radio INFINITI G35 2006 User Guide

(With satellite radio)
AM ! FM1 ! FM2 ! SAT1 ! SAT2 ! AM
No satellite radio reception is available
unless optional satellite receiver and an-
tenna are installed and an XM or SIRI-
US TM
satellite radio service subscription
is active.
Satellite radio is not available in Alaska
and Hawaii.
When the RADIO band select button is
pushed while the ignition switch is in the
ACC or ON position, the radio will come
on at the station last played.
The last station/channel played will also
come on when the ON z OFF/VOL control
knob is pushed to ON.
If another audio source is playing when
the RADIO button is turned to ON, the
other audio source will automatically be
turned off and the last radio station
played will come on.
The FM stereo indicator ST will glow
during FM stereo reception. When the ste-
reo broadcast signal is weak, the radio
will automatically change from stereo to
monaural reception. TUNE (Tuning):
WARNING The radio should not be tuned while driving
so full attention may be given to vehicle op-
eration.
Push these buttons for manual tuning. To
move quickly through the channels, push
and hold either of the TUNE buttons down
for more than 0.5 second.
SEEK tuning:
For AM and FM radio:
Push the SEEK button or ,to
tune from high to low or low to high fre-
quencies and stops at the next broadcast-
ing station.
For satellite radio:
Push the SEEK button or to
seek channels of the next or previous cat-
egory. SCAN tuning:
Push the SCAN tuning button to tune from
low to high frequencies and stops at each
broadcasting station for 5 seconds. Push-
ing the button again during this 5 sec-
onds period will stop SCAN tuning and
the radio will remain tuned to that sta-
tion.
If the SCAN tuning button is not pushed
within 5 seconds, SCAN tuning moves to
the next station.
DISPLAY:
O By pushing the DISP button for more
than 1.5 seconds while receiving FM
radio waves, ªPS NAMEº switches be-
tween ON and OFF (Type A only).
O Pushing the DISP button will display
additional information about the satel-
lite radio broadcast (for example:
Artist name, Title).
Keep pushing the DISP button, and it
will change the information of the sat-
ellite radio broadcast to be displayed
as follows:
CH Number ! CH Name ! Artist
Name ! Song Title ! CH Number
Display screen, heater, air conditioner and audio systems
4-23
w 06.1.4/V35-D/V5.0
X

Station memory operations:
Twelve stations/channels can be set for
the FM band (six for FM1, six for FM2),
twelve for satellite radio (six for SAT1, six
for SAT2) and six stations can be set for
the AM band.
1. Tune to the desired station using the
SEEK, SCAN or TUNE button.
2. Select the desired station/channel
and keep pushing any of the desired
station preset buttons (1 to 6) until a
beep sound is heard. (The radio mutes
when the select button is pushed.)
3. The channel indicator will then come
on and the sound will resume. Memo-
rizing is now complete.
4. Other buttons can be set in the same
manner.
If the battery cable is disconnected, or if
the fuse blows, the preset station memory
will be erased. In that case, reset the de-
sired stations.
Automatic preset:
To select the preset FM, AM, SAT or PTY
station/channel, push the AUTO.P button
for less than 1.5 seconds. To preset the FM, AM, SAT or PTY
station/channel, push the AUTO.P button
for more than 1.5 seconds.
Program type/category (Type A)
Repeat/category (Type B):
When the PTY button is pushed for more
than 1.5 seconds during FM mode, the PTY
name of the current tuned station is dis-
played (Type A only). During this time if
the PTY data code is zero, or the data is
unreadable; the display will show NONE.
When the PTY (CAT) Ð type A, or RPT (CAT)
Ð Type B, button is pushed for more than
1.5 seconds during the satellite radio
mode, the category name of the current
channel is displayed.
1. PTY (CAT) selection mode
PTY (CAT) name selection can be done
by the up/down TUNE button or
in the PTY (CAT) selection mode.
It is possible to shift the PTY (CAT) name
by one step, with one push of the
up/down tuning button or .
PTY name selection can also be achieved
by pushing the preset buttons.
Initial PTY names are stored in the station preset buttons; but these can be changed
by pushing the station preset buttons for
more than 1.5 seconds when the desired
PTY name is in the display.
2. PTY SEEK tuning mode
After selecting a PTY name, push the
SEEK button or within 10
seconds. Tuning to the PTY station will
start. If you do not push the SEEK but-
ton within the 10 second period, the
PTY mode will be canceled.
4-24 Display screen, heater, air conditioner and audio systems
w 06.1.4/V35-D/V5.0
X

3. PTY SCAN tuning mode
Push the SCAN tuning button to tune
the PTY name station, and stop at
each broadcasting station for 5 sec-
onds. Pushing the button again during
this 5 second period will stop SCAN
tuning and the radio will remain tuned
to that station. If the SCAN tuning but-
ton is not pushed within 5 seconds,
SCAN tuning moves to the next sta-
tion.
Compact disc (CD) changer
operation Turn the ignition switch to the ACC or ON
position, push the LOAD button and insert
the compact disc into the slot with the la-
bel side facing up. The CD will be guided
automatically into the slot and start play-
ing.
After loading the disc, the number of
tracks on the disc and the play time will
appear on the display.
If the radio is already operating, it will au-
tomatically turn off and the CD will play. CAUTION O Do not force the compact disc into the
slot. This could damage the player.
O Do not use 3.1 in (8 cm) discs.
If the system has been turned off while
the CD was playing, pushing the
ON z OFF/VOL control button will start the
compact disc.
CD LOAD:
To insert a CD in the CD changer, push
the LOAD button for less than 1.5 sec-
onds. Select the loading slot by pushing
the CD insert select button (1 to 6), then
insert the CD.
To insert 6 CDs to the CD changer in suc-
cession, push the LOAD button for more
than 1.5 seconds.
The inserted slot numbers will illuminate
on the display.
PLAY:
When the CD button is pushed with the
system off and the compact disc loaded,
the system will turn on and the compact
disc will start to play. When the CD button is pushed with the
CD loaded with the radio playing, the
radio will automatically be turned off and
the compact disc will start to play.
DISPLAY:
When the display button is pushed for
more than 1.5 seconds while the CD is be-
ing played, the music information dis-
played can be changed in the following
order.
CD:
CD with MP3 or WMA:
FF (Fast Forward), REW
(Rewind):
CD:
When the (fast forward) or (re-
wind) button is pushed while the compact
disc is being played, the CD will play
while fast forwarding or rewinding. When
Display screen, heater, air conditioner and audio systems
4-25
w 06.1.4/V35-D/V5.0
X

1. VOLUME control switch
2. POWER on/off switch
3. MODE select switch
4. Tuning switch
5. POWER on/MODE select switch
STEERING WHEEL SWITCH FOR
AUDIO CONTROL The audio system can be operated using
the controls on the steering wheel.
POWER on/off switch With the ignition switch turned to the ACC
or ON position, push the POWER switch to
turn the audio system on or off.
MODE select switch Push the MODE select switch to change
the mode in the sequence of AM, FM1,
FM2, SAT1 (if so equipped), SAT2 (if so
equipped) and CD.
Pushing this switch also turns the audio
system on when it is off.
POWER on/MODE select switch (if
so equipped) With the ignition switch turned to the ACC
or ON position, push the POWER
on/MODE select switch to turn the audio system on. Push the switch to change the
mode in the sequence of AM, FM1, FM2,
SAT1 (if so equipped), SAT2 (if so
equipped) and CD.
VOLUME control switch Push up/down the VOLUME control switch
to increase or decrease the volume.
Tuning switch Memory change (radio):
Push up/down the tuning switch or
for less than 1.5 seconds to change
the radio frequency.
SEEK tuning (radio):
Push up/down the tuning switch or
for more than 1.5 seconds to seek
the next or previous radio station.
APS (Automatic Program Search) FF, APS
REW (CD):
Push up/down the tuning switch or
for less than 1.5 seconds to return to
the beginning of the present program or
skip to the next program. Push several
times to skip back or skip through pro-
grams.SAA0974
Type A
SAA1349
Type B
4-28 Display screen, heater, air conditioner and audio systems
w 06.1.4/V35-D/V5.0
X

This system searches for the blank inter-
vals between selections. If there is a
blank interval within one program or there
is no interval between programs, the sys-
tem may not stop in the desired or ex-
pected location.
FOLDER change (CD with MP3/WMA):
Push up/down the tuning switch or
for more than 1.5 seconds to change
the folders (if it has folders).
Push up/down the tuning switch or
for less than 1.5 seconds to return to
the beginning of the present program or
skip to the next program.
DISC change (CD without MP3/WMA):
Push up/down the tuning switch or
for more than 1.5 seconds to change
the playing disc up or down.
ANTENNA
Window antenna The antenna pattern is printed inside the
rear window. CAUTION O Do not place metalized film near the rear
window glass or attach any metal parts
to it. This may cause poor reception or
noise.
O When cleaning the inside of the rear win-
dow, be careful not to scratch or damage
the rear window antenna. Lightly wipe
along the antenna with a dampened soft
cloth. When installing a CB, ham radio or car
phone in your INFINITI, be sure to observe
the following cautions, otherwise the new
equipment may adversely affect the En-
gine control system and other electronic
parts.
WARNING O A cellular telephone should not be used
while driving so full attention may be
given to vehicle operation. Some juris-
dictions prohibit the use of cellular tele-
phones while driving.
O If you must make a call while your ve-
hicle is in motion, the hands free cellular
phone operational mode (if so equipped)
is highly recommended. Exercise ex-
treme caution at all times so full atten-
tion may be given to vehicle operation.
O If a conversation in a moving vehicle re-
quires you to take notes, pull off the road
to a safe location and stop your vehicle
before doing so.CAR PHONE OR CB RADIO
Display screen, heater, air conditioner and audio systems
4-29
w 06.1.4/V35-D/V5.0
X

CAUTIONO Keep the antenna as far away as pos-
sible from the electronic control mod-
ules.
O Keep the antenna wire more than 8 in
(20 cm) away from the electronic control
system harness. Do not route the an-
tenna wire next to any harness.
O Adjust the antenna standing-wave ratio
as recommended by the manufacturer.
O Connect the ground wire from the CB
radio chassis to the body.
O For details, consult an INFINITI dealer.
WARNING O Use a phone after stopping your vehicle
in a safe location. If you have to use a
phone while driving, exercise extreme
caution at all times so full attention may
be given to vehicle operation.
O If a conversation in a moving vehicle re-
quires you to take notes, pull off the road
to a safe location and stop your vehicle
before doing so.
CAUTION To avoid draining the vehicle battery, use a
phone after starting the engine.BLUETOOTH HANDS-FREE PHONE SYSTEM
WITH INFINITI VOICE RECOGNITION
4-30 Display screen, heater, air conditioner and audio systems
w 06.1.4/V35-D/V5.0
X

Ð Your vehicle is in an area where it
is difficult to receive radio waves;
such as in a tunnel, in an under-
ground parking garage, near a tall
building or in a mountainous area.
Ð Your cellular phone is locked to
prevent it from being dialed.
When the radio wave condition is not
ideal or ambient sound is too loud, it may
be difficult to hear the other person's
voice during a call.
Do not place the cellular phone in an area
surrounded by metal or far away from the
in-vehicle phone module to prevent tone
quality degradation and wireless connec-
tion disruption.
While a cellular phone is connected
through the Bluetooth wireless connec-
tion, the battery power of the cellular
phone may discharge quicker than usual.
If the Bluetooth Hands-Free Phone
System seems to be malfunctioning,
please refer to ªTroubleshooting guideº
later in this section. You can also visit
www.infiniti.com/bluetooth for trouble-
shooting help. Refer to the cellular phone Owner's
Manual regarding the telephone charges,
cellular phone antenna and body, etc.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) this device may
not cause harmful interference, and (2)
this device must accept any interference
received, including interference that may
cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radia-
tion exposure limits set forth for an un-
controlled environment. This equipment
should be installed and operated with
minimum distance 8 inch (20 cm) be-
tween the radiator and your body. This
Transmitter must not be co-located or op-
erating in conjunction with any other an-
tenna or transmitter.
USING THE SYSTEM The INFINITI Voice Recognition system al-
lows hands-free operation of the
Bluetooth Hands-Free Phone System.
If the vehicle is in motion, some com-
mands may not be available so full atten-
tion may be given to vehicle operation. Initialization When the ignition switch is turned to the
ON position, INFINITI Voice Recognition is
initialized, which takes a few seconds.
When completed, the amber light on the
overhead console illuminates and the
system is ready to accept voice com-
mands. If the button is pushed be-
fore the initialization completes, the
system will announce ªHands-free phone
system not readyº and will not react to
voice commands.
Operating tips To get the best performance out of the
INFINITI Voice Recognition system, ob-
serve the following:
O Keep the interior of the vehicle as
quiet as possible. Close the windows
to eliminate surrounding noises
(traffic noises, vibration sounds, etc.),
which may prevent the system from
recognizing voice commands correctly.
O Wait until the tone sounds before
speaking a command. Otherwise, the
command will not be received properly.
O Start speaking a command within 5
seconds after the tone sounds.
4-32 Display screen, heater, air conditioner and audio systems
w 06.1.4/V35-D/V5.0
X

O Speak in a natural voice without paus-
ing between words.
Giving voice commands To operate INFINITI Voice Recognition,
push and release the button located
on the steering wheel. The light on the
overhead console flashes to signal you
have entered a voice recognition (VR) ses-
sion. After the tone sounds, speak a com-
mand.
The command given is picked up by the
microphone, and voice feedback is given
when the command is accepted.
O If you need to hear the available com-
mands for the current menu again, say
ªHelpº and the system will repeat
them.
O If a command is not recognized, the
system announces, ªCommand not
recognized. Please try again.º Repeat
the command in a clear voice.
O If you want to go back to the previous
command, you can say ªGo backº or
ªCorrectionº anytime the system is
waiting for a response.
O You can cancel a command when the
system is waiting for a response by saying, ªCancelº or ªQuit.º The system
announces ªCancelº and ends the VR
session. You can also push the
button on the steering wheel at
any time. Whenever the VR session is
cancelled, a double beep is played to
indicate you have exited the system.
O If you want to adjust the volume of the
voice feedback, push the volume con-
trol switches (+ or -) on the steering
wheel while being provided with feed-
back. You can also use the radio
volume control knob.
How to say numbers
INFINITI Voice Recognition requires a cer-
tain way to speak numbers in voice com-
mands. Refer to the rules and examples
below.
O Either ªzeroº or ªohº can be used for
ª0º.
Example: 1-800-662-6200
Ð ªOne eight oh oh six six two six two
oh ohº, or
Ð ªOne eight zero zero six six two six
two oh ohº
O Words can be used for the first 4 dig-
its places only. Example: 1-800-662-6200
Ð ªOne eight hundred six six two six
two oh ohº,
Ð NOT ªOne eight hundred six six two
sixty two hundred, and
Ð NOT ªOne eight oh oh six six two
sixty two hundred.
O Numbers can be spoken in small
groups. The system will prompt you to
continuing entering digits, if desired.
Example: 1-800-662-6200
Ð ªOne eight oh ohº
The system repeats the numbers and
prompts you to enter more.
Ð ªsix six twoº
The system repeats the numbers and
prompts you to enter more.
Ð ªsix two oh ohº
O You can say ªStarº for * and ªPoundº
for # at anytime in any position of the
phone number.
Example: 1-555-1212 *123
Ð ªOne five five five one two one two
star one two threeº
Display screen, heater, air conditioner and audio systems
4-33
w 06.1.4/V35-D/V5.0
X

The ignition lock is designed so that the
ignition switch cannot be turned to the
LOCK position and removed until the se-
lector lever is moved to the P (Park) posi-
tion.
When turning the ignition switch, make
sure the selector lever is in the P position.
If the selector lever is not returned to the
P position, the ignition switch cannot be
moved toward the LOCK position.
When the ignition switch cannot be
turned toward the LOCK position, proceed
as follows: 1. Move the selector lever into the P po-
sition.
2. Turn the ignition switch slightly in the
ON direction.
3. Turn the key toward the LOCK posi-
tion.
The selector lever can be moved from the P
position if the ignition switch is in the ON
position and the foot brake pedal is de-
pressed.
There is an OFF position in between the
LOCK and ACC positions, although it does
not show on the lock cylinder. When the
ignition is in the OFF position the steering
wheel is not locked.
In order for the steering wheel to be
locked, it must be turned about 1/6 of a
turn counterclockwise from the straight
up position.
To lock the steering wheel, turn the igni-
tion switch to the LOCK position. To unlock
the steering wheel, push the ignition
switch in and turn it gently while rotating
the steering wheel slightly right and left.
If the battery of the vehicle equipped with
the Intelligent Key system is discharged,
the ignition switch cannot be turned from the LOCK position, even using the me-
chanical key or valet key.
WARNING Never turn the ignition switch to the LOCK
position while driving. The steering wheel
will lock. This may cause the driver to lose
control of the vehicle and could result in se-
rious vehicle damage and/or personal injury.
IGNITION SWITCH POSITIONS Push in the ignition switch to the
q B
range when you turn it.
LOCK (Normal parking position):
The ignition switch can only be locked in
the
q A
position.
The ignition switch will be unlocked when
it is pushed in, and turned to the ACC po-
sition
q D
while carrying the Intelligent
Key.
ACC (Accessories)
q D
:
This position activates electrical accesso-
ries such as the radio, when the engine is
not running.SPA1628
IGNITION SWITCH (models with the
Intelligent Key system)
Starting and driving
5-9
w 06.1.4/V35-D/V5.0
X

REMOVING SPOTS Remove tar and oil spots, industrial dust,
insects, and tree sap as quickly as pos-
sible from the surface of the paint to
avoid lasting damage or staining. Special
cleaning products are available at an
INFINITI dealer or any automotive acces-
sory store.
UNDERBODY In areas where road salt is used in winter,
the underbody must be cleaned regularly.
This will prevent dirt and salt from
building up and causing underbody and
suspension corrosion. Before the winter
period and again in the spring, the under-
seal must be checked and, if necessary,
re-treated.
GLASS Use glass cleaner to remove smoke and
dust film from the glass surfaces. It is
normal for glass to become coated with a
film after the vehicle is parked in the hot
sun. Glass cleaner and a soft cloth will
easily remove this film. CAUTION When cleaning the inside of the windows, do
not use sharp-edged tools, abrasive
cleaners or chlorine-based disinfectant
cleaners. They could damage the electrical
conductors, radio antenna elements or rear
window defroster elements.
ALUMINUM ALLOY WHEELS Wash regularly, especially during winter
months in areas where road salt is used.
Salt could discolor the wheel if not re-
moved.
CHROME PARTS Clean all chrome parts regularly with a
non-abrasive chrome polish to maintain
the finish.
TIRE DRESSING INFINITI does not recommend the use of
tire dressings. Tire manufacturers apply a
coating to the tires to help reduce discol-
oration of the rubber. If a tire dressing is
applied to the tires, it may react with the
coating and form a compound. This com- pound may come off the tire while driving
and stain the vehicle paint.
If you choose to use a tire dressing, take
the following precautions:
O Use a water-based tire dressing. The
coating on the tire dissolves more
easily with an oil-based tire dressing.
O Apply a light coat of tire dressing to
help prevent it from entering the tire
tread/grooves (where it would be diffi-
cult to remove).
O Wipe off excess tire dressing using a
dry towel. Make sure the tire dressing
is completely removed from the tire
tread/grooves.
O Allow the tire dressing to dry as rec-
ommended by tire dressing manufac-
turer.
Appearance and care
7-3
w 06.1.4/V35-D/V5.0
X