height INFINITI M 2010 Owners Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2010, Model line: M, Model: INFINITI M 2010Pages: 445, PDF Size: 6.15 MB
Page 24 of 445

Forward and backward :
Moving the switch
s1forward or backward will
slide the seat forward or backward to the
desired position.
Reclining :
Move the recline switch
s2backward until the
desired angle is obtained. To bring the seatback
forward again, move the switch
s2forward.
The reclining feature allows adjustment of the
seatback for occupants of different sizes for
added comfort and to help obtain proper seat
belt fit. (See ªPRECAUTIONS ON SEAT BELT
USAGEº later in this section.) Also, the seatback can be reclined to allow occupants to rest when
the vehicle is stopped and the transmission is
in the P (Park) position with the parking brake
fully applied.
Seat lifter :
Push the front or rear end of the switch up or
down to adjust the angle of the front portion or
height of the seat.
SSS0474SSS0475
Safety Ð Seats, seat belts and supplemental restraint system1-3
wÐ
Ð
05/14/09Ðpattie
X
Page 36 of 445

Small children
Children that are over 1 year old and weigh at
least 20 lb (9 kg) can be placed in a front-facing
child restraint. Refer to the manufacturer's in-
structions for minimum and maximum weight
and height recommendations. INFINITI recom-
mends that small children be placed in child
restraints that comply with Federal Motor Ve-
hicle Safety Standards or Canadian Motor Ve-
hicle Safety Standards. You should choose a
child restraint that fits your vehicle and always
follow the manufacturer's instructions for in-
stallation and use.
Larger children
Children who are too large for child restraints
should be seated and restrained by the seat
belts which are provided. The seat belt may not
fit properly if the child is less than 4 ft 9 in
(142.5 cm) tall and weighs between 40 lb (18 kg)
and 80 lb (36 kg). A booster seat should be
used to obtain proper seat belt fit.
INFINITI recommends that a child be placed in a
commercially available booster seat if the
shoulder belt in the child's seating position fits
close to the face or neck or if the lap portion of
the seat belt goes across the abdomen. The
booster seat should raise the child so that the
shoulder belt is properly positioned across the
top, middle portion of the shoulder and the lapbelt is low on the hips. A booster seat can only
be used in seating positions that have a three-
point type seat belt. The booster seat should fit
the vehicle seat and have a label certifying that
it complies with Federal Motor Vehicle Safety
Standards or Canadian Motor Vehicle Safety
Standards. Once the child has grown so the
shoulder belt is no longer on or near the face
and neck, use the shoulder belt without the
booster seat.
WARNING
Never let a child stand or kneel on any seat and
do not allow a child in the cargo areas while the
vehicle is moving. The child could be seriously
injured or killed in an accident or sudden stop.
PREGNANT WOMEN
INFINITI recommends that pregnant women use
seat belts. The seat belt should be worn snug,
and always position the lap belt as low as
possible around the hips, not the waist. Place
the shoulder belt over your shoulder and across
your chest. Never run the lap/shoulder belt over
your abdominal area. Contact your doctor for
specific recommendations.
INJURED PERSONS
INFINITI recommends that injured persons use
seat belts, depending on the injury. Check with
your doctor for specific recommendations.
PRE-CRASH SEAT BELTS (front seats)
The pre-crash seat belt tightens the seat belt to
help restrain front seat occupants under emer-
gency braking. This can help reduce the risk of
injury when a collision occurs.
Pre-crash seat belt will not be activated when:
c
the brake pedal is not depressed
c the seat belt is not fastened
c the selector lever is in the R (Reverse) posi-
tion
c the vehicle speed is under 10 MPH (15 km/h)
Always wear your seat belt correctly and sit
upright and well back in the seat with both feet
on the floor.
If the seat belt warning light blinks even if the
driver's and front passenger's seat belts are
fastened, it may indicate the pre-crash seat belt
system has a malfunction. Have your INFINITI
retailer check and repair the system.
Safety Ð Seats, seat belts and supplemental restraint system1-15
wÐ
Ð
05/14/09Ðpattie
X
Page 39 of 445

Center of rear seat
Selecting correct set of seat belts :
The center seat belt buckle is identified by the
CENTER mark
sA. The center seat belt tongue
can be fastened onlyinto the center seat belt
buckle.
Shoulder belt height adjustment
(front seats)
The shoulder belt anchor height should be
adjusted to the position best for you. (See
ªPRECAUTIONS ON SEAT BELT USAGEº earlier in
this section.)
To adjust, push the adjustment button
sA, and
then move the shoulder belt anchor to the
desired position, so that the belt passes over
the center of the shoulder. The belt should be
away from your face and neck, but not falling off
of your shoulder. Release the adjustment but-
ton to lock the shoulder belt anchor into posi-
tion.
WARNING
c After adjustment, release the adjustment
button and try to move the shoulder belt
anchor up and down to make sure it is se-
curely fixed in position.
c The shoulder belt anchor height should be
adjusted to the position best for you. Failure
to do so may reduce the effectiveness of the
entire restraint system and increase the
chance or severity of injury in an accident.
SEAT BELT EXTENDERS
If, because of body size or driving position, it is
not possible to properly fit the lap-shoulder belt
and fasten it, an extender is available that is
compatible with the installed seat belts. The
extender adds approximately 8 in (200 mm) of
length and may be used for either the driver or
front passenger seating position. See an
INFINITI retailer for assistance if an extender is
required.
WARNING
cOnly INFINITI seat belt extenders, made by
the same company which made the original
equipment seat belts, should be used with
the INFINITI seat belts.
SPA1836SSS0294A
1-18Safety Ð Seats, seat belts and supplemental restraint system
wÐ
Ð
05/14/09Ðpattie
X
Page 42 of 445

sure the child restraint is compatible with
your child. Choose a child restraint that is
designed for your child's height and weight.
Always follow all recommended procedures.
All U.S. states and Canadian provinces or territo-
ries require that infants and small children be
restrained in an approved child restraint at all
times while the vehicle is being operated. Cana-
dian law requires the top tether strap on front-
facing child restraints be secured to the desig-
nated anchor point on the vehicle.
LOWER ANCHORS AND TETHERS FOR
CHILDREN SYSTEM (LATCH)
Your vehicle is equipped with special anchor
points that are used with Lower Anchors and
Tethers for CHildren System (LATCH) compatible
child restraints. This system may also be re-
ferred to as the ISOFIX or ISOFIX compatible
system. With this system, you do not have to
use a vehicle seat belt to secure the child
restraint. The LATCH anchor points are provided to install
child restraints in the rear outboard seating
positions only. Do not attempt to install a child
restraint in the center position using the LATCH
anchors.
LATCH system anchor location
SSS0567
Safety Ð Seats, seat belts and supplemental restraint system1-21
wÐ
Ð
05/14/09Ðpattie
X
Page 154 of 445

CAUTION
cDo not store the main sun visor before stor-
ing the sub-sun visor and the extension sun
visor.
c Do not pull the sub-sun visor and the exten-
sion sun visor forcedly downward.
1. To block out glare from the front, swing
down the main sun visor
s1.
2. To block glare from the side, remove the main sun visor from the center mount and
swing it to the side
s2.
3. To block glare from the front, swing down the sub-sun visor
s3.
4. Draw out the extension sun visor
s4from
the main sun visor to block from further
glare.
INSIDE MIRROR
Adjust the height and the angle of the inside
mirror to the desired position.
SPA2447
Type A
SPA2422A
Type B
SPA2450
MIRRORS
Pre-driving checks and adjustments3-23
wÐ
Ð
05/14/09Ðpattie
X
Page 389 of 445

If you wax the surface of the hood, be careful
not to let wax get into the washer nozzle
sA.
This may cause clogging or improper wind-
shield washer operation. If wax gets into the
nozzle, remove it with a needle or small pin
sB. If the brakes do not operate properly, have the
brakes checked by an INFINITI retailer.
SELF-ADJUSTING BRAKES
Your vehicle is equipped with self-adjusting
brakes.
The disc-type brakes self-adjust every time the
brake pedal is applied.
WARNING
See an INFINITI retailer for a brake system
check if the brake pedal height does not return
to normal.
BRAKE PAD WEAR WARNINGS
The disc brake pads have audible wear warn-
ings. When a brake pad requires replacement, it
will make a high pitched scraping sound when
the vehicle is in motion. This scraping sound
will first occur only when the brake pedal is
depressed. After more wear of the brake pad,
the sound will always be heard even if the brake
pedal is not depressed. Have the brakes
checked as soon as possible if the wear warn-
ing sound is heard.
Under some driving or climate conditions, occa-
sional brake squeak, squeal or other noise may
be heard. Occasional brake noise during light to moderate stops is normal and does not affect
the function or performance of the brake sys-
tem.
Proper brake inspection intervals should be fol-
lowed.
For additional information, see the main-
tenance log section of your ªINFINITI Service
and Maintenance Guideº.
SDI1832
BRAKES
8-24Maintenance and do-it-yourself
wÐ
Ð
05/15/09Ðpattie
X
Page 403 of 445

TIRE LABELING
Federal law requires tire manufacturers
to place standardized information on the
sidewall of all tires. This information
identifies and describes the fundamen-
tal characteristics of the tire and also
provides the tire identification number
(TIN) for safety standard certification.
The TIN can be used to identify the tire in
case of a recall.
s1Tire size (example: P215/60R16 94H)
1.P: The ªPº indicates the tire is de-
signed for passenger vehicles. (Not all
tires have this information.)
2.Three-digit number (215): This num-
ber gives the width in millimeters of
the tire from sidewall edge to side-
wall edge.
3.Two-digit number (60): This number,
known as the aspect ratio, gives the
tire's ratio of height to width.
4.R: The ªRº stands for radial.
5.Two-digit number (16): This number is
the wheel or rim diameter in inches.
6.Two- or three-digit number (94): This
number is the tire's load index. It is a
measurement of how much weight
each tire can support. You may not
find this information on all tires be-
cause it is not required by law.
7.H: Tire speed rating. You should not
drive the vehicle faster than the tire
speed rating.
Example
SDI1575
Example
SDI1606
8-38Maintenance and do-it-yourself
wÐ
Ð
05/15/09Ðpattie
X
Page 408 of 445

cThe original tires have built-in tread
wear indicators. When wear indica-
tors are visible, the tire(s) should be
replaced.
cTires degrade with age and use. Have
tires, including the spare, over 6
years old checked by a qualified tech-
nician, because some tire damage
may not be obvious. Replace the tires
as necessary to prevent tire failure
and possible personal injury.
cImproper service of the spare tire may
result in serious personal injury. If it
is necessary to repair the spare tire,
contact an INFINITI retailer.
cFor additional information regarding
tires, refer to ªImportant Tire Safety
Informationº (US) or ªTire Safety In-
formationº (Canada) in the Warranty
Information Booklet.
Replacing wheels and tires
When replacing a tire, use the same size, tread
design, speed rating and load carrying capacity
as originally equipped. (See ªSPECIFICATIONSº
in the ª9. Technical and consumer informationº
section for recommended types and sizes of
tires and wheels.)
WARNING
c The use of tires other than those recom-
mended or the mixed use of tires of different
brands, construction (bias, bias-belted or ra-
dial), or tread patterns can adversely affect
the ride, braking, handling, ground clear-
ance, body-to-tire clearance, tire chain
clearance, speedometer calibration, head-
light aim and bumper height. Some of these
effects may lead to accidents and could re-
sult in serious personal injury. c
If the wheels are changed for any reason,
always replace with wheels which have the
same off-set dimension. Wheels of a differ-
ent off-set could cause premature tire wear,
degrade vehicle handling characteristics
and/or interference with the brake
discs/drums. Such interference can lead to
decreased braking efficiency and/or early
brake pad/shoe wear. See ªWHEELS AND
TIRESº in the ª9. Technical and consumer
informationº section of this manual for
wheel off-set dimensions.
c When a spare tire is mounted or a wheel is
replaced, tire pressure will not be indicated,
the TPMS will not function and the low tire
pressure warning light will flash for approxi-
mately 1 minute. The light will remain on
after 1 minute. Contact your INFINITI retailer
as soon as possible for tire replacement
and/or system resetting.
c Replacing tires with those not originally
specified by INFINITI could affect the proper
operation of the TPMS.
c Do not install a damaged or deformed wheel
or tire even if it has been repaired. Such
wheels or tires could have structural damage
and could fail without warning.
c The use of retread tire is not recommended.
Maintenance and do-it-yourself8-43
wÐ
Ð
05/15/09Ðpattie
X
Page 421 of 445

DIMENSIONS AND WEIGHTS
Overall length
(without front license plate) in (mm) 194.0 (4,928)
(with front license plate) in (mm) 194.3 (4,935)
Overall width in (mm) 71.1 (1,805)
Overall height in (mm) 59.4 (1,510)*160.1 (1,523)*2
Front tread in (mm) 60.5 (1,537)*1, *3 60.3 (1,532)*1, *4
61.1 (1,551)*2
Rear tread in (mm) 61.0 (1,550)*1, *3 60.8 (1,545)*1, *4
60.7 (1,543)*2
Wheelbase in (mm) 114.2 (2,900)
Gross Vehicle Weight Rating (GVWR) lb (kg) See the F.M.V.S.S. or C.M.V. S.S. certification label on the
driver's side center pillar.
Gross Axle Weight Rating (GAWR)
Front lb (kg)
Rear lb (kg)
*1: Two-Wheel Drive (2WD) model
*2: All-Wheel Drive (AWD) model
*3: P245/45R18 tire equipped model
*4: 245/40R19 tire equipped model When planning to travel in another country,
you
should first find out if the fuel available is
suitable for your vehicle's engine.
Using fuel with an octane rating that is too low
may cause engine damage. All gasoline ve-
hicles must be operated with unleaded gaso-
line. Therefore, avoid taking your vehicle to
areas where appropriate fuel is not available.
When transferring the registration of your ve-
hicle to another country, state, province or dis-
trict, it may be necessary to modify the vehicle
to meet local laws and regulations.
The laws and regulations for motor vehicle
emission control and safety standards vary
according to the country, state, province or
district; therefore, vehicle specifications may
differ.
When any vehicle is to be taken into another
country, state, province or district and regis-
tered, its modifications, transportation, and reg-
istration are the responsibility of the user.
INFINITI is not responsible for any inconvenience
that may result.
WHEN TRAVELING OR REGISTERING YOUR
VEHICLE IN ANOTHER COUNTRY
9-10Technical and consumer information
wÐ
Ð
05/15/09Ðpattie
X
Page 441 of 445

Remote keyless entry function, For
Intelligent Key system.............3-14
Reporting safety defects (US only) ......9-21
Roadside assistance program .........6-2
Rollover ......................5-5
Roof, Moonroof ................2-46
Safety Child seat belts ...............1-14
Reporting safety defects (US only) ....9-21
S
Satellite radio operation ...........4-44
Seat adjustment Front power seat adjustment ........1-2
Front seats ..................1-2
Rear seat adjustment ............1-4
Seat belt(s)
Child safety .................1-14
Infants .................... 1-14
Injured persons ............... 1-15
Larger children ............... 1-15
Pre-crash seat belts ............1-15
Precautions on seat belt usage ......1-12
Pregnant women .............. 1-15
Seat belt cleaning ..............7-5
Seat belt extenders ............1-18
Seat belt maintenance ...........1-19
Seat belt warning light ..........2-17
Seat belts .................. 1-12
Seat belts with pretensioners .......1-51
Shoulder belt height adjustment .....1-18
Small children ............... 1-15
Three-point type .............. 1-16
Seat(s) Driver-side memory
............3-26
Front climate controlled seats ......2-35
Rear heated seats ............. 2-34
Seats .....................1-2
Security system (INFINITI Vehicle
Immobilizer System), Engine start ......2-25
Security system, Vehicle security system . .2-24
Selector lever Shift lock release ..............5-15
Servicing air conditioner (See automatic
climate control) .............4-29 , 4-30
Servicing climate control ...........4-33
SETTING button .................4-15
Shift lock release Transmission ................5-15
Shifting, Automatic transmission .......5-11
Shoulder belt height adjustment .......1-18
Small light indicator light ...........2-20
Snow mode switch ...............2-37
Spare tire .....................9-9
Spark plugs ...................8-20
Speedometer ...................2-6
Starting Before starting the engine .........5-10
Precautions when starting and driving . . 5-2
Starting the engine ............. 5-11
STATUS button ..................4-7
Status light, Front passenger air bag . . . .1-47
Steering Power steering fluid ............8-16
Power steering system ..........5-49
Rear Active Steer system .........5-55
Steering-wheel-mounted controls for
audio .................... 4-58
Tilt/telescopic steering ..........3-22
Storage .....................2-40 Sun visors
....................3-22
Sunglasses holder ...............2-41
Sunshade (rear) ................2-47
Supplemental air bag warning labels . . . .1-52
Supplemental air bag warning light . .1-53 , 2-17
Supplemental restraint system ........1-40
Supplemental restraint system, Precautions
on supplemental restraint system ......1-40
Switch Audio control rear switch .........4-60
Autolight switch .............. 2-30
Fog light switch .............. 2-33
Hazard warning flasher switch ......2-33
Headlight switch .............. 2-29
Ignition switch automatic transmission
models ................... 5-11
Lane departure warning (LDW) system . 2-36
Power door lock switch ...........3-5
Rear window and outside mirror
defroster switch .............. 2-28
Snow mode switch ............2-37
Turn signal switch ............. 2-33
Vehicle dynamic control (VDC) off
switch .................... 2-37
Switch, climate control rear switch .....4-33
T
Tachometer ....................2-6
Temperature gauge, Engine coolant
temperature gauge ...............2-7
Theft (INFINITI Vehicle Immobilizer System),
Engine start ...................2-25
Three-way catalyst ................5-2
Tilt/telescopic steering ............3-22
10-6
wÐ
Ð
05/15/09Ðpattie
X