key INFINITI FX35 2008 User Guide

TELEPHONEAV-167
< SERVICE INFORMATION >
C
DE
F
G H
I
J
L
M A
B
AV
N
O P
Self-Diagnosis FunctionINFOID:0000000001328794
The followings are diagnosis functions performed by TEL adapter unit.
 Performs the unit self −diagnosis and antenna diagnosis, and informs results with the indicator and voice
guidance.
 Informs vehicle speed pulse count from the time of key switch ON with voice guidance, and enables to check
vehicle speed signal.
 Outputs voice giving to microphone with speaker, and enables to check microphone function.
OPERATION PROCEDURE
1. Start the engine.
2. Press and hold switch for 5 seconds or more.
 This allows the indicator to blink concurrently with voice guidance outputs, and determines if there is any
current error in the state of blinking.
17 (R/W) Ground Remote control A Output ON Press switch
Approx. 0 V
Press SEEK UP switch Approx. 1.7 V
Press VOL UP switch Approx. 3.3 V
Except for above Approx. 5 V
18 (G/W) Ground Remote control B Output ON Press switch
Approx. 0 V
Press SEEK DOWN switch Approx. 1.7 V
Press VOL DOWN switch Approx. 3.3 V
Except for above Approx. 5 V
19 (B/Y) Ground Remote control
ground — ON — Approx. 0 V
22 (B) Ground Ground — ON — Approx. 0 V
23 (B) Ground Ground — ON — Approx. 0 V
28 (G) Ground Ve h i c l e
speed signal
(8-pulse) Input ON
When vehicle speed is ap-
prox. 40 km/h (25 MPH)
29 (W) Ground MIC. VCC Output ON — Approx. 5 V 41 — TEL signal — — — — Te r m i n a l
(Wire color) ItemSignal
input/
output Condition
Reference value
+– Ignition
switch Operation
SKIA6649J
SKIB7570E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

BCS-6
< SERVICE INFORMATION >
BCM (BODY CONTROL MODULE)
When BCM is in sleep status, transistors of OUTPUT 1 and 5 stop the output, and BCM enters low power
mode. Mean while OUTPUT 2, 3, and 4 send out ON signal every 60 ms, and accept input from lighting
switch system.
CAN COMMUNICATION CONTROL
CAN communication allows a high rate of information transmission through the two communication lines (CAN
L line, CAN H line) connecting the various control units in the system. Each control unit transmits/receives
data but selectively reads required data only. For details of signals that are transmitted/received by BCM via
CAN communication, refer to LAN-43, "
CAN System Specification Chart".
BCM STATUS CONTROL
BCM changes its status depending on the operation stat us in order to save power consumption.
1. CAN communication status  With ignition switch ON, CAN communicates with other control units normally.
 Control by BCM is being operated properly.
 When ignition switch is OFF, switching to sleep mode is possible.
 Even when ignition switch is OFF, if CAN communication with IPDM E/R and combination meter isactive, CAN communication status is active.
2. Sleep transient status  This status shuts down CAN communication when ignition switch is turned OFF.
 It transmits sleep request signal to IPDM E/R and combination meter.
 2 seconds after CAN communication of all control units stops, sleep transient status is switched to CAN
communication inactive status.
3. CAN communication inactive status  With ignition switch OFF, CAN communication is not active.
 With ignition switch OFF, control performed only by BCM is active.
 3 seconds after CAN communication of all control units stops, CAN communication inactive status is
switched to sleep status.
4. Sleep status  BCM is activated with low power mode.
 CAN communication is not active.
 When CAN communication operation is detected, it switches to CAN communication status.
 When a state of the following switches changes , it switches to CAN communication state.
- Key switch
- Hazard switch
PKIC4919E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

BCM (BODY CONTROL MODULE)BCS-7
< SERVICE INFORMATION >
C
DE
F
G H
I
J
L
M A
B
BCS
N
O P
- Door lock/unlock switch
- Front door switch (driver side, passenger side)
- Rear door switch (LH, RH)
- Back door opener switch
- Combination switch (passing, lighting switch 1ST position, front fog lamp)
- Key fob (lock/unlock signal)
- Key cylinder switch
 When control performed only by BCM is required by switch, it shifts to CAN communication inactive mode.
 Operation mode of combination switch reading function is changed.
SYSTEMS CONTROLLED BY BCM DIRECTLY
NOTE:
Power supply only. No system control.
SYSTEMS CONTROLLED BY BCM AND IPDM E/R
SYSTEMS CONTROLLED BY BCM AND COMBINATION METER
SYSTEMS CONTROLLED BY BCM AND INTELLIGENT KEY UNIT
SYSTEMS CONTROLLED BY BCM, CO MBINATION METER AND IPDM E/R
System Reference
Power door lock system BL-21
Remote keyless entry systemBL-50
Power window system NOTEGW-15
Sunroof NOTERF-10
Room lamp timerLT- 1 3 8
Rear wiper and washer systemWW-30
System Reference
Panic alarm 
BL-50
BL-76
Theft warning system BL-163
IVIS (NATS)BL-185
HeadlampLT- 5
Daytime light systemLT- 3 2
Auto light systemLT- 4 7
Front fog lampLT- 6 6
 Parking, license plate, side marker and tail lamps
 Exterior lamp battery saver control LT- 11 8
Front wiper and washer system
WW-4
Rear window defoggerGW-60
System Reference
Warning chime DI-51
Turn signal and hazard warning lampsLT- 7 8
Tire pressure monitoring systemWT-10
System Reference
Intelligent Key system BL-76
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

BCS-8
< SERVICE INFORMATION >
BCM (BODY CONTROL MODULE)
MAJOR COMPONENTS AND CONTROL SYSTEM
System Reference
Oil pressure warning lamp DI-34
System Input Output
Remote control entry system Key fob  All-door locking actuator
 Fuel lid Lock actuator
 Turn signal lamp (LH, RH)
 Combination meter
Intelligent Key system Intelligent Key unit  All-door locking actuator
 Fuel lid Lock actuator
 Turn signal lamp (LH, RH)
 Combination meter
Power door lock system  Power window main switch
(door lock and unlock switch)
 Power window sub switch (passenger side) (door lock and unlock switch) All-door locking actuator
Power supply (IGN) to power window, sunroof Ignition power supply Power window and sunroof system
Power supply (BAT) to power window, sunroof
and power seat Battery power supplyPower window, sunroof system and
power seat
Panic alarm  Key switch
 Key fobIPDM E/R
Theft warning system  All-door switch
 Hood switch
 Key fob
 Power window main switch (door lock and
unlock switch)
 Power window sub switch (passenger side) (door lock and unlock switch)  IPDM E/R
 Security indicator lamp
Auto light system  Optical sensor
 Combination switch
 Ignition switchIPDM E/R
Exterior lamp battery saver control  Ignition switch
 Combination switchIPDM E/R
Headlamp Combination switch IPDM E/R
Daytime light system  Combination meter
ECM
 Combination switch
 Ignition switchIPDM E/R
Parking, license plate, side marker and tail
lamps Combination switch IPDM E/R
Front fog lamp Combination switch IPDM E/R
Turn signal lamp  Combination switch
 Ignition switch Turn signal lamp
 Combination meter
Hazard lamp Hazard switch  Turn signal lamp
 Combination meter
Room lamp timer  Key switch
 Key fob
 Power window main switch (door lock and
unlock switch)
 Front door switch driver side
 All-door switch Interior room lamp
Key warning chime  Key switch
 Front door switch driver sideCombination meter
(warning buzzer)
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

BCM (BODY CONTROL MODULE)BCS-9
< SERVICE INFORMATION >
C
DE
F
G H
I
J
L
M A
B
BCS
N
O P
CAN Communication UnitINFOID:0000000001328609
Refer to LAN-43, "CAN System Specification Chart".
Light warning chime  Combination switch
 Key switch
 Front door switch driver sideCombination meter
(warning buzzer)
Seat belt warning chime  Combination meter [Seat belt buckle (driver
side) switch]
 Ignition switch Combination meter
(warning buzzer)
Front wiper and washer system  Combination switch
 Combination meter
 Ignition switchIPDM E/R
Rear wiper and washer system  Combination switch
 Ignition switchRear wiper motor
Rear window defogger  Rear window defogger switch
 Ignition switch
IPDM E/R
A/C switch signal Unified meter and A/C amp. ECM
Blower fan switch signal Unified meter and A/C amp. ECM
Low tire pressure warning system Remote keyless entry receiver Combination meter System Input Output
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

BCS-12
< SERVICE INFORMATION >
BCM (BODY CONTROL MODULE)
ITEMS OF EACH PART
BCM can perform the following functions for each system.
NOTE:
CONSULT-III displays systems equipped in the vehicle.
×:Applicable
NOTE:
 *1: Vehicle with remote keyless entry system display this item.
 *2: Vehicle with Intelligent Key system display this item.
 *3: This item is displayed, but does not function.
WORK SUPPORT
Display Item List
BCM Diagnostic test item Check item, diagnostic test mode Content
Inspection by part WORK SUPPORT Changes setting of each function.
SELF-DIAG RESULTS BCM performs self-diagnosis of CAN communication.
DATA MONITOR Displays the input data of BCM in real time.
CAN DIAG SUPPORT MNTR
The transmit/receive diagnosis result of CAN communication can be
read.
ACTIVE TEST Gives a drive signal to a load to check the operation.
ECU PART NUMBER ECM part number can be read.
CONFIGURATION (Not be used)
System and item CONSULT-III display Diagnostic test mode (Inspection by part)
WORK SUPPORT DATA MONITOR ACTIVE TEST
BCM BCM ×
Power door lock system DOOR LOCK ×××
Rear window defogger REAR DEFOGGER ××
Warning chime BUZZER ××
Room lamp timer INT LAMP ×××
Remote keyless entry system*
1MULTI REMOTE ENT ×××
Headlamp HEAD LAMP ×××
Wiper WIPER ×××
Turn signal lamp
Hazard lamp FLASHER
××
Blower fan switch signal
A/C switch signal AIR CONDITONER
×
Intelligent Key system*
2INTELLIGENT KEY ×
Combination switch COMB SW ×
NVIS IMMU ××
Room lamp battery saver BATTERY SAVER ×× ×
Trunk lid TRUNK*
3××
Vehicle security system THEFT ALM ×××
Retained power control RETAINED PWR ×××
Oil pressure swit ch SIGNAL BUFFER ××
Low tire pressure warning system AIR PRESSURE MONITOR ×××
Panic system PANIC ALARM ×
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

BCM (BODY CONTROL MODULE)BCS-13
< SERVICE INFORMATION >
C
DE
F
G H
I
J
L
M A
B
BCS
N
O P
SELF-DIAG RESULTS
U1000 CAN Communication CircuitINFOID:0000000001606767
1.PERFORM SELF DIAGNOSTIC
1. Turn ignition switch ON and wait for 2 seconds or more.
2. Check “Self Diagnostic Result” of BCM.
Is
“CAN COMM CIRCUIT” displayed?
YES >> Refer to LAN-14, "Trouble Diagnosis Flow Chart".
NO >> Refer to GI-25, "
How to Perform Efficient Diagnosis for an Electrical Incident".
Removal and Installation of BCMINFOID:0000000001328613
REMOVAL
1. Remove the dash side finisher (LH). Refer to EI-38.
2. Disconnect BCM connector.
3. Remove bracket mounting screws (3) to remove BCM and fuse block with bracket.
Item Description
RESET SETTING VALUE Return a value set with WORK SUPPORT of each system to a default value in factory shipment.
DTC DTC Detection Condition Possible cause
U1000: CAN COMM CIRCUIT When BCM cannot communicate CAN com-
munication signal continuously for 2 sec-
onds or more. Any item (or items) of the following listed below is
malfunctioning in CAN communication system.
Transmission
 Receiving (ECM)
 Receiving (IPDM E/R)
 Receiving (METER/M&A)
 Receiving (I-KEY)
SKIA4964E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

BCS-14
< SERVICE INFORMATION >
BCM (BODY CONTROL MODULE)
4. Raise the pawl of fuse block and remove bracket from fuse blockto remove BCM.
INSTALLATION
Installation is the reverse order of removal.
NOTE:
When replacing BCM perform initialization of NATS s ystem and registration of all NATS ignition key IDs.
SKIA4965E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

BL-1
BODY
C
DE
F
G H
J
K L
M
SECTION BL
A
B
BL
N
O P
CONTENTS
BODY, LOCK & SECURITY SYSTEM
SERVICE INFORMATION .. ..........................4
DTC INDEX ..................................................... .....4
INTELLGENT KEY UNIT U1000 ...............................4
INTELLGENT KEY UNIT B2013-B2014 ............. ......4
ECM P1610-P1615 ...................................................4
PRECAUTIONS ...................................................5
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
5
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect .....................................
5
Precaution for Work ..................................................5
PREPARATION ...................................................6
Special Service Tool ........................................... ......6
Commercial Service Tool ..........................................6
SQUEAK AND RATTLE TROUBLE DIAGNO-
SIS .......................................................................
7
Work Flow ........................................................... ......7
Generic Squeak and Rattle Troubleshooting ............9
Diagnostic Worksheet .............................................11
HOOD .................................................................13
Fitting Adjustment ............................................... ....13
Removal and Installation of Hood Assembly ...........14
Removal and Installation of Hood Lock Control ......15
Hood Lock Control Inspection ............................. ....16
RADIATOR CORE SUPPORT ...........................18
Removal and Installation ..................................... ....18
FRONT FENDER ................................................20
Removal and Installation ..................................... ....20
POWER DOOR LOCK SYSTEM ........................21
Component Parts and Harness Connector Loca-
tion ...................................................................... ....
21
System Description .................................................22
CAN Communication System Description ...............23
CAN Communication Unit .................................... ....23
Schematic/With Intelligent Key ................................24
Wiring Diagram - D/LOCK -/With Intelligent Key .....25
Schematic/Without Intellig ent Key ...........................30
Wiring Diagram - D/LOCK -/Without Intelligent
Key ...................................................................... ....
31
Terminal and Reference Value for BCM ..................35
Terminal and Reference Value for Intelligent Key
Unit (With Intelligent Key System) ...........................
35
Work Flow ................................................................36
CONSULT-III Function (BCM) .................................36
Trouble Diagnosis Chart by Symptom .....................37
Check BCM Power Supply and Ground Circuit .......37
Check Door Switch ..................................................38
Check Key Switch ....................................................42
Check Door Lock and Unlock Switch ......................43
Check Door Lock Actuator (Driver Side) .................45
Check Door Lock Actuator (Passenger Side and
Rear LH/RH) ............................................................
45
Check Fuel Lid Lock Actuator ..................................46
Check Front Door Key Cylinder Switch (Lock) ........47
Check Front Door Key Cylinder Switch (Unlock) .....47
Check Select Unlock Relay Circuit ..........................48
REMOTE KEYLESS ENTRY SYSTEM .............50
Component Parts and Harness Connector Loca-
tion ...........................................................................
50
System Description ..................................................50
CAN Communication System Description ...............53
CAN Communication Unit ........................................53
Schematic ................................................................54
Wiring Diagram - KEYLES - ....................................55
Terminal and Reference Value for BCM ..................58
Terminal and Reference Value for IPDM E/R ..........59
CONSULT-III Function (BCM) .................................60
Work Flow ................................................................62
Trouble Diagnosis Chart by Symptom .....................62
Check Key Fob Battery and Function ......................63
Check ACC Switch ..................................................64
Check Door Switch ..................................................65
Check Key Switch ....................................................68
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

BL-2
Check Remote Keyless Entry Receiver ..................69
Check IPDM E/R Operation ....................................71
Check Hazard Warning Lamp Function ..................72
Check Horn Function ..............................................72
Check Headlamp Function .....................................72
Check Map Lamp and Ignition Keyhole Illumina-
tion Function ...........................................................
72
ID Code Entry Procedure .......................................73
Removal and Installation of Remote keyless Entry
receiver ................................................................ ...
75
Key Fob Battery Replacement ................................75
INTELLIGENT KEY SYSTEM ............................76
Component Parts and Harness Connector Loca-
tion ....................................................................... ...
76
System Description .................................................78
CAN Communication System Description ..............83
CAN Communication Unit .......................................84
Schematic ...............................................................84
Wiring Diagram - I/KEY - ........................ ................86
Terminal and Reference Value for INTELLIGENT
KEY UNIT ........... ................................. ...................
99
Terminal and Reference Value for Steering Lock
unit ....................................................................... ..
101
Terminal and Reference Value for BCM ................101
Terminal and Reference Value for IPDM E/R ........102
Diagnosis Procedure .............................................103
CONSULT-III Functions (INTELLIGENT KEY) ......103
CONSULT-III Application Item ............................. ..104
List of Operation Related Parts .............................105
Trouble Diagnosis Symptom Chart ........................106
Check CAN Communication System Inspection ....111
Check Intelligent Key Unit Power Supply and
Ground Circuit ..................................................... ..
111
Check Key Switch (Intelligent Key Unit Input) .......112
Check Key Switch (BCM Input) ........................... ..113
Check Ignition Knob Switch ...................................114
Check Door Switch ................................................115
Check Unlock Sensor ............................................117
Check Door Request Switch ..................................119
Check Intelligent Key Warning Buzzer ..................120
Check Outside Key Antenna ............................... ..121
Check Inside Key Antenna ....................................123
Check Steering Lock Unit ......................................124
Check Stop Lamp Switch ......................................126
Check Park Position Switch ...................................126
Check Select Unlock Relay ...................................128
Check Hazard Function .........................................128
Check Horn Function .............................................129
Check Headlamp Function ....................................129
Check IPDM E/R Operation ...................................129
Removal and Installation of Intelligent Key Unit ....130
Intelligent Key Battery Re placement .....................130
DOOR .............................................................. .131
Fitting Adjustment ................................................ ..131
Removal and Installation of Front Door .................132
Removal and Installation of Rear Door ..................133
Removal and Installation of Door Weatherstrip .....134
FRONT DOOR LOCK .......................................135
Removal and Installation ...................................... .135
REAR DOOR LOCK .........................................138
Removal and Installation ...................................... .138
BACK DOOR .................................................. ..141
Fitting Adjustment ................................................ .141
Back Door Assembly .............................................141
Removal and Installation of Back Door Striker .....142
Removal and Installation of Back Door Stay .........143
Removal and Installation of Dave Tail Male & Fe-
male ..................................................................... .
144
Removal and Installation of Back Door Weather-
strip .......................................................................
144
BACK DOOR LOCK ASSEMBLY ....................146
Removal and Installation of Back Door Lock &
Closure Assembly ................................................ .
146
Removal and Installation of Back Door Opener
Switch ...................................................................
146
Disassembly and Assembly ..................................147
BACK DOOR AUTO CLOSURE SYSTEM ......148
Component Parts and Harness Connector Loca-
tion ....................................................................... .
148
System Description ...............................................148
Wiring Diagram - B/CLOS - ...................................150
Terminal and Reference Value for Back Door Clo-
sure Control Unit ...................................................
152
Work Flow .............................................................153
Preliminary Check .................................................153
Trouble Diagnosis Chart by Symptom ..................153
Check Back Door Closure Control Unit Power
Supply and Ground Circuit ....................................
153
Check Half-Latch Switch .......................................154
Check Close Switch ..............................................155
Check Open Switch ..............................................156
Check Back Door Opener Switch (With Intelligent
Key) ...................................................................... .
157
Check Back Door Opener Switch (Without Intelli-
gent Key) ...............................................................
159
Check Unlock Sensor (Without Intelligent Key) ....160
Check Closure Motor ........................................... .161
Removal and Installation of Back Door Closer
Control Unit ...........................................................
162
VEHICLE SECURITY (THEFT WARNING)
SYSTEM ...........................................................
163
Component Parts and Harness Connector Loca-
tion ....................................................................... .
163
System Description ...............................................164
CAN Communication System Description ............166
CAN Communication Unit .....................................166
Schematic .............................................................167
Wiring Diagram - VEHSEC - .................................168
Terminal and Reference Value for BCM ...............173
Terminal and Reference Value for IPDM E/R .......174
CONSULT-III Function ..........................................174
Trouble Diagnosis .................................................176
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C