Exterior INFINITI FX35 2006 User Guide
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2006, Model line: FX35, Model: INFINITI FX35 2006Pages: 4462, PDF Size: 57.74 MB
Page 3564 of 4462
LT-2Revision: 2006 December 2006 FX35/FX45 Preliminary Check ...............................................
... 49
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................. ... 49
INSPECTION PARKING BRAKE SWITCH CIR-
CUIT ................................................................. ... 50
CONSULT-II Functions (BCM) ............................. ... 51
CONSULT-II BASIC OPERATION .................... ... 51
DATA MONITOR ............................................... ... 51
ACTIVE TEST .................................................. ... 52
Daytime Light Control Does Not Operate Properly ... 53
Aiming Adjustment ............................................... ... 55
Bulb Replacement ............................................... ... 55
Removal and Installation ..................................... ... 55
Disassembly and Assembly ................................. ... 55
AUTO LIGHT SYSTEM .......................................... ... 56
Component Parts and Harness Connector Location ... 56
System Description .............................................. ... 56
OUTLINE .......................................................... ... 56
COMBINATION SWITCH READING FUNCTION ... 57
DELAY TIMER FUNCTION .............................. ... 57
CAN Communication System Description ........... ... 57
CAN Communication Unit .................................... ... 57
Major Components and Functions ....................... ... 57
Schematic ............................................................ ... 58
Wiring Diagram — AUTO/L — ............................. ... 59
Terminals and Reference Values for BCM ........... ... 62
Terminals and Reference Values for IPDM E/R ... ... 63
How to Proceed With Trouble Diagnosis ............. ... 63
Preliminary Check ............................................... ... 64
SETTING CHANGE FUNCTIONS .................... ... 64
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................. ... 64
CONSULT-II Functions (BCM) ............................. ... 66
CONSULT-II BASIC OPERATION .................... ... 66
WORK SUPPORT ............................................ ... 66
DATA MONITOR ............................................... ... 66
ACTIVE TEST .................................................. ... 68
CONSULT-II Functions (IPDM E/R) ..................... ... 68
CONSULT-II BASIC OPERATION .................... ... 68
DATA MONITOR ............................................... ... 68
ACTIVE TEST .................................................. ... 69
Symptom Chart .................................................... ... 69
Lighting Switch Inspection ................................... ... 69
Optical sensor System Inspection ....................... ... 70
Removal and Installation of Optical Sensor ......... ... 72
REMOVAL ........................................................ ... 72
INSTALLATION ................................................. ... 72
HEADLAMP AIMING CONTROL ........................... ... 73
Schematic ............................................................ ... 73
Wiring Diagram — H/AIM — ................................ ... 74
Removal and Installation ..................................... ... 77
REMOVAL ........................................................ ... 77
INSTALLATION ................................................. ... 77
Switch Circuit Inspection ..................................... ... 77
FRONT FOG LAMP ............................................... ... 78
Component Parts and Harness Connector Location ... 78
System Description .............................................. ... 78
OUTLINE .......................................................... ... 78
FRONT FOG LAMP OPERATION .................... ... 79 COMBINATION SWITCH READING FUNCTION
... 79
EXTERIOR LAMP BATTERY SAVER CONTROL ... 79
CAN Communication System Description ........... ... 79
CAN Communication Unit .................................... ... 79
Wiring Diagram — F/FOG — ............................... ... 80
Terminals and Reference Values for BCM ........... ... 82
Terminals and Reference Values for IPDM E/R ... ... 82
How to Proceed With Trouble Diagnosis ............. ... 83
Preliminary Check ................................................ ... 83
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................. ... 83
CONSULT-II Functions (BCM) ............................. ... 84
CONSULT-II Functions (IPDM E/R) ..................... ... 84
Front Fog Lamps Do Not Illuminate (Both Sides) ... 85
Front Fog Lamp Does Not Illuminate (One Side) . ... 87
Aiming Adjustment ............................................... ... 88
Bulb Replacement ................................................ ... 89
Removal and Installation ...................................... ... 89
REMOVAL ......................................................... ... 89
INSTALLATION ................................................. ... 89
TURN SIGNAL AND HAZARD WARNING LAMPS ... 90
Component Parts and Harness Connector Location ... 90
System Description .............................................. ... 90
TURN SIGNAL OPERATION ............................ ... 90
HAZARD LAMP OPERATION .......................... ... 91
REMOTE CONTROL ENTRY SYSTEM OPER-
ATION ............................................................... ... 92
COMBINATION SWITCH READING FUNCTION ... 93
CAN Communication System Description ........... ... 93
CAN Communication Unit .................................... ... 93
Schematic ............................................................ ... 94
Wiring Diagram — TURN — ................................ ... 95
Terminals and Reference Values for BCM ........... ... 98
Terminals and Reference Value for Rear Combina-
tion Lamp Control Unit ......................................... ... 99
How to Proceed With Trouble Diagnosis ............. .102
Preliminary Check ................................................ .102
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................. .102
CONSULT-II Functions (BCM) ............................. .104
CONSULT-II BASIC OPERATION .................... .104
DATA MONITOR ............................................... .104
ACTIVE TEST ................................................... .104
Turn Signal Lamp Does Not Operate ................... .105
Rear Turn Signal Lamp Does Not Operate .......... .106
Hazard Warning Lamp Does Not Operate But Turn
Signal Lamp Operate ........................................... .108
Bulb Replacement (Front Turn Signal Lamp) ....... .110
Bulb Replacement (Rear Turn Signal Lamp) ....... .110
Removal and Installation of Front Turn Signal Lamp .110
Removal and Installation of Rear Turn Signal Lamp .110
Removal and Installation of Rear Combination
Lamp Control Unit ................................................ .110
REMOVAL ......................................................... .110
INSTALLATION ................................................. .110
LIGHTING AND TURN SIGNAL SWITCH ............. . 111
Removal and Installation ...................................... . 111
REMOVAL ......................................................... . 111
INSTALLATION ................................................. . 111
Page 3565 of 4462
LT-3
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2006 December 2006 FX35/FX45 HAZARD SWITCH .................................................
..112
Removal and Installation ..................................... .. 112
REMOVAL ........................................................ .. 112
INSTALLATION ................................................ .. 112
COMBINATION SWITCH ....................................... ..113
Wiring Diagram — COMBSW — ......................... .. 113
Combination Switch Reading Function ............... .. 114
Terminals and Reference Values for BCM .......... .. 114
CONSULT-II Functions (BCM) ............................ .. 119
CONSULT-II BASIC OPERATION .................... .. 119
DATA MONITOR .............................................. .. 119
Combination Switch Inspection ........................... . 120
Removal and Installation ..................................... . 122
STOP LAMP .......................................................... . 123
Component Parts and Harness Connector Location . 123
System Description ............................................. . 123
Schematic ........................................................... . 124
Wiring Diagram — STOP/L — ............................. . 125
Terminals and Reference Value for Rear Combina-
tion Lamp Control Unit ........................................ . 128
Stop Lamp Does Not Operate ............................. . 128
High-Mounted Stop Lamp ................................... . 130
BULB REPLACEMENT, REMOVAL AND
INSTALLATION ................................................ . 130
Stop Lamp ........................................................... . 130
BULB REPLACEMENT .................................... . 130
REMOVAL AND INSTALLATION ..................... . 130
Rear Combination Lamp Control Unit ................. . 130
REMOVAL AND INSTALLATION ..................... . 130
BACK-UP LAMP ................................................... . 131
Wiring Diagram — BACK/L — ............................ . 131
Bulb Replacement ............................................... . 132
Removal and Installation ..................................... . 132
PARKING, LICENSE PLATE AND TAIL LAMPS .. . 133
Component Parts and Harness Connector Location . 133
System Description ............................................. . 133
OUT LINE ......................................................... . 133
OPERATION BY LIGHTING SWITCH ............. . 134
COMBINATION SWITCH READING FUNCTION . 135
EXTERIOR LAMP BATTERY SAVER CONTROL . 135
CAN Communication System Description ........... . 135
CAN Communication Unit ................................... . 135
Schematic ........................................................... . 136
Wiring Diagram — TAIL/L — ............................... . 137
Terminals and Reference Values for BCM .......... . 142
Terminals and Reference Values for IPDM E/R .. . 142
Terminals and Reference Value for Rear Combina-
tion Lamp Control Unit ........................................ . 144
How to Proceed With Trouble Diagnosis ............. . 144
Preliminary Check ............................................... . 144
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................. . 144
CONSULT-II Functions (BCM) ............................ . 145
CONSULT-II Functions (IPDM E/R) .................... . 145
Parking, License Plate and Side Marker Lamps Do
Not Illuminate ...................................................... . 145
Tail Lamp Does Not Operate ............................... . 151
Parking, License Plate, Side Maker and Tail Lamps
Do Not Turn OFF (After Approx. 10 Minutes) ...... . 152 License Plate Lamp .............................................
.152
BULB REPLACEMENT, REMOVAL AND
INSTALLATION ................................................ .152
Front Parking Lamp ............................................. .153
BULB REPLACEMENT .................................... .153
REMOVAL AND INSTALLATION ..................... .153
Tail Lamp ............................................................. .153
BULB REPLACEMENT .................................... .153
REMOVAL AND INSTALLATION ..................... .153
Front Side Marker Lamp ...................................... .153
BULB REPLACEMENT .................................... .153
REMOVAL AND INSTALLATION ..................... .153
Rear Side Marker Lamp ...................................... .153
BULB REPLACEMENT .................................... .153
REMOVAL AND INSTALLATION ..................... .153
Rear Combination Lamp Control Unit .................. .153
REMOVAL AND INSTALLATION ..................... .153
REAR COMBINATION LAMP ................................ .154
Bulb Replacement ............................................... .154
REAR FENDER SIDE (REAR SIDE MARKER
LAMP BULB) .................................................... .154
BACK DOOR SIDE (BACK-UP LAMP) ............ .154
Removal and Installation ..................................... .154
REMOVAL ........................................................ .154
INSTALLATION ................................................ .155
INTERIOR ROOM LAMP ....................................... .156
Component Parts and Harness Connector Location .156
System Description .............................................. .156
POWER SUPPLY AND GROUND ................... .157
SWITCH OPERATION ..................................... .158
ROOM LAMP TIMER OPERATION ................. .159
INTERIOR LAMP BATTERY SAVER CONTROL .160
Schematic ............................................................ .162
Wiring Diagram — ROOM/L — ........................... .164
Terminals and Reference Values for BCM ........... .172
How to Proceed With Trouble Diagnosis ............. .173
Preliminary Check ............................................... .173
CHECK FOR POWER SUPPLY AND GROUND
CIRCUIT ........................................................... .173
CONSULT-II Functions (BCM) ............................. .174
CONSULT-II BASIC OPERATION .................... .174
WORK SUPPORT (INT LAMP) ........................ .174
DATA MONITOR (INT LAMP) .......................... .174
ACTIVE TEST (INT LAMP) .............................. .175
WORK SUPPORT (BATTERY SAVER) ........... .176
DATA MONITOR (BATTERY SAVER) .............. .176
ACTIVE TEST (BATTERY SAVER) .................. .177
Interior Room Lamp Control Does Not Operate .. .177
Map Lamp Control Does Not Operate ................. .178
Personal Lamp Control Does Not Operate .......... .181
Ignition Key Hole Illumination Control Does Not
Operate ................................................................ .182
All Step Lamps Do Not Operate .......................... .184
All Interior Room Lamps Do Not Operate ............ .185
Bulb Replacement ............................................... .185
IGNITION KEY HOLE ILLUMINATION (WITH-
OUT INTELIGENT KEY) .................................. .185
IGNITION KEY HOLE ILLUMINATION (WITH
INTELIGENT KEY) ........................................... .185
Page 3566 of 4462
LT-4Revision: 2006 December 2006 FX35/FX45 FRONT STEP LAMP ........................................
.186
REAR STEP LAMP .......................................... .186
LUGGAGE ROOM LAMP ................................. .186
VANITY MIRROR LAMP .................................. .186
MAP LAMP ....................................................... .187
INTERIOR ROOM LAMP ................................. .187
PERSONAL LAMP ........................................... .187
Removal and Installation ..................................... .187
LUGGAGE ROOM LAMP ................................. .187
MAP LAMP ....................................................... .188
INTERIOR ROOM LAMP ................................. .188
PERSONAL LAMP ........................................... .188
ILLUMINATION ...................................................... .189
System Description .............................................. .189
ILLUMINATION OPERATION BY LIGHTING
SWITCH ........................................................... .189 EXTERIOR LAMP BATTERY SAVER CONTROL
.190
CAN Communication System Description ........... .191
CAN Communication Unit .................................... .191
Schematic ............................................................ .192
Wiring Diagram — ILL — ..................................... .194
Bulb Replacement ................................................ .203
GLOVE BOX LAMP .......................................... .203
A/T DEVICE ILLUMINATION ............................ .203
COIN BOX ILLUMINATION .............................. .203
Removal and Installation ...................................... .203
ILLUMINATION CONTROL SWITCH ............... .203
BULB SPECIFICATIONS ....................................... .204
Headlamp ............................................................. .204
Exterior Lamp ....................................................... .204
Interior Lamp/Illumination ..................................... .204
Page 3571 of 4462
HEADLAMP - XENON TYPE - LT-9
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2006 December 2006 FX35/FX45
Ground is supplied
to front combination lamp RH and LH terminals 7
through grounds E21, E50 and E51,
With power and ground supplied, the high beam headlamps illuminate.
If voltage is applied to a high beam solenoid, the bulb shade will move, even a xenon head lamp bulb comes
out, and a high beam and a low beam are changed.
The unified meter and A/C amp. that received the high beam request signal by BCM through the CAN commu-
nication makes a high beam indicator lamp turn on in combination meter.
COMBINATION SWITCH READING FUNCTION
Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" .
EXTERIOR LAMP BATTERY SAVER CONTROL
When the combination switch (lighting switch) is in the 2ND position (ON), and the ignition switch is turned
from ON or ACC to OFF, the battery saver control function is activated.
Under this condition, the headlamps remain illuminated for 5 minutes, then the headlamps are turned OFF.
Exterior lamp battery saver control mode can be changed by the function setting of CONSULT-II.
AUTO LIGHT OPERATION (IF EQUIPPED)
Refer to LT- 5 6 , "System Description" .
VEHICLE SECURITY SYSTEM
The vehicle security system will flash the high beams if the system is triggered. Refer to BL-180, "VEHICLE
SECURITY (THEFT WARNING) SYSTEM" .
XENON HEADLAMP
Xenon type lamps are used for to the low beam headlamps. Xenon bulbs do not use a filament. Instead, they
produce light when a high voltage current is passed between two tungsten electrodes through a mixture of
xenon (an inert gas) and certain other metal halides. In addition to strong lighting power, electronic control of
the power supply gives the headlamps stable quality and tone color.
Followings are some advantages of the xenon type headlamp.
The light produced by the headlamps is white color similar to sunlight that is easy to the eyes.
Light output is nearly double that of halogen headlamps, affording increased area of illumination.
Retroreflected luminance increases and the contrast enhances on the wet road in the rain. That makes
visibility go up more than the increase of the light volume.
Power consumption is approximately 25 percent less than halogen headlamps, reducing battery load.
CAN Communication System DescriptionNKS002V7
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitNKS002V8
Refer to LAN-32, "CAN Communication Unit" .
Page 3581 of 4462
HEADLAMP - XENON TYPE - LT-19
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2006 December 2006 FX35/FX45
CONSULT-II Functions (BCM)NKS002VF
CONSULT-II can display each diagnostic item using the diagnostic test mode shown following.
CONSULT-II BASIC OPERATION
Refer to GI-38, "CONSULT-II Start Procedure" .
WORK SUPPORT
Operation Procedure
1. Touch “HEAD LAMP” on “SELECT TEST ITEM” screen.
2. Touch “WORK SUPPORT” on “SELECT DIAG MODE” screen.
3. Touch item on “SELECT WORK ITEM” screen.
4. Touch “START”.
5. Touch “CHANGE SET”.
6. The setting will be changed and “CUSTOMIZING COMPLETED” will be displayed.
7. Touch “END”.
Display Item List
DATA MONITOR
Operation Procedure
1. Touch “HEAD LAMP” on “SELECT TEST ITEM” screen.
2. Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
3. Touch either “ALL SIGNALS” or “SELECTION FROM MENU” on “SELECT MONITOR ITEM” screen.
4. When “SELECTION FROM MENU” is selected, touch individual items to be monitored. When “ALL SIG- NALS” is selected, all the items will be monitored.
5. Touch “START”.
6. Touch “RECORD” while monitoring, then the status of the monitored item can be recorded. To stop recording, touch “STOP”.
Display Item List
BCM diagnosis part Diagnosis mode Description
HEADLAMP WORK SUPPORT Changes the setting for each function.
DATA MONITOR Displays BCM input data in real time. ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
BCM SELF-DIAG RESULTS BCM performs self-diagnosis of CAN communication.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
Item Description CONSULT-II Factory setting
BATTERY SAVER SET Exterior lamp battery saver control mode can be changed in this mode.
Selects exterior lamp battery saver control mode between two ON/OFF. ON
×
OFF —
ALL SIGNALS Monitors all the signals.
SELECTION FROM MENU Selects items and monitors them.
Monitor item Contents
IGN ON SW “ON/OFF” Displays “IGN position (ON)/OFF, ACC position (OFF)” judged from ignition switch signal.
ACC ON SW “ON/OFF” Displays “ACC (ON)/OFF, Ignition OFF (OFF)” status judged from ignition switch signal.
HI BEAM SW “ON/OFF” Displays status (high beam switch: ON/Others: OFF) of high beam switch judged from
lighting switch signal.
HEAD LAMP SW 1 “ON/OFF” Displays status (headlamp switch 1: ON/Others: OFF) of headlamp switch 1 judged from
lighting switch signal.
HEAD LAMP SW 2 “ON/OFF” Displays status (headlamp switch 2: ON/Others: OFF) of headlamp switch 2 judged from
lighting switch signal.
Page 3641 of 4462
FRONT FOG LAMP LT-79
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2006 December 2006 FX35/FX45
to BCM terminal 38.
When ignition switch is in ACC or ON position, power is supplied
through 10A fuse [No. 6, located in fuse block (J/B)]
to BCM terminal 11.
Ground is supplied
to BCM terminals 49 and 52
through grounds M35, M45 and M85,
to IPDM E/R terminals 38 and 60
through grounds E21, E50 and E51.
FRONT FOG LAMP OPERATION
The front fog lamp switch is built into combination switch. The lighting switch must be in the 2ND position or
AUTO position (headlamp is ON) and the front fog lamp switch must be ON for front fog lamp operation.
With the front fog lamp switch in the ON position, the CPU located in the IPDM E/R grounds the coil side of the
front fog lamp relay. The front fog lamp relay then directs power
through IPDM E/R terminal 36
to front fog lamp RH terminal 1,
through IPDM E/R terminal 37
to front fog lamp LH terminal 1.
Ground is supplied
to front fog lamp RH and LH terminals 2
through grounds E21, E50 and E51.
With power and grounds supplied, front fog lamps illuminate.
COMBINATION SWITCH READING FUNCTION
Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" .
EXTERIOR LAMP BATTERY SAVER CONTROL
When the combination switch (lighting switch) is in the 2ND position (ON), the front fog lamp switch is ON, and
the ignition switch is turned from ON or ACC to OFF, the battery saver control feature is activated.
Under this condition, the front fog lamps (and headlamps) remain illuminated for 5 minutes, then the front fog
lamps (and headlamps) are turned off.
Exterior lamp battery saver control mode can be changed by the function setting of CONSULT-II.
CAN Communication System DescriptionNKS002WY
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitNKS002WZ
Refer to LAN-32, "CAN Communication Unit" .
Page 3697 of 4462
PARKING, LICENSE PLATE AND TAIL LAMPS LT-135
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2006 December 2006 FX35/FX45
to front side marker lamp LH terminal 2
through grounds E21, E50 and E51,
to parking lamp LH terminal 3
through grounds E21, E50 and E51,
to license plate lamp LH terminal 2
through grounds B15 and B45,
to rear combination lamp LH terminal 2
through grounds B15 and B45,
to front side marker lamp RH terminal 2
through grounds E21, E50 and E51,
to parking lamp RH terminal 3
through grounds E21, E50 and E51,
to license plate lamp RH terminal 2
through grounds B15 and B45,
to rear combination lamp RH terminal 2
through grounds B203 and B210,
to rear combination lamp control unit terminal 7
through grounds E21, E50 and E51.
With power and ground supplied, the parking, license plate, side marker and tail lamps illuminate.
COMBINATION SWITCH READING FUNCTION
Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" .
EXTERIOR LAMP BATTERY SAVER CONTROL
When the combination switch (lighting switch) is in the 1ST (or 2ND) position, and the ignition switch is turned
from ON or ACC to OFF, the battery saver control feature is activated.
Under this condition, the parking, license, side marker and tail lamps remain illuminated for 5 minutes, then the
parking, license plate, side marker and tail lamps are turned off.
Exterior lamp battery saver control mode can be changed by the function setting of CONSULT-II.
CAN Communication System DescriptionNKS003H1
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitNKS003H2
Refer to LAN-32, "CAN Communication Unit" .
Page 3752 of 4462
LT-190
ILLUMINATION
Revision: 2006 December 2006 FX35/FX45
to clock (illumination) terminal 3
to hazard switch (illumination) terminal 3
to heated seat switch (driver side) (illumination) terminal 5
to heated seat switch (passenger side) (illumination) terminal 5
to door mirror remote control switch (illumination) terminal 16
to LDW switch (illumination) terminal 5
to combination switch (spiral cable) terminal 26
to microphone terminal 2 (with telephone system)
to A/C and AV switch (illumination) terminal 3
to DVD player (illumination) terminal 12
to coin box illumination terminal 2
to rear power window switch LH and RH (illumination) terminals 6,
through combination switch (spiral cable) terminal 18
to audio steering switch (illumination), and
to icc steering switch (illumination) (with icc)
to ascd steering switch (illumination) (without icc)
Illumination control
through combination meter terminal 19
to A/T device (illumination) terminal 12
to snow mode switch (illumination) terminal 6
to VDC off switch (illumination) terminal 4
to clock (illumination) terminal 4
to hazard switch (illumination) terminal 4
to heated seat switch (driver side) (illumination) terminal 6
to heated seat switch (passenger side) (illumination) terminal 6
to door mirror remote control switch terminal 15
to LDW switch (illumination) terminal 4,
to combination switch (spiral cable) terminal 27
to A/C and AV switch (illumination) terminal 4
to DVD player (illumination) terminal 10,
through combination switch (spiral cable) terminal 21
to audio steering switch (illumination), and
to icc steering switch (illumination) (with icc)
to ascd steering switch (illumination) (without icc)
Ground is supplied at all times
to glove box lamp terminal 2, and
to coin box illumination terminal 3
through grounds M35, M45 and M85,
to rear power window switch LH and RH (illumination) terminals 7
through grounds B15 and B45.
With power and ground supplied, illumination lamps illuminate.
EXTERIOR LAMP BATTERY SAVER CONTROL
When the lighting switch is in the 1ST or 2ND position (or if auto light system is activated), and ignition switch
is turned from ON or ACC to OFF, battery saver control function is activated.
Under this condition, illumination lamps remain illuminated for 5 minutes, then illumination lamps are turned
off.
When the lighting switch is turned from OFF to 1ST or 2ND position (or if auto light system is activated) after
illumination lamps are turned off by battery saver control, and illumination lamps illuminate again.
Exterior lamp battery saver control mode can be changed by the function setting of CONSULT-II.
Page 3766 of 4462
LT-204
BULB SPECIFICATIONS
Revision: 2006 December 2006 FX35/FX45
BULB SPECIFICATIONSPFP:26297
HeadlampNKS002Z8
Exterior LampNKS002Z9
Interior Lamp/IlluminationNKS002ZA
Item Wattage (W)
High/Low (Xenon type) 35 (D2S)
Item Wattage (W)
Front combination lamp Front turn signal lamp 21 (amber)
Daytime/Parking lamp 21/5
Front side marker lamp 3.8
Rear combination lamp Stop/Tail lamp and Rear Turn signal lamp LED
Rear side marker lamp 3.8
Front fog lamp 35 (H8)
Back-up lamp 18
License plate lamp 5
High-mounted stop lamp (back door mount) LED
Item Wattage (W)
Map lamp 8
Interior room lamp 10
Personal lamp 8
Luggage room lamp 8
Step lamp 5
Glove box lamp 1.4
Vanity mirror lamp 1.32
Ignition key hole illumination 0.8
A/T device illumination lamp 1.4
Coin box illumination lamp 1.4
Page 4040 of 4462
RFD-2
PRECAUTIONS
Revision: 2006 December 2006 FX35/FX45
PRECAUTIONSPFP:00001
Service Notice or PrecautionsNDS000BH
Check for the correct installation status prior to removal or disassembly. If matching marks are required,
be certain they do not interfere with the function of the parts when applied.
Overhaul should be done in a clean work area, it is preferable to work in dustproof area.
Before disassembly, using steam or white gasoline, completely remove sand and mud from the exterior of
the unit, preventing them from entering into the unit during disassembly or assembly.
Check appearance of the disassembled parts for damage, deformation, and unusual wear. Replace them
with a new ones if necessary.
Gaskets, seals and O-rings should be replaced any time when the unit is disassembled.
In principle, tighten bolts or nuts gradually in several steps working diagonally from inside to outside. If
tightening sequence is specified, observe it.
Clean and flush the parts sufficiently and blow-dry them.
Be careful not to damage sliding surfaces and mating surfaces.
When applying sealant, remove the old sealant from the mounting surface; then remove any moisture, oil,
and foreign materials from the application and mounting surfaces.
Always use shop paper for cleaning the inside of components.
Avoid using cotton gloves or shop rags to prevent entering of lint.
During assembly, observe the specified tightening torque, and apply new gear oil, petroleum jelly, or multi-
purpose grease as specified for each vehicle, if necessary.