recommended oil INFINITI M 2010 Owners Manual

CAUTION
During the first 1,200 miles (2,000 km), follow
these recommendations to obtain maximum
engine performance and ensure the future reli-
ability and economy of your new vehicle. Fail-
ure to follow these recommendations may re-
sult in shortened engine life and reduced
engine performance.
c Avoid driving for long periods at constant
speed, either fast or slow. Do not run the
engine over 4,000 rpm.
c Do not accelerate at full throttle in any gear.
c Avoid quick starts.
c Avoid hard braking as much as possible. c
Accelerate slowly and smoothly. Maintain
cruising speeds with a constant accelerator
position.
c Drive at moderate speeds on the highway.
Driving at high speed lowers fuel economy.
c Avoid unnecessary stopping and braking.
Keep a safe distance behind other vehicles.
c Select a gear range suitable to road condi-
tions.
c Avoid unnecessary engine idling.
c Keep your engine tuned up.
c Follow the recommended periodic mainte-
nance schedule.
c Keep the tires inflated to the correct pres-
sure. Low tire pressure increases tire wear
and lowers fuel economy.
c Keep the wheels in correct alignment. Im-
proper alignment increases tire wear and
lowers fuel economy.
c Climate control operation lowers fuel
economy. Use the air conditioner only when
necessary.
c When cruising at highway speeds, it is more
economical to use the air conditioner and
leave the windows closed to reduce drag. c
Use the recommended viscosity engine oil.
(See ªENGINE OIL AND OIL FILTER RECOM-
MENDATIONº in the ª9. Technical and con-
sumer informationº section.)
BREAK-IN SCHEDULE INCREASING FUEL ECONOMY
5-46Starting and driving
wÐ
Ð
05/15/09Ðpattie
X

Installing the spare tire
The spare tire is designed for emergency use.
(See specific instructions under the heading
ªWHEELS AND TIRESº in the ª8. Maintenance
and do-it-yourselfº section.)
1. Clean any mud or dirt from the surfacebetween the wheel and hub.
2. Carefully put the spare tire on and tighten the wheel nuts finger tight. Check that all
the wheel nuts contact the wheel surface
horizontally.
3. With the wheel nut wrench, tighten wheel nuts alternately and evenly in the se-
quence as illustrated (
s1,s2,s3,s4,s5),
more than 2 times, until they are tight. 4. Lower the vehicle slowly until the tire
touches the ground. Then, with the wheel
nut wrench, tighten the wheel nuts se-
curely in the sequence as illustrated.
Lower the vehicle completely.
WARNING
cIncorrect wheel nuts or improperly tightened
wheel nuts can cause the wheel to become
loose or come off. This could cause an
accident.
c Do not use oil or grease on the wheel studs or
nuts. This could cause the nuts to become
loose.
c Retighten the wheel nuts when the vehicle
has been driven for 600 miles (1,000 km)
(also in cases of a flat tire, etc.). c
As soon as possible, tighten the wheel nuts
to the specified torque with a torque wrench.
Wheel nut tightening torque: 80 ft-lb (108 N´m)
The wheel nuts must be kept tightened to speci-
fication at all times. It is recommended that
wheel nuts be tightened to specifications at
each lubrication interval.
c Adjust tire pressure to the COLD pressure.
COLD pressure:
After the vehicle has been parked for three
hours or more or driven less than 1 mile
(1.6 km).
COLD tire pressures are shown on the Tire
and Loading Information label affixed to the
driver side center pillar.
After adjusting tire pressure to the COLD tire
pressure, the display of the tire pressure infor-
mation may show higher pressure than the
COLD tire pressure after the vehicle has been
driven more than 1 mile (1.6 km). This is be-
cause the tire pressurizes as the tire tempera-
ture rises. This does not indicate a system
malfunction.
SCE0039
6-6In case of emergency
wÐ
Ð
05/15/09Ðpattie
X

CHECKING ENGINE OIL LEVEL
1. Park the vehicle on a level surface andapply the parking brake.
2. Run the engine until it reaches operating temperature.
3. Turn off the engine. Wait more than 15
minutes for the oil to drain back into the oil
pan.
4. Remove the dipstick and wipe it clean. Reinsert it all the way.
5. Remove the dipstick again and check the oil level. It should be within the range
s1.
If the oil level is below
s2, remove the oil
filler cap and pour recommended oil
through the opening. Do not overfill
s3.
6. Recheck oil level with the dipstick.
It is normal to add some oil between oil mainte-
nance intervals or during the break-in period,
depending on the severity of operating condi-
tions.
CAUTION
Oil level should be checked regularly. Operat-
ing the engine with an insufficient amount of oil
can damage the engine, and such damage is
not covered by warranty.
CHANGING ENGINE OIL AND FILTER
Change the engine oil and filter according to the
maintenance intervals shown in the INFINITI
Service and Maintenance Guide.
Vehicle set-up
1. Park the vehicle on a level surface and apply the parking brake.
2. Run the engine until it reaches operating temperature.
3. Turn the engine off and wait more than 15 minutes.
4. Raise and support the vehicle using a suitable floor jack and safety jack stands.
cPlace the safety jack stands under the
vehicle jack-up points.
c A suitable adapter should be attached to
the jack stand saddle.
5. Remove the plastic engine undercover.
a. Remove the small plastic clip at the center
point of the undercover.
b. Then remove the other bolts that hold the undercover in place.
VK45DE engine
SDI1822
VQ35HR engine
SDI2045
ENGINE OIL
8-12Maintenance and do-it-yourself
wÐ
Ð
05/19/09Ðtbrooks
X

Engine oil and filter
1. Place a large drain pan under the drainplug.
2. Remove the oil filler cap.
3. Remove the drain plug
s1with a wrench
and completely drain the oil.
CAUTION
Be careful not to burn yourself, as the engine oil
is hot.
cWaste oil must be disposed of properly.
c Check your local regulations.
Perform steps 4 to 7 only when the engine oil
filter change is needed.
4. Loosen the oil filters2with an oil filter
wrench. Remove the oil filter by turning it
by hand.
5. Wipe the engine oil filter mounting sur- face with a clean rag.
CAUTION
Be sure to remove any old rubber gasket re-
maining on the mounting surface of the engine.
Failure to do so could lead to engine failure.
6. Coat the gasket on the new filter with clean engine oil.
7. Screw in the oil filter clockwise until a slight resistance is felt, then tighten ad-
ditionally more than 2/3 turn.
Oil filter tightening torque:11 to 15 ft-lb
(14.7 to 20.5 N´m)
8. Clean and re-install the drain plug with a new washer. Securely tighten the drain
plug with a wrench.
Drain plug tightening torque:22 to 29 ft-lb
(29 to 39 N´m)
Do not use excessive force.
9. Refill engine with recommended oil and install the oil filler cap securely.
CAUTION
The dipstick must be inserted in place to pre-
vent oil spillage from the dipstick hole while
filling the engine with oil.
See ªCAPACITIES AND RECOMMENDED
FUEL/LUBRICANTSº in the ª9. Technical and
consumer informationº section for drain and refill capacity. The drain and refill capacity
depends on the oil temperature and drain time.
Use these specifications for reference only.
Always use the dipstick to determine the proper
amount of oil in the engine.
10. Start the engine and check for leakage
around the drain plug and the oil filter.
Correct as required.
11. Turn the engine off and wait more than 15 minutes. Check the oil level with the
dipstick. Add engine oil if necessary.
After the operation
1. Install the engine undercover into positionas the following steps.
a. Pull the center of the small plastic clip out.
b. Hold the engine undercover into position.
c. Insert the clip through the undercover into the hole in the frame, then push the
center of the clip in to lock the clip in
place.
d. Install the other bolts that hold the un- dercover in place. Be careful not to strip
the bolts or over-tighten them.
2. Lower the vehicle carefully to the ground.
3. Dispose of waste oil and filter properly.
8-14Maintenance and do-it-yourself
wÐ
Ð
05/15/09Ðpattie
X

9 Technical and consumer information
Capacities and recommended fuel/lubricants........ 9-2
Fuel recommendation ........................... 9-4
Engine oil and oil filter recommendation ......... 9-6
Air conditioning system refrigerant and
lubricant recommendations ..................... 9-7
Specifications ..................................... 9-8
Engine ........................................ 9-8
Wheels and tires ............................... 9-9
Dimensions and weights ....................... 9-10
When traveling or registering your vehicle in
another country .................................. 9-10
Vehicle identification .............................. 9-11
Vehicle Identification Number (VIN) plate......... 9-11
Vehicle identification number
(chassis number) ............................... 9-11
Engine serial number .......................... 9-12
F.M.V.S.S./C.M.V.S.S. certification label .........9-12
Emission control information label ..............9-12
Tire and loading information label ..............9-13
Air conditioner specification label ...............9-13Installing front license plate
.......................9-14
Vehicle loading information ........................9-15
Terms ......................................... 9-15
Vehicle load capacity .......................... 9-16
Loading tips .................................. 9-17
Measurement of weights ....................... 9-18
Towing a trailer .................................. 9-18
Flat towing ...................................... 9-19
Automatic transmission ........................ 9-19
Uniform tire quality grading .......................9-19
Treadwear .................................... 9-19
Traction AA, A, B and C ........................ 9-20
Temperature A, B and C ....................... 9-20
Emission control system warranty .................9-20
Reporting safety defects (US only) .................9-21
Readiness for Inspection/Maintenance (I/M) test ....9-22
Event Data Recorders (EDR) .......................9-23
Owner's Manual/Service Manual order
information ...................................... 9-23
In the event of a collision ......................9-24
wÐ
Ð
05/19/09Ðtbrooks
X

The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure instructed in the ª8.
Maintenance and do-it-yourselfº section to determine the proper refill capacity.
Capacity (Approximate)Recommended specifications
US measure
Imp measureLiter
Fuel 20 gal 16-5/8 gal 76 See ªFUEL RECOMMENDATIONº later in this section.
Engine oil*1
Drain and refill With oil filter change VK45DE AWD 6-1/8 qt 5-1/8 qt 5.8 ·Engine oil with API Certification Mark*2, *3
·Viscosity SAE 5W-30*2, *3
2WD 5-7/8 qt 4-7/8 qt 5.5
VQ35HR AWD/2WD 5-1/8 qt 4-3/8 qt 4.9
Without oil filter change VK45DE AWD 5-1/2 qt 4-5/8 qt 5.2
2WD 5-1/8 qt 4-3/8 qt 4.9
VQ35HR AWD/2WD 4-7/8 qt 4 qt 4.6
Cooling system With reservoir VK45DE 11 qt 9-1/8 qt 10.4 50% Genuine NISSAN Long Life Antifreeze/Coolant or equivalent
50% Demineralized or distilled water
VQ35HR 9-3/4 qt 8-1/8 qt 9.2
Reservoir 7/8 qt 3/4 qt 0.8
Automatic Transmission Fluid (ATF) ÐÐÐ Genuine NISSAN Matic S ATF*4
Differential gear oil ÐÐÐ Genuine NISSAN Differential Oil Hypoid Super GL-5, 80W-90 or API
GL-5, Viscosity SAE 80W-90*5
Transfer fluid ÐÐÐ Genuine NISSAN Matic J ATF*6
Power Steering Fluid (PSF) Refill to the proper oil level according to
the instructions in the ª8. Maintenance
and do-it-yourselfº section. Genuine NISSAN PSF or equivalent*7
Brake fluid Genuine NISSAN Super Heavy Duty Brake Fluid*8 or equivalent DOT 3
CAPACITIES AND RECOMMENDED
FUEL/LUBRICANTS
9-2Technical and consumer information
wÐ
Ð
05/15/09Ðpattie
X

Capacity (Approximate)Recommended specifications
US measure
Imp measureLiter
Multi-purpose grease NLGI No. 2 (Lithium soap base)
Air conditioning system refrigerant ÐÐÐ HFC-134a (R-134a)*9
Air conditioning system lubricants ÐÐÐ NISSAN A/C System Oil Type S or exact equivalent
Window washer fluid ÐÐÐ Genuine NISSAN Windshield Washer Concentrate Cleaner & Anti-
freeze or equivalent
*1:For additional information, see ªENGINE OILº in the ª8. Maintenance and do-it-yourselfº section for changing engine oil.
*2: For additional information, see ªENGINE OIL AND OIL FILTER RECOMMENDATIONº later in this section.
*3: INFINITI recommends Genuine NISSAN Ester Oil available at your INFINITI retailer.
*4: For 5-speed AT: If Genuine NISSAN Matic S ATF is not available, Genuine NISSAN Matic J ATF may also be used. Using automatic transmission fluid other than Genuine NISSAN Matic
S ATF or Matic J ATF will cause deterioration in driveability and automatic transmission durability, and may damage the automatic transmission, which is not covered by the INFINITI
new vehicle limited warranty.
For 7-speed AT: Using automatic transmission fluid other than Genuine NISSAN Matic S ATF will cause deterioration in driveability and automatic transmission durability, and may
damage the automatic transmission, which is not covered by the INFINITI new vehicle limited warranty.
*5: For hot climates, viscosity SAE 90 is suitable for ambient temperatures above 32ÉF (0ÉC).
*6:
If Genuine NISSAN Matic J ATF is not available, Genuine NISSAN Matic D ATF or Canada NISSAN Automatic Transmission Fluid or equivalent (if
available) may also be used.
*7:
DEXRONTMVI type ATF or Canada NISSAN Automatic Transmission Fluid may also be used.
*8: Available in mainland US through an INFINITI retailer.
*9: For additional information, see ªVEHICLE IDENTIFICATIONº later in this section for air conditioner specification label.
Technical and consumer information9-3
wÐ
Ð
05/15/09Ðpattie
X

1. API certification mark
2. API service symbol
ENGINE OIL AND OIL FILTER
RECOMMENDATION
Selecting the correct oil
It is essential to choose the correct grade,
quality, and viscosity engine oil to ensure sat-
isfactory engine life and performance, see ªCA-
PACITIES AND RECOMMENDED
FUEL/LUBRICANTSº earlier in this section.
INFINITI recommends the use of an energy
conserving oil in order to improve fuel economy.Select only engine oils that meet the American
Petroleum Institute (API) certification or Interna-
tional Lubricant Standardization and Approval
Committee (ILSAC) certification and SAE viscos-
ity standard. These oils have the API certifica-
tion mark on the front of the container. Oils
which do not have the specified quality label
should not be used as they could cause engine
damage.
Oil additives
INFINITI does not recommend the use of oil
additives. The use of an oil additive is not
necessary when the proper oil type is used and
maintenance intervals are followed.Oil which may contain foreign matter or has
been previously used should not be used.
Oil viscosity
The engine oil viscosity or thickness changes
with temperature. Because of this, it is impor-
tant to select the engine oil viscosity based on
the temperatures at which the vehicle will be
operated before the next oil change. Choosing
an oil viscosity other than that recommended
could cause serious engine damage.
Selecting the correct oil filter
Your new vehicle is equipped with a high-
quality genuine NISSAN oil filter. When replac-
ing, use the genuine oil filter or its equivalent
for the reason described in ªChange intervalsº.
Change intervals
The oil and oil filter change intervals for your
engine are based on the use of the specified
quality oils and filters. Using engine oil and a
filter other than the specified quality, or exceed-
ing recommended oil and filter change intervals
could reduce engine life. Damage to the engine
caused by improper maintenance or use of
incorrect oil and filter quality and/or viscosity is
not covered by the INFINITI new vehicle limited
warranty.
STI0505
9-6Technical and consumer information
wÐ
Ð
05/15/09Ðpattie
X

Your engine was filled with a high quality
engine oil when it was built. You do not have to
change the oil before the first recommended
change interval. Oil and filter change intervals
depend upon how you use your vehicle.
Operation under the following conditions may
require more frequent oil and filter changes.
crepeated short distance driving at cold out-
side temperatures,
c driving in dusty conditions,
c extensive idling,
c stop and go commuting
Refer to the ªINFINITI Service and Maintenance
Guideº for the maintenance schedule.
AIR CONDITIONING SYSTEM
REFRIGERANT AND LUBRICANT
RECOMMENDATIONS
The air conditioning system in your INFINITI ve-
hicle must be charged with the refrigerant HFC-
134a (R-134a) and the oil, NISSAN A/C system oil
Type S or the exact equivalents.
CAUTION
The use of any other refrigerant or oil will cause
severe damage to the air conditioning system
and will require the replacement of all air con-
ditioner system components.
The refrigerant HFC-134a (R-134a) in your
INFINITI vehicle will not harm the earth's ozone
layer. Although this refrigerant does not affect
the earth's atmosphere, certain governmental
regulations require the recovery and recycling
of any refrigerant during automotive air condi-
tioning system service. Your INFINITI retailer
has the trained technicians and equipment
needed to recover and recycle your air condi-
tioning system refrigerant.
Contact an INFINITI retailer when servicing your
air conditioning system.
Technical and consumer information9-7
wÐ
Ð
05/15/09Ðpattie
X

C
Cabin air filter .................4-33
Capacities and recommended
fuel/lubricants ..................9-2
Car phone or CB radio .............4-73
Cargo (See vehicle loading information) . . .2-43
Cargo net ....................2-43
Catalytic converter, Three way catalyst . . . .5-2
CD/CF care and cleaning ...........4-57
Center multi-function control panel ......4-2
Child restraints .................1-19
Child restraints Booster seats ................1-35
Installation using LATCH .........1-24
Installation using the seat belts .....1-28
LATCH system ................ 1-21
Precautions on child restraints ......1-19
Top tether strap .............. 1-23
Child safety ...................1-14
Child safety rear door lock ...........3-6
Chimes, Audible reminders ..........2-20
Cigarette lighter and ashtrays ........2-39
Circuit breaker, Fusible link ..........8-26
Cleaning exterior and interior ......7-2 , 7-4
Climate control Automatic climate control .........4-29
Climate control rear switch ..........4-33
Climate controlled seats ............2-35
Clock ......................2-38
Coat hooks ...................2-43
Cockpit ......................2-2
Cold weather driving ..............5-56
Command (See Bluetooth THands-Free Phone
System) .................4-76 , 4-89 Compact Disc (CD) player/changer
......4-45
Compact spare tire ..............8-44
CompactFlash (CF) player ...........4-47
Compass .....................2-9
Console box ..................2-42
Controller, Center multi-function control
panel .......................4-4
Controls Control panel button (display) .......4-2
Heater and air conditioner controls (See
automatic climate control) ........4-29
Coolant
Capacities and recommended fuel/
lubricants ...................9-2
Changing engine coolant .........8-11
Checking engine coolant level ......8-11
Corrosion protection ..............7-6
Cruise control ..................5-23
Cruise control Fixed speed cruise control (on ICC
system) ...................5-42
Intelligent cruise control (ICC) system . . 5-25
Cup holders ...................2-40
D
Daytime running light system .........2-31
Defroster switch, Rear window and outside
mirror defroster switch ............2-28
Dimensions and weights ...........9-10
Display cleaning .................4-5
Display controls (See center multi-function
control panel) ..................4-2
Door open warning light ............2-14
Dot matrix liquid crystal display .......2-21Drive belts
...................8-19
Drive positioner ................3-26
Driving All-wheel drive (AWD) ...........5-47
All-wheel drive (AWD) safety
precautions .................5-7
Cold weather driving ...........5-56
Driving with automatic transmission . . . 5-11
Precautions when starting and driving . . 5-2
DS (Drive Sport) mode .............5-13
DVD player, INFINITI mobile entertainment
system .....................4-62
E
Economy, Fuel .................5-46
Emission control information label ......9-12
Emission control system warranty ......9-20
Engine Before starting the engine .........5-10
Break-in schedule ............. 5-46
Capacities and recommended fuel/
lubricants ..................9-2
Changing engine coolant .........8-11
Changing engine oil and filter ......8-12
Checking engine coolant level ......8-11
Checking engine oil level .........8-12
Engine block heater ............5-57
Engine compartment check locations . . . 8-6
Engine cooling system ..........8-10
Engine oil .................. 8-12
Engine oil and oil filter
recommendation ..............9-6
Engine oil viscosity .............9-6
Engine serial number ...........9-12
10-2
wÐ
Ð
05/15/09Ðpattie
X