technical specifications INFINITI M 2010 Owners Manual

Engine oil and filter
1. Place a large drain pan under the drainplug.
2. Remove the oil filler cap.
3. Remove the drain plug
s1with a wrench
and completely drain the oil.
CAUTION
Be careful not to burn yourself, as the engine oil
is hot.
cWaste oil must be disposed of properly.
c Check your local regulations.
Perform steps 4 to 7 only when the engine oil
filter change is needed.
4. Loosen the oil filters2with an oil filter
wrench. Remove the oil filter by turning it
by hand.
5. Wipe the engine oil filter mounting sur- face with a clean rag.
CAUTION
Be sure to remove any old rubber gasket re-
maining on the mounting surface of the engine.
Failure to do so could lead to engine failure.
6. Coat the gasket on the new filter with clean engine oil.
7. Screw in the oil filter clockwise until a slight resistance is felt, then tighten ad-
ditionally more than 2/3 turn.
Oil filter tightening torque:11 to 15 ft-lb
(14.7 to 20.5 N´m)
8. Clean and re-install the drain plug with a new washer. Securely tighten the drain
plug with a wrench.
Drain plug tightening torque:22 to 29 ft-lb
(29 to 39 N´m)
Do not use excessive force.
9. Refill engine with recommended oil and install the oil filler cap securely.
CAUTION
The dipstick must be inserted in place to pre-
vent oil spillage from the dipstick hole while
filling the engine with oil.
See ªCAPACITIES AND RECOMMENDED
FUEL/LUBRICANTSº in the ª9. Technical and
consumer informationº section for drain and refill capacity. The drain and refill capacity
depends on the oil temperature and drain time.
Use these specifications for reference only.
Always use the dipstick to determine the proper
amount of oil in the engine.
10. Start the engine and check for leakage
around the drain plug and the oil filter.
Correct as required.
11. Turn the engine off and wait more than 15 minutes. Check the oil level with the
dipstick. Add engine oil if necessary.
After the operation
1. Install the engine undercover into positionas the following steps.
a. Pull the center of the small plastic clip out.
b. Hold the engine undercover into position.
c. Insert the clip through the undercover into the hole in the frame, then push the
center of the clip in to lock the clip in
place.
d. Install the other bolts that hold the un- dercover in place. Be careful not to strip
the bolts or over-tighten them.
2. Lower the vehicle carefully to the ground.
3. Dispose of waste oil and filter properly.
8-14Maintenance and do-it-yourself
wÐ
Ð
05/15/09Ðpattie
X

cThe original tires have built-in tread
wear indicators. When wear indica-
tors are visible, the tire(s) should be
replaced.
cTires degrade with age and use. Have
tires, including the spare, over 6
years old checked by a qualified tech-
nician, because some tire damage
may not be obvious. Replace the tires
as necessary to prevent tire failure
and possible personal injury.
cImproper service of the spare tire may
result in serious personal injury. If it
is necessary to repair the spare tire,
contact an INFINITI retailer.
cFor additional information regarding
tires, refer to ªImportant Tire Safety
Informationº (US) or ªTire Safety In-
formationº (Canada) in the Warranty
Information Booklet.
Replacing wheels and tires
When replacing a tire, use the same size, tread
design, speed rating and load carrying capacity
as originally equipped. (See ªSPECIFICATIONSº
in the ª9. Technical and consumer informationº
section for recommended types and sizes of
tires and wheels.)
WARNING
c The use of tires other than those recom-
mended or the mixed use of tires of different
brands, construction (bias, bias-belted or ra-
dial), or tread patterns can adversely affect
the ride, braking, handling, ground clear-
ance, body-to-tire clearance, tire chain
clearance, speedometer calibration, head-
light aim and bumper height. Some of these
effects may lead to accidents and could re-
sult in serious personal injury. c
If the wheels are changed for any reason,
always replace with wheels which have the
same off-set dimension. Wheels of a differ-
ent off-set could cause premature tire wear,
degrade vehicle handling characteristics
and/or interference with the brake
discs/drums. Such interference can lead to
decreased braking efficiency and/or early
brake pad/shoe wear. See ªWHEELS AND
TIRESº in the ª9. Technical and consumer
informationº section of this manual for
wheel off-set dimensions.
c When a spare tire is mounted or a wheel is
replaced, tire pressure will not be indicated,
the TPMS will not function and the low tire
pressure warning light will flash for approxi-
mately 1 minute. The light will remain on
after 1 minute. Contact your INFINITI retailer
as soon as possible for tire replacement
and/or system resetting.
c Replacing tires with those not originally
specified by INFINITI could affect the proper
operation of the TPMS.
c Do not install a damaged or deformed wheel
or tire even if it has been repaired. Such
wheels or tires could have structural damage
and could fail without warning.
c The use of retread tire is not recommended.
Maintenance and do-it-yourself8-43
wÐ
Ð
05/15/09Ðpattie
X

9 Technical and consumer information
Capacities and recommended fuel/lubricants........ 9-2
Fuel recommendation ........................... 9-4
Engine oil and oil filter recommendation ......... 9-6
Air conditioning system refrigerant and
lubricant recommendations ..................... 9-7
Specifications ..................................... 9-8
Engine ........................................ 9-8
Wheels and tires ............................... 9-9
Dimensions and weights ....................... 9-10
When traveling or registering your vehicle in
another country .................................. 9-10
Vehicle identification .............................. 9-11
Vehicle Identification Number (VIN) plate......... 9-11
Vehicle identification number
(chassis number) ............................... 9-11
Engine serial number .......................... 9-12
F.M.V.S.S./C.M.V.S.S. certification label .........9-12
Emission control information label ..............9-12
Tire and loading information label ..............9-13
Air conditioner specification label ...............9-13Installing front license plate
.......................9-14
Vehicle loading information ........................9-15
Terms ......................................... 9-15
Vehicle load capacity .......................... 9-16
Loading tips .................................. 9-17
Measurement of weights ....................... 9-18
Towing a trailer .................................. 9-18
Flat towing ...................................... 9-19
Automatic transmission ........................ 9-19
Uniform tire quality grading .......................9-19
Treadwear .................................... 9-19
Traction AA, A, B and C ........................ 9-20
Temperature A, B and C ....................... 9-20
Emission control system warranty .................9-20
Reporting safety defects (US only) .................9-21
Readiness for Inspection/Maintenance (I/M) test ....9-22
Event Data Recorders (EDR) .......................9-23
Owner's Manual/Service Manual order
information ...................................... 9-23
In the event of a collision ......................9-24
wÐ
Ð
05/19/09Ðtbrooks
X

The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure instructed in the ª8.
Maintenance and do-it-yourselfº section to determine the proper refill capacity.
Capacity (Approximate)Recommended specifications
US measure
Imp measureLiter
Fuel 20 gal 16-5/8 gal 76 See ªFUEL RECOMMENDATIONº later in this section.
Engine oil*1
Drain and refill With oil filter change VK45DE AWD 6-1/8 qt 5-1/8 qt 5.8 ·Engine oil with API Certification Mark*2, *3
·Viscosity SAE 5W-30*2, *3
2WD 5-7/8 qt 4-7/8 qt 5.5
VQ35HR AWD/2WD 5-1/8 qt 4-3/8 qt 4.9
Without oil filter change VK45DE AWD 5-1/2 qt 4-5/8 qt 5.2
2WD 5-1/8 qt 4-3/8 qt 4.9
VQ35HR AWD/2WD 4-7/8 qt 4 qt 4.6
Cooling system With reservoir VK45DE 11 qt 9-1/8 qt 10.4 50% Genuine NISSAN Long Life Antifreeze/Coolant or equivalent
50% Demineralized or distilled water
VQ35HR 9-3/4 qt 8-1/8 qt 9.2
Reservoir 7/8 qt 3/4 qt 0.8
Automatic Transmission Fluid (ATF) ÐÐÐ Genuine NISSAN Matic S ATF*4
Differential gear oil ÐÐÐ Genuine NISSAN Differential Oil Hypoid Super GL-5, 80W-90 or API
GL-5, Viscosity SAE 80W-90*5
Transfer fluid ÐÐÐ Genuine NISSAN Matic J ATF*6
Power Steering Fluid (PSF) Refill to the proper oil level according to
the instructions in the ª8. Maintenance
and do-it-yourselfº section. Genuine NISSAN PSF or equivalent*7
Brake fluid Genuine NISSAN Super Heavy Duty Brake Fluid*8 or equivalent DOT 3
CAPACITIES AND RECOMMENDED
FUEL/LUBRICANTS
9-2Technical and consumer information
wÐ
Ð
05/15/09Ðpattie
X

Capacity (Approximate)Recommended specifications
US measure
Imp measureLiter
Multi-purpose grease NLGI No. 2 (Lithium soap base)
Air conditioning system refrigerant ÐÐÐ HFC-134a (R-134a)*9
Air conditioning system lubricants ÐÐÐ NISSAN A/C System Oil Type S or exact equivalent
Window washer fluid ÐÐÐ Genuine NISSAN Windshield Washer Concentrate Cleaner & Anti-
freeze or equivalent
*1:For additional information, see ªENGINE OILº in the ª8. Maintenance and do-it-yourselfº section for changing engine oil.
*2: For additional information, see ªENGINE OIL AND OIL FILTER RECOMMENDATIONº later in this section.
*3: INFINITI recommends Genuine NISSAN Ester Oil available at your INFINITI retailer.
*4: For 5-speed AT: If Genuine NISSAN Matic S ATF is not available, Genuine NISSAN Matic J ATF may also be used. Using automatic transmission fluid other than Genuine NISSAN Matic
S ATF or Matic J ATF will cause deterioration in driveability and automatic transmission durability, and may damage the automatic transmission, which is not covered by the INFINITI
new vehicle limited warranty.
For 7-speed AT: Using automatic transmission fluid other than Genuine NISSAN Matic S ATF will cause deterioration in driveability and automatic transmission durability, and may
damage the automatic transmission, which is not covered by the INFINITI new vehicle limited warranty.
*5: For hot climates, viscosity SAE 90 is suitable for ambient temperatures above 32ÉF (0ÉC).
*6:
If Genuine NISSAN Matic J ATF is not available, Genuine NISSAN Matic D ATF or Canada NISSAN Automatic Transmission Fluid or equivalent (if
available) may also be used.
*7:
DEXRONTMVI type ATF or Canada NISSAN Automatic Transmission Fluid may also be used.
*8: Available in mainland US through an INFINITI retailer.
*9: For additional information, see ªVEHICLE IDENTIFICATIONº later in this section for air conditioner specification label.
Technical and consumer information9-3
wÐ
Ð
05/15/09Ðpattie
X

FUEL RECOMMENDATION
VK45DE engine
Use unleaded premium gasoline with an octane
rating of at least 91 AKI (Anti-Knock Index)
number (Research octane number 96).
If premium gasoline is not available, unleaded
regular gasoline with an octane rating of 87 AKI
number (Research octane number 91) may be
temporarily used, but only under the following
precautions:
cHave the fuel tank filled only partially with
unleaded regular gasoline, and fill up with
unleaded premium gasoline as soon as pos-
sible.
c Avoid full throttle driving and abrupt accel-
eration.
However, for maximum vehicle performance, the
use of unleaded premium gasoline is recom-
mended.
VQ35HR engine
INFINITI recommends the use of unleaded pre-
mium gasoline with an octane rating of at least
91 AKI (Anti-Knock Index) number (Research
octane number 96).
If unleaded premium gasoline is not available,
you may use unleaded regular gasoline with an octane rating of at least 87 AKI number (Re-
search octane number 91), but you may notice a
decrease in performance.
CAUTION
c
Using a fuel other than that specified could
adversely affect the emission control sys-
tem, and may also affect warranty coverage.
c Under no circumstances should a leaded
gasoline be used, because this will damage
the three-way catalyst.
c Do not use E-85 fuel in your vehicle. Your
vehicle is not designed to run on E-85 fuel.
Using E-85 fuel can damage the fuel system
components and is not covered by the
INFINITI new vehicle limited warranty.
Gasoline specifications
INFINITI recommends using gasoline that meets
the World-Wide Fuel Charter (WWFC) specifica-
tions where it is available. Many of the automo-
bile manufacturers developed this specification
to improve the emission control system and
vehicle performance. Ask your service station
manager if the gasoline meets the WWFC speci-
fications.
Reformulated gasoline
Some fuel suppliers are now producing refor-
mulated gasolines. These gasolines are spe-
cially designed to reduce vehicle emissions.
INFINITI supports efforts towards cleaner air
and suggests that you use reformulated gaso-
line when available.
Gasoline containing oxygenates
Some fuel suppliers sell gasoline containing
oxygenates such as ethanol, MTBE and metha-
nol with or without advertising their presence.
INFINITI does not recommend the use of fuels of
which the oxygenate content and the fuel com-
patibility for your INFINITI cannot be readily
determined. If in doubt, ask your service station
manager.
If you use oxygenate-blend gasoline, please
take the following precautions as the usage of
such fuels may cause vehicle performance prob-
lems and/or fuel system damage.
c The fuel should be unleaded and have an oc-
tane rating no lower than that recommended
for unleaded gasoline.
c If an oxygenate-blend other than methanol
blend is used, it should contain no more than
10% oxygenate. (MTBE may, however, be
added up to 15%.)
9-4Technical and consumer information
wÐ
Ð
05/15/09Ðpattie
X

ENGINE
ModelVK45DEVQ35HR
Type Gasoline, 4-cycle Gasoline, 4-cycle
Cylinder arrangement 8-cylinder, V-slanted at 90É6-cylinder, V-slanted at
60É
Bore ý Stroke in (mm) 3.661 ý 3.256 (93.0 ý 82.7)3.760 ý 3.205
(95.5 ý 81.4)
Displacement cu in (cm
3) 274.2 (4,494) 213.45 (3,498)
Firing order 1-8-7-3-6-5-4-21-2-3-4-5-6
Idle speed rpm No adjustment is necessary.
Ignition timing
(B.T.D.C.) degree/rpm
Spark plug Standard PLFR5A-11FXE22HR-11
Service
operation Hot PLFR4A-11
FXE20HR-11
Cold PLFR6A-11 FXE24HR-11
Spark plug gap
(Normal) in (mm)
0.043 (1.1) 0.043 (1.1)
Camshaft operation Timing chainTiming chain
This spark ignition system complies with the Canadian standard ICES-002.
VK45DE engine
STI0397B
VQ35HR engine
STI0425
SPECIFICATIONS
9-8Technical and consumer information
wÐ
Ð
05/15/09Ðpattie
X

DIMENSIONS AND WEIGHTS
Overall length
(without front license plate) in (mm) 194.0 (4,928)
(with front license plate) in (mm) 194.3 (4,935)
Overall width in (mm) 71.1 (1,805)
Overall height in (mm) 59.4 (1,510)*160.1 (1,523)*2
Front tread in (mm) 60.5 (1,537)*1, *3 60.3 (1,532)*1, *4
61.1 (1,551)*2
Rear tread in (mm) 61.0 (1,550)*1, *3 60.8 (1,545)*1, *4
60.7 (1,543)*2
Wheelbase in (mm) 114.2 (2,900)
Gross Vehicle Weight Rating (GVWR) lb (kg) See the F.M.V.S.S. or C.M.V. S.S. certification label on the
driver's side center pillar.
Gross Axle Weight Rating (GAWR)
Front lb (kg)
Rear lb (kg)
*1: Two-Wheel Drive (2WD) model
*2: All-Wheel Drive (AWD) model
*3: P245/45R18 tire equipped model
*4: 245/40R19 tire equipped model When planning to travel in another country,
you
should first find out if the fuel available is
suitable for your vehicle's engine.
Using fuel with an octane rating that is too low
may cause engine damage. All gasoline ve-
hicles must be operated with unleaded gaso-
line. Therefore, avoid taking your vehicle to
areas where appropriate fuel is not available.
When transferring the registration of your ve-
hicle to another country, state, province or dis-
trict, it may be necessary to modify the vehicle
to meet local laws and regulations.
The laws and regulations for motor vehicle
emission control and safety standards vary
according to the country, state, province or
district; therefore, vehicle specifications may
differ.
When any vehicle is to be taken into another
country, state, province or district and regis-
tered, its modifications, transportation, and reg-
istration are the responsibility of the user.
INFINITI is not responsible for any inconvenience
that may result.
WHEN TRAVELING OR REGISTERING YOUR
VEHICLE IN ANOTHER COUNTRY
9-10Technical and consumer information
wÐ
Ð
05/15/09Ðpattie
X