MPH).
3. Check the signal between audio unit harness connector M60 terminal 22 (W/L) and ground with CON- SULT-ll or oscilloscope.
OK or NG
OK >> INSPECTION END (System is OK.)
NG >> Replace unified meter and A/C amp.
Locking CD Auto-Changer MechanismAKS007GD
CAUTION:

Prior to removing a malfunctioning CD auto-changer unit that will be shipped for repair, the
changer mechanism MUST BE LOCKED to prevent the mechanism from being damaged during
shipping.

If a CD is jammed or unable to be removed from the unit, do NOT lock the changer mechanism. If
the unit is to be shipped for repair, carefully package the unit to prevent vibration and shock.
DAMPER LOCK PROCEDURE
1. Eject and remove any CDs from the audio unit.
2. Turn ignition switch OFF. Wait until audio unit display is off and mechanism stops moving (mechanism sound stops).
3. Press any one of the disc selection buttons once. When a display shows on the audio unit, press the same disc selection button again within 5 seconds.

The changer mechanism will lock itself within 10 seconds.
4. After mechanism stops moving (mechanism sound stops), open the driver and passenger window, and then disconnect negative battery cable.
NOTE:
After installing a new or remanufactured audio unit, switching the audio unit ON will automatically unlock the
mechanism. A special unlocking procedure is not required.
Terminal Condition Reference
signal
(+) (–)
22
(W/L) Ground When vehicle
speed is approx.40
km/h (25MPH)
SKIA6809EELF1080D

AUDIO ANTENNA AV-51
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
AUDIO ANTENNAPFP:28200
System DescriptionAKS007WE
With the ignition switch in ACC or ON, power is supplied

through 10A fuse [No. 6, located in the fuse block (J/B)]

to audio unit terminal 10.
Ground is supplied through the case of the antenna amp.
When the radio switch is turned ON, antenna signal is supplied

through audio unit terminal 5

to the antenna amp.
Then the antenna amp. is activated.
The amplified radio signals are supplied to the audio unit through the antenna amp.

AUDIO ANTENNA AV-53
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
Terminals and Reference Value for Audio UnitAKS007WW
Antenna Amp. InspectionAKS007WX
1. CHECK ANTENNA FEEDER
Check with visual observation if antenna feeder between audio unit and antenna amp. has disconnection or
malfunction on the mounting part (engagement, looseness of shield earth, etc.).
OK or NG
OK >> GO TO 2
NG >> Replace antenna feeder.
2. CHECK ANTENNA SIGNAL
1. Turn the ignition switch ACC.
2. Check voltage between audio unit harness connector M58 ter- minal 5 (R/W) and ground.
OK or NG
OK >> INSPECTION END (System is OK.)
NG >> Replace audio unit.
Terminal
(Wire color) Item Signal
input/
output Condition
Reference value Example of
symptom
+– Ignition
switch Operation
5 (R/W) Ground Antenna signal Input ACC — Approx. 12 V Receiving status of radio
broadcast becomes bad.
10 (LG/R) Ground ACC power
supply Input ACC — Battery voltage
System does not work
properly.
5 (R/W) – Ground : Approx. 12 V
SKIA6854E

AV-60
INTEGRATED DISPLAY SYSTEM
Revision: 2005 July 2005 FX
SETTING SCREEN

Setting of electric status can be changed by A/C and AV switch. The signal is sent to BCM through display
unit to change vehicle electric system setting.

Display unit is communicating with driver seat control unit.

Pressing “SETTING” switch once cycles display from DISPLAY →LANGUAGE →BEEP SET →SERVICE
ALERT →PERSONALIZED SETTINGS MENU →DISPLAY OFF →DISPLAY.

Using the joystick, setting of each item will become possible.
Adjustable Vehicle Status
NOTE:
Setting in factory shipment is ON. Setting items
Setting
variations Initial
setting Operation
DISPLAY ON/OFF ON It switches displayed/Non-displayed of the screen.
LANGUAGE ENGLISH/
FRANCAIS – It switches displayed language.
BEEP SET ON/OFF ON It selects beep sound ON/OFF during switch operation. How-
ever, even if beep is set OFF, beep for NO OPERATION and
for screen interception are not reset.
SERVICE ALERT ON/OFF OFF It switches displayed/Non-displayed of alert indication.

When the setting is ON, if engine oil or tire rotation will be
replace distance, alert is displayed.

When the setting is OFF, alert is not displayed.
PERSONALIZED
SETTING MENU SLIDE BACK DR
SEAT ON EXIT ON/OFF
ON
NOTEThe driver’s seat automatically moves back and returns to the
original position for exceptional ease of exit and entry. (Models
with automatic drive positioner.)
LIFT STEERING
WHEEL ON EXIT ON/OFF
ON
NOTEThe steering column automatically tilts up and returns to the
original position for exceptional ease of entry and exit. (Models
with automatic drive positioner.)
REMOTE UNLOCK
DOOR LOGIC DR-1ST/ALL DR-1ST This key can switch the unlock doors of the 1st unlocking oper-
ation as follows:

Only the driver side door ⇔All the doors
HORN CHIRP
WITH REMOTE ON/OFF ON This key changes the horn chirp mode occurring when pressing
the LOCK button on the keyfob.
LAMPS FLASH
WITH REMOTE ALL/LOCK/
UNLOCK/OFF ALLThis key changes the hazard indicator flash mode occurring
when pressing the LOCK or UNLOCK button on the keyfob.
AUTO RE-LOCK
TIME 5m/1m/OFF 1m The length of auto door re-lock time can be set. Select the
“Auto Re-Lock timer” key, then move the joystick to adjust the
time.
AUTO HEADLAMP
SENSITIVITY LEVEL 1/2/3/4 LEVEL 2 Automatic light illumination can be set as desired. Select the
“Auto Headlamp Sensitivity” key, then move the joystick to the
left (lower) or right (higher).
AUTO HEADLAMP
OFF DELAY OFF/30/45/60/
90/120/150/ 180 SEC 45 SEC This key can control how long it takes the automatic turn off
timer to extinguish the headlamps in “AUTO” position. Select
the “Auto Headlamp Off Delay” key, then move the joystick to
the left or right to adjust the timer.
SPEED SENSING
WIPER INTERVAL ON/OFF ON This key turns on and off the driving speed dependent intermit-
tent wiper function.
CONFIRM RESET
SETTINGS YES/NO NO When this key is selected and turned on using the “ENTER”
button, all settings mode by PERSONALIZED SETTINGS will
return to the initial conditions.

INTEGRATED DISPLAY SYSTEM AV-61
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
D/N SCREEN

Turning on “DAY/NIGHT” switch, DAY MODE or NIGHT MODE
is indicated for present mode.

If press “DAY/NIGHT” again when display adjustment lumi-
nance, change DAY-NIGHT (NIGHT-DAY) mode (screen of
adjustment luminance).
As follows:

Press “PREV” or not operate for 10sec. when displayed screen
of adjustment luminance, back to default screen (same mode).

Can adjust luminance by “DISP” switch. Light can be adjusted by pressing “+” (bright) or “–” (dark).

Adjustment range is a 12 stage (MIN to MAX) and default set value is 10 (DAY) and 4 (NIGHT).
WARNING INDICATIONS
When BCM receives warning signal from some control units or sensors, then combination meter warning lamp
is illuminated.
Then BCM sends warning signal to display unit warning indications on the screen.
AV COMMUNICATION LINE
Display unit is controlled by the following unit with AV communication line.

A/C and AV switch
CAN Communication System DescriptionAKS007Z5
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitAKS007YZ
Refer to LAN-30, "CAN Communication Unit" .
Component Parts and Harness Connector Location AKS005U2
NOW Change display
DAY DAY →NIGHT →DAY →·····
NIGHT NIGHT →DAY →NIGHT →·····
SKIA5920E
Warning indicators Warning lamps in
instrument panel Warning detection and cancel conditions Cases of malfunction
DOOR OPEN Door Detection
condition Vehicle is running [approx. 3.5 km/h (2 MPH) or
faster] and door ajar of any of the doors is detected. Door is open.
Cancel
condition Vehicle is stopped and all the doors close.
SKIA4970E

AV-72
INTEGRATED DISPLAY SYSTEM
Revision: 2005 July 2005 FX
Terminals and Reference Value for Display UnitAKS005U6
Terminal No.
(Wire color) Item Signal
input/
output Condition
Voltage Example of
symptom
+– Ignition
switch Operation
1 (W/L) Ground Battery power
supply Input OFF — Battery voltage System does not
work properly.
2 (LG/R) Ground ACC power
supply Input ACC — Battery voltage System does not
work properly.
3 (G/R) Ground Ignition signal Input ON — Battery voltage A/C operation is
not possible.
Vehicle informa-
tion setting is not possible.
4 (R/L) Ground Illumination
signal Input OFF Lighting switch is
ON (1st position). Approx. 12 V Audio unit illumi-
nation does not
come on when
lighting switch is
ON (1st position).
Turn lighting
switch OFF. Approx. 0 V
6 (B) Ground Ground — ON — Approx. 0 V —
7 (R/G) Ground Vehicle speed
signal (8-pulse) Input ON When vehicle
speed is approx.
40 km/h (25 MPH) Drive computer
item is not dis-
played correctly.
8 (LG) Ground Audio TX
(DSP-AUD) Output ON
Operate audio
volume. Audio does not
operate properly.
9 — Shield ground — — — — —
10 (B/Y) Ground Audio RX
(AUD-DSP) Input ON
Operate audio
volume. Audio does not
operate properly.
11 (B/R) Ground Communica-
tion signal (+) Input/
output ON — System does not
work properly.
12 — Shield ground — — — — —
PKIA1935E
SKIA4402E
SKIA4403E
SKIA0175E

AV-74
INTEGRATED DISPLAY SYSTEM
Revision: 2005 July 2005 FX
On Board Self-Diagnosis FunctionAKS005U8
DESCRIPTION

Diagnosis function consists of the self-diagnosis mode performed automatically.

Self-diagnosis mode checks for connections between the units constituting this system, analyzes each
individual unit at the same time, and displays the results on the LCD screen.
DIAGNOSIS ITEM
Self-Diagnosis ModeAKS005U9
OPERATION PROCEDURES
1. Start the engine.
2. Turn the audio system off.
3. While pressing the “MUTE/ II ” switch, turn the volume control
dial clockwise or counterclockwise for 30 clicks or more. (When
the self-diagnosis mode is started, a short beep will be heard.)
4. Display unit connection check screen.
5. Select each connecting unit (CHANGER, SATELLITE RADIO).
13 (G/W) Ground Steering SW
B Input ON Press POWER
switch. Approx. 0 V
Audio steering
wheel switches
do not function.
Press SEEK
DOWN switch. Approx. 1.7 V
Press VOL DOWN
switch. Approx. 3.3 V
Except for above Approx. 5 V
14 (B/Y) — Steering SW
ground —— — — Audio steering
wheel switches
do not function.
Terminal No.
(Wire color) Item Signal
input/
output Condition
Voltage Example of
symptom
+– Ignition
switch Operation
Mode Item Description Reference page
Self-diagnosis NETWORK CHECK
Check network between control unit and switch connected
from display unit via communication line. AV-75, "
NETWORK CHECK"
PARTS CHECK
Perform diagnosis and setting of display unit.

Perform self-diagnosis for auto air conditioner system. AV- 7 5 , "PARTS CHECK"
VERSION CHECK Displays version of each unit.
AV- 7 6 , "VERSION CHECK"
CAN DIAG MNTR Display unit displays CAN communication status. AV- 7 6 , "CAN DIAG MNTR
(CAN DIAG MONITOR)"
PKIB4131E
SKIA5921E

INTEGRATED DISPLAY SYSTEM AV-77
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
A/C and AV Switch Self-Diagnosis FunctionAKS005UA
It can check ON/OFF operation of each switch in the A/C and AV switch and diagnose the input signals to the
steering switch (audio).
STARTING THE SELF-DIAGNOSIS MODE
1. Turn ignition switch from OFF to ACC.
2. Within 10 seconds press and hold the switches “MUTE/ II ” and
“PREV ”simultaneously for 3 seconds.
Then the self-diagnosis operates.
EXITING THE SELF-DIAGNOSIS MODE
Turn ignition switch OFF. Then the self-diagnosis ends.
DIAGNOSIS FUNCTION

It can illuminate all the indicators (LED) in the A/C and AV switch.

It can check for continuity of the switches by sounding the buzzer when the A/C and AV switch is pressed.

It can check for continuity of harness between A/C and AV switch and steering switch (audio).
SKIA4972E