lights INFINITI JX 2013 Quick Reference Guide

2
new system features
Remote Engine Start* (if so equipped)
your INfINITI Intelligent Key™ system allows the engine to start from
outside your vehicle. To use the remote start feature, perform the following:

1. Aim the INfINITI Intelligent Key at the vehicle. Operating range
is approximately 197 feet (60 m) from the vehicle.
2. Press the

button
01 to lock all doors.

3. Within 5 seconds press and hold the remote start

button
02
until the turn signal lights illuminate. If the vehicle is not within

view, press and hold the remote start button for about 2 seconds.

The parking lights will turn on and remain on as long as the engine
is running. The doors will be locked and the climate control system
may come on.

Repeat steps 1 - 3 to extend time an additional 10 minutes. A maximum of two remote starts,
or a single start with an extension, are allowed between ignition cycles.


Depress the brake and place the ignition switch in the ON position before driving.

To cancel a remote start, perform one of the following:
•
Aim the Intelligent Key at the vehicle and press and hold the

button until the parking
lights turn off.
•
Turn the hazard warning flashers on.
•
Cycle the ignition switch ON and then OFF.
*Laws in some communities may restrict the use of remote starters. Check local regulations before using this feature.
for more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
INFINITI Connection™ System* (if so equipped)
Infiniti Connection provides various types of information
and services by connecting your vehicle to the Infiniti
Connection Data Center. f or more details on the Infiniti
Connection service, terms and conditions, please refer
to www.Infiniticonnection.com.
Available services include:

Infiniti Personal Assistant – To access Infiniti Personal
Assistant, select “Connect to Voice Menu” from the Infiniti Connection menu or touch the


key (if available on the map screen). At the voice prompt, say “Infiniti Personal Assistant” to
be connected.
• your Infiniti Personal Assistant can send destination information directly to your vehicle.
To access, go to the Infiniti Connection menu and select “Sync All Information f eeds”.
Then go to the feeds menu page and download the desired destination information.

Automatic Collision Notification – In case of air bag deployment, a signal is sent containing
the vehicle location and customer information and notifies the proper authorities.
01
02
*Infiniti Connection™ is only available on vehicles equipped with optional Infiniti Connection™ subscription service.

3


Emergency Call (if so equipped) – This service provides emergency assistance by connecting
subscriber to an Infiniti Connection Specialist.
• In case of an emergency, press the in-vehicle
telematics SOS button

01 .
• A Response Specialist will provide assistance based
on the situation described by the vehicle’s occupant.

Enhanced Roadside Assistance (if so equipped) –
Roadside Assistance can be accessed by touching
the Infiniti Connection key on the Info menu, the

key (if available on the map screen) or by pressing the
SOS button.
• This service allows subscribers to receive assistance for a non-emergency incident such as
towing or a third party response.
• If warranted, Roadside Assistance may also be used in conjunction with the Emergency
Assistance service by pressing the SOS button.

My Schedule – Access your personal online Google Calendar™, hear details read via text-to-
speech** and select locations as a destination via the navigation system.

Report Stolen Vehicle – A Response Specialist will attempt to obtain location information
from a reported stolen vehicle and provide that information to local law enforcement agencies
to assist in the recovery of your stolen vehicle.

Remote Door Lock/Unlock – Remotely access your vehicle via Infiniti Connection Response
Specialist or designated website to remotely lock or unlock your vehicle.

Alarm Notification – This system will notify you when the factory-installed vehicle alarm
system has been activated.

Scheduled Maintenance Notification – Receive scheduled maintenance notifications based
on mileage data provided by your vehicle.

Maintenance Alert – Receive notification of a vehicle system malfunction that triggers
instrument panel warning lights.

Destination Assistance – Receive point-of-interest assistance via guided IVR (Interactive
Voice Response), Response Specialist, or Infiniti Connection web portal.

Destination Send-to Vehicle – find and download point-of interest information from
GoogleMaps™.

Connected Search – Select “Connected Search” from the Destination menu on the vehicle’s
navigation system to conduct a point-of-interest search within a certain distance of the
vehicle’s location.

Drive Zone – Monitor the movement of your vehicle within a specified region. Set up boundaries
in the Monitoring section of the Infiniti Connection web portal.

Max Speed Alert – Set up a maximum speed on the Infiniti Connection web portal. you will
receive notifications if your vehicle exceeds the max speed setting.
01
**Laws in some communities may restrict the use of text-to-speech. Check local regulations before using this feature.

essential information
Loose Fuel Cap
A LOOSE FUEL CAP warning message will appear
in the vehicle information display

01 when the
fuel-filler cap is not tightened correctly.

To tighten, turn the cap clockwise until a single click
is heard.

The warning message will disappear when the vehicle
detects the fuel-filler cap is properly tightened and the
reset button

02 is pressed for about 1 second.

If the cap is not properly tightened, the Malfunction
Indicator Light

may illuminate.
f
or more information, refer to the “Instruments and controls (section 2)”
and the “Pre-driving checks and adjustments (section 3)” of your
Owner’s Manual.
Tire Pressure Monitoring System (TPMS) with Tire Inflation Indicator
A Tire Pressure Low - Add Air warning message will
appear in the vehicle information display

01 and the

low tire pressure warning light
02 will illuminate when

one or more tires are low on pressure and air is needed.
• The tire pressures should be checked when the
tires are cold. The tires are considered cold after
the vehicle has been parked for 3 hours or more or
driven less than 1 mile (1.6km) at moderate speeds.

When adding air to an under-inflated tire, the TPMS
with Tire Inflation Indicator provides visual and
audible signals to help you inflate the tires to the
recommended COLD tire pressure.
To use the tire inflation indicator:
1. Move the shift lever to the P (PARK) position and apply the parking brake.
2. Place the ignition switch in the ON position. Do not start the engine.
3. Add air to the under-inflated tire and within a few seconds, the hazard warning lights will start
flashing.
4. When the designated tire pressure is reached, the horn will beep once and the hazard warning
flashers will stop flashing.
5. Repeat this procedure for any additional under-inflated tires.

After tire pressures are adjusted, drive the vehicle at speeds above 16 MPH (25km/h). The
Tire Pressure Low - Add Air warning message and low tire pressure warning light will disappear.

When the low tire pressure warning light flashes for approximately 1 minute and then remains
on, the TPMS is not functioning properly. Have the system checked by an INfINITI retailer.
01
01
02
7
02

9
INFINITI Intelligent Key™ System
The INfINITI Intelligent Key™ system allows you to lock or unlock your
vehicle, open your liftgate and remotely start the engine.
NOTE: It is important to make sure the Intelligent Key is with you (that is,
in your pocket or purse).
REMOTE ENGINE START (if so equipped)

The remote engine start operating range is approximately 197 feet
(60 m) from the vehicle.

To use the remote start feature to start the engine:
1. Aim the Intelligent Key at the vehicle.
2. Press the

button
01 to lock all doors.

3. Within 5 seconds press and hold the remote start

button
02 until the turn signal lights

illuminate. If the vehicle is not within view, press and hold the remote start button for about
2 seconds.
LOCKING AND UNLOCKING THE VEHICLE

The lock and unlock operating range of the Intelligent
Key is within 31.5 in (80 cm) from each request switch.

To lock the vehicle, push either door handle request
switch

03 once or press the
button
01 on the keyfob.

To unlock the vehicle, perform one of the following
procedures:
• Push either door handle request switch

03 once; the corresponding door will unlock. Push

the door handle request switch
again within 30 seconds; all
other doors will unlock, or
• Press the

button
04 on the keyfob to unlock the driver’s side door. Press the
button

again; all other doors will unlock.
LIf TGATE RELEASE

To open the rear liftgate, press the
button
05 for longer than 0.5 seconds.


To close the rear liftgate, press the
button
05 again for longer than 0.5 seconds.

PANIC ALARM

The Intelligent Key can also be used to activate the panic alarm by pressing and holding the

button
06 for more than 1 second. Once activated, the panic alarm and headlights will
stay on for 25 seconds.
first drive features
02
01
04
05
06
03

14
first drive features
Headlight Control Switch
HEADLIGHT CONTROL

Turn the headlight control switch to the position

01 to turn on the front parking, tail, license plate and
instrument panel lights. Turn the switch to the


position
02 to turn on the headlights.
AUTOLIGHT S ySTEM

The autolight system will automatically turn the headlights on when it is dark and off when it is
light. The system will keep the headlights on for a period of time after you turn the ignition off
and all doors are closed.

To activate the autolight system, turn the headlight control switch to the AUTO position
03
then push the ignition switch to ON. To deactivate the autolight system, turn the headlight

control switch to the OFF,

01 or
position
02 .

HIGH BEAM SELECT

Push the headlight control switch forward
04 to
select the high beam function. The blue indicator light

illuminates in the instrument panel. Pull the
headlight switch back to the original position to
select the low beam. The blue indicator light goes off.

Pull and release the headlight control switch
05 to
flash the headlight high beams on and off.
fOG LIGHT SWITCH
NOTE: The headlights must be on and the low beams

selected for the fog lights to operate.

Turn the switch (inside collar) to the position
06
to turn the fog lights on.

Turn the switch (inside collar)
to the OFF position to
turn the fog lights off.
for more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
03
04
06
01
05
02

20
first drive features
Intelligent Cruise Control (ICC) System (if so equipped)
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE

To set Vehicle-To-Vehicle Distance Control mode,
press the CRUISE ON/OFF button

01 for less than 1.5
seconds. The CRUISE indicator light
02 will illuminate.

Accelerate to the desired speed.

Push down on the COAST/SET switch
03 and release
it. Cruise control will be set to the desired speed.

Press the distance button
04 repeatedly to change
the set distance between long, middle, and short.

When a vehicle is not detected ahead of you in the
lane, the set distance and set vehicle speed indicator
lights will illuminate

05 in set mode.

When a vehicle is detected ahead of you in the lane,
the vehicle ahead detection, set distance, and set
vehicle speed indicator lights will illuminate

06 in set mode.

To reset at a faster cruising speed, push and hold the ACCEL/RES
switch

07 . When the vehicle attains the desired speed, release the switch.

To reset at a slower cruising speed, push and hold the COAST/SET switch


03 . Release the switch when the vehicle slows to the desired speed.

To cancel the preset speed, push the CANCEL switch
08 or tap the brake pedal. The set
vehicle speed indicator
05 will go out.

To turn off cruise control, press the CRUISE ON/OFF button
01 . The
CRUISE indicator light

02 , in the instrument panel, will turn off.
To set conventional (fixed speed) cruise control mode:

While cruise control is off, press the CRUISE ON/OFF
button
01 and hold it down for more
than 1.5 seconds. The CRUISE indicator light will illuminate.

Accelerate to the desired speed.

Push down on the COAST/SET switch and release it. The SET indicator light will illuminate.
Cruise control will be set to the desired speed.
To switch between the two cruise control modes:

When one of the two cruise modes is in use, you must turn the system off, and then turn it on
again to select the other cruise control mode.
for more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
01
0403
0708
0205
06

To cancel the preset speed, push the CANCEL switch
04 .

To turn off cruise control, push the CRUISE
ON/OFF switch
01 . Both the
CRUISE indicator

light
and the SET
indicator light in the instrument panel will turn off.
for more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.

30
system guide
HomeLink® Universal Transceiver (if so equipped)
The HomeLink® system can learn and consolidate the functions of up to three different hand-
held transmitters, operating items such as garage doors, property gates, outdoor and indoor
lights or alarm systems.
for more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual, the HomeLink® website at
www.homelink.com or call 1-800-355-3515.
HOMELINk®