Cmp INFINITI FX35 2007 Service Manual

ACS-2Revision: 2006 July 2007 FX35/FX45
DTC 65 PRESSURE CONTROL .........................
... 54
DTC 74 LASER BEAM OFF CNTR ..................... ... 55
DTC 90 STOP LAMP RLY FIX ............................ ... 55
DTC 92 ECM CIRCUIT ........................................ ... 61
DTC 96 NP RANGE ............................................ ... 62
DTC 97 AT CIRCUIT ........................................... ... 64
DTC 98 GEAR POSITION ................................... ... 64
DTC 102 RADAR STAIN ..................................... ... 65
DTC 103 LASER SENSOR FAIL ......................... ... 65
DTC 104 LASER AIMING INCMP ....................... ... 66
DTC 107 LASER COMM FAIL ............................. ... 66
DTC 109 LASER HIGH TEMP ............................ ... 66
TROUBLE DIAGNOSIS FOR SYMPTOMS ........... ... 67
Symptom Chart .................................................... ... 67
Symptom 1: MAIN Switch Does Not Turn ON*
1 ,
MAIN Switch Does Not Turn OFF*
2 ..................... ... 68
Symptom 2: ICC System Cannot Be Set (MAIN
Switch Turns ON/OFF) ........................................ ... 68
Symptom 3: ICC System Cannot Be Operated by
CANCEL Switch, RESUME/ACCELERATE Switch
or DISTANCE Switch ........................................... ... 69
Symptom 4: ICC System Is Not Cancelled When the A/T Selector Lever Is in Other Than “D” and “M”
Position ................................................................ ... 70
Symptom 5: Chime Does Not Sound ................... ... 70
Symptom 6: Driving Force Is Hunting .................. ... 71
Symptom 7: ICC System Frequently Cannot Detect
the Vehicle Ahead/ Detection Zone Is Short ........ ... 71
Symptom 8: The System Does Not Detect the Vehi-
cle Ahead at All .................................................... ... 72
ELECTRICAL COMPONENT INSPECTION .......... ... 73
ICC Steering Switch ............................................. ... 73
Booster Solenoid .................................................. ... 73
Release Switch .................................................... ... 73
ICC Brake Switch and Stop Lamp Switch ............ ... 74
ICC Brake Hold Relay .......................................... ... 74
REMOVAL AND INSTALLATION ........................... ... 75
ICC Unit ............................................................... ... 75
REMOVAL ......................................................... ... 75
INSTALLATION ................................................. ... 75
ICC Sensor .......................................................... ... 75
REMOVAL ......................................................... ... 75
INSTALLATION ................................................. ... 76
ICC Steering Switch ............................................. ... 76

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS ACS-43
[ICC]
C
D E
F
G H
I
J
L
M A
B
ACS
Revision: 2006 July 2007 FX35/FX45
90 STOP LAMP RLY FIX×× ×
Normally open terminal of stop
lamp relay is stuck. ACS-55
92 ECM CIRCUIT
××××

ECM malfunction

Accelerator pedal position sensor
malfunction

ICC unit malfunction ACS-61
96 NP RANGE
×××

Park/neutral position switch har-
ness is open or shorted.

Park/neutral position switch mal-
function.

TCM malfunction ACS-62
97 AT CIRCUIT
×××
TCM malfunctionACS-64
98 GEAR POSITION ×××

TCM malfunction

AT turbine revolution sensor mal-
function

AT vehicle speed sensor malfunc-
tion ACS-64
102 RADAR STAIN
×× ×
ICC sensor body window has con-
tamination. ACS-65
103 LASER SENSOR FAIL
×× ×
ICC sensor internal malfunctionACS-65
104 LASER AIMING INCMP ×× ×
Laser beam aiming of ICC sensor
is not adjusted. ACS-66
107 LASER COMM FAIL
×× ×

CAN data received by ICC sensor
is strange (from ICC unit, combi-
nation meter or ECM). ACS-66
109 LASER HIGH TEMP
×× ×
Temperature around ICC sensor is
excessively high. ACS-66
DTC
No. CONSULT-II
screen terms ICC
system
warning
lamp Fail-safe
Malfunctions detected where... Refer-
ence
page
Vehicle-
to-
vehicle
distance control
mode Conven-
tional
(fixed
speed)
cruise
control mode Brake
assist (with
preview
function)

ACS-66
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: 2006 July 2007 FX35/FX45
DTC 104 LASER AIMING INCMPNKS003FN
1. CHECK DIAGNOSIS
1. Adjust laser beam aiming. Erase DTC and perform ICC system running test.
2. After that, perform self-diagnosis of ICC system.
3. Check if “DTC 104 LASER AIMING INCMP” is indicated.
Is it indicated?
YES >> 1. Replace ICC sensor, and adjust laser beam aiming. 2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system again.
NO >> INSPECTION END
DTC 107 LASER COMM FAILNKS003FO
1. CHECK ICC UNIT SELF-DIAGNOSIS
1. Perform self-diagnosis.
2. Check if “DTC 11 CONTROL UNIT” or “DTC 20 CAN COMM CIRCUIT” item other than “DTC 107 LASER COMM FAIL” is indicated in the self-diagnosis item in the display.
Is any indicated?
YES >> Go to applicable item inspection. Refer to ACS-44, "DTC 11 CONTROL UNIT" , and ACS-44,
"DTC 20 CAN COMM CIRCUIT" .
NO >> 1. Replace ICC sensor, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system again.
DTC 109 LASER HIGH TEMPNKS003FP
1. CHECK SYMPTOM
Check if cooling system malfunctions.
Does it malfunction?
YES >> 1. Repair cooling system. 2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system again.
NO >> 1. Replace ICC sensor, and adjust laser beam aiming. 2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system again.

DTC P0700 TCM AT-111
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2006 July 2007 FX35/FX45
DTC P0700 TCMPFP:31036
DescriptionNCS001C6
The TCM consists of a microcomputer and connectors for signal input and output and for power supply. The
TCM controls the A/T.
On Board Diagnosis LogicNCS001C7

This is an OBD-II self-diagnostic item.

Diagnostic trouble code “P0700 TCM” with CONSULT-II is detected when TCM is malfunctioning.
Possible CauseNCS001C8
TCM.
DTC Confirmation ProcedureNCS001C9
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch OFF and
wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch ON.
2. Select “ECU INPUT SIGNALS” or “MAIN SIGNALS” in “DATA MONITOR” mode for “A/T” with CONSULT-II.
3. Touch “START”.
4. Start engine.
5. Run engine for at least 2 consecutive seconds at idle speed.
6. If DTC is detected, go to AT- 111 , "
Diagnostic Procedure" .
WITH GST
Follow the procedure “WITH CONSULT-II”.
Diagnostic ProcedureNCS001CA
1. CHECK DTC
With CONSULT-II
1. Turn ignition switch ON.
2. Select “SELF DIAG RESULTS” mode for “A/T” with CONSULT-II.
3. Touch “ERASE”.
4. Turn ignition switch OFF and wait at least 10 seconds.
5. Perform AT- 111 , "
DTC Confirmation Procedure" .
Is the
“P0700 TCM” displayed again?
YES >> Replace the control valve with TCM. Refer to AT- 2 3 9 , "Control Valve with TCM and A/T Fluid Tem-
perature Sensor 2" .
NO >> INSPECTION END
BCIA0031E

DI-2Revision: 2006 July 2007 FX35/FX45
Oil Pressure Warning Lamp Does Not Turn Off (Oil
Pressure Is Normal) ............................................. ... 49
Component Inspection ......................................... ... 51
OIL PRESSURE SWITCH ................................ ... 51
A/T INDICATOR ..................................................... ... 52
System Description .............................................. ... 52
MANUAL MODE ............................................... ... 52
NOT MANUAL MODE ...................................... ... 52
Wiring Diagram — AT/IND — .............................. ... 53
A/T Indicator Is Malfunction ................................. ... 55
WARNING CHIME .................................................. ... 56
System Description .............................................. ... 56
POWER SUPPLY AND CIRCUIT ..................... ... 56
IGNITION KEY WARNING CHIME (WITHOUT
INTELLIGENT KEY) ......................................... ... 57
IGNITION KEY WARNING CHIME (WITH INTEL-
LIGENT KEY) ................................................... ... 57
LIGHT WARNING CHIME ................................ ... 58
SEAT BELT WARNING CHIME ........................ ... 58
Component Parts and Harness Connector Location ... 59
Schematic ............................................................ ... 60
Wiring Diagram — CHIME — .............................. ... 61
Terminals and Reference Value for BCM ............. ... 64
Terminals and Reference Value for Unified Meter
and A/C Amp. ...................................................... ... 65
Terminals and Reference Value for Combination
Meter ................................................................... ... 66
CONSULT-II Function (METER A/C AMP) .......... ... 66
CONSULT-II Function (BCM) ............................... ... 66
DIAGNOSIS ITEMS DESCRIPTION ................ ... 66
CONSULT-II BASIC OPERATION .................... ... 66
DATA MONITOR ............................................... ... 66
ACTIVE TEST .................................................. ... 67
SELF-DIAG RESULTS ..................................... ... 67
Trouble Diagnosis ................................................ ... 67
HOW TO PERFORM TROUBLE DIAGNOSIS . ... 67
PRELIMINARY INSPECTION .......................... ... 68
Symptom Chart .................................................... ... 68
Power Supply and Ground Circuit Inspection ...... ... 68
Combination Meter Buzzer Circuit Inspection ...... ... 69
Front Door Switch (Driver Side) Signal Inspection ... 71
Key Switch Signal Inspection (Without Intelligent
Key) ..................................................................... ... 72
Key Switch and Ignition Knob Switch Signal Inspec-
tion (With Intelligent Key, When Mechanical Key Is
Used) ................................................................... ... 73
Lighting Switch Signal Inspection ........................ ... 74
Seat Belt Buckle Switch (Driver Side) Signal Inspec-
tion ....................................................................... ... 75
Component Inspection ......................................... ... 76
FRONT DOOR SWITCH (DRIVER SIDE) ........ ... 76
KEY SWITCH ................................................... ... 76
KEY SWITCH AND IGNITION KNOB SWITCH ... 76
SEAT BELT BUCKLE SWITCH (DRIVER SIDE) ... 76
LANE DEPARTURE WARNING SYSTEM ............. ... 77
Precautions for Lane Departure Warning (LDW)
system ................................................................. ... 77
System Description .............................................. ... 77 LDW SYSTEM OPERATION ............................
... 77
POWER SUPPLY AND GROUND CIRCUIT .... ... 79
Action Test ........................................................... ... 80
LDW SYSTEM RUNNING TEST ...................... ... 80
Camera Aiming Adjustment ................................. ... 80
OUTLINE .......................................................... ... 80
PREPARATION ................................................. ... 80
TARGET SETTING ........................................... ... 80
VEHICLE HEIGHT CHECK .............................. ... 83
AIMING ADJUSTMENT .................................... ... 83
Component Parts and Harness Connector Location ... 87
Schematic ............................................................ ... 88
Wiring Diagram — LDW — .................................. ... 89
Terminals and Reference Value for LDW Camera
Unit ....................................................................... ... 92
CONSULT-II Function (LDW) ............................... ... 92
DESCRIPTION ................................................. ... 92
CONSULT-II BASIC OPERATION .................... ... 92
WORK SUPPORT ............................................ ... 92
SELF-DIAG RESULTS ...................................... ... 92
DATA MONITOR ............................................... ... 93
ACTIVE TEST ................................................... ... 94
Trouble Diagnosis ................................................ ... 95
HOW TO PERFORM TROUBLE DIAGNOSIS . ... 95
SYMPTOM CHART ........................................... ... 95
Preliminary Inspection .......................................... ... 95
Power Supply and Ground Circuit Inspection ...... ... 96
DTC [C1B00] CAMERA UNIT MALF ................... ... 97
DTC [C1B01] CAM AIMING INCMP .................... ... 97
DTC [C1B02] VHCL SPD DATA MALF ................ ... 97
DTC [C1B03] ABNRML TEMP DETECT ............. ... 98
DTC [U1000] CAN COMM CIRCUIT ................... ... 98
DTC [U1010] CONTROL UNIT (CAN) ................. ... 98
LDW Chime Circuit Inspection ............................. ... 98
LDW Switch Circuit Inspection ............................. ... 99
LDW Indicator Lamp Circuit Inspection ................ .102
Turn Signal Input Inspection ................................ .103
Electrical Component Inspection ......................... .103
LDW SWITCH ................................................... .103
Removal and Installation for LDW Camera Unit .. .104
REMOVAL ......................................................... .104
INSTALLATION ................................................. .104
Removal and Installation for LDW Chime ............ .104
REMOVAL ......................................................... .104
INSTALLATION ................................................. .104
Removal and Installation for LDW Switch ............ .104
CAN COMMUNICATION ........................................ .105
System Description .............................................. .105
CAN Communication Unit .................................... .105
COMPASS .............................................................. .106
Precautions for Compass ..................................... .106
System Description .............................................. .106
Troubleshooting ................................................... .107
Zone Variation Setting Procedure ........................ .108
Calibration Procedure .......................................... .108
Wiring Diagram — COMPAS — ........................... .109
Removal and Installation of Compass .................. .110
CLOCK ................................................................... . 111

LANE DEPARTURE WARNING SYSTEM DI-93
C
D E
F
G H
I
J
L
M A
B
DI
Revision: 2006 July 2007 FX35/FX45
Display Item
NOTE:

When a DTC is detected, the LDW system dose not operate.

When the DTC except “ABNRML TEMP DETECT [C1B03] ” is detected, the LDW indicator lamp turns ON.

When the DTC “ABNRML TEMP DETECT [C1B03] ” is detected, the LDW system ON indicator lamp blinks.
DATA MONITOR
Operation Procedure
1. Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
2. Touch any of “ALL SIGNALS” and “SELECTION FROM MENU” on selection screen.
3. Touch “START”.
4. Display the data monitor.
5. If necessary, touch “COPY” in turn, and print data.
Monitored Item
Display item [Code] Malfunctions detected where... Reference
page
CAMERA UNIT MALF [C1B00] LDW camera unit internal malfunction DI-97
CAM AIMING INCMP [C1B01] LDW camera aiming is not adjusted.DI-97
VHCL SPD DATA MALF [C1B02] LDW camera unit detected different vehicle speed signal from TCM and ABS
actuator and electric unit (control unit). DI-97
ABNRML TEMP DETECT [C1B03] Temperature around LDW camera unit is excessively high.
DI-98
CAN COMM CIRCUIT [U1000] LDW camera unit detected CAN communication malfunction.DI-98
CONTROL UNIT (CAN) [U1010] LDW camera unit detected internal CAN communication circuit malfunction.DI-98
Monitored Item [unit] Description
MAIN SW [ON/OFF] Displays [ON/OFF] status as judged from LDW switch signal.
SW ON LAMP [ON/OFF] Displays [ON/OFF] status of LDW system ON indicator signal output.
INDICATE LAMP [ON/OFF] Displays [ON/OFF] status of LDW indicator signal output.
BUZZER OUTPUT [ON/OFF] Displays [ON/OFF] status of LDW chime operation signal output.
LDW INACCURAT [ON/OFF] Displays LDW camera unit status.
VHCL SPD SE [km/h] or [mph] Displays vehicle speed calculated by LDW camera unit through CAN communication [ABS
actuator and electric unit (control unit) transmits wheel sensor signal through CAN commu-
nication].
VHCL SPD AT [km/h] or [mph] Displays vehicle speed calculated from A/T vehicle speed sensor by LDW camera unit
through CAN communication (TCM transmits A/T vehicle speed sensor signal through CAN
communication).
TURN SIGNAL [OFF/LH/RH] Displays “Turn signal” status, determined from BCM through CAN communication.
LANE DETCT LH [ON/OFF] Displays left lane marker is detected.
LANE DETCT RH [ON/OFF] Displays right lane marker is detected.
CROSS LANE LH [ON/OFF] Displays vehicle is crossing left lane.
CROSS LANE RH [ON/OFF] Displays vehicle is crossing right lane.
WARN LANE LH [ON/OFF] Displays warning for left lane.
WARN LANE RH [ON/OFF] Displays warning for right lane.
VALID POS LH [VLD/INVLD] Displays lateral position for left lane marker is valid.
VALID POS RH [VLD/INVLD] Displays lateral position for right lane marker is valid.
AIMING DONE [OK/NG] Displays camera aiming done.
AIMING RESULT [OK/NOK] Displays camera aiming result.
FCTRY AIM YAW [deg] Displays camera unit installation condition.
FCTRY AIM ROL [deg] Displays camera unit installation condition.

LANE DEPARTURE WARNING SYSTEM DI-97
C
D E
F
G H
I
J
L
M A
B
DI
Revision: 2006 July 2007 FX35/FX45
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect LDW camera unit connector.
3. Check continuity between LDW camera unit harness connector R9 terminals 6, 12 and ground.
OK or NG
OK >> INSPECTION END
NG >> Repair ground harness.
DTC [C1B00] CAMERA UNIT MALFNKS0031E
1. CHECK LDW CAMERA UNIT
1. Perform self-diagnosis of LDW camera unit.
2. Check if any item other than “[C1B00] CAMERA UNIT” is displayed on self-diagnosis display.
Is any displayed?
YES >> Repair or replace applicable item.
NO >> Replace LDW camera unit.
DTC [C1B01] CAM AIMING INCMPNKS0031F
1. PREFORM CAMERA AIMING ADJUSTMENT
1. Preform camera aiming adjustment. Refer to DI-80, "
Camera Aiming Adjustment" .
2. Erase DTC and perform the LDW camera unit self-diagnosis.
Self
-diagnosis results
No malfunction detected >> INSPECTION END
Malfunction detected >> Replace LDW camera unit.
DTC [C1B02] VHCL SPD DATA MALFNKS0031G
1. CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) (CONSULT-II)
Perform self-diagnosis of ABS actuator and electric unit (control unit). Refer to BRC-24, "
CONSULT-II Func-
tions (ABS)" .
Self
-diagnosis results
No malfunction detected >> GO TO 2.
Malfunction detected >> Check applicable parts, and repair or replace corresponding parts.
2. CHECK TCM (CONSULT-II)
Perform self-diagnosis of TCM. Refer to AT- 9 0 , "
CONSULT-II Function (A/T)" .
Self
-diagnosis results
No malfunction detected >> Replace LDW camera unit.
Malfunction detected >> Check applicable parts, and repair or replace corresponding parts. 6 – Ground
: Continuity should exist.
12 – Ground
PKIC0247E

EC-4Revision: 2006 July 2007 FX35/FX45
Component Inspection .........................................
.344
Removal and Installation ..................................... .344
DTC P0300 - P0306 MULTIPLE CYLINDER MIS-
FIRE, NO. 1 - 6 CYLINDER MISFIRE .................... .345
On Board Diagnosis Logic ................................... .345
DTC Confirmation Procedure .............................. .346
Diagnostic Procedure .......................................... .346
DTC P0327, P0328 KS ........................................... .355
Component Description ....................................... .355
On Board Diagnosis Logic ................................... .355
DTC Confirmation Procedure .............................. .355
Wiring Diagram .................................................... .356
Diagnostic Procedure .......................................... .357
Component Inspection ......................................... .358
Removal and Installation ..................................... .359
DTC P0335 CKP SENSOR (POS) ......................... .360
Component Description ....................................... .360
CONSULT-II Reference Value in Data Monitor Mode .360
On Board Diagnosis Logic ................................... .360
DTC Confirmation Procedure .............................. .361
Wiring Diagram .................................................... .362
Diagnostic Procedure .......................................... .363
Component Inspection ......................................... .366
Removal and Installation ..................................... .366
DTC P0340, P0345 CMP SENSOR (PHASE) ........ .367
Component Description ....................................... .367
CONSULT-II Reference Value in Data Monitor Mode .367
On Board Diagnosis Logic ................................... .367
DTC Confirmation Procedure .............................. .368
Wiring Diagram .................................................... .369
Diagnostic Procedure .......................................... .372
Component Inspection ......................................... .375
Removal and Installation ..................................... .375
DTC P0420, P0430 THREE WAY CATALYST FUNC-
TION ....................................................................... .376
On Board Diagnosis Logic ................................... .376
DTC Confirmation Procedure .............................. .376
Overall Function Check ....................................... .377
Diagnostic Procedure .......................................... .378
DTC P0441 EVAP CONTROL SYSTEM ................ .382
System Description .............................................. .382
On Board Diagnosis Logic ................................... .382
DTC Confirmation Procedure .............................. .382
Overall Function Check ....................................... .383
Diagnostic Procedure .......................................... .384
DTC P0442 EVAP CONTROL SYSTEM ................ .387
On Board Diagnosis Logic ................................... .387
DTC Confirmation Procedure .............................. .388
Diagnostic Procedure .......................................... .389
DTC P0443 EVAP CANISTER PURGE VOLUME
CONTROL SOLENOID VALVE .............................. .396
Description ........................................................... .396
CONSULT-II Reference Value in Data Monitor Mode .396
On Board Diagnosis Logic ................................... .397
DTC Confirmation Procedure .............................. .397
Wiring Diagram .................................................... .398 Diagnostic Procedure ...........................................
.400
Component Inspection ......................................... .403
Removal and Installation ...................................... .403
DTC P0444, P0445 EVAP CANISTER PURGE VOL-
UME CONTROL SOLENOID VALVE ..................... .404
Description ........................................................... .404
CONSULT-II Reference Value in Data Monitor Mode .404
On Board Diagnosis Logic ................................... .405
DTC Confirmation Procedure ............................... .405
Wiring Diagram .................................................... .406
Diagnostic Procedure ........................................... .408
Component Inspection ......................................... .409
Removal and Installation ...................................... .410
DTC P0447 EVAP CANISTER VENT CONTROL
VALVE ..................................................................... .411
Component Description ....................................... .411
CONSULT-II Reference Value in Data Monitor Mode .411
On Board Diagnosis Logic ................................... .411
DTC Confirmation Procedure ............................... .412
Wiring Diagram .................................................... .413
Diagnostic Procedure ........................................... .414
Component Inspection ......................................... .416
DTC P0448 EVAP CANISTER VENT CONTROL
VALVE ..................................................................... .418
Component Description ....................................... .418
CONSULT-II Reference Value in Data Monitor Mode .418
On Board Diagnosis Logic ................................... .418
DTC Confirmation Procedure ............................... .419
Wiring Diagram .................................................... .420
Diagnostic Procedure ........................................... .421
Component Inspection ......................................... .422
DTC P0451 EVAP CONTROL SYSTEM PRESSURE
SENSOR ................................................................. .424
Component Description ....................................... .424
CONSULT-II Reference Value in Data Monitor Mode .424
On Board Diagnosis Logic ................................... .424
DTC Confirmation Procedure ............................... .425
Diagnostic Procedure ........................................... .425
Component Inspection ......................................... .426
DTC P0452 EVAP CONTROL SYSTEM PRESSURE
SENSOR ................................................................. .427
Component Description ....................................... .427
CONSULT-II Reference Value in Data Monitor Mode .427
On Board Diagnosis Logic ................................... .427
DTC Confirmation Procedure ............................... .428
Wiring Diagram .................................................... .429
Diagnostic Procedure ........................................... .430
Component Inspection ......................................... .432
DTC P0453 EVAP CONTROL SYSTEM PRESSURE
SENSOR ................................................................. .433
Component Description ....................................... .433
CONSULT-II Reference Value in Data Monitor Mode .433
On Board Diagnosis Logic ................................... .433

EC-10Revision: 2006 July 2007 FX35/FX45
Diagnostic Procedure ..........................................
.935
Removal and Installation ..................................... .940
DTC P0137, P0157 HO2S2 .................................... .941
Component Description ....................................... .941
CONSULT-II Reference Value in Data Monitor Mode .941
On Board Diagnosis Logic ................................... .941
DTC Confirmation Procedure .............................. .942
Overall Function Check ....................................... .943
Wiring Diagram .................................................... .944
Diagnostic Procedure .......................................... .947
Component Inspection ......................................... .950
Removal and Installation ..................................... .951
DTC P0138, P0158 HO2S2 .................................... .952
Component Description ....................................... .952
CONSULT-II Reference Value in Data Monitor Mode .952
On Board Diagnosis Logic ................................... .952
DTC Confirmation Procedure .............................. .953
Overall Function Check ....................................... .954
Wiring Diagram .................................................... .955
Diagnostic Procedure .......................................... .958
Component Inspection ......................................... .963
Removal and Installation ..................................... .964
DTC P0139, P0159 HO2S2 .................................... .965
Component Description ....................................... .965
CONSULT-II Reference Value in Data Monitor Mode .965
On Board Diagnosis Logic ................................... .965
DTC Confirmation Procedure .............................. .966
Overall Function Check ....................................... .967
Wiring Diagram .................................................... .968
Diagnostic Procedure .......................................... .971
Component Inspection ......................................... .974
Removal and Installation ..................................... .975
DTC P0171, P0174 FUEL INJECTION SYSTEM
FUNCTION ............................................................. .976
On Board Diagnosis Logic ................................... .976
DTC Confirmation Procedure .............................. .976
Wiring Diagram .................................................... .978
Diagnostic Procedure .......................................... .982
DTC P0172, P0175 FUEL INJECTION SYSTEM
FUNCTION ............................................................. .987
On Board Diagnosis Logic ................................... .987
DTC Confirmation Procedure .............................. .987
Wiring Diagram .................................................... .989
Diagnostic Procedure .......................................... .993
DTC P0181 FTT SENSOR ..................................... .998
Component Description ....................................... .998
On Board Diagnosis Logic ................................... .998
DTC Confirmation Procedure .............................. .998
Wiring Diagram .................................................... 1000
Diagnostic Procedure .......................................... 1001
Component Inspection ......................................... 1003
Removal and Installation ..................................... 1003
DTC P0182, P0183 FTT SENSOR ......................... 1004
Component Description ....................................... 1004
On Board Diagnosis Logic ................................... 1004
DTC Confirmation Procedure .............................. 1004 Wiring Diagram ....................................................
1005
Diagnostic Procedure ........................................... 1006
Component Inspection ......................................... 1008
Removal and Installation ...................................... 1008
DTC P0222, P0223 TP SENSOR ........................... 1009
Component Description ....................................... 1009
CONSULT-II Reference Value in Data Monitor Mode 1009
On Board Diagnosis Logic ................................... 1009
DTC Confirmation Procedure ............................... 1010
Wiring Diagram .................................................... 1011
Diagnostic Procedure ........................................... 1012
Component Inspection ......................................... 1015
Removal and Installation ...................................... 1015
DTC P0300 - P0308 MULTIPLE CYLINDER MIS-
FIRE, NO. 1 - 8 CYLINDER MISFIRE .................... 1016
On Board Diagnosis Logic ................................... 1016
DTC Confirmation Procedure ............................... 1017
Diagnostic Procedure ........................................... 1018
DTC P0327, P0328, P0332, P0333 KS .................. 1026
Component Description ....................................... 1026
On Board Diagnosis Logic ................................... 1026
DTC Confirmation Procedure ............................... 1026
Wiring Diagram .................................................... 1027
Diagnostic Procedure ........................................... 1028
Component Inspection ......................................... 1030
Removal and Installation ...................................... 1030
DTC P0335 CKP SENSOR (POS) ......................... 1031
Component Description ....................................... 1031
CONSULT-II Reference Value in Data Monitor Mode 1031
On Board Diagnosis Logic ................................... 1031
DTC Confirmation Procedure ............................... 1032
Wiring Diagram .................................................... 1033
Diagnostic Procedure ........................................... 1034
Component Inspection ......................................... 1037
Removal and Installation ...................................... 1037
DTC P0340 CAMSHAFT POSITION (CMP) SEN-
SOR (PHASE) ........................................................ 1038
Component Description ....................................... 1038
CONSULT-II Reference Value in Data Monitor Mode 1038
On Board Diagnosis Logic ................................... 1038
DTC Confirmation Procedure ............................... 1039
Wiring Diagram .................................................... 1040
Diagnostic Procedure ........................................... 1041
Component Inspection ......................................... 1044
Removal and Installation ...................................... 1044
DTC P0420, P0430 THREE WAY CATALYST FUNC-
TION ....................................................................... 1045
On Board Diagnosis Logic ................................... 1045
DTC Confirmation Procedure ............................... 1045
Overall Function Check ........................................ 1046
Diagnostic Procedure ........................................... 1047
DTC P0441 EVAP CONTROL SYSTEM ................ 1051
System Description .............................................. 1051
On Board Diagnosis Logic ................................... 1051
DTC Confirmation Procedure ............................... 1051

EC-16
[VQ35DE]
INDEX FOR DTC
Revision: 2006 July 2007 FX35/FX45
P0139 0139 HO2S2 (B1) EC-293
P0150 0150 A/F SENSOR1 (B2)EC-229
P0151 0151 A/F SENSOR1 (B2)EC-239
P0152 0152 A/F SENSOR1 (B2)EC-248
P0153 0153 A/F SENSOR1 (B2)EC-257
P0157 0157 HO2S2 (B2)EC-269
P0158 0158 HO2S2 (B2)EC-280
P0159 0159 HO2S2 (B2)EC-293
P0171 0171 FUEL SYS-LEAN-B1EC-304
P0172 0172 FUEL SYS-RICH-B1EC-316
P0174 0174 FUEL SYS-LEAN-B2EC-304
P0175 0175 FUEL SYS-RICH-B2EC-316
P0181 0181 FTT SENSOREC-327
P0182 0182 FTT SEN/CIRCUITEC-333
P0183 0183 FTT SEN/CIRCUITEC-333
P0222 0222 TP SEN 1/CIRCEC-338
P0223 0223 TP SEN 1/CIRCEC-338
P0300 0300 MULTI CYL MISFIREEC-345
P0301 0301 CYL 1 MISFIREEC-345
P0302 0302 CYL 2 MISFIREEC-345
P0303 0303 CYL 3 MISFIREEC-345
P0304 0304 CYL 4 MISFIREEC-345
P0305 0305 CYL 5 MISFIREEC-345
P0306 0306 CYL 6 MISFIREEC-345
P0327 0327 KNOCK SEN/CIRC-B1EC-355
P0328 0328 KNOCK SEN/CIRC-B1EC-355
P0335 0335 CKP SEN/CIRCUITEC-360
P0340 0340 CMP SEN/CIRC-B1EC-367
P0345 0345 CMP SEN/CIRC-B2EC-367
P0420 0420 TW CATALYST SYS-B1EC-376
P0430 0430 TW CATALYST SYS-B2EC-376
P0441 0441 EVAP PURG FLOW/MONEC-382
P0442 0442 EVAP SMALL LEAKEC-387
P0443 0443 PURG VOLUME CONT/VEC-396
P0444 0444 PURG VOLUME CONT/VEC-404
P0445 0445 PURG VOLUME CONT/VEC-404
P0447 0447 VENT CONTROL VALVE EC-411
P0448 0448 VENT CONTROL VALVEEC-418
P0451 0451 EVAP SYS PRES SENEC-424
P0452 0452 EVAP SYS PRES SENEC-427
P0453 0453 EVAP SYS PRES SENEC-433
P0455 0455 EVAP GROSS LEAKEC-441
DTC*1
Items
(CONSULT-II screen terms) Reference page
CONSULT-II
GST*
2ECM*3