battery INFINITI FX35 2006 Service Manual

TROUBLE DIAGNOSES WORK FLOW LAN-5
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2006 December 2006 FX35/FX45
TROUBLE DIAGNOSES WORK FLOWPFP:00004
When Displaying CAN Communication System ErrorsNKS00349
WHEN A MALFUNCTION IS DETECTED BY CAN COMMUNICATION SYSTEM

CAN communication line is open. (CAN-H, CAN-L, or both)

CAN communication line is shorted. (Ground, between CAN lines, or other harnesses)

The areas related to CAN communication of unit is malfunctioning.
WHEN A MALFUNCTION IS DETECTED EXCEPT CAN COMMUNICATION SYSTEM

Removal and installation of parts: When the units that perform CAN communication or the sensors related
to CAN communication are removed and installed, malfunction may be detected (or DTC other than CAN
communication may be detected).

Fuse blown out (removed): CAN communication of the unit may be stopped at such time.

Low voltage: If the voltage decreases because of battery discharge when IGN is ON, malfunction may be
detected by self-diagnosis according to the units.

LAN-34
[CAN]
CAN COMMUNICATION
Revision: 2006 December 2006 FX35/FX45
ASCD operation signal T R
ASCD SET lamp signal T R
Battery voltage signal T R
Closed throttle position signal T R
Cooling fan speed request sig-
nal T
R
Engine coolant temperature
signal TR
Engine speed signal T R R R R
Engine status signal T R
Fuel consumption monitor sig-
nal TR
RT
Malfunctioning indicator lamp
signal TR
Wide open throttle position sig-
nal TR
A/T CHECK indicator lamp sig-
nal TR
A/T self-diagnosis signal R T
Current gear position signal T R
Manual mode indicator signal T R
Output shaft revolution signal R T
P range signal T R R
Shift position indicator signal T R
Turbine revolution signal R T
A/C switch/indicator signal TR
RT
System setting signal TR R
RT T
Alarm request signal T R
Back door open request signal T R
Door lock/unlock request signal T R
Ignition knob switch signal T R
Key warning signal T R
Power window open request
signal TR
Sleep wake up signal TR R
TR
Buzzer output signal TR
TR
A/C switch signal R T Signals ECM TCM
Dis-
play
control unit Intelli-
gent
Key unit BCM Steer-
ing
angle
sensor Unified
meter
and A/
C amp. ABS
actua-
tor and
electric
unit
(con- trol
unit) Driver
seat
control unit IPDM
E/R

CAN COMMUNICATION LAN-37
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2006 December 2006 FX35/FX45
ASCD operation signal T R
Battery voltage signal T R
Closed throttle position
signal TR R
Cooling fan speed
request signal T
R
Engine coolant tempera-
ture signal TR
Engine speed signal T R R R R R
Engine status signal T R
Fuel consumption moni-
tor signal TR
RT
ICC steering switch sig-
nal TR
Malfunctioning indicator
lamp signal TR
Wide open throttle posi-
tion signal TR
Snow mode switch signal RT
TR
A/T CHECK indicator
lamp signal TR
A/T self-diagnosis signal R T
Current gear position sig-
nal TR R
Manual mode indicator
signal TR R
Output shaft revolution
signal RT R R
P range signal T R R R
Shift position indicator
signal TR R
Turbine revolution signal R T R
A/C switch/indicator sig-
nal TR
RT
System setting signal TR R
RT T
ICC OD cancel request
signal RT
ICC operation signal R T
ICC system display sig-
nal TR
Signals ECM TCM
Dis-
play
con-
trol
unit ICC
unit Intelli-
gent Key unit BCM Ste er-
ing
angle
sen- sor LDW
cam- era
unit Uni-
fied
meter and
A/C
amp. ICC
sen-
sor ABS
actu- ator and
elec- tric
unit
(con- trol
unit) Driver
seat
con-
trol
unit IPDM
E/R

CAN COMMUNICATION LAN-41
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2006 December 2006 FX35/FX45
Input/Output Signal Chart
T: Transmit R: Receive
Signals ECM TCM Dis-
play
control unit AW D
control unit Intelli-
gent
Key unit BCM Stee r-
ing
angle
sensor Unified
meter
and A/
C amp. ABS
actua-
tor and elec-
tric unit (con-trol
unit) Driver
seat
control unit IPDM
E/R
A/C compressor feedback
signal TR
A/C compressor request
signal T
R
Accelerator pedal position
signal TR R R
ASCD CRUISE lamp sig-
nal TR
ASCD OD cancel request
signal TR
ASCD operation signal T R
ASCD SET lamp signal T R
Battery voltage signal T R
Closed throttle position
signal TR
Cooling fan speed request
signal T
R
Engine coolant tempera-
ture signal TR
Engine speed signal T R R R R R
Engine status signal T R
Fuel consumption monitor
signal TR
RT
Malfunction indicator lamp
signal TR
Wide open throttle posi-
tion signal TR
Snow mode switch signal R T
A/T CHECK indicator
lamp signal TR
A/T self-diagnosis signal R T
Current gear position sig-
nal TR
Manual mode indicator
signal TR
Output shaft revolution
signal RT
P range signal T R R
Shift position indicator sig-
nal TR
Turbine revolution signal R T
A/C switch/indicator signal TR
RT

LAN-44
[CAN]
CAN COMMUNICATION
Revision: 2006 December 2006 FX35/FX45
TYPE 6
System Diagram

Ty p e 6
Input/Output Signal Chart
T: Transmit R: Receive
PKIB4174E
Signals ECM TCM Dis-
play
con- trol
unit AW D
con-
trol
unit ICC
unit Intel-
ligent
Key unit BCM Steer-
ing
angle sen-
sor LDW
cam-
era
unit Uni-
fied
meter
and
A/C
amp. ICC
sen- sor ABS
actu-
ator and
elec-
tric
unit
(con-
trol
unit) Driver
seat
con- trol
unit IPDM
E/R
A/C compressor
feedback signal TR
A/C compressor
request signal T
R
Accelerator pedal
position signal TR R R R
ASCD OD cancel
request signal TR
ASCD operation sig-
nal TR
Battery voltage sig-
nal TR
Closed throttle posi-
tion signal TR R
Cooling fan speed
request signal T
R
Engine coolant tem-
perature signal TR
Engine speed signal T R R R R R R
Engine status signal T R
Fuel consumption
monitor signal TR
RT

LAN-190
[CAN]
TROUBLE DIAGNOSIS FOR SYSTEM
Revision: 2006 December 2006 FX35/FX45
TROUBLE DIAGNOSIS FOR SYSTEMPFP:00000
Inspection Between TCM and Data Link Connector CircuitNKS0038T
1. CHECK HARNESS FOR OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Disconnect ECM connector and harness connector M82.
4. Check continuity between harness connector and data link con- nector.
OK or NG
OK >> Connect all the connectors and diagnose again. Refer to LAN-5, "
TROUBLE DIAGNOSES WORK FLOW" .
NG >> Repair harness.
Inspection Between Data Link Connector and Unified Meter and A/C Amp. Cir-
cuit
NKS0038U
1. CHECK HARNESS FOR OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Disconnect ECM connector and unified meter and A/C amp. connector.
4. Check continuity between data link connector and unified meter and A/C amp. harness connector.
OK or NG
OK >> Connect all the connectors and diagnose again. Refer to LAN-5, "
TROUBLE DIAGNOSES WORK FLOW" .
NG >> Repair harness.
Inspection Between Unified Meter and A/C Amp. and ABS Actuator and Electric
Unit (Control Unit) Circuit
NKS0038V
1. CHECK CONNECTOR
1. Turn ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check following terminals and connectors for damage, bend and loose connection (connector side and harness side).
–Harness connector M41
–Harness connector E211
OK or NG
OK >> GO TO 2.
NG >> Repair terminal or connector.
Harness con- nector Terminal Data link con-
nector Terminal Continuity
M82 14H
M5 6Yes
15H 14 Yes
SKIA6861E
Data link con- nector Terminal Unified meter
and A/C amp. connector Terminal Continuity
M5 6
M55 1Yes
14 11 Yes
SKIA6862E

TROUBLE DIAGNOSIS FOR SYSTEM LAN-191
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2006 December 2006 FX35/FX45
2. CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect unified meter and A/C amp. connector and harness connector M41.
2. Check continuity between unified meter and A/C amp. harness connector (A) and harness connector (B).
OK or NG
OK >> GO TO 3.
NG >> Repair harness.
3. CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect ABS actuator and electric unit (control unit) connector.
2. Check continuity between harness connector (A) and ABS actu- ator and electric unit (control unit) harness connector (B).
OK or NG
OK >> Connect all the connectors and diagnose again. Refer to LAN-5, "
TROUBLE DIAGNOSES WORK FLOW" .
NG >> Repair harness.
Inspection Between ABS Actuator and Electric Unit (Control Unit) and Driver
Seat Control Unit Circuit
NKS0038W
1. CHECK CONNECTOR
1. Turn ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check following terminals and connectors for damage, bend and loose connection (connector side and harness side).
–Harness connector E205
–Harness connector B5
OK or NG
OK >> GO TO 2.
NG >> Repair terminal or connector.
AB Continuity
Connector Terminal Connector Terminal
M55 1
M41 29G Yes
11 18G Yes
PKIC9644E
AB Continuity
Connector Terminal Connector Terminal
E211 29G
E56 11 Ye s
18G 15 Yes
PKIC9645E

LAN-192
[CAN]
TROUBLE DIAGNOSIS FOR SYSTEM
Revision: 2006 December 2006 FX35/FX45
2. CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect ABS actuator and electric unit (control unit) connector and harness connector E205.
2. Check continuity between ABS actuator and electric unit (control unit) harness connector (A) and harness connector (B).
OK or NG
OK >> GO TO 3.
NG >> Repair harness.
3. CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect harness connector B8.
2. Check continuity between harness connector (A) and harness connector (B).
OK or NG
OK >> Connect all the connectors and diagnose again. Refer to LAN-5, "
TROUBLE DIAGNOSES WORK FLOW" .
NG >> Repair harness.
ECM Circuit InspectionNKS0038X
1. CHECK CONNECTOR
1. Turn ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check terminals and connector of ECM for damage, bend and loose connection (control module side and harness side).
OK or NG
OK >> GO TO 2.
NG >> Repair terminal or connector.
2. CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect ECM connector.
2. Check resistance between ECM harness connector terminals.
OK or NG
OK >> Replace ECM.
NG >> Repair harness between ECM and harness connector M82.
AB Continuity
Connector Terminal Connector Terminal
E56 11
E205 4Yes
15 10 Yes
PKIC9646E
AB Continuity
Connector Terminal Connector Terminal
B5 4
B8 10 Yes
10 9 Yes
PKIC9647E
ECM connector Terminals Resistance
(Approx.)
M90 94 86 108 – 132 Ω
PKIA9860E

TROUBLE DIAGNOSIS FOR SYSTEM LAN-193
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2006 December 2006 FX35/FX45
TCM Circuit InspectionNKS0038Y
1. CHECK CONNECTOR
1. Turn ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check following terminals and connectors for damage, bend and loose connection (control module side and harness side).
–A/T assembly connector
–Harness connector F102
–Harness connector M82
OK or NG
OK >> GO TO 2.
NG >> Repair terminal or connector.
2. CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect A/T assembly connector.
2. Check resistance between A/T assembly harness connector ter- minals.
OK or NG
OK >> Replace control valve with TCM.
NG >> Repair harness between A/T assembly and display con- trol unit.
Display Control Unit Circuit InspectionNKS0038Z
1. CHECK CONNECTOR
1. Turn ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check terminals and connector of display control unit for damage, bend and loose connection (control unit side and harness side).
OK or NG
OK >> GO TO 2.
NG >> Repair terminal or connector.
2. CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect display control unit connector.
2. Check resistance between display control unit harness connec- tor terminals.
OK or NG
OK >> Replace display control unit.
NG >> Repair harness between display control unit and har- ness connector M82.
A/T assembly con-
nector Terminals Resistance
(Approx.)
F44 3 8 54 – 66 Ω
SKIA6866E
Display control
unit connector Terminals
Resistance
(Approx.)
M76 25 26 54 – 66 Ω
SKIA6884E

LAN-194
[CAN]
TROUBLE DIAGNOSIS FOR SYSTEM
Revision: 2006 December 2006 FX35/FX45
AWD Control Unit Circuit InspectionNKS00390
1. CHECK CONNECTOR
1. Turn ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check terminals and connector of AWD control unit for damage, bend and loose connection (control unit side and harness side).
OK or NG
OK >> GO TO 2.
NG >> Repair terminal or connector.
2. CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect AWD control unit connector.
2. Check resistance between AWD control unit harness connector terminals.
OK or NG
OK >> Replace AWD control unit.
NG >> Repair harness between AWD control unit and harness connector M82.
ICC Unit Circuit InspectionNKS00391
1. CHECK CONNECTOR
1. Turn ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check terminals and connector of ICC unit for damage, bend and loose connection (unit side and harness side).
OK or NG
OK >> GO TO 2.
NG >> Repair terminal or connector.
2. CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect ICC unit connector.
2. Check resistance between ICC unit harness connector termi- nals.
OK or NG
OK >> Replace ICC unit.
NG >> Repair harness between ICC unit and harness connec- tor M82.
AWD control unit
connector Terminals Resistance
(Approx.)
M92 8 16 54 – 66 Ω
SKIA6889E
ICC control unit Terminals Resistance
(Approx.)
M88 14 5 54 – 66 Ω
SKIA6886E